Clarke CPPRSS, 6499630 User guide

MODEL NO: CPPRSS

PART NO:

PART NO: 6499630

CHEMICAL PLUNGER PUMP

INTRODUCTION

Thank you for purchasing this CLARKE chemical plunger pump,

Suitable for water, alcohol, petroleum, diesel, paraffin, lubricant, water-based chemicals, acid and alkaline solutions.

Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully.

LIST OF CONTENTS

•1 x Pump •1 x Outlet tube

• 1 x Handle assembly • 1 x Extension Inlet tube

• 2 x Nuts and Bolts • 1 x 2 piece telescopic extension with filter

ASSEMBLY

FITTING THE OUTLET TUBE

1. Remove the nut from the pump as shown. 2. Place the nut over the outlet tube and back
onto the pump

FITTING THE HANDLE ASSEMBLY

FITTING THE TELESCOPIC EXTENSION TUBE

1. Connect the handle as shown and secure at

each point using the small nuts and bolts.

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

1. Fit the telescopic extension with filter together
as shown

FITTING THE PUMP TO A BARREL

1. Fit the telescopic extension with filter to the pump.

• You can fit the extension inlet tube in between if
required.

2. Adjust the telescopic extension tube to the required length.

• The bottom of the telescopic extension should be just off
of the bottom of the barrel when fitted.

3. Screw the pump into the threaded opening of the barrel.

USING THE PUMP

1. Place a suitable container under the outlet tube.

2. Pump the handle to draw fluid from the barrel.

• The first time you use the pump, you may need to pump
the handle a few times to prime the pump.

• Each ‘pump’ of the handle will draw approximately 0.3L
of fluid.

SPECIFICATIONS

Container Adaptor Size 2" BSP

Max Flow 0.3 litres per stroke

Inlet Tube Length 300 mm

Inlet Tube Diameter 21.5mm

Outlet Tube Diameter 16.7mm

Maximum Drum Size 205 litres

Min-Max Height (with extension tube fitted) 1130 - 1400 mm

Dims (W x D x H) 485 x 90 x 1400 mm (fully extended)

Product Weight 1.2kg

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12 months from the date of
purchase. Please keep your receipt which will be required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not
used for the purpose for which it was intended.

Faulty goods should be returned to their place of purchase, no product can be returned to us without prior
permission.

This guarantee does not effect your statutory rights.

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

CHEMICAL RESISTANCE TABLE

• Room Temperature

•% Say Mass Concentration

WATER ACIDS ALKALI PETROLEUM

BASED

Sea Water Acetic Acid

20%

Boric Acid
10%

Citric Acid
10%

Formic Acid Soap Solution Isopropanol

Hydraulic
Acid 35%

Lactic Acid
80%

Nitric Acid
30%

Oxalic Acid
50%

Potassium
Hydroxide
25%

Sodium
Hydroxide
solution 50%

Silicone Oil Calcium

HALOGENS ALCOHOL THINNER

Ethanol 96% Acetone

Chloride 10%

Copper
Sulphate

Potassium
Dichromate
10%

Sodium
Chloride 10%

Sodium
Nitrate 10%

Sodium
Thiosulphate

Zinc Chloride
10%

Glycerine

Glycol

Methanol

Propanol

Phosphoric
Acid 50%

Sulphuric
Acid 80%

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]