Clarke CMS 10, 6501305 User guide

10” COMPOUND MITRE SAW

10” COMPOUND MITRE SAW

Model CMS10

Part Number 6501305

Operating & Maintenance

Instructions

© 02/08

SPECIFICATIONS

Motor: ........................................ 230V 50Hz 1 phase.

Input Current ..............................8.35 Amps

Power Rating: ............................ 1600 Watts

Speed: .......................................4800 RPM

Fuse Rating ............................... 13 Amps

Dimensions: (Head Lowered) ......(H) 375 x (W) 767 x (D) 545 mm

Dimensions: (Head Raised) ........ (H) 575 x (W) 767 x (D) 545 mm

Blade type/size: (Fitted) .............TCT/ 255 mm, 30 mm bore, 60T

Drive Spindle Diameter ...............16 mm

Dust Port Diameter ....................31/37 mm (Inner/Outer)

Sound Power level (measured) ... 99.3 dBLWA

Vibration Level ............................<2.5 m/s² (Normal Load)

Net weight .................................. 11.5 kg

Part Number ...............................6501305

Maximum Cutting Sizes

Type of Cut Depth Thickness

Cross (90°) 65mm 130mm

Mitre(45°) 65mm 90mm

Bevel (at 45°) 40mm 130mm

Compound (at 2x 45°) 90mm 32mm

Please note that the details and specifications contained herein, are correct at the

time of going to print. However, CLARKE International reserve the right to change

specifications at any time without prior notice. Always consult the machine’s data

DO NOT dispose of theis product with general household waste. It must be disposed
of in accordance with all laws governing waste electrical and electronic equipment
at a recognised disposal facility.

plate

PARTS & SERVICING

For Parts & Servicing, please contact your nearest dealer, or

CLARKE International, on one of the following numbers.

PARTS & SERVICE TEL: [phone]

PARTS & SERVICE FAX: [phone]

or e-mail as follows:

PARTS: [e-mail]

SERVICE: [e-mail]

2

Thank you for purchasing this CLARKE 10 inch Compound Mitre Saw which
is designed for DIY/hobby and medium trade use only.

Before operating the Mitre Saw please read this leaflet thoroughly and
carefully follow all instructions. This will ensure the safety of yourself and
that of others around you, and you can also look forward to the machine
giving you long and satisfactory service.

GUARANTEE

This CLARKE product is guaranteed against faulty manufacture for a period
of 12 months from the date of purchase. Please keep your receipt as proof
of purchase. This guarantee is invalid if the product is found to have been
abused or tampered with in any way, or not used for the purpose for
which it was intended.

Faulty goods should be returned to their place of purchase, no product
can be returned to us without prior permission.

This guarantee does not effect your statutory rights.

CONTENTS

Specifications ......................................................................... 2

Maximum Cutting Sizes ......................................................... 2

Safety Precautions ................................................................. 4

Additional Precautions for Mitre Saws ................................ 6

Electrical Connections .......................................................... 7

Principle Parts ........................................................................ 8

Features ............................................................................ 9

Assembly ............................................................................ 10

Operation Cross Cutting ..................................................... 10

Mitre Cutting ...................................................... 11

Bevel Cutting ..................................................... 12

Compound Mitre Cutting ................................ 12

Maintenance ......................................................................... 13

Blade renewal .................................................... 13

Adjustments ............................................................................ 15

Parts Lists and Diagrams ....................................................... 16 - 17

3

SAFETY PRECAUTIONS

GENERAL SAFETY RULES FOR OPERATING MACHINERY

WARNING:

As with all machinery, there are certain hazards involved with their

operation and use. Exercising respect and caution will considerably

lessen the risk of personal injury. However, if normal safety precautions

are overlooked or ignored, personal injury to the operator or damage to

property, may result.

1. READ and BECOME FAMILIAR with the entire operating manual. Learn
the machines’ applications and limitations as well as the specific
potential hazards peculiar to it.

2. EARTH ALL MACHINES. If the machine is equipped with three-pin plug,
it should be plugged into a three-pin electrical socket. Never remove
the earth pin.

3. ALWAYS ensure that ADEQUATE LIGHTING is available. A minimum
intensity of 300 lux should be provided. Ensure that lighting is placed
so that you will not be working in your own shadow.

4. CHECK for DAMAGE. Before using the machine, any damaged part,
such as a guard etc., should be checked to ensure that it will operate
properly, and perform its intended function. Check for alignment of
moving parts, breakage of parts, mountings, and any other condition
that may affect the machines’ operation. Any damage should be
properly repaired or the part replaced. If in doubt, DO NOT USE the
machine. Consult your local dealer.

5. DISCONNECT the MACHINE from the power supply before servicing
and when changing accessories such as blades, etc.

6. KEEP GUARDS in place and in working order.

7. ALWAYS WEAR SAFETY GOGGLES, manufactured to the latest European
Safety Standards. Also use a face or dust mask if the cutting operation
is dusty. Everyday eyeglasses do not have impact resistant lenses, they
are NOT safety glasses.

8. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.

9. ALWAYS WEAR EAR PROTECTORS/DEFENDERS as this machine generates
considerable noise which can be in excess of 97dBA.

10. DON’T FORCE the machine. It will do a better and safer job at the rate
for which it was designed.

4

11. REMOVE ADJUSTING KEYS AND WRENCHES. Form the habit of checking
to see that keys and adjusting wrenches are removed from the
machine before switching on.

12. DRUGS, ALCOHOL, MEDICATION. Do not operate machine while under
the influence of drugs, alcohol or any medication.

13. USE RECOMMENDED ACCESSORIES. The use of improper accessories
could be hazardous.

14. NEVER LEAVE MACHINE RUNNING UNATTENDED. Turn power OFF. Do
not leave machine until it comes to a complete stop.

15. ALWAYS REMOVE PLUG from electrical outlet when adjusting, changing
parts, or working on machine.

16. AVOID DANGEROUS ENVIRONMENT. Don’t use power machines in damp
or wet locations or expose them to rain. Keep your work area well
illuminated. DO NOT USE in explosive atmosphere (around paint,
flammable liquids etc.).

17. KEEP CHILDREN AWAY. All visitors should be kept a safe distance from
the work area, especially whilst operating the unit.

19. MAINTAIN MACHINE IN TOP CONDITION. Keep tools sharp and clean
for the best and safest performance. Follow maintenance instructions.

21. DON’T OVERREACH. Keep your proper footing and balance at all times.
For best footing, wear rubber soled footwear. Keep floor clear of oil,
scrap wood, etc.

22. WEAR PROPER APPAREL. Loose clothing or jewelry may get caught in
moving parts. Wear protective hair covering to contain long hair.

23. MAKE WORKSHOP CHILDPROOF. Cover the saw adequately when not
in use, to prevent children from damaging themselves by tampering
with it.

24. NEVER STAND ON THE MACHINE. Serious injury could occur if the
machine is tipped or if a cutting tool is accidentally contacted. Do
not store materials above or near a machine, such that it is necessary
to stand on the machine to reach them.

25. HANDLE WITH EXTREME CARE Whenever transporting or installing
machinery, and always use a lifting tool.

26. AVOID ACCIDENTAL STARTING. Ensure the switch is OFF before plugging
in to mains.

27. BE AWARE that ACCIDENTS are caused by carelessness due to familiarity.
ALWAYS concentrate on the job in hand, no matter how trivial it may seem.

5

ADDITIONAL SAFETY INSTRUCTIONS

for MITRE SAWS

1. Wear safety goggles as protection against flying wood chips and saw dust. In
many cases, a full face shield is even better protection. A dust mask is also
recommended to keep saw dust out of your lungs.

2. Use a solid wood workbench which will not move under load.

3. This saw is for indoor, DIY or medium trade use only.

4. Clear the work table of all objects except the workpiece (tools, scraps, rulers
etc.) before switching on the saw.

5. Keep your fingers well away from the blade.

6. Switch off the saw, and make sure the blade has come to a complete stop
before clearing sawdust or off-cuts from the table.

7. Make sure there are no nails or foreign objects in the part of the workpiece to
be sawn.

8. Set up the machine and make all adjustments with the power OFF, and
disconnected from the supply.

9. DO NOT operate the machine with the guards removed. They must all be in
place and securely fastened when performing any operation.

10. Use ONLY approved replacement saw blades. Contact your local CLARKE
dealer for advice. The use of inferior blades may increase the risk of injury.

11. DO NOT saw any material that does not have a flat surface on which to bear.

12. This machine is designed for cutting wood. DO NOT use for cutting metal,
plastics or masonry.

13. Do Not force the blade, lower it gently into the work.

14. Ensure you have complete control of the Cutting Head at all times. When a cut
is completed, return it to its uppermost position gently. DO NOT allow it to snap
back heavily under spring pressure.

15. Always clamp the work to the table...DO NOT perform freehand operations.

16. Ensure that the portion of the workpiece being cut bears firmly against the
back fence.

17. Provide adequate support for long workpieces.

18. Never use solvents for cleaning plastic parts as this could cause damage to
the material. A soft damp cloth only is required.

19. The saw blade must have a rated capacity greater than the maximum speed
of the machine - see Specifications

6

ELECTRICAL CONNECTIONS

Connect the mains lead to a standard, 230 Volt (50Hz) electrical supply
through an approved 13 amp BS 1363 plug, or a suitably fused isolator
switch.

WARNING! THIS APPLIANCE IS DOUBLE INSULATED

IMPORTANT: The wires in the mains lead are coloured in accordance with
the following code:

Blue - Neutral

Brown - Live

As the colours of the flexible lead of this appliance may not correspond
with the coloured markings identifying terminals in your plug proceed as
follows:

Connect BROWN cord to terminal marked with “L” or coloured RED.

Connect BLUE cord to the terminal marked with “N” or coloured BLACK.

If this appliance is fitted with a plug which is moulded onto the electric
cable (i.e. non-rewirable) please note:

1. The plug must be thrown away if it is cut from the electric cable. There
is a danger of electric shock if it is subsequently inserted into a socket
outlet.

2. Never use the plug without the fuse cover fitted.

3. Should you wish to replace a detachable fuse carrier, ensure that the
correct replacement is used (as indicated by marking or colour code).

4. Replacement fuse covers can be obtained from your local dealer or
most electrical stockists.

Fuse Rating

The fuse in the plug must be replaced with one of the same rating -13amps
and this replacement must be ASTA approved to BS1362.

Cable Extension

If a cable extension is needed, it is essential to ensure that the size of the
conductors is at least the same size as those of the power cable supplied.

7

PRINCIPAL PARTS OF THE SAW

Fig.1

Fig.2

8

FEATURES

As its’ name implies, the machine is a Bevel/Mitre Saw, capable of straight cross
cutting, and cutting bevels and mitres, or a combination of the two.

The main arm, or Cutting Head, carries the motor and the tungsten carbide saw
blade. The head, complete with table, is allowed to swivel to produce mitre cuts
and the head may also tilt to the left to produce bevel cuts. A combination of
swivelling head and tilting head will also produce compound mitres

The table, with head, is designed to swivel up to 45 degrees in either direction and
is provided with positive stops at 90, 60, 45 and 22.5 degrees.

The maximum sizes of wood that may be cut in any of these processes is given in
the Specifications on page 3.

A dust extraction outlet is provided at the rear of the machine, on to which the dust
bag (supplied) is fitted. If necessary, hose from a vacuum cleaner may be attached
to provide fast and efficient removal of sawdust. The vacuum cleaner may be
used continuously or intermittently depending upon your requirements.

The blade drive shaft has a 16mm diameter. A 60T TCT blade is provided with a
bore of 30mm. A reducer bush is therefore used, and one spare is provided.

This saw is not designed for cutting metal, plastics or masonry.

To transport the saw, simply pick it up using the carry handle on top of the head.

NOTE: The cutting head must be in its lower position as shown below, locked in
position using the Head Locking Pin.

A saw blade spindle locking lever is provided - see Fig.3, used in order to remove
the saw blade. WARNING! NEVER touch this lever when the saw is operating.

Fig.3

9

ASSEMBLY and INSTALLATION.

The saw is fully assembled and adjusted at the factory. On receipt inspect the
machine to ensure that all parts are accounted for and that no damage was
incurred during transit.

Loose items are:

1 x socket spanner: 1 x spare set of carbon brushes.

1 x spare blade bore reducer bush. 1 x plastic 90/45O template.

1 x dust bag 1 x work clamp with support bar

1 x rear support with nut and bolt 2 x work supports

Any deficiency or damage should be reported to your CLARKE dealer immediately.

Mount the machine on a firm solid base that will not move under load. Ensure there
is an appropriate electrical supply, and adequate lighting, so that you will not be
working in your own shadow.

Four holes are provided, one at each corner of the base, so that the machine may
be bolted permanently to a workbench for added stability, using 8mm bolts (not
provided). Alternatively it may be bolted to a piece of plywood with a thickness of
16mm (5/8”).

If not bolted to a workbench, the rear support must be fitted - see Figs 1 and 2. A
single bolt secures the support to the rear of the base housing.

The Cutting Head is locked in its lower position for transit purposes. To release it, pull
out the Head Locking Pin - see Fig 3 (It may be necessary to apply slight downward
pressure to the head in order to do so), and allow the head to rise to its upper
position gently, under control.

The head will lock in its upper position, and is prevented from being lowered until
the Safety Lever (see Fig 2) is pushed to one side.

OPERATION. (Ref Fig.4)

A. Cross Cutting. (at 90°)

Set the table at 0 degrees as shown on the scale at the front of the table. To do this,
firstly unscrew the large table knob a few turns, then press down on the table locking
lever - see Fig.3, and turn the table, using the large table knob, until it clicks into place.

To secure the table, screw in the table knob fully.

Set the work in place with the left end firmly clamped against the table and back
fence.

It is important to ensure that one end of the workpiece is completely free to move
i.e. NOT clamped or held in any way. This will normally be the off-cut or shorter end.

10

NOTE: If the workpiece is not entirely straight, ensure that the portion at either side
of the intended cut rests firmly against the table and back fence.

When satisfied, make a final check to ensure that all safety precautions are being
complied with, then pull and hold the trigger and allow the blade to reach full
speed. If any unusual sounds or vibrations occur, release the starter switch
immediately and investigate the cause.

When satisfied, push the Safety Lever to one side with your thumb or forefinger and
gently lower the head so that the blade makes contact with the workpiece. Do not
force the blade, a light pressure is all that is required.

You will notice that to provide maximum safety, the blade is not exposed at any
time, and the guard rises automatically as the blade is lowered. Nevertheless,
NEVER treat the machine with indifference, and NEVER be casual with your
approach.

To switch off, release the trigger whilst still maintaining full control of the head. NEVER
allow the head to spring upwards - always maintain control. Wait for the blade to stop
completely before removing the workpiece, off-cuts etc.

B. Mitre Cutting

This is a cross cutting operation, except that the saw blade is set at an angle to the
work, but remains perpendicular to the table. This is achieved by mounting the
complete head assembly on a table which is free to rotate by up to 45° in either
direction .

To set the required mitre angle, unscrew the table knob a few turns, then depress
the table locking lever and rotate the table, with the head and saw blade, to the
desired position, using the large table knob, lining up the angle on the scale with the
pointer. Note that the table will lock in position in the 0O, 22.5O, 30O and 45O positions.
The procedure for cutting is the same as that for cross cutting.

To secure the table, screw in the table knob.

Fig.4

11

C. Straight Bevel Cutting

As with Mitre Cutting, this is a cross cutting operation, except that the blade is not
perpendicular to the table, (see fig. 5).

Ensure the table is set to 0O, and is
locked in place using the table knob.

The bevel adjuster is factory set so
that when the head is tilted to its
fullest extent the blade will cut a
perfect 45° bevel.

If however you require any other
angle, you should proceed as
follows:

Cut a mitre of the required angle,
on a spare piece of wood, and use
this as a template for your bevel cut.

Fig.6

Slacken off the bevel locking lever, and
swing the head to the side. Lower the
arm, and bring your template up to the
saw blade. When satisfied that the edge
of template and blade are parallel, lock
the head in position with locking lever.
Your angle is now set.

The procedure for cutting is the same as

that for cross cutting....press trigger, wait

for full speed to develop, push safety
lever to one side, then lower the blade
to the workpiece.

Fig.5

D. Compound Mitre and Bevel Cutting.

Having determined the angles you
require, firstly set the bevel angle, using
the procedure described above, and
then the mitre angle.

NOTE: Compound mitre and bevel
cuts, at a full 45°, can only be made
when the head is turned to the left.

The procedure for cutting is the same
as that for cross cutting.

12

MAINTENANCE

1. General

The machine is maintenance free, except for changing the saw blade when
necessary, maintaining adjustments, and ensuring that after use, you clean away
any sawdust or wood chips, with a low pressure air line or brush, paying particular
attention to the motor air vents which should be kept clear at all times.

Should the motor not function normally, it is possible that it has become clogged
with saw dust, in which case, it will be necessary to disassemble the motor in order
to clean the various components. Contact your CLARKE dealer for advice.

2. Changing the Saw Blade

IMPORTANT: Exercise extreme care when handling the saw blade. The tips are
extremely sharp, and careless handling could result in severe personal injury.

Fig.8

1. With the machine disconnected from
the mains supply, and the cutting head
in the raised position, undo and remove
the screw securing the link arm
attached to the clear plastic blade
guard, indicated in Fig.8.

Fig.9

3. Hold the blade guard in this position whilst

slackening off the screw, indicated,
sufficient for the cover to become
disengaged - note the slotted hole. It is not
necessary to remove the screw.

13

2. Move the safety lever to one side
to allow the clear plastic blade
guard to be pulled around the saw
blade as shown in Fig.9.

4. Allow the blade guard to fully reassert,
as shown in Fig.10, then unscrew and
remove the second cover screw, as
shown.

This will allow the complete blade guard
with centre hub and linkage to be
carefully pulled from the head.

Fig.10

5. Lower the saw head and lock in place

Fig.11

with the locking pin

6. With the clear plastic blade guard
removed, hold down the spindle locking
lever, arrowed in Fig. 11, and undo, but
do not remove the saw blade centre
screw, using the box spanner supplied,
by turning CLOCKWISE .i.e. The screw

has a left hand thread.

WARNING! NEVER push IN the Spindle
Locking Lever with the motor running

7. Pull out the head locking pin and allow the saw head to rise, under control, then
unscrew and remove the blade centre bolt. Finally, pull off the outer flange
followed by the saw blade.

NOTE: You should take this opportunity to thoroughly clean parts previously
inaccessible.

By removing the collar, it is possible to use blades with a 16mm bore.

8. Replace the blade, ensuring it is of the correct bore, or, where necessary a
collar is used to ensure it is a perfect fit on the shaft. Ensure also that all parts are
perfectly clean and the blades’ teeth point down at the front.

Additionally, the blade MUST be rated with a maximum speed greater that
4850RPM

Please note that spare blades are available from Clarke International. Please
see your Clarke dealer.

Replace the outer flange and screw in the centre bolt, remembering it has a
left hand thread - i.e. turn anticlockwise to tighten.

9. Replace the clear plastic blade guard in reverse order to that when
disassembling.

14

3. Carbon Brushes Replacement

A spare pair of carbon brushes are supplied with the machine. Should it become
necessary to change these, evidenced by erratic performance, then simply
unscrew the brush holder plugs, ensuring the machine is disconnected from the
mains supply, and pull out the worn brushes. Replace with new brushes, and screw
in the plug, taking care not to cross thread it.

Fig.12

4. Head Adjustments

If you find that the cross cut is not entirely square, it will be necessary to adjust the
head using the 90° adjuster screw shown in Fig. 13.

To do this, slacken off the bevel locking lever, then lower the arm and lock in place
with the head locking knob.

Place a small square on the table, and bring the square up to the blade to test for
accuracy.

Should any adjustment be required, slacken off the 90° adjuster screw lock nut and
screw the adjuster in or out, as necessary, whilst holding the head firmly against the
stop. Tighten the securing nut when the head is exactly perpendicular.

Similarly should the 45° stop require adjusting, use a 45° template up against the
saw blade to set the adjuster to the correct position.

Fig.13

15

PARTS DIAGRAM

16

PARTS LIST

No. Description Part No.

1 Circlip For Shaft 1 GRCMS1001
2 Pressure Rod 1 GRCMS1002
3 Screw M4×55 2 GRCMS1003
4 Spring Lock Washer 2 GRCMS1004
5 Screw M4×10 4 GRCMS1005
6 Cable Clip 2 GRCMS1006
7 Shaft 1 GRCMS1007
8 Split Washer 1 GRCMS1008

8-1 Screw M4.2×9 1 GRCMS1008-1

9 Split Washer 1 GRCMS1009
10 Cable Plug 1 GRCMS1010
11 Extension Spring 1 GRCMS1011
12 Push Rod 1 GRCMS1012
13 Head 1 GRCMS1013
14 Plain Washer 9 GRCMS1014
15 Spring Lock Washer 9 GRCMS1015
16 Screw M4×30 4 GRCMS1016
17 O-Ring 1 GRCMS1017
18 Stop Lever 1 GRCMS1018
19 Plain Washe 1 GRCMS1019
20 Nut M12 1 GRCMS1020
21 Nut M5 4 GRCMS1021

22 Handle (Upper) 1 GRCMS1022
23 Capacitor 1 GRCMS1023
24 Switch 1 GRCMS1024
25 Inductor 1 GRCMS1025
26 Handle (Upper Down) 1 GRCMS1026
27 Screw M4×22 3 GRCMS1027
28 Cover 1 GRCMS1028
29 Bolt M8×15(left) 1 GRCMS1029
30 Wheel Flange 1 GRCMS1030
31 Below Wheel Flange 1 GRCMS1031
32 Wheel Flange Washer 1 GRCMS1032
33 Screw M4×8 3 GRCMS1033
34 Bearing Cover plate 1 GRCMS1034
35 Protective Cover 1 GRCMS1035
36 Bearing D180201 1 GRCMS1036
37 Fore Cover 1 GRCMS1037
38 Output Spindle 1 GRCMS1038
39 Woodruff Key 1 GRCMS1039
40 Screw M5×10 1 GRCMS1040
41 Bevel Gear 1 GRCMS1041
42 Axle Elasticity Ring 12 1 GRCMS1042
43 Oil Bearing 1 GRCMS1043
44 Cable Base 1 GRCMS1044
45 Screw 1 GRCMS1045
46 Cable 1 GRCMS1046
47 Cable Armor 1 GRCMS1047
48 Rubber Washer 2 GRCMS1048
49 Cable Armor 1 GRCMS1049
50 Nut Wrench 1 GRCMS1050

No. Description Part No.

51 Lengthening Nut 1 GRCMS1051
52 Armor 1 GRCMS1052
53 Spring 2 GRCMS1053
54 Frame 1 GRCMS1054
55 Copper Washer 1 GRCMS1055
56 Spring Lock Washer 4 GRCMS1056
57 Screw M5×8 4 GRCMS1057
58 Blade Protective Plate 2 GRCMS1058
59 Socket Hd Cap Screw 4 GRCMS1059
60 Bolt M8×70 2 GRCMS1060
61 Turntable Locking Screw 3 GRCMS1061
62 Socket Hd Cap Screw 2 GRCMS1062

62-1 Socket Hd Cap Screw GRCMS1062-1

63 Washer 2 GRCMS1063
64 Nut M8 1 GRCMS1064
65 Nut M12 2 GRCMS1065
66 Frame Rotation 2 GRCMS1066
67 Spring Fixed Seat 1 GRCMS1067
68 Washer 1 GRCMS1068
69 Blade Carrier Rotation 1 GRCMS1069
70 Base 1 GRCMS1070
71 Screw M5×12 2 GRCMS1071
72 Fence 1 GRCMS1072
73 Turntable 1 GRCMS1073
74 Nut M6 4 GRCMS1074
75 Plain Washer 6 2 GRCMS1075

76 Base Table 1 GRCMS1076

77 Right-angle Piece 2 GRCMS1077
78 Basetable Washer 6 GRCMS1078
79 Screw M4×65 2 GRCMS1079
80 Brush Holder 2 GRCMS1080
81 Carbon Brush 2 GRCMS1081
82 Screw 4 GRCMS1082
83 Bearing D18201 1 GRCMS1083
84 Armature 1 GRCMS1084
85 Bearing 80029 1 GRCMS1085
86 Fan Guide 1 GRCMS1086
87 Stator 1 GRCMS1087
88 Bushing 1 GRCMS1088
89 Housing 1 GRCMS1089
90 Rear Cover 1 GRCMS1090
91 Wrench 1 GRCMS1091
92 Wrench Socket 1 GRCMS1092
93 Screw M4x16 2 GRCMS1093
94 Nut 2 GRCMS1094
95 Connection Box 1 GRCMS1095
96 Connection Box Cover 1 GRCMS1096
97 Screw 2 GRCMS1097
98 Connection Terminal 1 GRCMS1098
99 Cable Clip 1 GRCMS1099

17

18

19