Clarke CHT 612, 1801612 User guide

1.5L OIL EXTRACTOR

MODEL: CHT612

Part No: 1801612

ASSEMBLY & INSTRUCTION

MANUAL

LS1216

INTRODUCTION

Thank you for purchasing this CLARKE product

Before attempting to use the product, it is essential that you read this manual
thoroughly and carefully follow all instructions given. In doing so you will
ensure the safety of yourself and that of others around you, and you can also
look forward to the product giving you long and satisfactory service.

GUARANTEE

This CLARKE product is guaranteed against faulty manufacture for a period of
12 months from the date of purchase. Please keep your receipt as proof of
purchase.

This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for the purpose for which it was
intended.

Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.

This guarantee does not effect your statutory rights.

ENVIRONMENTAL PROTECTION

Do not dispose of this product with general household waste. All tools,
accessories and packaging should be sorted, taken to a recycling
centre and disposed of appropriately.

PARTS & SERVICE

For parts & Servicing, please contact your nearest dealer, or

CLARKE International, on one of the following numbers.

PARTS & SERVICE TEL: [phone]

PARTS & SERVICE FAX: [phone]

or e-mail as follows:

PARTS: [e-mail]

SERVICE: [e-mail]

2

SAFETY PRECAUTIONS

• Make sure that the oil extractor is in perfect condition before use
i.e. No cracks which would result in oil leaks.

• When disposing of oil, it must be disposed of according to local
regulations. Never pour it down drains.

• When draining oil, make sure that the engine is switched off.

• Warm oil is easier to drain, but make sure the oil is not hot

• Make sure that the oil extractor is on a stable surface.

• If oil is spilt, the area must be cleaned completely and sand or
sawdust scattered on the area to absorb the oil and then cleaned
up. You should also alert people in the vicinity to the possible
danger of slipping.

• DO NOT use this equipment with petrol or other flammable liquids or
chemicals.

• ALWAYS drain and clean the unit thoroughly after use, and store in a
clean , dry place.

PARTS IDENTIFICATION

Plunger

Hose

Collection
Container

Bung

3

ASSEMBLY

1

1. Slide the bung into the top of
the collection container. Make
sure it is secure.

3

2

2. Take the thinner hose and slide
the thick section through the
hole as shown. Do not slide it all
the way through, about 5-7cm
should be enough.

4

3. Screw the plunger into position
taking care not to over tighten
it.

4. The Oil Drainer is ready for use.

4

USING THE OIL DRAINER

1. Place the hose into the oil sump you wish to drain.

2. Make sure the collection container is positioned lower then the oil sump.

3. Raise the plunger up and down to start syphoning the oil into the

collection container.

JOINING THE HOSES

If you require a longer hose, simply
join the two hoses together as
shown.

5

MAINTENANCE AND CLEANING

• Drain and clean the container after use.

• Do not clean the unit with aggressive detergents or chemicals.

SPECIFICATION

Container Capacity ................................ 1.5 L

HOSE A

Internal Diameter .....................................5 mm

External Diameter .................................... 8 mm

Length ........................................................ 1 m

HOSE B

Internal Diameter .....................................8 mm

External Diameter .................................... 10 mm

Length ........................................................ 1.3 m

6

ADDITIONAL INFORMATION

Below are further Clarke products ideal for fluid/oil extraction, available from
your local Clarke dealer.

Clarke CHT588 (Pneumatic Fluid Extractor)

Safely extracts oils, coolents and other fluids from

cars, motorcycles, vans/lorries etc.

Part number: 1801588

Clarke COD70 (70 litre oil drainer)

Gravity fed with 2m discharge

hose, ideal for professional

garage use.

Part number: 7630203

ClarkeOCD8 (8 gallon Oil Drain Cart)

Low entry cart for garage use, ideal for

commercial vehicle oil changes etc.

Part number: 3051470

7