Clare Controls CM-BT10-RX70 User Manual

Doc ID 2013-12-351 • Rev 01

HDBaseT Receiver 70m
User Guide

Model CM-BT10-RX70

Copyright

© 18DEC13 Clare Controls, Inc. All rights reserved.
This document may not be copied in whole or in part or otherwise

reproduced without prior written consent from Clare Controls, Inc.,
except where specifically permitted under US and international
copyright law.

Trademarks and

patents

HDBaseT Receiver 70m, Model CM-BT10-RX70 name is a
trademark of Clare Controls, Inc.

Other trade names used in this document may be trademarks or
registered trademarks of the manufacturers or vendors of the
respective products.

Manufacturer

Clare Controls, Inc., 7519 Pennsylvania Ave., Suite 104, Sarasota,
FL 34243, USA

Version

This document applies to HDBaseT Receiver 70m User Guide,
Model CM-BT10-RX70 version 1.

Contact information

For contact information, see www.clarecontrols.com.

HDBaseT Receiver 70m User Guide i

Content

Limitation of liability...ii!
Introduction...1!

Features...1!
Package contents...1!

Product appearance...2!
System connection...3!

Usage precautions...3!
Application examples...3!
Connection procedure...5!
Application...5!
Twisted pair cable connection...6!

Specifications...7!
Panel drawings...8!
Troubleshooting and maintenance...9!
Safety operation...10!
After-sales service...11!

ii HDBaseT Receiver 70m User Guide

Limitation of liability

To the maximum extent permitted by applicable law, in no event will Clare
Controls, Inc. be liable for any lost profits or business opportunities, loss of use,
business interruption, loss of data, or any other indirect, special, incidental, or
consequential damages unde r any theory of liability, w hether based in co n tr a c t,
tort, negligence, product lia bility, or otherwise. Becau s e s o me jurisdictions do not
allow the exclusion or limitation of liability for consequential or incidental damages
the preceding limitation may not apply to you. In any event the total liability of
Clare Controls, Inc. shall not exceed the purchase price of the product. The
foregoing limitation w ill apply to the maximum extent permitted by applicable la w,
regardless of whether Clare Controls, Inc. has been advised of the possibility of
such damages and regardless of whether any remedy fails of its essential
purpose.

Installation in accordanc e w ith this manual, applicab le c o d e s , a n d th e in s tr u ctions
of the authority having jurisdiction is mandatory.

While every precaution has been taken during the preparation of this manual to
ensure the accuracy of its contents, Clare Controls, Inc. assumes no responsibility
for errors or omissions.

HDBaseT Receiver 70m User Guide 1

Introduction

The CM-BT10-RX70 HDBaseT receiver is designed to work in conjunction with the
CM-BT10-TX70 HDBaseT transmitter or an HDBaseT matrix switch, such as the
CM-MT4410-BT-70. HDMI signals are input into the transmitter or switch, and
HDBaseT technology is used to transmit the signals to the receiver up to 230 ft. (70 m)
via a Cat5e/Cat6 cable. The receiver then outputs the HDMI signal.

Bi-directional IR and RS232 are also transmitted across the Cat5e/Cat6 cable. The
receiver supports CEC, bi-directional RS232 and IR control, and PoC (Power over
Cable), which can be used to power th e r e c e iv e r v ia the Cat5e/Cat6 cable . T h is
eliminates the need for power at the receiver end.

Features

• Supports full HD: Delivers high-resolution image (1080p at 60 Hz, 3D, 4K*2K)

• Maximum transmission dis ta n c e is 230 ft. (70 m) over single a CAT5e/CAT6 cable

• High bandwidth: 10.2 Gbps

• HDTV compatible: Uses HDMI 1.4 and is HDCP-compliant

• Support PoC and CEC

• Communicates with the display to transmit EDID and Hot Plug Detect (HPD)

signals constantly via the CAT5e/Cat6 cable

• Uses HDBaseT technology for extended capability and reliability

• Bi-directional RS232/IR control

• LED indicators show working status to aid in troubleshooting

• Wall or table mount aluminum enclosure

• External power supply (100~240 VAC, 50/60 Hz)

Package contents

• 1 x CM-BT10-RX70 HDbaseT receiver

• 2 x detachable mounting ears

• 4 x screws

• 1 x IR emitter

• 1 x RS232 cables (DB9 female to 3-pin connector)

• 1 x user manual

• 1 x warning sheet

Note: Ensure all the accessories are included. If not, contact your dealer.