Clare Controls amp.1640 User Manual
2014-12-359 • Rev 04
amp.1640 User Guide
16 channel premium amplifier
2014-12-359 • Rev 04
Copyright
© 04DEC14 Clare Controls, Inc. All rights reserved.
This document may not be copied in whole or in part or otherwise
reproduced without prior written consent from Clare Controls, Inc.,
except where specifically permitted under U.S. and international
copyright law.
Trademarks
The amp.1640 name is a trademark of Clare Controls, Inc.
Manufacturer
Clare Controls, Inc.
7519 Pennsylvania Ave., Suite 104, Sarasota, FL 34243, USA
Version
This document applies to amp.1640 version 01.
Compliance
FCC compliance
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
EU compliance
2002/96/EC (WEEE directive): Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see:
www.recyclethis.info.
Contact information
For contact information, see www.clarecontrols.com.
amp.1640 User Guide i
Content
Important information...ii!
Limited three-year warranty...ii!
Limitation of liability...iii!
Important safety instructions...iv!
Welcome to amp.1640...1!
Features...1!
Rear panel features...3!
Rack mounting the amp.1640 amplifier...4!
Installation – getting connected...5!
Installation – setup and options...6!
Global switches...8!
Operations...8!
Troubleshooting...9!
Specifications...10!
amp.1640 User Guide ii
Important information
Limited three-year warranty
Clare Controls, Inc. warrants to the original retail purchaser only that this product
will be free from defects in materials and workmanship for a period of three
years, which starts from the first day you purchase this product, provided the
product was purchased from a Clare Controls Authorized Dealer.
If, during the warranty period, the unit cannot be repaired, a suitable replacement
will be issued. Replacement units will be comparable to the original. However,
due to potential design changes over time, replacement units may not be
identical to the unit replaced.
A valid invoice of purchase via an authorized dealer shall be required for any
warranty coverage.
Items not covered by this warranty
• Damage caused due to incorrect usage and/or connections.
• Damage caused due to installation by person(s) not adequately trained in the
installation of this equipment.
• Any attempt to open this unit and access internal components shall
immediately void this warranty.
• Damage caused by any physical force (dropping the unit or dropping an
object upon the unit, etc.).
• Damage caused by voltage or cycle fluctuations outside acceptable range.
• Damage caused by over-current, voltage spikes, or lightning damage due to
inadequate surge protection.
You can contact Customer Support at http://support.clarecontrols.com. Please be
ready to provide the following information.
• Product model number, version, and serial number.
• Detailed description of the trouble issues.
• Description of all connections and third-party equipment being used.
amp.1640 User Guide iii
Limitation of liability
To the maximum extent permitted by applicable law, in no event will Clare
Controls, Inc. be liable for any lost profits or business opportunities, loss of use,
business interruption, loss of data, or any other indirect, special, incidental, or
consequential damages under any theory of liability, whether based in contract,
tort, negligence, product liability, or otherwise. Because some jurisdictions do not
allow the exclusion or limitation of liability for consequential or incidental
damages the preceding limitation may not apply to you. In any event the total
liability of Clare Controls, Inc. shall not exceed the purchase price of the product.
The foregoing limitation will apply to the maximum extent permitted by applicable
law, regardless of whether Clare Controls, Inc. has been advised of the
possibility of such damages and regardless of whether any remedy fails of its
essential purpose.
While every precaution has been taken during the preparation of this manual to
ensure the accuracy of its contents, Clare Controls, Inc. assumes no
responsibility for errors or omissions.
amp.1640 User Guide iv
Important safety instructions
WARNING: To reduce the risk of fire or electric shock, do not expose this
apparatus in or near rain or moisture.
Caution: To reduce the risk of electrical shock, do not remove cover. No
user serviceable parts inside. Refer servicing to qualified service
personnel.
1. Read the following instructions carefully.
2. Keep manual for future reference.
3. Heed all warnings.
4. Follow all instructions in this manual.
5. Do not expose the apparatus to dripping or splashing and that no objects
filled with liquids, such as vases, shall be placed on the apparatus.
6. Do not use this apparatus near water.
7. Clean only with a dry cloth.
8. Do not block any ventilation openings. Install according to manufacturer’s
instructions.
9. Do not install near any heat sources such as radiators, heat registers, stoves
or other apparatus that produce heat.
10. Do not override the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades - one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade or the third
prong is provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
11. Protect the power cord from being walked on or pinched particularly at plug,
convenience receptacles, and the point where it exits from the apparatus.
12. Only use attachments/accessories specified by the manufacturer.
13. Unplug this apparatus during lightning storms or when unused for long
periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when
the apparatus has been damaged in any way, such as when the powersupply cord or plug is damaged, liquid has been spilled, or objects have fallen
into the apparatus, the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
Loading...