OPERATING INSTRUCTIONS
TECHNICAL DATA
TURBO-SHARP
Power Consumption 710 W
Voltage 120 V
Amps 6.4 A
No Load Speed
Grinder Weight 4.1 lb (1860g)
Shipping Weight 10.1 lb (4581g)
DECLARATION OF CONFORMITY
We declare that we are solely responsible for this product meeting the
following standards and directives: EN 50144:1998, EN 50144-1/A1:2002,
EN 50144-2-3:1998 EN 55014:1993, EN 61000-3-2:1995, 61000-3-3:1995 in
accordance with directive 89/392/EWG, 73/23/EWG and 89/336/EWG1998
Form 6000
December, 2016
CK Worldwide, Inc.
P.O. Box 1636 Auburn, WA 98071 USA
Ph: (253) 854-5820
Fax: (253) 939-1746
®
X
34000 RPM
1
x
1. Grinder Housing :
Multi-functional Cover
Grinder Head
Opening Slide
Scale to adjust the grinding angle
Tungsten Electrode
CK Worldwide, Inc.
5. Angle Iron :
• The angle iron can be mounted so that the machine
- can be fastened in a vice
- can be fastened by means
of a screw clamp
Angle Iron
2. Motor unit :
Rotation-direction indicator
Sleeve
Spindle
Collet Nut
Grinding Disc
Nut and Pin
to hold Wheel
Changes :
Text, illustrations and data correspond with the state of
technology at the time of printing. We reserve the right
to make changes that will further the development of our
product.
Central screw to adjust electrode diameter and angle
On/off Switch
with Lock
3. Power On/Off :
Power on : Push the on/off
switch back. Press the front
of the switch to lock it in
position.
Electrical Connection :
Connect only to single-phase alternating current and only to the
voltage stated on the specication label. The TURBO-SHARP®X
is insulated according to DIN 57 740/ VDE 0740 (EEC 20) and
can be connected to ungrounded electrical sockets. Radio
interference complies with European Norm EN 55014.
Power off: Press the back
of the on/off switch. The
switch will automatically
return in the off position.
6. Optional Grinding Head :
• A second head (colored red) is available for the
TURBO-SHARP®X for electrodes with diameters of
.040“(1.0mm) - 5/32“(4.0mm) - 3/16“(4.8mm) - 1/4“(6.4mm)
ORDER NUMBER: TS3-HR
7. How to Use :
• Make adjustments for the angle of the point (in degrees)
and the electrode diameter;
- Loosen the central screw on the head
- Set the degree and the electrode
diameter by turning the grinder head
- Tighten the central screw
The number of degrees equals the angle
of the point on the sharpened electrode
• Turn on the TURBO-SHARP
®
X
• Guide the tungsten electrode through the opening that
coincides with its diameter
• Carefully press the tungsten electrode onto the revolving
disc, while at the same time rotating it with light pressure
(the harder the tungsten is pressed against the disc, the
shorter the lifespan of the disc is)
• Continue to rotate the electrode as it is removed from the
disc until there is no longer any contact
• Inspect the results and, if necessary, repeat the process
4. Vacuum Removal of Dust :
• Loosen and then completely remove the three hexagonal
countersunk screws with a 4mm hexagonal key
• Remove the cover
• Use the supplied
rotating socket and connect
to the vacuum system.
We recommend this procedure as a safety measure to
minimize contact with tungsten dust that results from
the grinding process.
Cover
Screws
• The multi-functional cover with integrated opening slide
makes it possible to surface grind electrodes that have
welding deposits due to the welding process. In addition,
ground electrodes can be given a truncated cone.
8. Grinding Disc Adjustment :
• To obtain a different grinding area on the disc, loosen
the 3 set screws on the base of the head-cover and
rotate the collar to 1,2 or 3. This will allow 3 different
grinding locations on the disc for one particular angle.
Warning ! Do not sharpen bent or burnt electrodes.
Remove any drops on the point
sharpened. Use the electrode holder for short electrodes.
of the electrode before it is
2
CK Worldwide, Inc.
CHANGING THE GRINDING WHEEL
Remove the plug from the electrical socket before doing any maintenance on this machine !
• Locate and remove the three small set screws in grinder housing
• Remove grinder housing exposing wheel and shaft assembly
• Place wrench #17 on the collet nut
• Place wrench #10 on the wheel retaining nut
• Remove wheel retaining nut - NUT HAS LEFT-HAND THREADS
• Remove washer and grinding wheel
• Install new grinding wheel
• Replace washer and wheel retaining nut
• Tighten wheel retaining nut
• Make sure wheel is level
• Replace grinder housing (Don‘t force, gently slide housing on
to ensure an easy installation)
Very important !!!
Ensure that the wheel is properly
mounted and not crooked.
Spindle
Collet
Collet Nut
Wheel take-off Shaft
Grinding Wheel
Washer
Wheel Retaining Nut
(LEFT-HAND THREADS)
CHANGING THE TAKE-OFF SHAFT & COLLET
Remove the plug from the electrical socket before doing any maintenance on this machine !
• Position wrench #15 on the spindle
• Position wrench #17 on the collet nut
• Loosen the nut
• Replace the wheel take-off shaft
• Tighten the nut
Follow the same
procedure to change
the collet, except
collet nut must be completely
unscrewed in order for the collet to be changed.
These procedures must be followed exactly as they are explained
and illustrated.
3
CK Worldwide, Inc.
SAFETY INSTRUCTIONS
• Observe the safety guidelines in this manual! Do not drill
through the safety cover of the machine, as it will then no
longer be insulated.
• Remove the plug from the electrical socket before doing any
work on the machine.
• Insert the plug into an electrical socket only if the machine is
turned off.
• Keep the cord away from the area where you are working. Run
the cord away from the back of the machine.
• Check the equipment, cord, extension lead and electrical plug
for damage and signs of wear before each use. Damaged parts
should be replaced by an expert.
• Follow the accident-prevention regulations of your professional
association.
• Do not reach into the danger zone of machinery that is turned
on.
• Always wear safety goggles.
• Only use tools with an rpm at least as high as the highest idle
rpm of the machine.
• Inspect the grinding wheel before use. The wheel must be per-
fectly mounted in order to turn freely. Test the wheel for at least
30 seconds before use. Do not use wheels that are damaged,
asymmetrical, or that vibrate.
• Tighten the wheel retaining nut before each use of the machine.
• Noise level values: Typically around GS 400=79db (A). Noise
levels can be higher than 85 dB (A) when in use. Wear
hearing protection.
• Vibration values: the effective speed is typically around GS 400
= 9m/s
2
USEFUL TIPS
The best results will be obtained by applying light pressure to the
electrode while at the same time rotating it on the disc. Remove
the electrode before turning off the grinder.
Using too much pressure while grinding will damage the grinder
and require more grinding discs; performance will suffer.
Warning :
Always keep the air-intake vents clean.
Accessories :
Only use CK accessories and spare parts.
Spare parts :
Grinding wheel TS3-W
Standard Head TS3-HB
Optional Head TS3-HR
WARRANTY
In addition to the dealer’s sales contract warranty, the customer will receive a warranty
according to the following conditions:
1. The warranty covers 24 months, dating form delivery of the product. Delivery
must be substantiated by an invoice or other documentation.
2. CK Worldwide, Inc. warrants the TURBO-SHARP®X to be free of defects in
materials and workmanship. CK limits this warranty to replacement of the product
or parts thereof, and excludes liability for injury, property damage, or economic
loss attributable to product use or misuse. Warranty claims must be made within
the specied products valid warranty period.
3. In situations covered by the warranty, we ask that the product be returned,
together with the appropriate warranty documentation to the vendor. Please
provide a brief description of the problem.
4. Repairs that are covered by the warranty will not be charged to the customer.
The warranty will not be extended or affected by the repairs. Parts that have
been replaced become the property of CK.
4
Loading...