C&K AG6 User guide

INSTALLATION

INTRUCTIONS

AA

G6G6

A

G6

AA

G6G6

EXTERN EXTERN

EXTERN

EXTERN EXTERN

Downloaded from: http://www.guardianalarms.net

AL SOUNDER & STRAL SOUNDER & STR

AL SOUNDER & STR

AL SOUNDER & STRAL SOUNDER & STR

OBEOBE

OBE

OBEOBE

WARNINGS

STROBE CIRCUITS CARRY HIGH VOLT AGES (350 volts.) AL W AYS make sure the unit
has been disconnected from all external power for at least 5 minutes before removing

ANY safety cover.
WEAR hearing protection when close to a sounder.
ALWA YS observe safety precautions with regard to ladder use.

Plastic bags can suffocate - always dispose of carefully.
NEVER put screwdrivers or other sharp objects in pockets - ALWAYS use a tool belt.

STST

ANDAND

ST

AND

STST

ANDAND

This unit has been tested to the required standards for emission, immunity as set out by
the EEC (ECD 89/336/EEC). This unit complies with EN50131-1 which relates to security
control equipment.

STST

ANDAND

ST

AND

STST

ANDAND

1 x AG6 sounder .
1 x Accessory bag containing: - 4 x No 8 Wallplugs, 4 x 2” No 8 screws, Lid screw , screw cap.

This instruction manual Part No

F-051-599-00.

ARD PARD P

ARD P

ARD PARD P

ARDSARDS

ARDS

ARDSARDS

ARAR

TS LISTTS LIST

AR

TS LIST

ARAR

TS LISTTS LIST

INSTINST

INST

INSTINST

Here is a brief description of a typical setup and installation procedure for the AG6.

1. Mount the unit to the desired surface.

2. Connect the AG6 to the control panel.

3. Connect BA TT link.

4. Replace covers and tighten the tamper screw .

5. Power up the control panel.

AG 6

SECU RIT 800 Se ries R- V- ST- V+ S-

SECU RIT 7 0 3 R- 0V

SECURIT 7 0 0L R- BEL L- ST- BEL L+ S-

BRAVO 700 R- BELL- ST- BELL+ S-

ACTIVE 5X 21

ACTI VE 4 13

724 / 764 TAMP RET V- IN T BELL- AUX+ EXT BELL-

ARIT ECH CS3 50 17 1 6 7 4 5

VERI FI ER 6 TAMP R ET -VE HOLD - INT B EL L + EXT BELL - EXT B EL L

ADE TRO SCB- STR BEL L+ BEL L-

ME NVI ER BE L L TAMP 0V ST B BE LL 12 V BE LL TR IG

OPTI M A X L 4 A T STRO BE- D B

TEXE CO M C D S A B

SCAN TRO NIC TR 0V ST R NO- 1 2V+ BEL L NO­PARAG ON P L US BT B- STB- B+ BA
CHAL LENGER 5 C A ST- D B

Negative Tam per ReturnV-Negative Supply

ALLAALLA

ALLA

ALLAALLA

R-

(NO T E 2 )

(NO T E 2 )

TION OTION O

TION O

TION OTION O

CONNECTIONSCONNECTIONS

CONNECTIONS

CONNECTIONSCONNECTIONS

(NO T E 1 )

20

(NO T E 3 )

12

(NO T E 3 )

2

VERVER

VER

VERVER

ST-

Ne gativ e Stro be Trig gerV+Positive Supply

ST- BEL L+ NO

ST- BEL L+ S­ST- BEL L+ S-

VIEWVIEW

VIEW

VIEWVIEW

Negative Sounder Trigger

-SW

NOTES FOR TERMINAL CONNECTIONS.

1) Link the terminal marked COM to 0V terminal at the panel.

2) This should be wired in series with all other tampers and then connected to the pin shown.

3) This connection should be the start of the tamper loop and is also used as HOLD OFF
negative.
When connecting the bell box to a control panel designed for use in Eire ( Ireland ) for
example the Verifier 6 or Aritech, a diode should be installed as shown below. For panels
without a strobe output, Link the ST- to the SW- .

TECHNICAL INFORMATECHNICAL INFORMA

TECHNICAL INFORMA

TECHNICAL INFORMATECHNICAL INFORMA

HOLD OFF SUPPL Y 13.65Vdc nominal 12.0 to 14.5Vdc.
LOAD CURRENT 35mA nom. Quiescent.

260mA nom. Combined sounder and strobe.
125 mA nom. Strobe only.

SOUND OUTPUT LEVEL 1 10dB @ 1m nom (Supply & Mounting Dependant)
BA TTERY 6.0v, 280mAhr Nicad. Automatic charging from hold of f

supply. Design life = 5 years at 20°C nom. Minimum of 3
15 minute alarms from fully charged battery without
recharge.

TEMPERATURE RANGE -20°C to +40°C. Operating & Storage
TRIGGER CONDITIONS Automatic reset occurs when trigger clears
HOLD OFF Loss of hold off supply

S- Negative Trigger (-V applied)

Trigger occurs when terminal voltage is less than 3.5v.
Maximum load 1.0mA

TIONTION

TION

TIONTION

TAMPER DETECTION Wall & Cover retaining screw
TAMPER OUT Normally closed negative tamper return

CUT OFF TIMER 15 minutes nom. (Sounder Only).
STROBE TRIGGER -V applied

STROBE 0.6 Joules per flash. 1 flash per second nom. @ 13.65Vdc.
DIMENSIONS H 55mm W 200mm D 300mm
WEIGHT Gross 840 grams

3

MOMO

MO

MOMO

If you are fitting the unit horizontally, you can rotate the AG6 so that the strobe is either to
the left or right. However, this would mean in certain cases the tamper screw would be
awkward or in the wrong position to tighten. To remove this potential problem, the tamper
switch can simply be unclipped from its mounting pins and moved to the opposite side of
the base. Make sure the tamper switch is secure before mounting the base.

NOTE:
For correct operation make sure the BATTERY LINK is fitted.

The TAMPER switch must be closed for the AG6 to get any power from the control panel. This
will also power the LED.

NACOSS Regulations.

This unit will conform to NACOSS regulations when installed correctly: In the event that the
bell box tamper is opened, this unit will send a tamper signal to the control panel and trigger
a local sounder when the system is unarmed .

VING VING

VING

VING VING

THE THE

THE

THE THE

TT

AMPER SWITAMPER SWIT

T

AMPER SWIT

TT

AMPER SWITAMPER SWIT

CHCH

CH

CHCH

This product is manufactured to ISO 9001 quality assurance and complies with all relevant
standards as set out for EMC. This product is Year 2000 compliant.

CERTIFIED
COMPANY

HKQA A

Please Note:

C&K SYSTEMS are always endeavouring to improve quality and specification of all it’s
products and may alter or amend this product and instructions without notice. All information
is given in good faith but without warranty.

C & K Systems

REDDITCH.
WORCESTERSHIRE
ENGLAND
Tel: [phone]
Fax: [phone]
T echnical Helpline: 0345 660533 UK Only .
Website: http://users.powernet.co.uk/cksys
E-mail: [e-mail]

Certificate No CC106

Printed & Manufactured in Republic of China by C&K Systems. Document No F-051-599-00

4