Citronix CI5000SERIE Users Manual

(Draft copy of)

Citronix ci5000 Series Printer

Operation Guide

ci5200

ci5300

ci5500

ci5650

Revision 1.0

Part Number:

012-xxxx-xxx

ci5000 Series Printer Operation Guide

THIS PAGE INTENTIONALLY LEFT BLANK.

Draft Version 0.1 2

ci5000 Series Printer Operation Guide

CITRONIX ci5000 Series PRINTER OPERATION GUIDE

This guide, Citronix Part No. 12-xxxx-xxx, is used in basic operation of ci5000 Series Continuous Ink
printers.

Users of this printer are warned that it is essential to read, understand and act according to the
information given in Part 1: Health and Safety. This part of the manual also specifies a set of symbols
which are used elsewhere in the manual to convey special warnings or requirements. It is essential
that users are familiar with these symbols and act accordingly.

All rights reserved. No part of this publication may be reproduced, stored on a retrieval system, or
transmitted in any form, or by any means, electronic, mechanical, photocopying, recording or otherwise,
without the prior permission of Citronix Inc.

To the best of our knowledge, the information contained in this guide was correct at the time of printing.
Continual enhancement of our products may result in some differences between instructions represented
in this guide and your ci5000 Series Printer.

Citronix and Codes of Excellence are trademarks of Citronix Inc.

This guide was written by:

Citronix Inc.

2241 S. Watson Road
Arlington, Texas 76010
United States of America

www.citronix.com
[e-mail]

© Copyright Citronix Inc. 2003 – 2016

, Suite 111

Draft Version 0.1 3

ci5000 Series Printer Operation Guide

DECLARATION of CONFORMITY

Issuer’s name: Citronix Inc.

Issuer’s Address: 2241 S. Watson Road, Suite 111, Arlington, Texas 76010, United States of America

Tel: [phone] Fax: [phone] Email: [e-mail]

Declare under sole responsibility that the products identified herein, have been designed, manufactured
and tested in accordance with the following documents:

EN55024:2010 Information Technology Equipment – Immunity Characteristics – Limits

and Methods of Measurement.

EN55022:2010 Information Technology Equipment – Radio Disturbance Characteristics

– Limits and Methods of Measurement.

EN61000-6-2:2005 Electromagnetic compatibility (EMC) - Part6-2: Generic standards –

Immunity for Industrial Environments

EN60950-1:2006/A2:2013 Information Technology Equipment - Safety - Part 1: General

Requirements.
2014/35/EU Low Voltage Directive
2014/30/EU EMC Directive

CE-Marked accordingly certification date ____ 2016

Each product marketed, is identical to the representative unit tested and found to meet the standards.

Trade Name: Citronix
Type of Product: Continuous Ink Jet Printer
Model: ci5200, ci5300, ci5500, ci5650

Signed for and on behalf of

Citronix Inc.
2241 S. Watson Road, Suite 111
Arlington, Texas 76010

____________________

Michael Embree
Engineering Director

Draft Version 0.1 4

ci5000 Series Printer Operation Guide

FCC Notice

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.

Any changes or modifications not expressly approved by the manufacturer could void the user's authority
to operate the equipment.

FCC/Industry Canada Statement

This device complies with FCC Part 15 and Industry Canada license exempt RSS standard(s). Operation
is subject to the following two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired operation of the device.

This device complies with Health Canada’s Safety Code. The installer of this device should ensure that
RF radiation is not emitted in excess of the Health Canada’s requirement.

Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.

French Version:

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts
de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire
de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement

Cet appareil est conforme avec Santé Canada Code de sécurité 6. Le programme d’installation de cet
appareil doit s’assurer que les rayonnements RF n’est pas émis au-delà de I’exigence de Santé Canada.

Les changements ou modifications non expressément approuvés par la partie responsable de la
conformité pourraient annuler l'autorité de l'utilisateur à utiliser cet équipement.

European EMC Statement

This product may cause interference if used in residential areas. Such use must be avoided unless the
user takes special measures to reduce electromagnetic emissions to prevent interference to the
reception of radio and television broadcasts.

Draft Version 0.1 5

ci5000 Series Printer Operation Guide

CONTENT

PART 1 : GENERAL INFORMATION

PART 2 : DESCRIPTION

PART 3 : PRINTER OPERATION

PART 4 : DISPLAY MESSAGES AND FAULT FINDING

PART 5 : REFERENCE

Draft Version 0.1 6

ci5000 Series Printer Operation Guide

PART 1 : GENERAL INFORMATION

CONTENTS

INTRODUCTION ................................................................................................................... 1-2

Where to find more information: ..................................................................................................... 1-2

Before You Begin: .......................................................................................................................... 1-2

Page

SAFETY INFORMATION ...................................................................................................... 1-2

Specific WARNINGS ...................................................................................................................... 1-3

Draft Version 0.1 1-1

ci5000 Series Printer Operation Guide

INTRODUCTION

Welcome to the ci5000 Series Continuous Ink Jet Printer.

The Citronix ci5000 Series Continuous Ink Jet Printer applies identifying marks such as “best before”
dates, traceability codes, logos and batch codes onto almost any kind of material or surface.

This guide can be used for all ci5000 Series Printers, namely ci5200, ci5300, ci5500 and ci5650 as
well as specialty Printers (micro, HS50, Pigment and Heavy Pigment). Any differences between
product variants are identified or highlighted.

Citronix CIJ printers are comprised of Hardware, Software, and the fluids for cleaning / printing.

Where to find more information:

Refer to the ci5000 Series Technical Service Manual for comprehensive detail on installation,
configuration, service, troubleshooting and component replacement.

Before You Begin:

Before printing, make sure:

1. All warnings and notes have been read and understood.

2. The ci5000 Series Printer is correctly installed and integrated with your production line.

3. At least one message has been created, programmed and saved (refer to Section X) or select the
default message.

SAFETY INFORMATION

The following symbols are used in this manual. Where they appear next to a procedure or instruction,
they have the significance and importance of written warnings and cautions. WARNINGS, CAUTIONS
and NOTES are provided to avoid hazards and to safely operate the Printer.

A WARNING symbol identifies an operating procedure that if not strictly followed could
result in injury or death. Warnings will be identified by a general warning symbol or a
specific warning symbol.

A CAUTION symbol identifies an operating procedure that if not strictly followed could
result in equipment damage.

A NOTE symbol indicates an operating procedure that is essential but not known to cause
hazards as indicated by a Warning or Caution symbol.

Draft Version 0.1 1-2