Citiwell 89391, 89389 User Manual
MAINTENANCE
Do not fly with damaged blades. Please change the blades. To do so gently unscrew the
damaged blade using a small + screwdriver, replace and retighten the screws. Ensure to
use the correct replacement blade.
Additional Replacement blades can be purchased at www.eyespytoys.com or by calling
1866 469 9686.
TROUBLE-SHOOTING
If at any time the Eagle Spy, or viewer stop working or work in an unexpected
fashion:
1. Check the condition of the batteries, replace the alkaline batteries in the remote
controller and charge the helicopter and viewer.
2. Turn both units off for 15 seconds and then turn them both back on. This will reset the
electronic systems.
For any other problems or concerns,
www.eyespytoys.com or call our Customer Assistance Line at 1866 469 9686
© 2012 EyeSpy TM is a registered trademark of EyeSpy Toys Ltd. All rights reserved.
Manufactured for and distributed by Citiwell International Inc.
Conforms to the safety Requirements of CPSIA, ASTM F963 and EN-71(1).
WARNING! . Not suitable for children under 3 years of age due to small parts.
In an effort to continually improve our products, the items inside this package may vary slightly
from the photographs
9-401 Magnetic Drive, Toronto,Canada, M3J 3H9
Customer Care:1866 469 9686
please contact us
via the EyeSpy website
12+12+
MADE IN CHINA
PRINTED IN CHINA
www.eyespytoys.com
Contains LiPo battery pack. • Battery pack must be recycled or disposed of properly. • If at any time in
the future you should need to dispose of this product please note that Waste Electrical Products should
NOT be disposed of with household waste. Please recycle where facilities exist. Check with your Local
Authority or retailer for recycling advice. (Waste Electrical and Electronic Equipment Directive).
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
EaGlESPy
surveillance technology
INSTRUCTION GUIDE
www.eyespytoys.com
The EyeSpy™ EAGLE SPY is an amazing radio-controlled,
camera-equipped helicopter enabling you to see the world just as if
you were sitting in the cockpit!
CONTENTS LIST AND PARTS IDENTIFICATION
Rotor Blade
Stabilizer
Antenna
Add SD Card
To record a movie, press the Select button (check mark). The red dot in the upper right
corner of the screen will begin to flash on and off and a timer will appear that shows the
duration of the movie. To stop the recording, press the Back button (up-arrow).
You can also instantly start a recording by pressing the large round button on top of the
camera.
Tail
Rotor
Rotor Blade
Landing Skid
AC Adapter
Rotor Blade
GETTING STARTED
Controller:
1.
Use a small Philips head (+) screwdriver to remove
the battery compartment cover located on the back
of the controller. Insert six AA 1.5V alkaline batteries, taking care to insert them correctly, using the
images molded into the plastic of each battery
location. Reinsert the battery cover and retighten the
two chromed screws. Do not use inexpensive
carbon-zinc batteries, generally labeled “heavyduty.”
BATTERY SAFETY INFORMATION
• This unit uses six AA 1.5V batteries. Always use fresh batteries.
• Do not mix old and new batteries. Do not mix batteries of different types.
• Remove exhausted batteries and dispose of them properly.
• If this item will not be used for an extended term please remove the batteries.
• Do not try to recharge a non-rechargeable battery.
• Do not take a battery apart. Do not short-circuit the terminals.
• Do not dispose of batteries in fire – they may explode.
Camera
Viewer
USB Cable
Controller
Add
Batteries
REVIEW – When you choose this screen option and press the check mark button, you will
be given the choice of reviewing any photos or movies you have taken. The SD memory
card containing the photos or movies must be inserted in the viewer to use this function.
Once you choose to review either photos or movies you will be shown a list of the items
stored on the SD memory card. Move the cursor with the down-arrow button. Press the
check mark button to choose which item you wish to review. Press the up-arrow button to
return to the item choice menu. Press the up-arrow again to return to the main screen menu.
TIMER – Use the Next button (down-arrow) to choose the timer function, then press the
Select button (check-mark). A timer display is shown and you are given the choice of adding
time or confirming your choice (OK). The timer display will increase by one minute every
time you choose to “Add Time”, up to a maximum of 5 minutes. If you continue pushing the
Select button the timer display will return to “00:01” (one minute). Choosing “OK” will start
the countdown to “00:00.” Movie recording will then start, and will continue for 90 seconds.
The timer will then begin the countdown again, using the preselected time. Another 90
second movie will be recorded. This will continue until the user-installed SD memory card is
full. The number of movies you can record and save will depend on the memory capacity of
the SD card you are using.
DELETE – Choosing this function and pressing the check-mark button lets you delete any
photo or movie by choosing it and then pressing the check-mark button. You will be asked
to confirm your choice by pressing the check-mark button again. Choices are also available
to delete all photos or all movies at once.
VIEWER BATTERY RECHARGING
Some function screens will show a battery icon in the upper left hand corner of the screen.
As battery power is used the bars that make up the battery icon will disappear one by one.
When the lithium-polymer battery needs to be recharged a “Battery Low” icon will briefly
appear and the battery icon will turn red and flash on and off several times.
Attach the USB cord and connect the viewer to a computer’s USB port as described in the
above section “GETTING STARTED.”
1. 6.
Loading...