Cissell WE181 Installation Manual

2

Part No. D0148

23456789012345678901

IPSO - LSG n.v.

Instruction manual

WE181

With electronical timer µ20

Technische gegevens

Technical specifications

Installation instructions

Gebruiksaanwijzing

Operating instructions

Nieuwstraat 146 - B-8560 Wevelgem (Belgium)

Tel. 056/41 20 54 - Fax 056/41 86 74

Installatie

Maintenance

Onderhoud

Contents

1 General safety instructions .............................................................. 3

2 Technical data and dimensions ....................................................... 4

Technical data ................................................................................ 4

Dimensions ..................................................................................... 5

3 Installation and connection ............................................................. 6

Ground ............................................................................................ 6

Anchoring ....................................................................................... 6

Water connection ............................................................................ 6

Water drain ..................................................................................... 7

Main power connection .................................................................... 7

Liquid soap connection ................................................................... 8

Connection of a central operating panel for coinmachines ............... 9

Steam connection ........................................................................... 10

4 Operating instructions ..................................................................... 11

Machine with start button ................................................................ 12

Machine with coin or token operation............................................... 20

5 Standard programs .......................................................................... 26

6 Technical remarks ............................................................................ 27

Internal connection of the electrical heating .................................... 27

Internal connections of the motor .................................................... 27

Thermo-magnetic motor protection .................................................. 28

Error messages .............................................................................. 28

7 Maintenance of the machine ........................................................... 30

Code: 249/00212/01

21/12/00

Content

General safety instructions

Ignoring any of the safety instructions can cause serious personal injury and can also cause damage to the linen or the machine

Read the installation and instruction manual carefully before connecting the

S

machine.

It is recommended that the machine be installed by qualified technicians.

S

The machine should be installed according to the installation instructions.

S

(See chapter 4)

The machine should be grounded according to the instructions in order to

S

eliminate the risk of electrocution.

Do not expose the machine to high humidity or extreme high or low

S

temperatures.

Cut off all main water inlets, steam and electrical supplies at the end of each

S

operating day.

1

Before starting repairs or maintenance, shut off all power and water supplies.

S

To prevent fire and explosion:

S

Keep the area around the machine free from inflammable or combustible products. Do not put fabrics that are treated with inflammable products into the machine. These fabrics should be hand-washed or air-dried first.

Always carefully read and follow the instructions on the packing of deter-

S

gents. Store these products out of the reach of children.

Always take into account the instructions on the labels of clothes.

S

Never allow children to play in the surroundings of a machine.

S

Remark:

These instructions surely cannot prevent all risks of accidents. It is up to the user to act with the

S

utmost precaution.

Do not hesitate to contact the dealer in case of a problem.

S

3

Technical data and dimensions

Technical data

Capacity (dry weight)

1/11 16,4 kg 1/10 18 kg 1/9 20 kg

Cylinder

Diameter 680 mm Depth 500 mm Volume 181 Lit.

Cabinet

Height 1170 mm Width 780 mm Depth 885 mm

Front loading

Diameter door opening 395 mm Door height 400 mm To center 640 mm

Speed

Wash 46 rpm Spin 432 rpm

G-force

Spin 71

Motor(3 phase)

Wash 18p. 290rpm 280 W Spin 2p. 2900 rpm 1300 W

Drain valve

Depend-O-Drain 6/4"

Water supply

Hard, soft, warm water and cool-down 3/4"

Steam connection

Steam connection 3/8"

Heating

Electrical 220/380 V 12/15/18 kW Electrical 380 V 12/15/18/21/24 kW Steam X Warm water (without additional heating) X Warm water (with additional heating) X

Packing dimensions

(H x W x D) 1300x850x1100 mm

Weight

Net 325 kg Gross 377 kg

2

WE 181

4

Dimensions

2

A. Hard water connection 3/4"

S

B. Warm water connection 3/4"

S

C. Soft water connection 3/4"

S

D. Electrical connection

S

E. Electrical connection clamps

S

F. Water drain

S

G. Steam connection

S

H. Ventilation soap dispenser

S

5

Installation and connection

Surface

The machine must be securely fixed on a flat surface (metal base, concrete or solid ground). The anchoring is to be done on the provided places (A) in the base. (See Dimensions 2) The machine must be placed entirely level. For easy maintenance it is recommended to keep a minimal distance of 600 mm between the wall and the back of the machine. If several machines are placed next to each another, there should be a minimal distance of 30 mm between each machine.

Anchoring

On a metal base

3

D

E

F

D

B

C

G

The machines must be fixed on a metal base which is securely anchored on a concrete base.

A: Bolt M16 B: Concrete base 40cm C: Washer 40x17x4 D: Nut M16 E: Base of the machine F: Metal base

A

Directly on the ground

The machine must be anchored directly on a concrete base.

D

E

B

A

C

A: Bolt M16 B: Concrete base 40cm C: Washer 40x17x4 D: Nut M16 E: Base of the machine

Water connection

The machine is delivered with hoses with 3/4" connections. These hoses fit the water inlet valves of the machine and the main water inlet taps. To ensure the optimal functioning of the water inlet valves, the water pressure on the inlet should be between 0,5 and 10 kg/cm² (7 and 145 psi). If the pressure is too low, the cycle time will increase considerably. In case of boiler fed machines, a minimum of 145 l. hot water of 90°C should be available.

6

3

Water drain

Main power connection

The machine is equipped with a drain valve with 6/4" outer diameter (50 mm). This drain valve should be connected to the drain by means of the drain elbow which is delivered with the machine.

The diameter of the main drain should be adapted to the water flow and

S

the number of machines. It should be sufficient to handle at least 160L/ min. per machine.

It is necessary to connect the main drain at least on one side to an open

S

air-brake to allow ventilation.

Remove the cover plate at the back of the machine. (See dimensions (E)).

S

Connect the power cable to the connectors.

S

220V 3AC

220V 3 phase (3AC) should be connected to the connectors “L1,L2,L3”. The green/yellow grounding clamp has to be connected to the grounding wire “PE”.

380 V 3AC + N

380 V 3 phase (3AC + N) has to be connected to the connectors “L1,L2,L3”, the blue neutral to the “N” connector. The green/yellow grounding clamp has to be connected to the grounding wire “PE”.

Power of the breaker plugs:

After connection, check the spin direction. The cylinder must spin in the direction of the arrow, showed on the sticker on the door window

S

(clockwise). A wrong spin direction can damage the motor, and can also cause water to spurt from the soap dispenser.

In case of wrong spin direction: switch the terminal clamps of the motor circuit “R” and “S” of the connecting cable.

S

machine with steam heating or boiler fed machines without additional electrical heating

220V 3AC 380V 3AC + N

16 A 16 A

machine with electrical heating

Heating: 220V 3AC 380V 3AC + N

12 kW 40 A 20 A

15 kW 50 A 25 A

18 kW 50 A 32 A

21 kW ---- 40 A

24 kW ---- 40 A

7

Liquid soap connection (option)

3

Connection of the liquid soap

hoses

Electrical connection of

the liquid soap pumps

A rubber connection has been placed over the air break opening at the back of the machine. There are 5 holes in this rubber connection, through each of which a liquid soap hose can be driven (S1...S5). Press the hoses until they appear well inside the soap dispenser. The central gap in the rubber connection remains and serves as air breaker.

On machines equipped with a liquid soap connection, connect the wires directly on the print board next to the ground wire connection (option). Connect as indicated on the wiring diagram.

The two connectors on the right give a tension of 220V ~ (max. 4A) which can be applied to drive 220V ~ soap pumps. If more than 4A is required, an external tension will have to be used. 6 connections have been provided, of which one (S6) can be used to drive a waterproofing pump (e.g. for rain coats, etc.).

The 220V can be transformed to other values to drive other type soap pumps.

Example: pumps 24V ~.

Also, pumps with different operating tension can be combined.

Example: 5 pumps 220V ~ and 1 pump 24V ~.

With an external tension 24V DC

8

Connection of a central operating panel for coinmachines (option)

At the backside above the main connectors, you find a printboard, to which the central operating panel for coinmachines can be connected. The right connectors form a potential free output contact as a result of which the operating panel detects when the machine is activated or not. The left connectors receive the signal, by means of which a machine is chosen through the operating panel. There are 3 different variations possible according to the output voltage of the operating panel.

3

A

Remark :

If a machine is equipped with this kind of printboard or if a printboard has been built in, the resistance of the cycle contact (A) may no longer

be present on the main printboard. When this resistance is present, it has to be cut out of the main printboard.

9

Cissell WE181 Installation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual