Cissell CUCC Installation Manual

Laundry Presses

Refer to Page 3 for Model Numbers

Operation/Maintenance

SCR526N

Keep These Instructions for Future Reference.

(If this machine changes ownership, this manual must accompany machine.)

An LSG Company 831 South First Street, P.O. Box 32270 Louisville, KY 40232-2270 Phone: (502) 587-1292 Sales Fax: (502) 585-3625 Service/Parts Fax: (502) 681-1275 www.cissellmfg.com

Part No. AJ1027

December 2004

Table of

Contents

Model Identification ........................................................................... 3

Safety Information .............................................................................. 5

Explanation of Safety Messages........................................................... 5

Important Safety Instructions ............................................................... 5

Introduction......................................................................................... 7

Replacement Parts ................................................................................ 7

Nameplate Location.............................................................................. 7

General Description.............................................................................. 7

Optional Equipment.............................................................................. 7

Operation............................................................................................. 9

Operating Controls and Indicators – Typical Laundry Press................ 9

Operating Controls and Indicators – Typical Laundry Collar

and Cuff Press .................................................................................... 11

Pre-Operating Services......................................................................... 13

Press Operation..................................................................................... 15

Presses Without Timers or Presses With Timer Set to

“OFF” Position ............................................................................... 15

Presses With Timers Only ............................................................... 15

Post-Operating Services........................................................................ 15

Maintenance ........................................................................................ 17

Periodic Inspections.............................................................................. 18

Cleaning Press Head............................................................................. 19

Cleaning Air Filter/Regulator............................................................... 19

Cleaning Steam Strainer ....................................................................... 20

Cleaning Customer-Furnished Steam Traps......................................... 20

Cleaning Air Strainer............................................................................ 20

Filter/Lubricator Maintenance.............................................................. 21

For Non-SMC FRL (Air Filter/Regulator/Lubricator) .................... 21

For SMC FRL (Air Filter/Regulator/Lubricator)............................. 21

Lubrication............................................................................................ 21

Adjusting Air Line Lubricator Flow Rate........................................ 21

Filling Air Line Lubricator .............................................................. 21

Quality Troubleshooting....................................................................... 26

means without the expressed written consent of the publisher.

Notes

AJ1027© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

Model Identification

Information in this manual is applicable to these model(s):

LP19 (C218) LP22 (C222) LP51 (C451) LP53 (C554) CUCC (CCCW-ST and CCCW-C)

AJ1027

Notes

AJ1027

Safety Information

Indicates an imminently hazardous situation that, if not avoided, will cause severe personal injury or death.

DANGER

WARNING indicates the presence of a hazard that can cause severe personal injury, death, or substantial property damage if the warning is ignored.

WARNING

CAUTION indicates the presence of a hazard that will or can cause minor personal injury or property damage if the caution is ignored.

CAUTION

Explanation of Safety Messages

Precautionary statements (“DANGER,” “WARNING,” and “CAUTION”), followed by specific instructions, are found in this manual and on machine decals. These precautions are intended for the personal safety of the operator, user, servicer, and those maintaining the machine.

Important Safety Instructions

Save These Instructions

WARNING

To reduce the risk of fire, electric shock, serious injury or death to persons when using your press, follow these basic precautions:

W372

1. Read all instructions before using the press.

2. Refer to the GROUNDING INSTRUCTIONS in the INSTALLATION manual for the proper grounding of the press.

3. Do not allow children to play on or in the press.

4. Do not reach into the press while the press is in operation.

5. Do not install or store the press where it will be exposed to water and/or weather.

6. Do not tamper with the controls.

Additional precautionary statements (“IMPORTANT” and “NOTE”) are followed by specific instructions.

IMPORTANT: The word “IMPORTANT” is used to inform the reader of specific procedures where minor machine damage will occur if the procedure is not followed.

NOTE: The word “NOTE” is used to communicate installation, operation, maintenance or servicing information that is important but not hazard related.

7. Do not repair or replace any part of the press, or attempt any servicing unless specifically recommended in the user-maintenance instructions or in published user-repair instructions that the user understands and has the skills to carry out.

8. To reduce the risk of an electric shock or fire, DO NOT use an extension cord or an adapter to connect the press to the electrical power source.

9. Use press only for its intended purpose, finishing garments.

10. ALWAYS disconnect the press from electrical supply before attempting any service. Disconnect the power cord by grasping the plug, not the cord.

11. Install the press according to the INSTALLATION INSTRUCTIONS. All connections for steam, electrical power and grounding must comply with local codes and be made by licensed personnel when required.

AJ1027

Safety Information

12. Replace worn power cords and/or loose plugs.

13. Never operate the press with any guards and/or panels removed.

14. DO NOT operate the press with missing or broken parts.

15. DO NOT bypass any safety devices.

16. Failure to install, maintain, and/or operate this press according to the manufacturer’s instructions may result in conditions which can produce bodily injury and/or property damage.

NOTE: The WARNINGS and IMPORTANT SAFETY INSTRUCTIONS appearing in this manual are not meant to cover all possible conditions and situations that may occur. Common sense, caution and care must be exercised when installing, maintaining, or operating the press.

Any problems or conditions not understood should be reported to the dealer, distributor, service agent or the manufacturer.

When using your press (garment finishing appliance), basic precautions should always be followed, including the following:

1. Read all instructions.

2. Use appliance only for its intended use.

3. Close supervision is necessary for any appliances being used by or near children. Do not leave appliance unattended while connected.

4. To reduce the likelihood of circuit overload, do not operate another high wattage appliance on the same circuit.

Safety signs and labels are also placed on the press. Those signs and labels are limited messages. Where needed, further explanations are provided in the manual. These signs are to be inspected for readability and replaced when missing, damaged or unreadable. Refer to Maintenance section of this manual for inspections process. Refer to parts manual for ordering information.

DANGER

To avoid possible serious injury, ensure that air and steam supply systems have adequate RELIEF VALVE PROTECTION or have the pressures sufficiently limited at the sources for safe operating pressures as specified for this equipment.

W333

WARNING

To AVOID possible serious injury, BEFORE performing maintenance or repair tasks:

• Shut off and lock out ALL electric power to the press.

• Shut off and lock out ALL air service to the press.

• Shut off and lock out ALL steam service to the press.

• Allow heated surfaces to cool.

W358

WARNING

• Failure to install, maintain, and/or operate this machine according to the manufacturer’s instructions may result in conditions which can produce serious injury, death, and/or property damage.

• Do not repair or replace any part of the machine or attempt any servicing unless specifically recommended or published in the service manual and that you understand and have the skills to carry out.

• Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the machine is properly grounded and to reduce the risk of fire, electric shock, serious injury, or death.

W335

AJ1027

Introduction

Replacement Parts

If literature or replacement parts are required, contact the source from which the machine was purchased or contact Cissel at (502) 587-1292 for the name and address of the nearest authorized parts distributor.

Nameplate Location

Always provide the machine’s serial number and model number when ordering parts or when seeking technical assistance. Refer to Figure 1.

General Description

The press is an air-operated, steam-heated garment press. The press is designed for pressing of damp garments. Major press components are:

● Steam heated head and buck.

● One air cylinder dedicated to head closing.

● One air cylinder dedicated to apply pressing

pressure once head is closed.

● A shock absorber that cushions head opening and

closing.

● Head opening springs which extend as head

closes. Springs contract to open head.

● A timer control (optional) which automatically

opens press head at set time. Timer can be turned off for manual operation.

● A two hand, anti-tie down, synchronous control

which controls press head closing.

● A filter/regulator/lubricator and lockout

downstream relieving shut-off valve at air inlet.

1 Nameplate – New Models 2 Nameplate – Old Models

Figure 1

Optional Equipment

Optional equipment available for press includes:

● Programmable timer (standard on CUCC

models)

SCR551N

● Manual water spray for hookup of water

● Manual water spray with copper reservoir

AJ1027

+ 19 hidden pages