Page 1
Network Camera with Pan/Tilt/Zoom
Quick Installation Guide
This guide describes the basic functions of
Network Camera with Pan/Tilt/Zoom.
All detailed information is described in the user’s manual.
CISEYE SECURITY TECHNOLOGIES SDN. BHD. (Co. No. 691660-P)
49, Jalan 1/119, Taman Bukit Hijau, Cheras 56000, Kuala Lumpur, Malaysia.
Tel : 603-9132 9151 (9152/9153) Fax : 603-9132 9553
Website : www.ciseye.com Email : [email protected]
™
CISEYE
Page 2
Warning Before Install
2
Contact your distributor when such cases happen.
Contact your distributor when such cases happen.
• Power off the Network Camera as soon as it is found smoking or smelt unusual.
• Keep the Network Camera away from the water. If the Network Camera is wet, power off
immediately.
• Do not place the Network Camera around the heat sources,
such as television or oven.
• Refer to your user?s manual for the operating temperature.
• Keep the Network Camera away from the direct sunlight.
• Do not place the Network Camera in high humid environments.
• Do not place the Network Camera on unsteady surfaces.
Page 3
3
• Do not touch the Network Camera when it’s lightening.
• Do not disassemble the Network Camera.
• Do not drop the Network Camera.
• Do not insert any object into the Network Camera,
such as needles.
(Antenna for wireless model only)
• Do not manually pan and tilt the Network Camera when the
power is on.
Page 4
4
1. Check Package Contents
• The Network Camera (Wire or Wireless model)
• Power adapter
• A/V cable
• Software CD
• Camera stand
• Antennas (for wireless model only)
• Remote controller
Page 5
2. Physical Description
4
Front panel
Rear panel
Antennas for wireless model only
Lens
Microphone
Status LEDs
Power cord socket
A/V out
External Mic..
EXT I/O
Ethernet 10/100 RJ45 socket
Note the serial number from the label on the unit.
This serial number is the same as the Ethernet address.
For example: 0002D1455282 = 00-02-D1-45-52-82
Page 6
3. Install Your Network Camera In Ethernet Network
6
(Antennas for Wireless model only)
1. If you have external devices such as
sensors and alarms, make connection
form I/O terminal block.
*Refer to your user’s manual for the I/O
2. Use Ethernet cable to make
connection from Ethernet port to
the hub.
* Use Category 5 Cross Cable when the
Network Camera is directly connected to a
PC
3. Finally, connect power cord to a
power outlet.
Page 7
1. Run the “Setup.exe” under the InstallationWizard directory from software CD.
2. The program will launching the installation shield.
4. Assign IP Address
7
Page 8
8
5. The Internet Explorer Connects To The Network Camera
For setup further configuration, please check user’s manual on the software CD.
Page 9
6. Client Settings (Windows XP/2000/Me/98SE)
9
At the initial access to the “Connection type” page in Windows, the web browser
will ask for a new plug-in installation, the plug-in being the Network Camera. This
plug-in has been registered for certification and can be used to change the
parameters at the client’s site. The user may click on to install the plug-in. If the
web browser does not allow the user to complete the installation, check the
Internet security to lower the security level or contact your IT or networking
supervisor.
2. Security > Default Level
1. Initial IE browser, select function item “Tools” > “Internet Options”
Page 10
10
3. Lower down the security level bar to “Low”, and press “Apply”
4. Refresh IE Browser, a question frame will pop-up to ask for download Active-X,
press “Yes”
Page 11
7. Client Settings (Windows XP SP2)
11
2. Security > Custom Level
1. Initial IE browser, select function item “Tools” > “Internet Options”
Page 12
12
4. Press ?Apply? and then ?OK?
3. Security Settings Download unsigned ActiveX Controls set “Enable” and press “OK”
Page 13
13
5. Key-in camera’s IP address and press “OK” on Information Bar
6. Click the blue bar under the Camera’s IP address in the browser, then choose
“Install ActiveX Control”
7. Recover security settings. Download unsigned ActiveX Controls set “Disable” and press
“OK” and “Apply”
Loading...