CISEYE CIP-100, CIP-100w Quick Installation Manual

CISEYE SECURITY TECHNOLOGIES SDN. BHD. (Co. No. 691660-P)

49, Jalan 1/119, Taman Bukit Hijau, Cheras 56000, Kuala Lumpur, Malaysia.

Tel : [phone] (9152/9153) Fax : [phone]

Website : www.ciseye.com Email : [e-mail]

™

CISEYE

Network Camera

Quick Installation Guide

This guide describes the basic functions of

Network Camera.

All detailed information is described in the user’s manual.

Warning Before Install

1

Contact your distributor when such cases happen.

Contact your distributor when such cases happen.

• Power off the Network Camera as soon as it is found smoking or smelt unusual.

• Keep the Network Camera away from the water. If the Network Camera is wet, power off

immediately.

• Do not place the Network Camera around the heat sources,
such as television or oven.

• Refer to your user?s manual for the operating temperature.

• Keep the Network Camera away from the direct sunlight.

• Do not place the Network Camera in high humid environments.

• Do not place the Network Camera on unsteady surfaces.

2

• Do not touch the Network Camera when it’s lightening.

• Do not disassemble the Network Camera.

• Do not drop the Network Camera.

• Do not insert any object into the Network Camera,

such as needles.

(Antenna for wireless model only)

3

1. Check Package Contents

• Network Camera

• Power adapter

• Camera stand

• Antennas (for wireless model only)

• Software CD

2. Physical Description

4

Front panel

Rear panel

Antenna for wireless model only

Lens and manual focus ring

Microphone

Status LEDs

Antenna for wireless model only

Note the serial number from the label on the unit.
This serial number is the same as the Ethernet address.

For example: 0002D1000019 = 00-02-D1-00-00-19

Reset button

3. Install Your Network Camera In Ethernet Network

5

2. Connect power cord to a power outlet

(Wireless model only)

1. Use Ethernet cable to make connection from Ethernet port to the hub

* Use Category 5 Cross Cable when the Network Camera is directly connected to PC

1. Run the “Installer Wizard” under the Software Utility directory from software CD.

2. The program will search the servers or cameras on the same LAN.

4. Assign IP Address

5. The Internet Explorer Connects To The Network Camera

6

3. After searching, the main installer

Window will pop up. Click on serial
Number that matches the one you just
Note from .2. Physical description

4. Click “Link to selected devices(s)”
to connect the Internet Explorer to the
Network Camera.

6. Setup Your Wireless Configuration For The Network Camera

7

1. Check the SSID currently set on your wireless access point (AP).

2. Go to Configuration > Network > WLAN Configuration.

5. Click Save.

3. Type in the SSID consistent

with the setting on your AP .3.

4. Select the Wireless mode as
“Infrastructure”.4.

Note :

1. SSID abbreviated from Service Set Identifier is the name assigned to the wireless

Network. The factory SSID setting is set to “default”.

2. Select “Ad-Hoc” wireless mode if you want the Network Camera to communicate
without using an AP or wireless router.

For setup further configuration, please check user’s manual on the software CD

Wireless Model Only

7. Client Settings (Windows XP/2000/Me/98E)

8

At the initial access to the “Connection type” page in Windows, the web
browser will ask for a new plug-in installation, the plug-in being the Network

Camera. This plug-in has been registered for certification and can be used to
change the parameters at the client’s site. The user may click on to install the
plug-in. If the web browser does not allow the user to complete the
installation, check the Internet security to lower the security level or contact
your IT or networking supervisor.

2. Security Default Level

1. Initial IE browser, select function item “Tools” “ Internet O ptions ”

9

3. Lower down the security level bar to “Low”, and press “Apply”

4. Refresh IE Browser, a question frame will pop-up to ask for download Active-X,

press “Yes”

8. Client Settings (Windows XP SP2)

10

2. Security “Custom Level”

1. Initial IE browser, select function item “Tools” “Internet Options”

11

4. Press ?Apply? and then ?OK?

3. Security Settings Download unsigned ActiveX Controls set “Enable” and press “OK”

12

5. Key-In camera’s IP address and press “OK” on Information Bar

6. Click the blue bar under the Camera’s IP address in the browser, then choose

“Install ActiveX Control”

7. Recover security settings. Download unsigned ActiveX Controls set “Disable” and press

“OK” and “Apply”