Cisco TelePresence MX200 G2, TelePresence MX300 G2 Administrator's Manual

Download

Page 1

Cisco TelePresence MX200 G2 and MX300 G2

Administrator guide

for Cisco TelePresence MX200 G2 and MX300 G2

Software version TC7.3 DECEMBER 2014

Page 2

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Table of contents

Introduction ............................................................................. 4

User documentation ................................................................. 5

Software ................................................................................... 5

What’s new in this version ........................................................ 6

Cisco TelePresence MX200 G2 and MX300 G2 at a glance .... 7

How to use Touch 10 ...............................................................10

Web interface ........................................................................11

Accessing the web interface ...................................................12

Changing the system password ..............................................13

The interactive menu ...............................................................14

System information ..................................................................15

About snapshots ......................................................................16

Placing a call ............................................................................ 17

Sharing content ........................................................................18

Controlling and monitoring a call .............................................19

Controlling your camera .......................................................... 20

Local layout control ..................................................................21

Controlling the far end camera ............................................... 22

Accessing call information ...................................................... 23

System configuration .............................................................. 24

Changing system settings ...................................................... 25

System status ......................................................................... 26

Managing the favorites list ...................................................... 27

Favorite list folders .................................................................. 28

Choosing a wallpaper ............................................................. 29

Choosing a ringtone ................................................................ 30

Peripherals overview ...............................................................31

User administration ................................................................. 32

Adding a sign in banner .......................................................... 36

Managing the video system’s certificates .............................. 37

Managing the list of trusted certificate authorities ................. 38

Managing pre-installed certificates for Edge provisioning ..... 40

Setting strong security mode .................................................. 41

Changing the persistency mode ............................................. 42

Deleting trust lists (CUCM only) .............................................. 43

Troubleshooting ...................................................................... 44

Downloading log files .............................................................. 45

Starting extended logging ...................................................... 46

Capturing user interface screenshots .....................................47

Upgrading the system software.............................................. 48

Adding option keys ................................................................. 49

Backup and restore ................................................................. 50

Reverting to the previously used soft ware version .................51

Factory reset ........................................................................... 52

Remote suppor t user .............................................................. 53

Restarting the system ............................................................. 54

System settings .................................................................... 55

Overview of the system set tings ............................................ 56

Audio settings ......................................................................... 59

Cameras set tings .................................................................... 60

Conference settings ............................................................... 62

FacilityService settings ........................................................... 67

H323 settings .......................................................................... 68

Logging settings ......................................................................71

Network settings ..................................................................... 72

NetworkServices settings ....................................................... 79

Peripherals settings ................................................................ 84

Phonebook settings ................................................................ 85

Provisioning settings ............................................................... 86

RTP settings ............................................................................ 88

Security settings ..................................................................... 89

SerialPor t settings....................................................................91

SIP settings ............................................................................. 92

Standby set tings ..................................................................... 96

SystemUnit settings ................................................................ 97

Time settings .......................................................................... 98

UserInterface settings............................................................101

Video settings ....................................................................... 103

Experimental settings ............................................................ 112

Setting passwords ...............................................................11 3

Setting the system password ................................................ 114

Thank you for choosing Cisco!

Your Cisco product has been designed to give you many years of safe, reliable operation.

This part of the product documentation is aimed at administrators working with the setup of the video system.

Our main objective with this Administrator guide is to address your goals and needs. Please let us know how well we succeeded!

May we recommend that you visit the Cisco web site regularly for updated versions of this guide.

The user documentation can be found on

http://www.cisco.com/go/telepresence/docs

How to use this guide

The top menu bar and the entries in the Table of contents are all hyperlinks. You can click on them to go to the topic.

Page 3

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Appendices ..........................................................................115

Connecting the Touch 10 user interface ............................... 116

Cisco VCS provisioning .........................................................119

Optimal definition profiles ......................................................120

ClearPath — Packet loss resilience ........................................121

Factory resetting the video system .......................................12 2

Factory resetting the Touch 10 user interface .......................123

Technical specification ...........................................................124

Supported RFCs ....................................................................127

User documentation on the Cisco web site ...........................12 8

Cisco contacts .....................................................................129

Page 4

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Chapter 1

Introduction

Page 5

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

This document provides you with the information required to administrate your product at an advanced level.

How to install the product and the initial configurations required are described in the Installation guide and Getting started guide, respectively.

Products covered in this guide

• Cisco TelePresence MX200 G2

• Cisco TelePresence MX300 G2

Note that the first generation of MX series products (MX300 and MX200) are covered in a separate guide.

User documentation

The user documentation for the Cisco TelePresence systems running the TC software includes several guides suitable for various user groups.

• Installation guides: How to install the products

• Getting started guide: Initial conf igurations required to get the system up and running

• Administering TC Endpoints on CUCM: Tasks to perform to start using the product with the Cisco Unified Communications Manager (CUCM)

• Administrator guide (this guide): Information required to administer your product

• Quick reference guides: How to use the product

• User guides: How to use the product

• Knowledge base articles

• Video conferencing room primer: General guidelines for room design and best practice

• Video conference room acoustics guidelines: Things to do to improve the perceived audio qualit y

• Software release notes

• Regulatory compliance and safety information guide

• Legal & license information

Downloading the user documentation

We recommend you visit the Cisco web site regularly for updated versions of the user documentation. Go to:

http://www.cisco.com/go/telepresence/docs

Guidelines how to find the documentation on the Cisco web site are included in the

User documentation on the Cisco web site appendix.

Software

You can download the software for your product from the Cisco web site. Go to:

http://www.cisco.com/cisco/software/navigator.html

We recommend reading the Sof tware Release Notes (TC7), go to:

http://www.cisco.com/c/en/us/support/collaborationendpoints/telepresence-mx-series/tsd-productssupport-series-home.html

Page 6

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

What’s new in this version

This section provides an overview of the new and changed system settings and new features in the TC7.3 software version.

Software release notes

For a complete over view of new features and changes, we recommend reading the Sof tware Release Notes (TC7). Go to:

http://www.cisco.com/c/en/us/support/collaborationendpoints/telepresence-mx-series/tsd-products-supportseries-home.html

Software download

For software download go to:

http://www.cisco.com/cisco/software/navigator.html

New features and improvements

Local preview of presentation in a call

This allows the user to preview the presentation locally before sharing it with far end. The feature has previously been available for E X systems, and is now available across the port folio.

Web snapshot s: Notify user when snapshots are taken

Both the on screen display and web interface have warnings when the snapshots feature is enabled. A notification pops up on the on screen display, when a snapshot is taken. On the web interface the administrator is warned that this notice will show up when the feature is enabled.

The system also logs when snapshots are taken, and which IP address the request was initiated from.

It is possible to allow and disallow snapshots remotely, but not to observe the room without the user s being notif ied.

System configuration changes

New configurations

Cameras Preset TriggerAutofocus

H323 Profile Encr yption KeySize

NetworkServices CDP Mode

Configurations that are removed

H323 Profile [1] Encryption MinKeySize

Configurations that are modified

FacilityService Service [5] Name

OLD: <S: 0, 255> NEW: <S: 0, 1024>

FacilityService Service [5] Number

OLD: <S: 0, 255> NEW: <S: 0, 1024>

Video AllowWebSnapshots

OLD: <Off/On>, default Off NEW: <Of f/On/LocalDeviceOnly>, default

LocalDeviceOnly

Page 7

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Features and benefits

• Easy to install – one piece plus f loor stand, wheel base, or wall mount brackets (VESA mount).

• Self-configuring with Cisco Unified Communications Manager (UCM), Cisco TelePresence Video Communication Server (VCS), or Cisco WebEx TelePresence provisioning. You need to authenticate your endpoint to the network.

• MX200 G2: Cisco TelePresence PrecisionHD camera with pan, tilt, and 5x zoom.

MX300 G2: Cisco TelePresence PrecisionHD camera with pan, tilt, and 8x zoom.

• MX200 G2: High-qualit y 42 inch LCD display with 1920×1080 resolution (1080p60) and 16:9 aspect ratio.

MX300 G2: High-qualit y 55 inch LCD display with 1920×1080 resolution (1080p60) and 16:9 aspect ratio.

• Two front speakers that provide superior audio quality.

• Integrated microphone, and support for t wo external Cisco TelePresence Table Microphone 20.

• 10 inch Cisco TelePresence Touch 10 user interface that offers simple control.

• Standards-based.

• Support for H.323 and Session Initiation Protocol (SIP) calls with bandwidth up to 6 Mbps point-to-point.

• Support for video resolutions up to 1080p60.

• Support for high-definition multimedia and presentation sharing at 1080p30 resolution.

• Support for the dual display feature that allows another screen to be added for content sharing.

• Support for the one-button-to-push feature for starting scheduled meetings.

• Embedded MultiSite conferencing option that allows up to three additional participants.

• The systems take advantage of the Cisco TelePresence Total Solution approach, including Cisco TelePresence Multiway features, recording and streaming, and firewall traversal ser vices.

• Natively supported by Cisco UCM version 8.6.2 and later.

MX300 G2

MX200 G2

Cisco TelePresence® MX200 G2 and MX300 G2 are part of the second generation of MX Series multipurpose endpoints.

MX200 G2 and MX300 G2 blend aesthetics, functionalit y and ease of use. 1080p60 high-definition (HD) performance and new features such as dual display and an embedded fourway MultiSite conferenceing option deliver more power and flexibilit y. The Cisco TelePresence Touch 10 user interface offers a larger screen size and a user-friendly experience.

MX200 G2 and MX300 G2 systems are easy to install, so you can quickly transform any meeting space into a telepresenceenabled team room.

MX200 G2 and MX300 G2 can meet your needs whether you are just getting star ted with video communications or are planning to video-enable your entire organization.

Cisco TelePresence MX200 G2 and MX300 G2 at a glance

Page 8

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Mounting options

(floor stand, wheel base, wall mount)

Cisco TelePresence MX300 G2

Two external microphones

Touch 10 user interface

Internal microphone

55” LCD monitor

Precision HD camera

Embedded codec

Loudspeakers

Page 9

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Mounting options

(floor stand, wheel base, table stand, wall mount)

Cisco TelePresence MX200 G2

One external microphone

Touch 10 user interface

Internal microphone

42” LCD monitor

Precision HD camera

Embedded codec

Loudspeakers

Page 10

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Tap Dial to invoke

the dial pad.

Tap Contacts to invoke the list of contacts including Favorites,

Directory and Histor y.

Tap Meetings to invoke a list of

upcoming scheduled meetings.

Tap Messages to invoke the

voice mail system, if applicable.

Tap Share to star t sharing content and to conduct presentations.

Press and hold the left side of

the Volu me button to decrease

the loudspeaker volume and the

right side to increase the volume.

Press the Microphone button

to mute / unmu te microp hone.

Time of day is indicated

in the upper right corner.

Tap the Camera icon to activate

self-view and camera control.

Tap the ? to contact or access

the Help desk, if available.

Tap the upper left cor ner to activate / deactivate the Do not disturb feature,

to activate /deactivate the Standby feature, and to access the Settings.

How to use Touch 10

The Touch 10 user interface and its use are described in full detail in the User guide for your video system.

Page 11

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Chapter 2

Web interface

Page 12

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

1. Connect to the video system

2. Sign in

Enter the user name and password for your video system and click Sign In.

The system is delivered with a default user named admin with no password. Leave the Password field blank when signing in for the first time.

It is mandator y to set a password for the admin user, see the next page.

Signing out

Hover the mouse

over the user

name and choose

Sign out from the

drop-down list.

Accessing the web interface

The web interface provides full configuration access to your video conference system.

You can connect from a computer and administer the system remotely.

In this chapter you will find information how to use the web interface for system configuration and maintenance.

We recommend that you use the latest release of one of the major web browsers.

Open a web browser and enter the IP address of the video system in the address bar.

How to find the IP address

Touch controller: Tap the contact information in the upper lef t corner of the Touch controller and open the

Settings menu. Then tap System Information.

Page 13

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Changing the system password

It is mandator y to set a password for a user with ADMIN rights in order to restrict acces s to system configuration. This includes the default admin us er.

A warning, saying that the system password is not set, is shown on screen until you set a password.

You can read more about passwords in the

Setting passwords ch ap ter.

1. Open the Change Password dialog

Hover the mouse over your the name, and choose Change password in the drop-down list.

2. Set the new password

Enter your current and new passwords as requested, and click Change password for the change to take effect.

If the password currently is not set, leave the Current password field blank.

Page 14

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Configuration

System Configuration

System Status

Local Contents Management

Personalization

The interactive menu

The web interface provides access to tasks and configurations. They are available from the main menu, which appears near the top of the page when you have signed in.

When you hover the mouse over an item in the main menu, you can navigate to its related sub-pages.

Main menu

Hover the mouse over a main menu item in order to see the titles of the related sub-pages.

Click a sub-page’s title to open it. Click the main menu item itself if there are no subpages. Only pages that the user has access rights for are shown

Click Home to return to the System Information page.

Call Control Maintenance

Software Upgrade

Option Keys

Backup and Re store

Diagnostics

Troubleshooting

Peripherals

User Administration

Startup Scripts

Sub-pages

You can read more about u ser admini stratio n, user roles a nd acces s

rights in th e User administration section.

API

Call History

Security

Log Files

User Interface Screenshots

System Recovery

Restart

Page 15

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

System information

The video system’s Home page shows an overview of the basic set-up and status of the system

This includes information like system name and product t ype, which soft ware version the system runs, its IPaddress, etc. Also the registration status for the video networks (SIP and H.323) is included, as well as the number/URI to use when making a call to the system.

Navigate to: Home

The system infor mation shown in the illu stration s erve as an

example. Your syste m may be dif ferent.

Page 16

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

About snapshots

The snapshot feature allows snapshots of the video system’s input sources to be displayed on the Call Control page. This applies both when the system is idle and in a call. In a call, snapshots of the far end system may be displayed as well.

This feature might come in handy when administering the video system from a remote location, e.g. to check the camera view and control the camera.

The video system’s users will be notified when the snapshot feature is in use. A notif ication saying that the administrator is visually monitoring the room is displayed on the video system’s main display.

Enabling the snapshot feature

By default, the snapshot feature is disabled for devices that are not physically connected to the video system (including the web interface).

Enable the feature using the web interface.

• Go to the Configuration tab and select System

Configuration

• Navigate to Video > AllowWebSnapshots and choose On.

• Click Save for the change to take effect.

About far end snapshots

As long as the Video AllowWebSnapshots setting is switched On on the local video system, far end snapshots may be captured even if snapshots are disallowed on the far end video system. Snapshots are prohibited only for encrypted calls.

You can also prohibit snapshots from being taken by switching the Conference FarEndControl Mode setting Off on the far end video system.

Camera control

Snapshots are captured during both local

and remote camera control. Camera control

is enabled by clicking the camera icon.

Navigate to: Call C ontrol

View snapshots from the input sources

Click in this area to view snapshots from the

selected main source or presentation source.

Snapshots of the main or presentation source will

be displayed for approximately 10 seconds. .

Page 17

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Placing a call

You can use the Call Control page to place a call.

Even if the web inter face is used to initiate the call, it is the video system (display, microphones and loudspeakers) that is used for the call; it is not the PC running the web interface.

Calling

You can call someone either by choosing a contact name in the Local, Directory or Recents lists, or by typing a complete URI or number in the Search or Dial field. Then click Call in the associated contact card.

Searching the contact lists

Enter one or more characters in the Search or Dial field. Matching entries from the Local, Directory and Recents lists will be listed as you type.

Select the correct entr y in the list and click Call.

Calling more than one

A point-to-point video call (a call involving two parties only) can be expanded to include one more participant on audioonly.

If your system is using the optional built-in MultiSite feature, up to four participants, your self included, can join the video call (conference). In addition, one more par ticipant can join on audio-only.

Follow the same procedure to call the next conference participant as you did when calling the f irst par ticipant.

Calling more than one using a conference bridge (CUCM ad hoc conferencing or MultiWay) is not supported from the web interface, even if it is suppor ted by the video system itself.

Calling someone

Click a contact name, either in the

Local, Directory or Recents lists.

Then click Call in the contact card.

Alternatively, enter the complete URI

or number in the Search and Dial field. Then click the Call button that appears nex t to the URI or number.

Ending a call

If you want to terminate a call or conference, click End

all. Confirm your choice in

the dialog that appears.

To disconnect just one participant in a conference, click the

button for that

participant.

Holding and resuming

Use the

button next to the participant’s name to put him on hold.

To resume the call, use the button that is present when a participant is on hold.

Navigate to: Call C ontrol

Page 18

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Navigate to: Call C ontrol

Sharing content

You can connect a presentation source to one of the external inputs of your video system. Most often a PC is used as presentation source, but other options may be available depending on your system setup.

While in a call you can share content with the other participant(s) in the call (far end).

If you are not in a call, the content is shared locally on your display.

Sharing content

1. Choose a Presentation source from the drop-down list.

2. Click Start Presentation.

Stop content sharing: Click the Stop Presentation button that is present

while sharing.

Page 19

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Controlling and monitoring a call

You can control and monitor several call features using the Call Control page.

Volume down

Navigate to: Call C ontrol

Call details

If necessary,

scroll your browser to

see all call details.

Show/hide

call details

Volume up

Microphone mute

Click the

information button

to show details

about the call.

Click the but ton

again to hide the

information.

Click the but ton to mute the microphone. Then the text changes to

Microphone: Off.

Click again to unmute.

Page 20

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Navigate to: Call C ontrol

Controlling your camera

When you control the video system’s camera (pan, tilt, zoo m) from the Call Control page snapshots from the camera is shown on the web interface.

As a consequence, a notification will be sent to the users of the video system (shown on the main dispaly) that an administrator is monitoring their video.

Camera presets

If one or more presets are defined,

click Preset s... to open a list of

available presets.

Click a preset’s name to move the

camera(s) to the preset position.

Click OK to close the window.

You cannot use the web interface to

define a preset; you should use the

video system’s Touch user interface.

Control the camera

1. Click the camera icon to open the camera control window.

2. Place the cursor in the image to enable the controls.

If you are not allowed to control the

camera, the controls will not appear when

you place the cursor in the image.

3. Use the left and right arrows to pan the camera; the up and down arrows to tilt it;

and + and - to zoom in and out.

Page 21

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Local layout control

You can choose a local layout using the Call Control page.

The term layout is used to describe the various ways the videos from the conference participants and a presentation can appear on the screen. Dif ferent types of meetings may require different layouts.

Change the layout

Click Change layout, and choose your preferred layout in the window that opens.

The set of layouts to choose from depends on the system configurations.

You may change the layout while in a call.

Navigate to: Call C ontrol

Page 22

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Controlling the far end camera

While in a call, you can control the remote participant’s camera (far end) provided that:

• The Conference FarEndControl Mode setting is switched On on the far end video system.

• The far end camera has pan, tilt or zoom functionality. Only the relevant controls will appear.

Control the remote participant’s camera

1. Click the camera icon to open the remote camera control window.

2. Place the cursor in the image to enable the controls.

If you are not allowed to control the far end camera, the controls will not appear when you place the cursor in the image.

3. Use the left and right arrows to pan the camera; the up and down arrows to tilt it; and + and - to zoom in and out.

Navigate to: Call C ontrol

Page 23

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Accessing call information

A call state indicator is available in the top bar in the web interface. It shows whether the system is in a call or not, and how many calls it is engaged in. You may also be notified about incoming calls.

Call state indicator

The call state indicator is

available on all pages except

the Call Control page.

The badge indicates the number

of active calls. If the system is

idle, there is no badge.

Click the indicator to get more

details about connected calls.

Call control

Use these buttons to:

• Show call details

• Put the call on hold

• Disconnect the call

Incoming call notification

As default, a notification is given when the system receives a call.

Check this box, if you do not want to receive such notifications.

Opening the Call Control page

Click Open Call Control to go straight to the Call Control page.

Page 24

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Selecting a category

The system set tings are structured in categories.

Choose a category in order to display the related settings.

System configuration

The system set tings are grouped in several categories. When you choose a category in the left pane all related settings appear to the right

Each system set ting is fur ther described in the

System settings cha pt er.

Expanding and collapsing lists

Use these buttons to expand and collapse all or individual lists.

Searching for settings

Enter as many letters as needed in the search field.

All settings (including the value space) containing these letters will be highlighted.

The configur ation show n in the illus tration se rve as an exam ple.

Your system may be co nfigured different ly.

Navigate to: Configuration > System Configuration

Page 25

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Changing system settings

All system set tings can be changed from the System Configuration page

. The value space for a setting is specified

either in a drop-down list or by text following the input field.

Different settings may require different user credentials. In order to be sure that an administrator is able to change all system settings, an administrator user must possess all user roles.

You can read more about user administration and user roles in the User administration cha pt er.

Drop-down lis t

Click the arrow to open the drop-down list, and choose the preferred value.

Click Save for the change to take effect.

Text input field

Enter new text in the input field.

Click Save for the change to take effect.

The configur ation show n in the illus tration se rve as an exam ple.

Your system may be co nfigured different ly.

Navigate to: Configuration > System Configuration

Page 26

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Navigate to: Configuration > System Status

Selecting a category

The system status is structured in

categories. Choose a category in order

to display the related status infor mation.

Expanding and collapsing lists

Use these buttons to expand and collapse all or individual lists.

Searching for status entries

Enter as many letters as needed in the search field.

All entries (including the value space) containing these let ters will be highlighted.

System status

The system status is grouped in several categories. When you choose a category in the left column, the related status appears in the window to the right

The status show n in the illus tration s erve as an exa mple. The st atus

of your system may be diffe rent.

Page 27

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Managing the favorites list

The entries in the favorites list can be accessed from the Touch controller and the Web interface.

Adding a contact

Click Add contact and f ill in the form that pops up. Then click Save to store the contact in the Favorites list.

Editing contact details

Click a contacts name

followed by Edit contact.

Change the details in the form

as appropriate and click Save.

Deleting a contact

Click a contacts name

followed by Edit contact. Then

click Delete to remove the

entry from the Favorites list.

Adding a contact method*

You can store more than one contact method for each contact, e.g. video, telephone and mobile.

Storing a contact in a folder

Choose the appropriate folder

from the drop down list.

No folder means that the contact

will be stored at the top level.

Note that only the f irst con tact metho d appear s in the Favorites list

on the Touch contr oller.

Navigate to: Configuration > Local Contacts Management

Import/Export contacts from file

Click Export to save the Local contacts in a file; and click Import to bring in contacts from a file.

Note that all current contacts will be discarded when impor ting new contacts from a file.

Page 28

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Favorite list folders

The entries in the Favorites list can be organized in folders.

Opening a folder

Click the folder name to open the folder and show its list of contacts.

Adding a folder

Click Add folder and fill in the form that pops up. Then click

Save to create the folder.

Changing or Deleting a folder

Click Edit folder and update the

information in the form that pops up.

Then click Save to store the changes

Click Delete to remove the folder

and all its contacts and sub-folders.

Confirm your choice in the dialog that

pops up.

Navigate to: Configuration > Local Contacts Management

Page 29

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Choosing a wallpaper

If you want the company logo or another custom picture as background on the video display, you may upload and use a custom wallpaper.

Activate/deactivate a wallpaper

Available wallpapers are represented by a miniature. If you have uploaded a custom wallpaper, it will appear in the list.

Click the miniature to switch to the corresponding wallpaper. Choose None if you do not want a wallpaper.

The chosen option is highlighted.

Upload a custom wallpaper

Click Bro wse ... and locate your custom wallpaper image file.

Click Upload to save the file on the video system.

Supported file formats: BMP, GIF, JPEG, PNG Maximum file size: 4 MByte

The custom wallpaper will be automatically activated once uploaded.

Navigate to: Configuration > Personalization

Delete the custom wallpaper

Click the delete symbol to remove the custom

wallpaper from the video system. Note that this

will remove the image file completely; you have to

upload it anew if you want to use it again.

Page 30

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Choosing a ringtone

You can choose from a set of predefined ringtones. The chosen ringtone can be played back from this page.

The ringtone will be played back on the video system itself, and not through the web inter face.

Changing ringtone

Choose a ringtone from the drop-down list, and click Save to make it the active ringtone.

Playing back the ringtone

Click the play button ( ► ) to play back the ringtone.

Use the stop button (  ) to end the playback.

Navigate to: Configuration > Personalization

Set the ringtone volume

Use the slide bar to adjust the ringtone volume.

Page 31

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Peripherals overview

This page shows an overview of devices that are connected to the video system, like video inputs and outputs, cameras, microphones, ISDN Links and Touch controllers

The peripher als shown in t he illustr ation ser ve as exampl es. Your

system may have differen t periphe rals and video input /output configurations.

Managing ISDN Link

If an ISDN Link is paired to the video system it can be managed from this page.

How to configure and use the ISDN Link are described in the ISDN Link documentation on

http://www.cisco.com/go/isdnlink-docs

Navigate to: Configuration > Peripherals

Page 32

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

User administration

You can manage your video conference system’s user accounts from this page.

The default user account

The system comes with a default administrator user account with full access rights. The user name is admin and no password is set.

It is mandator y to set a password for the admin use r.

Read more about passwords in the Setting passwords ch apt er.

About user roles

A user account must hold one or a combination of several user roles.

The following three user roles, with non-overlapping rights, exist:

• ADMIN: A user holding this role can create new users and change most settings. The user neither can upload audit certif icates nor change the security audit settings.

• USER: A user holding this role can make calls and search the phone book. The user can modify a few settings, e.g. adjusting the ringtone volume and setting the time and date format.

• AUDIT: A user holding this role can change the security audit configurations and upload audit certificates.

An administrator user account with full access rights, like the default admin user, must possess all the three roles.

Default user account

The system comes with admin as the default user account. This user has full access rights.

Navigate to: Configuration > User Administration

(page 1 of 4)

Page 33

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

User administration

Creating a new user account

Follow these steps in order to create a new user account:

1. Click Add new user....

2. Fill in the Username and Password

, and check the

appropriate user roles check boxes.

As a default the user has to change the password when signing in for the first time.

Do not fill in the Client Cer tificate DN (Distinguished Name) field unless you want to use certificate login on HTTPS.

3. Set the Status to Active to activate the user.

4. Click Create User to save the changes.

Use the Back button to leave without making any changes.

Navigate to: Configuration > User Administration

The pass word is used w ith the web inte rface an d command l ine

interface.

(page 2 of 4)

Page 34

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

User administration

Changing user privileges

Follow these steps in order to change the user privileges:

1. Click the name of an existing user to open the Editing user window.

2. Check the appropriate user roles check boxes, decide if the user has to change the password on the next sign in, and fill in the Client Certificate DN f ield if using certificate login on HT TPS.

3. Click Update User to save the changes.

Use the Back button to leave without making any changes.

Changing the password

Follow these steps in order to change the password*:

1. Click the name of an existing user to open the Editing user window.

2. Enter the new password in the appropriate input fields.

3. Click Change Password to save the change.

Use the Back button to leave without making any changes.

Navigate to: Configuration > User Administration

The pass word is used w ith the web inte rface an d command l ine

interface.

(page 3 of 4)

Page 35

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

User administration

Deactivating a user account

Follow these steps in order to deactivate a user account:

1. Click the name of an existing user to open the Editing user window.

2. Set the Status to Inactive.

3. Click Update User to save the changes.

Use the Back button to leave without making any changes.

Deleting a user account

Follow these steps in order to delete a user account:

1. Click the name of an existing user to open the Editing user window.

2. Click Delete <user name>... and confirm when prompted.

Navigate to: Configuration > User Administration

(page 4 of 4)

Page 36

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Adding a sign in banner

If a system administrator wants to provide initial information to all users, he can create a sign in banner. The message will be shown when the user signs in to the web interface and the command line interface.

Adding a sign in banner

Enter the message that you

want to present to the user

when signing in, and click

Save to activate the banner.

Navigate to: Configuration > Sign In Banner

Page 37

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Managing the video system’s certificates

Certif icate validation may be required when using TLS (Transport Layer Security).

A server or client may require that your video system presents a valid certif icate to them before communication can be set up.

The video system’s certificates are text files that verif y the authenticity of the system. These cer tificates may be issued by a certif icate authority (CA).

The certificates are listed as shown in the illustration to the right

. They can be used for the following services: HTTPS

server, SIP, IEEE 802.1X and audit logging.

You can store several cer tificates on the system, but only one certif icate can be used for each ser vice at a time.

If authentication fails, the connection will not be established.

Enabling and disabling certificates

Use the buttons to switch a cer tificate on or off for the different services.

You can also view a certificate, and delete a certificate using the corresponding buttons.

Contact your system administrator to obtain the following file(s):

• Certif icate (file format: .PEM)

• Private key, either as a separate file or included in the same file as the certificate (file format: .PEM format)

• Password (required only if the private key is encr ypte d)

The certificate and the private key will be stored in the same file on the video system.

Adding a certificate

1. Click Browse... and find the C ertificate and Private key file(s) on your computer.

2. Fill in the Password if required.

3. Click Add certificate... to store the certif icate on your system.

Navigate to: Configuration > Security: Certificates tab

The cer tificate s and cert ificate i ssuers sh own in the ill ustratio n serve as examples. Your sys tem may have othe r certif icate(s).

Page 38

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Managing the list of trusted certificate authorities

Certif icate validation may be required when using TLS (Transport Layer Security).

Your video system may be set up to require that a server or client presents its certificate to the video system before communication can be set up.

The certificates are text files that verify the authenticit y of the server or client. The cer tificates must be signed by a trusted certificate authority (CA).

To be able to verify the signature of the certificates, a list of trusted CAs must reside on the video system. The certificates of the CAs are listed as shown in the illustration to the right

The list must include all CAs needed in order to verify certif icates for audit logging, HT TPS, SIP and IEEE 802.1X connections.

If the server cannot be authenticated, the connection will not be established.

The cer tificate a nd certi ficate is suers shown in the illustration s erve as example s. Your system will ha ve other cer tifica te(s).

Contact your system administrator to obtain the CA certificate list (file format: .PEM).

Viewing and deleting certificates

You can view a certificate, and delete a certificate using the corresponding buttons.

Uploading a list of certificate authorities

i. Click Bro wse ... and find the file containing a

list of CA certificates (file format: .PEM) on

your computer.

ii. Click the Add certificate authority... to store

the new CA certificate(s) on your system.

The entries in a new file with CA certif icates will be appended to the existing list, so that the previously stored cer tificates will not be deleted.

Navigate to: Configuration > Securit y: CAs tab

(page 1 of 2)

Page 39

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

iii

Managing the list of trusted certificate authorities

As from software version TC7.2, the signature of an audit server is verified using the same CA list as other servers/clients.

Setting up secure audit logging

Audit logging records all sign in activit y and configuration changes on your video system.

Audit logging is disabled by default, but you can enable it using the Security > Audit > Logging > Mode setting.

In ExternalSecure audit logging mode the video system sends encr ypted audit logs to an external audit server (syslog server), which identity must be verified by a signed certificate.

If the audit server cannot be authenticated, the logs will not be sent.

Always upload the list of trusted certificate authorities before enabling secure audit logging.

Enable secure audit logging

i. Go to the System Configuration

page and choose the Security category.

ii. Enter the Address of the audit

server. If you choose Manual

PortAssignment, you must also

enter a Port number for the audit server. Click Save for the changes to take ef fect.

iii. Choose ExternalSecure from the

Logging Mode drop-down list.

Click Save for the change to take effect.

Navigate to: Configuration > Securit y: CAs tab / Configuration > System Configuration

(page 2 of 2)

Page 40

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Managing pre-installed certificates for Edge provisioning

The list of pre-installed certificates that is shown on this page in the web interface

, contains certificates that will be used when the video system is provisioned by Cisco Unified Communications Manager (CUCM) via Expressway (Edge). Only Edge infrastructure certificates will be checked against this list.

If the Edge infrastructure certificate validation fails, the video system will not receive the provisioning and not be registered.

Factory resetting the video system will not delete the list of pre-installed certificates.

Navigate to: Configuration > Securit y: Preinst alled CAs tab

The cer tificate a nd certi ficate is suers shown in the illustration s erve as example s. Your system will ha ve other cer tifica te(s).

Viewing or disabling certificates

You can view a certificate, and disable a cer tificate using the corresponding buttons.

You can disable all the preinstalled certificates, and use a manually uploaded list of certif icates for verification instead. See the Configuration > Security:

CAs page how to upload trusted

certif icates to the video system manually.

Page 41

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Setting strong security mode

Strong security mode should be used only when compliance with DoD JITC regulations is required.

Read the provided information carefully before setting strong security mode.

Strong security mode sets very strict password requirements, and requires all users to change their password on the next sign in.

Setting strong security mode

Read carefully about the consequences of

strong security mode before you continue.

1. If you want to use strong security mode,

click Enable strong security mode....

Confirm your choice in the dialog box

that appears.

The system will restart automatically.

2. Change the password when you are

prompted. The new password must meet

the strict criteria as described.

How to change the system password

is described in the Setting passwords

section.

Return to normal mode

When in strong security mode, the system

can be restored to normal mode by clicking

Disable strong security mode.... Confirm your

choice in the dialog box that appears

The system will restart automatically.

Navigate to: Configuration > Securit y: Strong Security Mode tab

Page 42

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Changing the persistency mode

By default, all persistency settings are set to Persistent. This means that configurations, call histor y, internal logs, local phonebook / favorites list and IP connectivity information are stored as normal. A system restart does not delete information.

As a general rule, we recommend NOT to change the default settings for persistency. But in the case were a

new user is not supposed to see or trace back to any kind of logged information from the previous session, Non- persistent mode must be used.

In order to clear/delete information that was stored before changing to Non-persistent mode, you should consider to factory reset the video system.

There is more information about performing a factor y reset in the Factor y resetting appendix.

When in Non-persistent mode, the following information will be lost/cleared each time the system restarts:

• System Configuration changes that have been made since the last system restart.

• Information about calls that are placed or received since the last system restart (call history).

• Internal log f iles that has been made since the last system restart.

• Changes that are made to the local contacts / favorites list since the last system restart.

• All IP related information (DHCP) from the last session.

Checking the persistency status

The radio buttons that are active when you open the Security page and go to the Non-persistent Mode tab, shows the current persistency status of the video system.

You can also see the status by checking Security >

Persistency on the Configuration > System Status page.

Changing the persistency settings

1. Set the persistency settings for the five categories as desired.

2. Click Save and reboot....

The system will restart. After the restart, behavior according to the new persistency settings will start.

Note that logs, configurations etc. that was stored before you switch to Nonpersistent mode, will not be cleared or deleted.

Navigate to: Configuration > Securit y: Non-persistent Mode tab

Page 43

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Deleting trust lists (CUCM only)

The information on this page is only relevant for video systems that are registered to a Cisco Unif ied Communications Manager (CUCM).

The web interface can be used to delete existing trust lists (CTL and ITL) that are stored on the video system. Normally, you will not delete the old CTL and ITL files, but there are a few cases when you will need to delete them.

The trust lists’ fingerprints and an overview of the certif icates in the lists are displayed on the web page. This information can be useful for troubleshooting.

For more information about CUCM and trust lists, read the Administering TC Endpoints on CUCM guide available on the Cisco web site.

Navigate to: Configuration > Securit y: CUCM tab

Page 44

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Troubleshooting

The troubleshooting page lists the status for some common sources of errors. The list may be different for different products and installations

Note that critical issues and errors are clearly marked in red color; warnings are yellow.

Run diagnostics

Click Re-run diagnostics to make sure the information in the list is up-to-date.

The mess ages show n in the illus tration se rve as examp les. Your system may sh ow other information.

Leave standby mode

This button is only visible when the system is in standby mode. If in standby mode, click Deactivate standby to wake up the system.

Navigate to: Diagnostics > Troubleshooting

Page 45

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Downloading log files

The log files* are Cisco specific debug f iles which may be requested by the Cisco support organization if you need technical support.

The current log files are time stamped event log files.

All current log files are archived in a time st amped historical log file each time the system restarts. If the maximum number of historical log files is reached, the oldest one will be overwritten.

Downloading all log files

Click Download logs archive and follow the instructions.

An anonymized call histor y is included in the log files by default.

Use the drop down list if you want to exclude the call history from the log files, or if want to include the full call history (non-anonymous caller/callee).

The log fi les shown in t he illust ration ser ve as exampl es. Your system may have other fil es.

Open/save one log f ile

Click the file name to open the log file in the web browser; right click to save the file on the computer.

Navigate to: Diagnostics > Log Files

Refresh the list of log files

Page 46

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Starting extended logging

Extended logging mode may be switched on to help diagnose network issues and problems during call setup. While in this mode more information is stored in the log files.

Note that extended logging uses more of your video system’s resources, and may cause your video system to underperform. You should only use extended logging mode when troubleshooting an issue.

Start extended logging

Click Start extended logging.

Extended logging lasts for 10 minutes. You can stop the extended logging before it times out by clicking the Stop extended logging button that appears when extended logging is on.

As default, the network traffic is not captured. Use the drop down menu if you want to include a full or partial capture of the network traf fic.

Navigate to: Diagnostics > Log Files

Page 47

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Capturing user interface screenshots

You can capture screenshots both of a Touch controller that is connected to the video system, and of the on-screen display (menus, indicators and messages on the main display).

Deleting screenshots

Navigate to: Diagnostics > User Interface Screenshots

If you want to delete all screenshots, click Remove all.

To delete just one screenshot, click the

button for that screenshot.

Capture a screenshot

Click Take screenshot of Touch Panel to capture a screenshot of the Touch controller, or click Take screenshot of OSD to capture a screenshot of the on-screen display.

The screenshot will display in the area below the buttons. Note that it can take up to 30 seconds before the screenshot is ready.

All captured snapshots are included in the list above the but tons. Click the screenshot ID to display the image.

Page 48

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Upgrading the system software

This video conference system is using TC soft ware. The version described in this document is TC7.3.

Contact your system administrator if you have questions about the sof tware version.

Software release notes

For a complete over view of the news and changes, we recommend reading the Sof tware Release Notes (TC7).

Go to: http://www.cisco.com/c/en/us/support/collaboration-

endpoints/telepresence-mx-series/tsd-products-supportseries-home.html

New software

For software download, go to the Cisco Download Software web page:

http://www.cisco.com/cisco/software/navigator.html.

Then navigate to your product.

The format of the file name is “s52010tc7_3_0.pkg” (each software version has a unique file name).

Navigate to: Maintenance > Sof tware Upgrade

Install new software

Download the appropriate software package from the Cisco Software Download web page (see link to the left) and store it on your local computer. This is a .pkg file.

i. Click Bro wse ... and find the downloaded .pkg file

that contains the new soft ware.

ii. Click Install software to start the installation

process.

The complete installation may take up to 30minutes. You can follow the progress on the web page. The system restarts automatically after the installation.

You must sign in anew in order to continue working with the web interface after the restart.

Page 49

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Adding option keys

Your video system may or may not have one or more software options installed. In order to activate the optional functionality the corresponding option key must be present on the video system.

Option keys are not deleted when per forming a software upgrade or factory reset, so they need to be added only once.

Each video system has unique option keys, for example: 1R000-1-AA7A4A09

Contact your Cisco representative to obtain information about available option keys, and how to get the required key(s).

Navigate to: Maintenance > Option Keys

Add an option key

i. Enter an Option Key in the

appropriate text input field.

ii. Click Add option key.

If you want to add more than one option key, repeat these steps for all keys.

Page 50

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Backup and restore

All the system settings, which are available on the System configuration page, can be listed on-screen or stored as a text file.

The text file can be loaded back onto the system, thereby restoring the configuration.

Backing up or showing the current configuration

Click Preview backup to display the current settings on-screen.

Click Take backup to store the configuration as a text file.

Restoring an earlier configuration

Click Bro wse ... and find the file with the configuration you want to restore.

Click Restore to reconfigure the system as defined in the file.

Navigate to: Maintenance > Backup and Restore

Page 51

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Reverting to the previously used software version

If there is a severe problem with the video system, switching to the previously used software version may help solving the problem.

If the system has not been factor y reset since the last software upgrade, the previously used software image still resides on the system; you do not have to download the software again.

Reverting to the previously used soft ware version should only be done by a system administrator or in contact with Cisco technical support.

We strongly recommend that you backup your system’s log files and configuration before you swap to the other software image.

Navigate to: Maintenance > System Recovery: Backup tab and Soft ware Recover y Swap tab

1. Revert to the previously used software version by clicking Switch to software

TCx.y.z..., where x.y.z indicates the

software version.

2. Click Yes to confirm your choice, or

Cancel if you have changed your mind.

Wait while the system resets. The system will restart automatically when finished.

1. Backing up log files and system configuration

We recommend that you backup your system’s log files and configuration before you swap to the other software image.

Click Download Logs and Download

Configuration Backup and follow the

instructions to save the files on your computer.

2. Reverting to the previously used software version

Page 52

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Factory reset

If there is a severe problem with the video system, the last resort may be to reset it to its default factory settings. Always consider rever ting to the previously used software image before performing a factor y reset. In many situations this will recover the system*.

A factory reset should only be perfor med by a system administrator or in contact with Cisco technical support.

When factor y resetting the video system the following happens:

• The call logs will be deleted.

• Passwords will be reset to default.

• All system parameters will be reset to default values.

• All files that have been uploaded to the system will be deleted. This includes, but is not limited to, custom wallpapers, certificates and favorites list.

• The previous (inactive) software image will be deleted.

• Option keys will not be affected.

The system restarts automatically after the reset. It is using the same sof tware image as before.

We strongly recommend that you backup your system’s log files and configuration before you per form a factor y reset.

It is not possible to undo a factor y reset.

There is more information about performing a factor y reset in the Factory resetting appendix.

2. Performing a factor y reset

Read the provided information carefully

before you click Per form a factory reset....

Click Yes to confirm your choice, or Cancel if you have changed your mind.

Wait while the system resets. The system will restar t automatically when finished.

Navigate to: Maintenance > System Recovery: Backup tab and Factory Reset tab

1. Backing up log files and system configuration

We strongly recommend that you backup your system’s log files and configuration before you perform a factor y reset; otherwise these data will be lost.

Click Download Logs and Download

Configuration Backup and follow the

instructions to save the files on your computer.

Read abou t software swappin g in the Rever ting to the p reviously

used software version section.

Page 53

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Remote support user

In cases where you need to diagnose problems on the video system you can create a remote suppor t user.

The remote support user will be granted read access to the system and will have access to a limited set of commands that can aid troubleshooting.

You will need assistance from Cisco Technical Assistance Center (TAC) to acquire the password for the remote support user.

The remote support user should only be enabled for troubleshooting reasons when instructed by Ci sc o TA C.

Navigate to: Maintenance > System Recovery: Remote Support User tab

Create remote support user

1. Open a case with Cisco TAC.

2. Click Create user.

3. Copy the text in the To ke n field and send to Cisco TAC.

4. Cisco TAC will generate a password.

The remote support user is valid for seven days, or until it is deleted.

Delete remote support user

Click Delete user.

Page 54

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Restarting the system

The system can be shut down or restarted remotely using the web interface.

Restarting the system

Click Restart TelePresence device... to restart the system.

It will take a few minutes before the system is ready for use.

Shutting down the system

Click Shutdown TelePresence device... to shut down the system.

The system cannot be turned on again remotely; you must press its power but ton physically to turn it on.

Navigate to: Maintenance > Restart

Page 55

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Chapter 3

System settings

Page 56

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

* The Settings menu can b e access ed from the dr op down wind ow

that appears when you t ap the cont act inform ation in the u pper, left corner of the Touch user inter face.

Overview of the system settings

In the following pages you will find a complete list of the system settings which are configured from the System

Configuration page on the web interface. The examples show

either the default value or an example of a value.

Open a web browser and enter the IP address of the video system; then sign in.

To find the IP address (IPv4 orIPv6), open the

Settings

menu on the Touch user interface and tap

System Information.

Audio settings ....................................................................... 59

Audio DefaultVolume............................................................... 59

Audio Input Microphone [1] ..................................................... 59

Audio Microphones Mute Enabled .......................................... 59

Audio SoundsAndAlerts KeyTones Mode ............................... 59

Audio SoundsAndAlerts RingTone .......................................... 59

Audio SoundsAndAlerts RingVolume...................................... 59

Cameras settings .................................................................. 60

Cameras Camera [1] Backlight ................................................ 60

Cameras Camera [1] Brightness Level .................................... 60

Cameras Camera [1] Brightness Mode ................................... 60

Cameras Camera [1] Focus Mode............................................61

Cameras Camera [1] Gamma Level .........................................61

Cameras Camera [1] Gamma Mode .........................................61

Cameras Camera [1] Mirror ......................................................61

Cameras Camera [1] W hitebalance Level ................................61

Cameras Camera [1] Whitebalance Mode ...............................61

Cameras PowerLine Frequency .............................................. 60

Cameras Preset TriggerAutofocus .......................................... 60

Conference settings ............................................................. 62

Conference [1..1] ActiveControl Mode .................................... 62

Conference [1..1] AutoAnswer Delay ....................................... 62

Conference [1..1] AutoAnswer Mode ...................................... 62

Conference [1..1] AutoAnswer Mute ........................................ 62

Conference [1..1] CallProtocolIPStack ..................................... 62

Conference [1..1] DefaultCall Protocol ..................................... 64

Conference [1..1] DefaultCall Rate ........................................... 64

Conference [1..1] DoNotDisturb DefaultTimeout ..................... 63

Conference [1..1] Encryption Mode ......................................... 63

Conference [1..1] FarEndControl Mode ................................... 63

Conference [1..1] FarEndControl SignalCapability ................... 63

Conference [1..1] IncomingMultisiteCall Mode ........................ 66

Conference [1..1] MaxReceiveCallRate ................................... 64

Conference [1..1] MaxTotalReceiveCallRate ............................ 65

Conference [1..1] MaxTotalTransmitCallRate ........................... 64

Conference [1..1] MaxTransmitCallRate ................................... 64

Conference [1..1] MicUnmuteOnDisconnect Mode ................. 63

Conference [1..1] Multipoint Mode .......................................... 66

Conference [1..1] Presentation OnPlacedOnHold ................... 65

Conference [1..1] Presentation RelayQuality ........................... 65

Conference [1..1] VideoBandwidth MainChannel Weight ........ 65

Conference [1..1] VideoBandwidth Mode ................................ 65

Conference [1..1] VideoBandwidth PresentationChannel Weight

..................................................................................... 65

FacilityService settings ......................................................... 67

FacilityService Service [1..5] CallType .................................... 67

FacilityService Service [1..5] Name ........................................ 67

FacilityService Service [1..5] Number ..................................... 67

FacilityService Service [1..5] Type .......................................... 67

H323 settings ........................................................................ 68

H323 NAT Address ................................................................. 68

H323 NAT Mode ..................................................................... 68

H323 Profile [1..1] Authentication LoginName ......................... 68

H323 Profile [1..1] Authentication Mode .................................. 68

H323 Profile [1..1] Authentication Password ........................... 69

H323 Profile [1..1] CallSetup Mode .......................................... 69

H323 Profile [1..1] Encr yption KeySize ................................... 69

H323 Profile [1..1] Gatekeeper Address .................................. 69

H323 Profile [1..1] Gatekeeper Discover y ................................ 69

H323 Profile [1..1] H323Alias E164 .......................................... 69

H323 Profile [1..1] H323Alias ID ............................................... 70

H323 Profile [1..1] PortAllocation ............................................. 70

Logging settings ....................................................................71

Logging Mode ..........................................................................71

Network settings ................................................................... 72

Network [1..1] DHCP RequestTFTPServerAddress ................. 73

Network [1..1] DNS Domain Name ........................................... 73

Network [1..1] DNS Server [1..3] Address ................................ 73

Network [1..1] IEEE8021X AnonymousIdentity ......................... 76

Network [1..1] IEEE8021X Eap Md5 ......................................... 76

Network [1..1] IEEE8021X Eap Peap ........................................ 77

Network [1..1] IEEE8021X Eap Tls ............................................ 77

Network [1..1] IEEE8021X Eap Ttls ........................................... 77

Network [1..1] IEEE8021X Identity ............................................ 76

Page 57

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Network [1..1] IEEE8021X Mode .............................................. 75

Network [1..1] IEEE8021X Password ........................................ 76

Network [1..1] IEEE8021X TlsVerify .......................................... 76

Network [1..1] IEEE8021X UseClientCertificate ....................... 76

Network [1..1] IPStack .............................................................. 72

Network [1..1] IPv4 Address .................................................... 72

Network [1..1] IPv4 Assignment ............................................... 72

Network [1..1] IPv4 Gateway .................................................... 72

Network [1..1] IPv4 SubnetMask .............................................. 72

Network [1..1] IPv6 Address .................................................... 73

Network [1..1] IPv6 Assignment ............................................... 72

Network [1..1] IPv6 DHCPOptions ........................................... 73

Network [1..1] IPv6 Gateway .................................................... 73

Network [1..1] MTU .................................................................. 77

Network [1..1] QoS Diffserv Audio ............................................ 74

Network [1..1] QoS Diffserv Data .............................................. 74

Network [1..1] QoS Diffserv ICMPv6 ....................................... 75

Network [1..1] QoS Diffserv NTP ............................................. 75

Network [1..1] QoS Diffserv Signalling ..................................... 75

Network [1..1] QoS Diffserv Video ............................................74

Network [1..1] QoS Mode ......................................................... 74

Network [1..1] RemoteAccess Allow ........................................ 78

Network [1..1] Speed ............................................................... 77

Network [1..1] TrafficControl Mode .......................................... 77

Network [1..1] VLAN Voice Mode ............................................ 78

Network [1..1] VLAN Voice VlanId............................................ 78

NetworkServices settings ..................................................... 79

NetworkServices CDP Mode .................................................. 79

NetworkServices CTMS Encryption ....................................... 83

NetworkServices CTMS Mode ............................................... 82

NetworkServices H323 Mode ................................................ 79

NetworkServices HTTP Mode ................................................ 79

NetworkServices HTTPS Mode .............................................. 80

NetworkServices HTTPS OCSP Mode ................................... 80

NetworkServices HTTPS OCSP URL ......................................81

NetworkServices HT TPS VerifyClientCertificate .................... 80

NetworkServices HT TPS VerifyServerCertificate .................. 80

NetworkServices Medianet Metadata .....................................81

NetworkServices MultiWay Address ...................................... 80

NetworkServices MultiWay Protocol ...................................... 80

NetworkServices NTP Address ...............................................81

NetworkServices NTP Mode ...................................................81

NetworkServices SIP Mode .................................................... 79

NetworkServices SNMP CommunityName ............................ 82

NetworkServices SNMP Host [1..3] Address ...........................81

NetworkServices SNMP Mode ................................................81

NetworkServices SNMP SystemContact ............................... 82

NetworkServices SNMP SystemLocation .............................. 82

NetworkServices SSH AllowPublicKey ................................... 82

NetworkServices SSH Mode .................................................. 82

NetworkServices Telnet Mode ............................................... 79

NetworkServices WelcomeText .............................................. 79

NetworkServices XMLAPI Mode ............................................ 79

Peripherals settings .............................................................. 84

Peripherals Pairing CiscoTouchPanels RemotePairing ........... 84

Peripherals Profile TouchPanels ............................................. 84

Phonebook settings .............................................................. 85

Phonebook Server [1..1] ID ...................................................... 85

Phonebook Server [1..1] Type ................................................. 85

Phonebook Server [1..1] URL .................................................. 85

Provisioning settings ............................................................. 86

Provisioning Connectivity ....................................................... 86

Provisioning ExternalManager Address .................................. 87

Provisioning ExternalManager AlternateAddress.................... 87

Provisioning ExternalManager Domain ................................... 87

Provisioning ExternalManager Path ........................................ 87

Provisioning ExternalManager Protocol .................................. 87

Provisioning HttpMethod ........................................................ 86

Provisioning LoginName ......................................................... 86

Provisioning Mode .................................................................. 86

Provisioning Password ............................................................ 86

RTP settings .......................................................................... 88

RTP Ports Range Star t ............................................................ 88

RTP Ports Range Stop ............................................................ 88

Security settings ................................................................... 89

Security Audit Logging Mode ................................................. 89

Security Audit OnError Action ................................................. 89

Security Audit Ser ver Address ............................................... 89

Security Audit Ser ver Port ...................................................... 89

Security Audit Ser ver Port Assignment ................................... 89

Security Session InactivityTimeout ......................................... 90

Security Session ShowLastLogon .......................................... 90

SerialPort settings ................................................................ 91

SerialPort LoginRequired .........................................................91

SerialPort Mode .......................................................................91

SIP settings ........................................................................... 92

SIP ANAT ................................................................................ 92

SIP AuthenticateTransferror .................................................... 92

SIP ListenPort ......................................................................... 92

SIP OCSP DefaultResponder .................................................. 92

SIP OCSP Mode...................................................................... 92

SIP PreferredIPMedia .............................................................. 92

SIP PreferredIPSignaling ......................................................... 92

SIP Profile [1..1] Authentication [1..1] LoginName .................... 94

SIP Profile [1..1] Authentication [1..1] Password ....................... 94

SIP Profile [1..1] DefaultTransport ............................................ 94

SIP Profile [1..1] DisplayName.................................................. 94

SIP Profile [1..1] Ice DefaultCandidate ..................................... 93

SIP Profile [1..1] Ice Mode ........................................................ 93

SIP Profile [1..1] Line ................................................................ 95

SIP Profile [1..1] Mailbox .......................................................... 95

SIP Profile [1..1] Outbound ....................................................... 95

SIP Profile [1..1] Proxy [1..4] Address ....................................... 95

SIP Profile [1..1] Proxy [1..4] Discovery .................................... 95

SIP Profile [1..1] TlsVerify ......................................................... 94

SIP Profile [1..1] Turn BandwidthProbe .................................... 93

SIP Profile [1..1] Turn DiscoverMode ....................................... 93

SIP Profile [1..1] Turn DropRflx ................................................. 93

SIP Profile [1..1] Turn Password ............................................... 94

SIP Profile [1..1] Turn Server .................................................... 93

SIP Profile [1..1] Turn UserName ............................................. 93

SIP Profile [1..1] Type ............................................................... 95

SIP Profile [1..1] URI ................................................................. 94

Standby settings ................................................................... 96

Standby BootAction ................................................................ 96

Standby Control ...................................................................... 96

Standby Delay ......................................................................... 96

Page 58

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Standby StandbyAction .......................................................... 96

Standby WakeupAction ........................................................... 96

SystemUnit settings .............................................................. 97

SystemUnit CallLogging Mode ............................................... 97

SystemUnit ContactInfo Type ................................................. 97

SystemUnit MenuLanguage .................................................... 97

SystemUnit Name ................................................................... 97

Time settings ........................................................................ 98

Time DateFormat .................................................................... 98

Time OlsonZone ..................................................................... 99

Time TimeFormat .................................................................... 98

Time Zone ............................................................................... 98

UserInterface settings ..........................................................101

UserInterface Language ........................................................101

UserInterface OSD EncryptionIndicator .................................101

UserInterface OSD LanguageSelection .................................101

UserInterface OSD LoginRequired.........................................101

UserInterface OSD Output .....................................................101

UserInterface TouchPanel DefaultPanel ............................... 102

UserInterface UserPreferences ............................................ 102

UserInterface Wallpaper ....................................................... 10 2

Video settings ......................................................................103

Video AllowWebSnapshots ................................................... 103

Video CamCtrlPip CallSetup Duration .................................. 103

Video CamCtrlPip CallSetup Mode ....................................... 103

Video Input Connector [1..4] CameraControl CameraId ....... 104

Video Input Connector [1..4] CameraControl Mode .............. 104

Video Input Connector [1..4] InputSourceType ..................... 103

Video Input Connector [1..4] Name ....................................... 10 3

Video Input Connector [1..4] OptimalDefinition Profile .......... 10 5

Video Input Connector [1..4] OptimalDefinition Threshold60fps

..................................................................... 105

Video Input Connector [1..4] Visibility ................................... 104

Video Input Connector [2..4] PresentationSelection ............. 10 5

Video Input Connector [2..4] Quality ..................................... 104

Video Input Connector [2..4] RGBQuantizationRange ........... 10 6

Video Input Connector [2] DviType ....................................... 106

Video Layout DisableDisconnectedLocalOutputs ................. 10 6

Video Layout LocalLayoutFamily .......................................... 106

Video Layout PresentationDefault View .................................107

Video Layout RemoteLayoutFamily ........................................107

Video Layout ScaleToFrame ..................................................107

Video Layout ScaleToFrameThreshold ...................................107

Video Layout Scaling .............................................................107

Video Monitors ...................................................................... 109

Video OSD EncryptionIndicator ............................................ 109

Video OSD LanguageSelection ............................................ 109

Video OSD LoginRequired .................................................... 10 9

Video OSD Output ................................................................ 109

Video Output Connector [1..2] Resolution ..............................111

Video Output Connector [1] Brightness .................................110

Video Output Connector [1] Whitebalance Level ..................11 0

Video Output Connector [2] CEC Mode .................................11 0

Video Output Connector [2] Location HorizontalOffset .........110

Video Output Connector [2] Location VerticalOffset .............111

Video Output Connector [2] OverscanLevel .......................... 110

Video Output Connector [2] RGBQuantizatonRange .............. 111

Video PIP ActiveSpeaker DefaultValue Position ................... 108

Video PIP Presentation DefaultValue Position ...................... 108

Video SelfviewDefault FullscreenMode ................................ 109

Video SelfviewDefault Mode ................................................. 108

Video SelfviewDefault OnMonitorRole .................................. 10 9

Video SelfviewDefault PIPPosition ........................................ 109

Video SelfviewPosition ......................................................... 10 8

Video WallPaper.....................................................................111

Experimental settings .......................................................... 112

Page 59

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Audio settings

Audio Input Microphone [1]

Set the audio input microphone mode.

Requires user role: ADMIN

Value space: <Off/On>

Off: Disable the microphone connector. On: Enable the microphone connector.

Example:

Audio Input Microphone 1 Mode: On

Audio Microphones Mute Enabled

Determine whether audio-mute is allowed or not. The default value is True.

Requires user role: ADMIN

Value space: <True/InCallOnly>

Tru e: Muting of audio is always available. InCallOnly: Muting of audio is only available when the device is in a call. When Idle it is not

possible to mute the microphone. This is useful when an external telephone service/audio system is connected via the codec and is to be available when the codec is not in a call. When set to InCallOnly this will prevent the audio-system from being muted by mistake.

Example:

Audio Microphones Mute Enabled: True

Audio SoundsAndAlerts KeyTones Mode

The system can be configured to make a keyboard click sound effect (key tone) when typing text or numbers on the Touch controller.

Requires user role: USER

Value space: <Off/On>

Off: No key tones will be played when you type. On: You will hear key tones when you type.

Example:

Audio SoundsAnd Alerts KeyTones Mode: Off

Audio SoundsAndAlerts RingTone

This setting defines which ringtone to use for incoming calls. You need to enter the exact name of the ringtone. You can find the available ringtones the following ways.

Web interface: On the Configuration > Personalization page. Touch controller: On the Ringtone & Sound panel of the Settings menu. This panel is either

in the open part of the Settings menu, or included in the password protected Administrator menu. The User Interface UserPreference setting def ines which panels will be in the password protected area.

Requires user role: USER

Value space: <S: 1, 100>

Format: String with a ma ximum of 100 characters.

Example:

Audio SoundsAnd Alerts RingTone: "Sunrise"

Audio SoundsAndAlerts RingVolume

Sets the ring volume for an incoming call.

Requires user role: USER

Value space: <0..100>

Range: The value goes in steps of 5 from 0 to 100 (from -34.5 dB to 15 dB). Volume 0 = Off.

Example:

Audio SoundsAnd Alerts RingVolume: 40

Audio DefaultVolume

Set the default speaker volume. The volume returns to this value when you switch on or restart the video system. Use the Touch controller to change the volume while the video system is running.

Requires user role: USER

Value space: <0..100>

Range: The value must be between 0 and 100. The values from 1 to 100 correspond to the range from -34.5 dB to 15 dB (0.5 dB steps). The value 0 means that the audio is switched off.

Example:

Audio Defau ltVolume: 50

Page 60

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Cameras settings

Cameras PowerLine Frequency

The video system's camera is able to compensate for any flicker noise from the electrical power supply (power line frequency anti-flickering). The camera also supports auto detection of line frequency. Select the Auto option (default), or set this camera configuration based on your power line frequency.

Requires user role: ADMIN

Value space: <Auto/50Hz/60Hz>

Auto: Allow the camera to detect the power frequency automatically. 50Hz: Use this value when the power line frequency is 50 Hz. 60Hz: Use this value when the power line frequency is 60 Hz.

Example:

Cameras PowerLine Frequency: Auto

Cameras Preset TriggerAutofocus

The current position (pan and tilt), zoom and focus are stored with a preset. Use this set ting to determine if the camera should refocus or use the focus value that is stored with the preset.

Requires user role: ADMIN

Value space: <Auto/Off/On>

Auto: Whether the camera refocuses or not when selecting a preset, depends on the camera type.

Off: The focus value that is stored with the preset will be used. The camera will not refocus when selecting a preset.

On: The camera will refocus when selecting a preset. The focus value that is stored with the preset may be overridden.

Example:

Cameras Preset TriggerAutofocus: Auto

Cameras Camera [1] Backlight

This configuration turns backlight compensation on or off. Backlight compensation is useful when there is much light behind the persons in the room. Without compensation the persons will easily appear very dark to the far end.

Requires user role: ADMIN

Value space: <Off/On>

Off: Turn off the camera backlight compensation. On: Turn on the camera backlight compensation.

Example:

Cameras Ca mera 1 Backlight: Off

Cameras Camera [1] Brightness Mode

Set the camera brightnes s mode.

Requires user role: ADMIN

Value space: <Auto/Manual>

Auto: The camera brightness is automatically set by the system. Manual: Enable manual control of the camera brightnes s. The brightness level is set using

the Cameras Camera Brightness Level set ting.

Example:

Cameras Ca mera 1 Brightness Mode: Auto

Cameras Camera [1] Brightness Level

Set the brightness level. Requires the Camera Brightness Mode to be set to Manual.

Requires user role: ADMIN

Value space: <1..31>

Range: Select a value from 1 to 31.

Example:

Cameras Ca mera 1 Brightness Level: 20

Page 61

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Cameras Camera [1] Focus Mode

Set the camera focus mode.

Requires user role: ADMIN

Value space: <Auto/Manual>

Auto: The camera will auto focus once a call is connected, as well as after moving the camera (pan, tilt, zoom). The system will use auto focus only for a few seconds to set the right focus; then auto focus is turned off to prevent continuous focus adjustments of the camera.

Manual: Turn the autofocus off and adjust the camera focus manually.

Example:

Cameras Ca mera 1 Focus Mode: Auto

Cameras Camera [1] Gamma Mode

This setting enables gamma corrections. Gamma describes the nonlinear relationship between image pixels and monitor brightness.

Requires user role: ADMIN

Value space: <Auto/Manual>

Auto: Auto is the default and the recommended setting. Manual: In manual mode the gamma value is changed with the gamma level set ting, ref:

Cameras Camera [1..n] Gamma Level.

Example:

Cameras Ca mera 1 Gamma Mode: Auto

Cameras Camera [1] Gamma Level

By setting the Gamma Level you can select which gamma correction table to use. This setting may be useful in difficult lighting conditions, where changes to the brightness setting does not provide satisfactory results. Requires the Gamma Mode to be set to Manual.

Requires user role: ADMIN

Value space: <0..7>

Range: Select a value from 0 to 7.

Example:

Cameras Ca mera 1 Gamma Level: 0

Cameras Camera [1] Mirror

With Mirror mode (horizontal flip) you can mirror the image on screen.

Requires user role: ADMIN

Value space: <Off/On>

Off: See the self-view in normal mode, that is the experience of self-view is as seeing yourself as other people see you.

On: See the self-view in mirror mode, that is the self-view is reversed and the experience of self-view is as seeing yourself in a mirror.

Example:

Cameras Ca mera 1 Mirror: Auto

Cameras Camera [1] Whitebalance Mode

Set the camera white balance mode.

Requires user role: ADMIN

Value space: <Auto/Manual>

Auto: The camera will continuously adjust the white balance depending on the camera view. Manual: Enables manual control of the camera white balance. The white balance level is set

using the Cameras Camera W hitebalance Level setting.

Example:

Cameras Ca mera 1 Whitebalance Mode: Auto

Cameras Camera [1] Whitebalance Level

Set the white balance level. Requires the Camera Whitebalance Mode to be set to manual.

Requires user role: ADMIN

Value space: <1..16>

Range: Select a value from 1 to 16.

Example:

Cameras Ca mera 1 Whitebalance Level: 1

Page 62

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Conference settings

Conference [1..1] ActiveControl Mode

Active control is a feature that allows conference participants to administer a conference on Cisco TelePresence Server using the video system's interfaces (not available from the TRC5 remote control and on-screen display). Each user can see the participant list, change video layout, disconnect participants, etc. from the interface. The active control feature is enabled by default, provided that it is supported by the infrastructure (Cisco Unified Communications Manager (CUCM) version 9.1.2 or newer, Cisco TelePresence Video Communication Ser ver (VCS) version X8.1 or newer). Change this setting if you want to disable the active control features.

Requires user role: ADMIN

Value space: <Auto/Off>

Auto: Active control is enabled when supported by the infrastructure. Off: Active control is disabled.

Example:

Conference ActiveControl Mode: Auto

Conference [1..1] CallProtocolIPStack

Select if the system should enable IPv4, IP v6, or dual IP stack on the call protocol (SIP, H323).

Requires user role: ADMIN

Value space: <Dual/IPv4/IPv6>

Dual: Enables both IPv4 and IPv6 for the call protocol. IPv4: When set to IPv4, the call protocol will use IPv4. IPv6: When set to IPv6, the call protocol will use IPv6.

Example:

Conference 1 CallProtocolIPStack: Dual

Conference [1..1] AutoAnswer Mode

Set the auto answer mode. Use the Conference AutoA nswer Delay set ting if you want the system to wait a number of seconds before answering the call, and use the Conference AutoAnswer Mute setting if you want your microphone to be muted when the call is answered.

Requires user role: ADMIN

Value space: <Off/On>

Off: You must answer incomming calls manually by tapping Answer on the Touch controller. On: The system automatically answers incoming calls, except if you are already in a call. You

must always answer or decline incoming calls manually when you are already engaged in a call.

Example:

Conference 1 AutoAnswer Mode: Off

Conference [1..1] AutoAnswer Mute

Determine if the microphone shall be muted when an incoming call is automatically answered. Requires that AutoAnswer Mode is switched on.

Requires user role: ADMIN

Value space: <Off/On>

Off: The incoming call will not be muted. On: The incoming call will be muted when automatically answered.

Example:

Conference 1 AutoAnswer Mute: Off

Conference [1..1] AutoAnswer Delay

Define how long (in seconds) an incoming call has to wait before it is answered automatically by the system. Requires that AutoAnswer Mode is switched on.

Requires user role: ADMIN

Value space: <0..50>

Range: Select a value from 0 to 50 seconds.

Example:

Conference 1 AutoAnswer Delay: 0

Page 63

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Conference [1..1] MicUnmuteOnDisconnect Mode

Determine if the microphones shall be unmuted automatically when all calls are disconnected. In a meeting room or other shared resources this may be done to prepare the system for the ne xt u se r.

Requires user role: ADMIN

Value space: <Off/On>

Off: If muted during a call, let the microphones remain muted after the call is disconnected. On: Unmute the microphones after the call is disconnected.

Example:

Conference 1 MicUnmuteOnDisconnect Mode: On

Conference [1..1] DoNotDisturb DefaultTimeout

This setting determines the default duration of a Do Not Disturb session, i.e. the period when incoming calls are rejected and registered as missed calls. The session can be terminated earlier by using the user inter face (Touch controller). The default value is 60 minutes.

Requires user role: ADMIN

Value space: <0..1440>

Range: Select the number of minutes (between 0 and 1440, i.e. 24 hours) before the Do Not Disturb session times out automatically.

Example:

Conference 1 DoNotDisturb DefaultTimeOut: 60

Conference [1..1] FarEndControl Mode

Lets you decide if the remote side (far end) should be allowed to select your video sources and control your local camera (pan, tilt, zoom).

Requires user role: ADMIN

Value space: <Off/On>

Off: The far end is not allowed to select your video sources or to control your local camera (pan, tilt, zoom).

On: Allows the far end to be able to select your video sources and control your local camera (pan, tilt, zoom). You will still be able to control your camera and select your video sources as normal.

Example:

Conference 1 FarEndControl Mode: On

Conference [1..1] FarEndControl SignalCapability

Set the far end control (H.224) signal capabilit y mode.

Requires user role: ADMIN

Value space: <Off/On>

Off: Disable the far end control signal capability. On: Enable the far end control signal capability.

Example:

Conference 1 FarEndControl SignalCapability: On

Conference [1..1] Encryption Mode

Set the conference encryption mode. A padlock with the text "Encryption On" or "Encryption Off" displays on screen for a few seconds when the conference starts.

NOTE: Requires the Encryption Option Key to be installed. When the Encryption Option Key is not installed the encryption mode is set to Off.

Requires user role: ADMIN

Value space: <Off/On/BestEffort>

Off: The system will not use encryption. On: The system will only allow calls that are encrypted. BestEffor t: The system will use encr yption whenever possible. > In Point to point calls: If the far end system suppor ts encryption (AES-128), the call will be

encrypted. If not, the call will proceed without encr yption. > In MultiSite calls: In order to have encr ypted MultiSite conferences, all sites must support

encryption. If not, the conference will be unencrypted.

Example:

Conference 1 Encryption Mode: BestEffort

Page 64

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Conference [1..1] DefaultCall Protocol

Set the Default Call Protocol to be used when placing calls from the system.

Requires user role: ADMIN

Value space: <Auto/H323/Sip/H320>

Auto: Enables auto-selection of the call protocol based on which protocols are available. If multiple protocols are available, the order of priorit y is: 1) SIP; 2) H323; 3) H320. If the system cannot register, or the call protocol is not enabled, the auto-selection chooses H323.

H323: A ll calls are set up as H.323 calls. Sip: All calls are set up as SIP calls. H320: All calls are set up as H.320 calls (only applicable if connected to a Cisco

TelePresence ISDN Link gateway).

Example:

Conference 1 DefaultCall Protocol: Auto

Conference [1..1] DefaultCall Rate

Set the Default Call Rate to be used when placing calls from the system.

Requires user role: ADMIN

Value space: <64..6000>

Range: Select a value between 64 and 6000 k bps.

Example:

Conference 1 DefaultCall Rate: 1920

Conference [1..1] MaxTransmitCallRate

Specify the maximum transmit bit rate to be used when placing or receiving calls. Note that this is the maximum bit rate for each individual call; use the Conference MaxTotalTransmitCallRate setting to set the aggregated maximum for all simultaneous active calls.

Requires user role: ADMIN

Value space: <64..6000>

Range: Select a value between 64 and 6000 k bps.

Example:

Conference 1 MaxTransmitCallRate: 6000

Conference [1..1] MaxReceiveCallRate

Specify the maximum receive bit rate to be used when placing or receiving calls. Note that this is the maximum bit rate for each individual call; use the Conference MaxTotalReceiveCallRate setting to set the aggregated maximum for all simultaneous active calls.

Requires user role: ADMIN

Value space: <64..6000>

Range: Select a value between 64 and 6000 k bps.

Example:

Conference 1 MaxReceiveCallRate: 6000

Conference [1..1] MaxTotalTransmitCallRate

This configuration applies when using a video system's built-in MultiSite feature (optional) to host a multipoint video conference.

Specify the maximum overall transmit bit rate allowed. The bit rate will be divided fairly among all active calls at any time. This means that the individual calls will be up-speeded or downspeeded as appropriate when someone leaves or enters a multipoint conference, or when a call is put on hold (suspended) or resumed.

The maximum transmit bit rate for each individual call is defined in the Conference MaxTransmitCallRate setting.

Requires user role: ADMIN

Value space: <64..10000>

Range: Select a value between 64 and 10000.

Example:

Conference 1 MaxTotalTransm itCallRate: 10000

Page 65

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Conference [1..1] MaxTotalReceiveCallRate

This configuration applies when using a video system's built-in MultiSite feature (optional) to host a multipoint video conference.

Specify the maximum overall receive bit rate allowed. The bit rate will be divided fairly among all active calls at any time. This means that the individual calls will be up-speeded or downspeeded as appropriate when someone leaves or enters a multipoint conference, or when a call is put on hold (suspended) or resumed.

The maximum receive bit rate for each individual call is def ined in the Conference MaxReceiveCallRate setting.

Requires user role: ADMIN

Value space: <64..10000>

Range: Select a value between 64 and 10000.

Example:

Conference 1 MaxTotalReceiveCallRate: 10000

Conference [1..1] VideoBandwidth Mode

Set the conference video bandwidth mode.

Requires user role: ADMIN

Value space: <Dynamic/Static>

Dynamic: The available transmit bandwidth for the video channels are distributed among the currently active channels. If there is no presentation, the main video channels will use the bandwidth of the presentation channel.

Static: The available transmit bandwidth is assigned to each video channel, even if it is not active.

Example:

Conference 1 VideoBandwidth Mode: Dynamic

Conference [1..1] VideoBandwidth MainChannel Weight

The available transmit video bandwidth is distributed on the main channel and presentation channel according to "MainChannel Weight" and "PresentationChannel Weight". If the main channel weight is 2 and the presentation channel weight is 1, then the main channel will use twice as much bandwidth as the presentation channel.

Requires user role: ADMIN

Value space: <1..10>

Range: 1 to 10.

Example:

Conference 1 VideoBandwidth MainChannel Weight: 5

Conference [1..1] VideoBandwidth PresentationChannel Weight

Requires user role: ADMIN

Value space: <1..10>

Range: 1 to 10.

Example:

Conference 1 VideoBandwidth PresentationChannel Weight: 5

Conference [1..1] Presentation RelayQuality

This configuration applies to video systems that are using the built-in MultiSite feature (optional) to host a multipoint video conference. When a remote user shares a presentation, the video system (codec) will transcode the presentation and send it to the other participants in the multipoint conference. The RelayQuality setting specifies whether to give priority to high frame rate or to high resolution for the presentation source.

Requires user role: ADMIN

Value space: <Motion/Sharpness>

Motion: Gives the highest possible frame rate. Used when there is a need for higher frame rates, typically when there is a lot of motion in the picture.

Sharpness: Gives the highest possible resolution. Used when you want the highest quality of detailed images and graphics.

Example:

Conference 1 Presentation RelayQuality: Sharpness

Conference [1..1] Presentation OnPlacedOnHold

Define whether or not to continue sharing a presentation after the remote site has put you on hold.

Requires user role: ADMIN

Value space: <Stop/NoAction>

Stop: The video system stops the presentation sharing when the remote site puts you on hold. The presentation will not continue when the call is resumed.

NoAction: The video system will not stop the presentation sharing when put on hold. The presentation will not be shared while you are on hold, but it will continue automatically when the call is resumed.

Example:

Conference 1 Presentation OnPlacedOnHold: NoAction

Page 66

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Conference [1..1] Multipoint Mode

Define how the video system handles multiparty video conferences. If registered to a Cisco TelePresence Video Communication Ser ver (VCS), the video system

can either use its own built-in MultiSite feature, or it can rely on the MultiWay network solution. MultiWay requires that the video network includes a multipoint control unit (MCU).

If registered to a Cisco Unified Communications Manager (CUCM) version 8.6.2 or newer, the video system can use either the CUCM conference bridge, or the video system's own built-in MultiSite feature. Which one to use is set-up by CUCM.

Both MultiWay and the CUCM conference bridge allows you to set up conferences with many participants. The built-in MultiSite allows up to four participants (yourself included).

Note that the built-in MultiSite is optional and may not be available on all video systems.

Requires user role: ADMIN

Value space: <Auto/Off/MultiSite/MultiWay/CUCMMediaResourceGroupList>

Auto: The multipoint method available will be choosen automatically; if none are available the Multipoint Mode will automatically be set to Off. If both MultiWay and MultiSite are available, the MultiWay service takes priority over the built-in MultiSite.

Off: Multiparty conferences are not allowed. MultiSite: Multipar ty conferences are set up using the built-in MultiSite feature. If MultiSite is

chosen when the MultiSite feature is not available, the Multipoint Mode will automatically be set to Off.

MultiWay: Multiparty conferences are set up using the MultiWay service. If MultiWay is chosen when the MultiWay service is not available, the Multipoint Mode will automatically be set to Off. This may occur when the NetworkServices MultiWay Address setting is empty or not properly set.

CUCMMediaResourceGroupList: Multiparty conferences (ad hoc conferences) are hosted by the CUCM configured conference bridge. This setting is provisioned by CUCM in a CUCM environment and should never be set manually by the user.

Example:

Conference 1 Multipoint Mode: Auto

Conference [1..1] IncomingMultisiteCall Mode

Select whether or not to allow incoming calls when already in a call/conference.

Requires user role: ADMIN

Value space: <Allow/Deny>

Allow: You will be notified when someone calls you while you are already in a call. You can accept the incoming call or not. The ongoing call may be put on hold while answering the incoming call; or you may merge the calls (requires MultiSite or MultiWay suppor t).

Deny: An incoming call will be rejected if you are already in a call. You will not be notified about the incoming call. However, the call will appear as a missed call in the call history list.

Example:

Conference 1 IncomingMultisiteCall Mode: Allow

Page 67

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

FacilityService settings

FacilityService Service [1..5] Type

Up to five different facilit y services can be supported simultaneously. With this setting you can select what kind of ser vices they are. A facility service is not available unless both the FacilityService Service Name and the FacilitySer vice Ser vice Number settings are properly set. Only Facilit yService Service 1 with Type Helpdesk is available on the Touch controller; the other options are available for system integrators using the API (Application Programming Interface) command set.

Requires user role: ADMIN

Value space: <Other/Concierge/Helpdesk/Emergency/Security/Catering/Transportation>

Other: Select this option for services not covered by the other options. Concierge: Select this option for concierge services. Helpdesk: Select this option for helpdesk services. Emergency: Select this option for emergency services. Security: Select this option for security services. Catering: Select this option for catering services. Transportation: Select this option for transportation services.

Example:

FacilityService Service 1 Type: Helpdesk

FacilityService Service [1..5] Name

Enter the name of the facility service. Up to f ive different facility services are suppor ted. A facility service is not available unless both the FacilityService Service Name and the FacilityService Service Number settings are properly set. Only FacilityService Service 1 is available on the Touch controller. The name will show on the facility ser vice call button, which appears when you tap the question mark icon in the top bar. The other services are available for system integrators using the API (Application Programming Interface) command set.

Requires user role: ADMIN

Value space: <S: 0, 1024>

Format: String with a ma ximum of 1024 characters.

Example:

FacilityService Service 1 Name: ""

FacilityService Service [1..5] Number

Enter the number (URI or phone number) of the facilit y service. Up to five dif ferent facility services are suppor ted. A facilit y service is not available unless both the FacilityService Service Name and the FacilityService Service Number settings are properly set. Only FacilitySer vice Service 1 is available on the Touch controller; the other options are available for system integrators using the API (Application Programming Interface) command set.

Requires user role: ADMIN

Value space: <S: 0, 1024>

Format: String with a ma ximum of 1024 characters.

Example:

FacilityService Service 1 Number: ""

FacilityService Service [1..5] CallType

Set the call type for each facility ser vice. Up to five different facility ser vices are supported. A facility service is not available unless both the FacilityService Service Name and the FacilityService Service Number settings are properly set. Only FacilityService Service 1 is available on the Touch controller; the other options are available for system integrators using the API (Application Programming Inter face) command set.

Requires user role: ADMIN

Value space: <Video/Audio>

Video: Select this option for video calls. Aud io: Select this option for audio calls.

Example:

FacilityService Service 1 CallType: Video

Page 68

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

H323 settings

H323 NAT Mode

The firewall traversal technology creates a secure path through the firewall barrier, and enables proper exchange of audio/video data when connected to an external video conferencing system (when the IP traffic goes through a NAT router). NOTE: NAT does not work in conjunction with gatekeepers.

Requires user role: ADMIN

Value space: <Auto/Off/On>

Auto: The system will determine if the H323 NAT Address or the real IP address should be used in signaling. This makes it possible to place calls to endpoints on the L AN as well as endpoints on the WAN. If the H323 NAT Address is wrong or not set, the real IP address will be used.

Off: The system will signal the real IP address. On: The system will signal the configured H323 NAT Address instead of its real IP address

in Q.931 and H.245. The NAT Server Address will be shown in the startup-menu as: "My IP Address: 10.0.2.1". If the H323 NAT Address is wrong or not set, H.323 calls cannot be set up.

Example:

H323 NAT Mode: Off

H323 NAT Address

Enter the external/global IP address to the router with NAT support. Packets sent to the router will then be routed to the system. Note that NAT cannot be used when registered to a gatekeeper.

In the router, the following ports must be routed to the system's IP address: * Port 1720 * Port 5555-6555 * Port 2326-2487

Requires user role: ADMIN

Value space: <S: 0, 64>

Format: A valid IPv4 address or IPv6 address.

Example:

H323 NAT Address: ""

H323 Profile [1..1] Authentication Mode

Set the authenticatin mode for the H.323 profile.

Requires user role: ADMIN

Value space: <Off/On>

Off: If the H.323 Gatekeeper Authentication Mode is set to Off the system will not try to authenticate itself to a H.323 Gatekeeper, but will still tr y a normal registration.

On: If the H.323 Gatekeeper Authentication Mode is set to On and a H.323 Gatekeeper indicates that it requires authentication, the system will try to authenticate itself to the gatekeeper. Requires the Authentication LoginName and Authentication Password to be defined on both the codec and the Gatekeeper.

Example:

H323 Profile 1 Authentication Mode: Off

H323 Profile [1..1] Authentication LoginName

The system sends the Authentication Login Name and the Authentication Password to a H.323 Gatekeeper for authentication. The authentication is a one way authentication from the codec to the H.323 Gatekeeper, i.e. the system is authenticated to the gatekeeper. If the H.323 Gatekeeper indicates that no authentication is required, the system will still try to register. Requires the H.323 Gatekeeper Authentication Mode to be enabled.

Requires user role: ADMIN

Value space: <S: 0, 50>

Format: String with a ma ximum of 50 characters.

Example:

H323 Profile 1 Authentication LoginName: ""

Page 69

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

H323 Profile [1..1] Authentication Password

Requires user role: ADMIN

Value space: <S: 0, 50>

Format: String with a ma ximum of 50 characters.

Example:

H323 Profile 1 Authentication Password: ""

H323 Profile [1..1] CallSetup Mode

The H.323 Call Setup Mode defines whether to use a Gatekeeper or Direct calling when establishing H323 calls.

NOTE: Direct H.323 calls can be made even though the H.323 Call Setup Mode is set to Gatekeeper.

Requires user role: ADMIN

Value space: <Direct/Gatekeeper>

Direct: An IP address must be used when dialing in order to make the H323 call. Gatekeeper: The system will use a Gatekeeper to make a H.323 call. When selecting this

option the H323 Prof ile Gatekeeper Address and H323 Prof ile Gatekeeper Discovery settings must also be configured.

Example:

H323 Profile 1 CallSetup Mode: Gatekeeper

H323 Profile [1..1] Encryption KeySize

Define the minimum or maximum key size for the Dif fie-Hellman key exchange method, which is used when establishing the Advanced Encryption Standard (A ES) encryption key.

Requires user role: ADMIN

Value space: <Min1024bit/Max1024bit/Min2048bit>

Min1024bit: The minimum size is 1024 bit. Ma x1024bi t: The maximum size is 1024 bit. Min2048bit: The minimum size is 2048 bit.

Example:

H323 Profile 1 Encryption MinKeySize: Max1024bit

H323 Profile [1..1] Gatekeeper Discovery

Determine how the system shall register to a H.323 Gatekeeper.

Requires user role: ADMIN

Value space: <Manual/Auto>

Manual: The system will use a specific Gatekeeper identif ied by the Gatekeeper's IP address. Auto: The system will automatically tr y to register to any available Gatekeeper. If a

Gatekeeper responds to the request sent from the codec within 30 seconds this specific Gatekeeper will be used. This requires that the Gatekeeper is in auto discovery mode as well. If no Gatekeeper responds, the system will not use a Gatekeeper for making H.323 calls and hence an IP addres s must be specified manually.

Example:

H323 Profile 1 Gatekeeper Discovery: Manual

H323 Profile [1..1] Gatekeeper Address

Enter the IP address of the Gatekeeper. Requires the H.323 Call Setup Mode to be set to Gatekeeper and the Gatekeeper Discovery to be set to Manual.

Requires user role: ADMIN

Value space: <S: 0, 255>

Format: A valid IPv4 address, IPv6 address or DNS name.

Example:

H323 Profile 1 Gatekeeper Address: "192.0.2.0"

H323 Profile [1..1] H323Alias E164

The H.323 Alias E.164 defines the addres s of the system, according to the numbering plan implemented in the H.323 Gatekeeper. The E.164 alias is equivalent to a telephone number, sometimes combined with access codes.

Requires user role: ADMIN

Value space: <S: 0, 30>

Format: Compact string with a maximum of 30 characters. Valid characters are 0-9, * and #.

Example:

H323 Profile 1 H323Alias E164: "90550092"

Page 70

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

H323 Profile [1..1] H323Alias ID

Lets you specif y the H.323 Alias ID which is used to address the system on a H.323 Gatekeeper and will be displayed in the call lists. Example: "firstname.lastname@company.com", "My H.323 Alias I D"

Requires user role: ADMIN

Value space: <S: 0, 49>

Format: String with a ma ximum of 49 characters.

Example:

H323 Profile 1 H323Alias ID: "firstname.lastname@company.com"

H323 Profile [1..1] PortAllocation

The H.323 Port Allocation setting affects the H.245 por t numbers used for H.323 call signaling.

Requires user role: ADMIN

Value space: <Dynamic/Static>

Dynamic: The system will allocate which ports to use when opening a TCP connection. The reason for doing this is to avoid using the same ports for subsequent calls, as some firewalls consider this as a sign of attack. When Dynamic is selected, the H.323 ports used are from 11000 to 20999. Once 20999 is reached they restart again at 11000. The ports are automatically selected by the system within the given range. Firewall administrators should not try to deduce which por ts are used when, as the allocation schema within the mentioned range may change without any further notice.

Static: When set to Static the ports are given within a static predef ined range [5555-6555].

Example:

H323 Profile 1 PortAllocation: Dynamic

Page 71

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Logging settings

Logging Mode

Not applicable in this version.

Page 72

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Network settings

Network [1..1] IPStack

Select if the system should use IPv4, IPv6, or dual IP stack, on the network interface. NOTE: After changing this setting you may have to wait up to 30 seconds before it takes effect.

Requires user role: ADMIN

Value space: <Dual/IPv4/IPv6>

Dual: When set to Dual, the net work interface can operate on both IP versions at the same time, and can have both an IPv4 and an IPv6 address at the same time.

IPv4: When set to IPv4, the system will use IPv4 on the network interface. IPv6: When set to IPv6, the system will use IPv6 on the network interface.

Example:

Network 1 IPStack: Dual

Network [1..1] IPv4 Assignment

Define how the system will obtain its IPv4 address, subnet mask and gateway address. This setting only applies to systems on IPv4 networks.

Requires user role: ADMIN

Value space: <Static/DHCP>

Static: The addresses must be configured manually using the Network IPv4 Address, Network IPv4 Gateway and Network IPv4 SubnetMask settings (static addresses).

DHCP: The system addresses are automatically assigned by the DHCP server.

Example:

Network 1 IPv4 Assignment: DHCP

Network [1..1] IPv4 Address

Enter the static IPv4 network address for the system. This set ting is only applicable when Network Assignment is set to Static.

Requires user role: ADMIN

Value space: <S: 0, 64>

Format: A valid IPv4 address.

Example:

Network 1 IPv4 Address: "192.0.2.2"

Network [1..1] IPv4 Gateway

Define the IPv4 network gateway. This setting is only applicable when the Network Assignment is set to Static.

Requires user role: ADMIN

Value space: <S: 0, 64>

Format: A valid IPv4 address.

Example:

Network 1 IPv4 Gateway: "192.0.2.1"

Network [1..1] IPv4 SubnetMask

Define the IPv4 network subnet mask. This setting is only applicable when the Network Assignment is set to Static.

Requires user role: ADMIN

Value space: <S: 0, 64>

Format: The valid IPv4 address format.

Example:

Network 1 IPv4 SubnetMask: "255.255.255.0"

Network [1..1] IPv6 Assignment

Define how the system will obtain its IPv6 address and the default gateway address. This setting only applies to systems on IPv6 networks.

Requires user role: ADMIN

Value space: <Static/DHCPv6/Autoconf>

Static: The codec and gateway IP addresses must be configured manually using the Network IPv6 Address and Network IPv6 Gateway settings. The options, for example NTP and DNS server addresses, must either be set manually or obtained from a DHCPv6 ser ver. The Network IPv6 DHCPOptions setting determines which method to use.

DHC Pv 6: All IPv6 addresses, including options, will be obtained from a DHCPv6 server. See RFC 3315 for a detailed description. The Network IPv6 DHCPOptions setting will be ignored.

Autoconf: Enable IPv6 stateless autoconfiguration of the IPv6 network interface. See RFC 4862 for a detailed description. The options, for example NTP and DNS server addresses, must either be set manually or obtained from a DHCPv6 server. The Network IPv6 DHCPOptions setting determines which method to use.

Example:

Network 1 IPv6 Assignment: Autoconf

Page 73

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Network [1..1] IPv6 Address

Enter the static IPv6 network address for the system. This setting is only applicable when the Network IPv6 Assignment is set to Static.

Requires user role: ADMIN

Value space: <S: 0, 64>

Format: A valid IPv6 address.

Example:

Network 1 IP v6 A dd ress: "2001:0DB8:0000:0000:0000:0000:0000:0002"

Network [1..1] IPv6 Gateway

Define the IPv6 network gateway address. This setting is only applicable when the Network IPv6 Assignment is set to Static.

Requires user role: ADMIN

Value space: <S: 0, 64>

Format: A valid IPv6 address.

Example:

Network 1 IP v6 Gateway: "2001:0DB8:0000:0000:0000:0000:0000:0001"

Network [1..1] IPv6 DHCPOptions

Retrieve a set of DHCP options, for example NTP and DNS server addresses, from a DHCPv6 server.

Requires user role: ADMIN

Value space: <Off/On>

Off: Disable the retrieval of DHCP options from a DHCP v6 server. On: Enable the retrieval of a selected set of DHCP options from a DHCPv6 server.

Example:

Network 1 IPv6 DHCPOptions: On

Network [1..1] DHCP RequestTFTPServerAddress

This setting is used only for video systems that are registered to a Cisco Unif ied Communications Manager (CUCM).

The setting determines whether the endpoint should ask the DHCP server for DHCP option 150, so that it can discover the address of the TFTP server (provisioning server) automatically.

If this setting is Off or the DHCP ser ver does not support option 150, the TFTP server address must be set manually using the Provisioning ExternalManager Address setting.

If the Network VLAN Voice Mode setting is Auto and the Cisco Discovery Protocol (CDP) assigns an ID to the voice VLAN, then a request for option 150 will always be sent. That is, the Network DHCP RequestTFTFServerAddress setting will be ignored.

Requires user role: ADMIN

Value space: <Off/On>

Off: The video system will not send a request for DHCP option 150 and the address of the TFTP ser ver must be set manually. See the note above for any exception to this rule.

On: The video system will send a request for option 150 to the DHCP server so that it can automatically discover the address of the TFTP ser ver.

Example:

Network 1 DHCP RequestTFTPServerAddress: On

Network [1..1] DNS Domain Name

DNS Domain Name is the default domain name suffix which is added to unqualified names. Example: If the DNS Domain Name is "company.com" and the name to lookup is

"MyVideoSystem", this will result in the DNS lookup "MyVideoSystem.company.com".

Requires user role: ADMIN

Value space: <S: 0, 64>

Format: String with a ma ximum of 64 characters.

Example:

Network 1 DNS Domain Name: ""

Network [1..1] DNS Server [1..3] Address

Define the network addresses for DNS servers. Up to 3 addresses may be specified. If the network addresses are unknown, contact your administrator or Inter net Service Provider.

Requires user role: ADMIN

Value space: <S: 0, 64>

Format: A valid IPv4 address or IPv6 address.

Example:

Network 1 DNS Server 1 Address: ""

Page 74

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Network [1..1] QoS Mode

The QoS (Quality of Service) is a method which handles the priority of audio, video and data in the network. The QoS set tings must be suppor ted by the infrastructure. Diffser v (Differentiated Services) is a computer networking architecture that specifies a simple, scalable and coarsegrained mechanism for clas sifying, managing net work traf fic and providing QoS pr iorities on modern IP networks.

Requires user role: ADMIN

Value space: <Off/Diffserv>

Off: No QoS method is used. Diffserv: When you set the QoS Mode to Diffserv, the Network QoS Diffserv Audio, Network

QoS Diffserv Video, Network QoS Diffserv Data, Network QoS Diffserv Signalling, Network QoS Diffserv ICMPv6 and Network QoS Diffser v NTP settings are used to prioritize packets.

Example:

Network 1 QoS Mode: Diffserv

Network [1..1] QoS Diffserv Audio

This setting will only take effect if Network QoS Mode is set to Diff serv. Define which priorit y Audio packets should have in the IP network. The priority for the packets ranges from 0 to 63 - the higher the number, the higher the priorit y.

The recommended class for Audio is CS4, which equals the decimal value 32. If in doubt, contact your network administrator.

The priority set here might be overridden when packets are leaving the network controlled by the local net work administrator.

Requires user role: ADMIN

Value space: <0..63>

Range: Select a value between 0 to 63 - the higher the number, the higher the priority. The default value is 0 (best effort).

Example:

Network 1 QoS Diffserv Audio: 0

Network [1..1] QoS Diffserv Video

This setting will only take effect if Network QoS Mode is set to Diff serv. Define which priorit y Video packets should have in the IP network. The packets on the

presentation channel (shared content) are also in the Video packet category. The priority for the packets ranges from 0 to 63 - the higher the number, the higher the priority. The recommended class for Video is CS4, which equals the decimal value 32. If in doubt, contact your network administrator.

The priority set here might be overridden when packets are leaving the network controlled by the local net work administrator.

Requires user role: ADMIN

Value space: <0..63>

Range: Select a value between 0 to 63 - the higher the number, the higher the priority. The default value is 0 (best effort).

Example:

Network 1 QoS Diffserv Video: 0

Network [1..1] QoS Diffserv Data

This setting will only take effect if Network QoS Mode is set to Diff serv. Define which priorit y Data packets should have in the IP network. The priority for the packets ranges from 0 to 63 - the higher the number, the higher the priorit y.

The recommended value for Data is 0, which means best effor t. If in doubt, contact your network administrator.

The priority set here might be overridden when packets are leaving the network controlled by the local net work administrator.

Requires user role: ADMIN

Value space: <0..63>

Range: Select a value between 0 to 63 - the higher the number, the higher the priority. The default value is 0 (best effort).

Example:

Network 1 QoS Diffserv Data: 0

Page 75

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Network [1..1] QoS Diffserv Signalling

This setting will only take effect if Network QoS Mode is set to Diff serv. Define which priorit y Signalling packets that are deemed critical (time-sensitive) for the real-

time operation should have in the IP network. The priority for the packets ranges from 0 to 63 - the higher the number, the higher the priorit y.

The recommended class for Signalling is C S3, which equals the decimal value 24. If in doubt, contact your network administrator.

The priority set here might be overridden when packets are leaving the network controlled by the local net work administrator.

Requires user role: ADMIN

Value space: <0..63>

Range: Select a value between 0 to 63 - the higher the number, the higher the priority. The default value is 0 (best effort).

Example:

Network 1 QoS Diffserv Signalling: 0

Network [1..1] QoS Diffserv ICMPv6

This setting will only take effect if Network QoS Mode is set to Diff serv. Define which priorit y ICMPv6 packets should have in the IP network. The priority for the packets ranges from 0 to 63 - the higher the number, the higher the priorit y.

The recommended value for ICMPv6 is 0, which means best effort. If in doubt, contact your network administrator.

The priority set here might be overridden when packets are leaving the network controlled by the local net work administrator.

Requires user role: ADMIN

Value space: <0..63>

Range: Select a value between 0 to 63 - the higher the number, the higher the priority. The default value is 0 (best effort).

Example:

Network 1 QoS Diffserv ICMPv6: 0

Network [1..1] QoS Diffserv NTP

This setting will only take effect if Network QoS Mode is set to Diff serv. Define which priorit y NTP packets should have in the IP network. The priority for the packets ranges from 0 to 63 - the higher the number, the higher the priorit y.

The recommended value for N TP is 0, which means best effort. If in doubt, contact your network administrator.

The priority set here might be overridden when packets are leaving the network controlled by the local net work administrator.

Requires user role: ADMIN

Value space: <0..63>

Range: Select a value between 0 to 63 - the higher the number, the higher the priority. The default value is 0 (best effort).

Example:

Network 1 QoS Diffserv NTP: 0

Network [1..1] IEEE8021X Mode

The system can be connected to an IEEE 802.1X L AN network, with a port-based network access control that is used to provide authenticated net work acces s for Ethernet net works.

Requires user role: ADMIN

Value space: <Off/On>

Off: The 802.1X authentication is disabled (default). On: The 802.1X authentication is enabled.

Example:

Network 1 IEEE8021X Mode: Off

Page 76

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Network [1..1] IEEE8021X TlsVerify

Verification of the server-side certificate of an IEEE802.1x connection against the certificates in the local CA-list when TLS is used. The CA-list must be uploaded to the video system. This can be done from the web interface.

This setting takes effect only when Net work [1..1] IEEE8021X Eap Tls is enabled (On).

Requires user role: ADMIN

Value space: <Off/On>

Off: When set to Off, TLS connections are allowed without verifying the server-side X.509 certif icate against the local CA-list. This should typically be selected if no CA-list has been uploaded to the codec.

On: When set to On, the ser ver-side X.509 certificate will be validated against the local CAlist for all TLS connections. Only servers with a valid certificate will be allowed.

Example:

Network 1 IEEE8021X TlsVerify: Off

Network [1..1] IEEE8021X UseClientCertificate

Authentication using a private key/certificate pair during an IEEE802.1x connection. The authentication X.509 cer tificate must be uploaded to the video system. This can be done from the web interface.

Requires user role: ADMIN

Value space: <Off/On>

Off: When set to Off client-side authentication is not used (only ser ver-side). On: When set to On the client (video system) will per form a mutual authentication TLS

handshake with the server.

Example:

Network 1 IEEE8021X UseClientCertificate: Off

Network [1..1] IEEE8021X Identity

The 802.1X Identity is the user name needed for 802.1X authentication.

Requires user role: ADMIN

Value space: <S: 0, 64>

Format: String with a ma ximum of 64 characters.

Example:

Network 1 IEEE8021X Identity: ""

Network [1..1] IEEE8021X Password

The 802.1X Password is the password needed for 802.1X authentication.

Requires user role: ADMIN

Value space: <S: 0, 32>

Format: String with a ma ximum of 32 characters.

Example:

Network 1 IEEE8021X Password: ""

Network [1..1] IEEE8021X AnonymousIdentity

The 802.1X Anonymous ID string is to be used as unencr ypted identity with EAP (Extensible Authentication Protocol) types that support dif ferent tunneled identit y, like EAP-PEAP and EAPTTLS. If set, the anonymous ID will be used for the initial (unencrypted) EAP Identit y Request.

Requires user role: ADMIN

Value space: <S: 0, 64>

Format: String with a ma ximum of 64 characters.

Example:

Network 1 IEEE8021X AnonymousIdentity: ""

Network [1..1] IEEE8021X Eap Md5

Set the Md5 (Message-Digest Algorithm 5) mode. This is a Challenge Handshake Authentication Protocol that relies on a shared secret. Md5 is a Weak securit y.

Requires user role: ADMIN

Value space: <Off/On>

Off: The E AP-MD5 protocol is disabled. On: The EAP-MD5 protocol is enabled (default).

Example:

Network 1 IEEE8021X Eap Md5: On

Page 77

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Network [1..1] IEEE8021X Eap Ttls

Set the TTLS (Tunneled Transport Layer Security) mode. Authenticates LAN clients without the need for client certificates. Developed by Funk Software and Cer ticom. Usually suppor ted by Agere Systems, Proxim and Avaya.

Requires user role: ADMIN

Value space: <Off/On>

Off: The E AP-TTLS protocol is disabled. On: The EAP-TTLS protocol is enabled (default).

Example:

Network 1 IEEE8021X Eap Ttls: On

Network [1..1] IEEE8021X Eap Tls

Enable or disable the use of E AP-TLS (Transport Layer Security) for IEEE802.1x connections. The EAP-TLS protocol, defined in RFC 5216, is considered one of the most secure EAP standards. LAN clients are authenticated using client certificates.

Requires user role: ADMIN

Value space: <Off/On>

Off: The E AP-TLS protocol is disabled. On: The EAP-TLS protocol is enabled (default).

Example:

Network 1 IEEE8021X Eap Tls: On

Network [1..1] IEEE8021X Eap Peap

Set the Peap (Protected Extensible Authentication Protocol) mode. Authenticates LAN clients without the need for client certificates. Developed by Microsof t, Cisco and RSA Security.

Requires user role: ADMIN

Value space: <Off/On>

Off: The E AP-PEAP protocol is disabled. On: The EAP-PEAP protocol is enabled (default).

Example:

Network 1 IEEE8021X Eap Peap: On

Network [1..1] MTU

Set the Ethernet MTU (Maximum Transmission Unit).

Requires user role: ADMIN

Value space: <57 6..1500>

Range: Select a value from 576 to 1500 bytes.

Example:

Network 1 MTU: 1500

Network [1..1] Speed

Set the Ethernet link speed.

Requires user role: ADMIN

Value space: <Aut o/10 ha lf/10f ul l/10 0h al f/10 0f ul l/1000f ul l>

Auto: Autonegotiate link speed. 10h al f: Force link to 10 Mbps half-duplex. 10f ul l: Force link to 10 Mbps full-duplex. 100 ha lf : Force link to 100 Mbps half-duplex. 100 fu ll : Force link to 100 Mbps full-duplex. 1000full: Force link to 1 Gbps full-duplex.

Example:

Network 1 Speed: Auto

Network [1..1] TrafficControl Mode

Set the network traffic control mode to decide how to control the video packets transmission speed.

Requires user role: ADMIN

Value space: <Off/On>

Off: Transmit video packets at link speed. On: Transmit video packets at maximum 20 Mbps. Can be used to smooth out bursts in the

outgoing net work traffic.

Example:

Network 1 TrafficControl: On

Page 78

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Network [1..1] RemoteAccess Allow

Define which IP addresses (IPv4/IPv6) are allowed for remote access to the codec from SSH/ Telnet/HTTP/HT TPS. Multiple IP addresses are separated by a white space.

A network mask (IP range) is specif ied by <ip address>/N, where N is 1-32 for IPv4, and N is 1-128 for IPv6. The /N is a common indication of a network mask where the first N bits are set. Thus 192.168.0.0/24 would match any address starting with 192.168.0, since these are the first 24 bits in the address.

Requires user role: ADMIN

Value space: <S: 0, 255>

Format: String with a ma ximum of 255 characters.

Example:

Network 1 Rem oteAcc ess Allow: "10.11.2.3 192.168.0.0/24 2001:0d b8:0000:0000:0

000:ff00:0042:8329 2001:db8:abcd:0012::0/64"

Network [1..1] VLAN Voice Mode

Set the VLAN voice mode. The VLAN Voice Mode will be set to Auto automatically if you have Cisco UCM (Cisco Unified Communications Manager) as provisioning infrastructure. Note that Auto mode will NOT work if the NetworkSer vices CDP Mode setting is Off.

Requires user role: ADMIN

Value space: <Auto/Manual/Off>

Auto: The Cisco Discover y Protocol (CDP), if available, assigns an id to the voice VLAN. If CDP is not available, VLAN is not enabled.

Manual: The VLAN ID is set manually using the Network VLAN Voice VlanId setting. If CDP is available, the manually set value will be overruled by the value assigned by CDP.

Off: VLAN is not enabled.

Example:

Network 1 VLAN Voice Mode: Auto

Network [1..1] VLAN Voice VlanId

Set the VLAN voice ID. This set ting will only take effect if VLAN Voice Mode is set to Manual.

Requires user role: ADMIN

Value space: <1..40 94 >

Range: Select a value from 1 to 4094.

Example:

Network 1 VLAN Voice VlanId: 1

Page 79

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

NetworkServices settings

NetworkServices CDP Mode

Enable or disable the CDP (Cisco Discovery Protocol) daemon. Enabling CDP will make the endpoint report certain statistics and device identifiers to a CDP-enabled switch. If CDP is disabled, the Network V LAN Voice Mode: Auto setting will not work.

Requires user role: ADMIN

Value space: <Off/On>

Off: The CDP daemon is disabled. On: The CDP daemon is enabled.

Example:

NetworkServices CDP Mode: On

NetworkServices H323 Mode

Determine whether the system should be able to place and receive H.323 calls or not.

Requires user role: ADMIN

Value space: <Off/On>

Off: Disable the possibility to place and receive H.323 calls. On: Enable the possibility to place and receive H.323 calls (default).

Example:

NetworkServices H323 Mode: On

NetworkServices HTTP Mode

Set the HTTP mode to enable/disable access to the system through a web browser. The web interface is used for system management, call management such as call transfer, diagnostic s and software uploads.

Requires user role: ADMIN

Value space: <Off/On>

Off: The HTTP protocol is disabled. On: The HTTP protocol is enabled.

Example:

NetworkServices HTTP Mode: On

NetworkServices SIP Mode

Determine whether the system should be able to place and receive SIP calls or not.

Requires user role: ADMIN

Value space: <Off/On>

Off: Disable the possibility to place and receive SIP calls. On: Enable the possibility to place and receive S IP calls (default).

Example:

NetworkServices SIP Mode: On

NetworkServices Telnet Mode

Telnet is a network protocol used on the Internet or Local A rea Network (LAN) connections.

Requires user role: ADMIN

Value space: <Off/On>

Off: The Telnet protocol is disabled. This is the factory setting. On: The Telnet protocol is enabled.

Example:

NetworkServices Telnet Mode: Off

NetworkServices WelcomeText

Choose which information the user should see when logging on to the codec through Telnet/ SSH.

Requires user role: ADMIN

Value space: <Off/On>

Off: The welcome text is: Login successful On: The welcome text is: Welcome to <system name>; Software version; Software release

date; Login successful.

Example:

NetworkServices WelcomeText: On

NetworkServices XMLAPI Mode

Not applicable in this version.

Page 80

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

NetworkServices MultiWay Address

The MultiWay address must be equal to the Conference Factor y Alias, as configured on the Video Communication Server. The Multi Way™ conferencing enables video endpoint users to introduce a 3rd party into an existing call.

MultiWay™ can be used in the following situations:

1) When you want to add someone else in to your existing call.

2) When you are called by a 3rd party while already in a call and you want to include that person in the call.

Requirements: Video Communication Server (VCS) version X5 (or later) and Codian MCU version 3.1 (or later). Video systems invited to join the MultiWay™ conference must support the H.323 routeToMC facility message if in an H.323 call, or SIP REFER message if in a SIP call.

Requires user role: ADMIN

Value space: <S: 0, 255>

Format: String with a ma ximum of 255 characters (a valid dial URI).

Example:

NetworkServices MultiWay Address: "h323:multiway@company.com"

NetworkServices MultiWay Protocol

Determine the protocol to be used for MultiWay calls.

Requires user role: ADMIN

Value space: <Auto/H323/Sip>

Auto: The system will select the protocol for MultiWay calls. H323: The H323 protocol will be used for MultiWay calls. Sip: The SIP protocol will be used for MultiWay calls.

Example:

NetworkServices MultiWay Protocol: Auto

NetworkServices HTTPS Mode

HTTPS is a web protocol that encrypts and decrypts user page requests as well as the pages that are returned by the web ser ver.

Requires user role: ADMIN

Value space: <Off/On>

Off: The HTTPS protocol is disabled. On: The HTTPS protocol is enabled.

Example:

NetworkServices HTTPS Mode: On

NetworkServices HTTPS VerifyServerCertificate

When the video system connects to an external HTTPS server (like a phone book ser ver or an external manager), this server will present a cer tificate to the video system to identify itself.

Requires user role: ADMIN

Value space: <Off/On>

Off: Do not verify ser ver certificates. On: Requires the system to verify that the server certificate is signed by a trusted Cer tificate

Authorit y (CA). This requires that a list of trusted CAs are uploaded to the system in advance.

Example:

NetworkServices HTTPS VerifyServerCertificate: Off

NetworkServices HTTPS VerifyClientCertificate

When the video system connects to a HTTPS client (like a web browser), the client can be asked to present a certificate to the video system to identif y itself.

Requires user role: ADMIN

Value space: <Off/On>

Off: Do not verify client certificates. On: Requires the client to present a certificate that is signed by a trusted Certificate

Authorit y (CA). This requires that a list of trusted CAs are uploaded to the system in advance.

Example:

NetworkServices HTTPS VerifyClientCertificate: Off

NetworkServices HTTPS OCSP Mode

Define the support for OCSP (Online Certificate Status Protocol) responder services. The OCSP feature allows users to enable OCSP instead of certificate revocation lists (CRLs) to check the certificate status.

For any outgoing H TTPS connection, the OCSP responder is queried of the status. If the corresponding certificate has been revoked, then the HTTPS connection will not be used.

Requires user role: ADMIN

Value space: <Off/On>

Off: Disable OCSP support. On: Enable OCSP support.

Example:

NetworkServices HTTPS OCSP Mode: Off

Page 81

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

NetworkServices HTTPS OCSP URL

Specify the URL of the OCSP responder (server) that will be used to check the certif icate status.

Requires user role: ADMIN

Value space: <S: 0, 255>

Format: String with a ma ximum of 255 characters.

Example:

NetworkServices HTTPS OCSP URL: "http://ocspserver.company.com:81"

NetworkServices Medianet Metadata

Switch On or Off the capability to tag media flows with metadata related to the Cisco Medianet deployment.

Requires user role: ADMIN

Value space: <Off/On>

Off: Media flows will not be tagged with such metadata. On: Media flows will be tagged with such metadata.

Example:

NetworkServices Medianet Metad ata: Off

NetworkServices NTP Mode

The Network Time Protocol (NTP) is used to synchronize the time of the system to a reference time server. The time server will subsequently be queried every 24th hour for time updates. The time will be displayed on the top of the screen. The system will use the time to timestamp messages transmitted to Gatekeepers or Border Controllers requiring H.235 authentication. The system will use the time to timestamp messages transmitted to Gatekeepers or Border Controller s that requires H.235 authentication. It is also used for timestamping Placed Calls, Missed Calls and Received Calls.

Requires user role: ADMIN

Value space: <Auto/Off/Manual>

Auto: The system will use the NTP server, by which address is supplied from the DHCP server in the network. If no DHCP ser ver is used, or the DHCP ser ver does not provide the system with a NTP server address, the system will use the static def ined NTP server address specified by the user.

Off: The system will not use an NTP server. Manual: The system will always use the static defined NTP server address specified by the

us er.

Example:

NetworkServices NTP Mode: Auto

NetworkServices NTP Address

Enter the NTP Address to define the network time protocol server address. This address will be used if NTP Mode is set to Manual, or if set to Auto and no address is supplied by a DHCP server.

Requires user role: ADMIN

Value space: <S: 0, 64>

Format: A valid IPv4 address, IPv6 address or DNS name.

Example:

NetworkServices NTP Address: "0.ta nd berg.pool.ntp.org"

NetworkServices SNMP Mode

SNMP (Simple Net work Management Protocol) is used in network management systems to monitor network-attached devices (routers, servers, switches, projectors, etc) for conditions that warrant administrative attention. SNMP exposes management data in the form of variables on the managed systems, which describe the system configuration. These variables can then be queried (set to ReadOnly) and sometimes set (set to ReadWrite) by managing applications.

Requires user role: ADMIN

Value space: <Off/ReadOnly/ReadWrite>

Off: Disable the SNMP network ser vice. ReadOnly: Enable the SNMP network service for queries only. ReadWrite: Enable the SNMP network service for both queries and commands.

Example:

NetworkServices SNMP Mode: ReadOnly

NetworkServices SNMP Host [1..3] Address

Enter the addres s of up to three SNMP Managers. The system's SNMP Agent (in the codec) responds to requests from SNMP Managers (a PC

program etc.), for example about system location and system contact. SNMP traps are not suppor ted.

Requires user role: ADMIN

Value space: <S: 0, 64>

Format: A valid IPv4 address, IPv6 address or DNS name.

Example:

NetworkServices SNMP Host 1 Address: ""

Page 82

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

NetworkServices SNMP CommunityName

Enter the name of the Network Services SNMP Community. SNMP Community names are used to authenticate SNMP requests. SNMP requests must have a password (case sensitive) in order to receive a response from the SNMP Agent in the codec. The default password is "public". If you have the Cisco TelePresence Management Suite (TMS) you must make sure the same SNMP Community is configured there too. NOTE: The SNMP Communit y password is case sensitive.

Requires user role: ADMIN

Value space: <S: 0, 50>

Format: String with a ma ximum of 50 characters.

Example:

NetworkServices SNMP CommunityName: "public"

NetworkServices SNMP SystemContact

Enter the name of the Network Services SNMP System Contact.

Requires user role: ADMIN

Value space: <S: 0, 50>

Format: String with a ma ximum of 50 characters.

Example:

NetworkServices SNMP SystemContact: ""

NetworkServices SNMP SystemLocation

Enter the name of the Network Services SNMP System Location.

Requires user role: ADMIN

Value space: <S: 0, 50>

Format: String with a ma ximum of 50 characters.

Example:

NetworkServices SNMP SystemLocation: ""

NetworkServices SSH Mode

SSH (or Secure Shell) protocol can provide secure encr ypted communication between the codec and your local computer.

Requires user role: ADMIN

Value space: <Off/On>

Off: The SSH protocol is disabled. On: The SSH protocol is enabled.

Example:

NetworkServices SSH Mode: On

NetworkServices SSH AllowPublicKey

Secure Shell (SSH) public key authentication can be used to access the codec.

Requires user role: ADMIN

Value space: <Off/On>

Off: The SSH public key is not allowed. On: The SSH public key is allowed.

Example:

NetworkServices SSH AllowPu blicKey: On

NetworkServices CTMS Mode

This setting determines whether or not to allow multipar ty conferences controlled by a Cisco TelePresence Multipoint Switch (CTMS).

Video systems are able to initiate or join non-encr ypted multiparty conferences controlled by CTMS version 1.8 or later. Encrypted conferences are supported as from software versions CTMS 1.9.1. Encryption is addressed in the NetworkServices CTMS Encryption setting.

Requires user role: ADMIN

Value space: <Off/On>

Off: Multiparty conferencing via CTMS is prohibited. On: Multipart y conferencing via CTMS is allowed.

Example:

NetworkServices CTMS Mode: On

Page 83

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

NetworkServices CTMS Encryption

This setting indicates whether or not the video system supports encryption when par ticipating in a multipar ty meeting controlled by a Cisco TelePresence Multipoint Switch (CTMS).

CTMS allows three securit y settings for meetings: non-secure (not encrypted), best effort (encrypted if all participants suppor t encryption, other wise not encrypted) and secure (always enc rypted).

Requires user role: ADMIN

Value space: <Off/BestEffort>

Off: The video system does not allow encr yption and therefore cannot participate in a secure CTMS meeting (encr ypted). When par ticipating in a best effor t CTMS meeting, the meeting will be downgraded to non-secure (not encrypted).

BestEffor t: The video system can negotiate encryption parameters with CTMS and participate in a secure CTMS meeting (encrypted). Do not use this value if the CTMS version is older than 1.9.1.

Example:

NetworkServices CTMS Encryption: Off

Page 84

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Peripherals settings

Peripherals Pairing CiscoTouchPanels RemotePairing

In order to use Cisco Touch 10 (touch panel) as user interface for the video system, Touch 10 must be either directly connected to the video system or paired to the video system via LAN. The latter is referred to as remote pairing.

Remote pairing is allowed by default; you must switch this setting Off if you want to prevent remote pairing.

Requires user role: ADMIN

Value space: <Off/On>

Off: Remote pairing of Touch 10 is not allowed. On: Remote pairing of Touch 10 is allowed.

Example:

Peripherals Pairing CiscoTouchPanels RemotePairing: On

Peripherals Profile TouchPanels

Set the number of touch panels that are expected to be connected to the video system. This information is used by the video system’s diagnostics service. If the number of connected touch panels does not match this set ting, the diagnostics service will report it as an inconsistency. Note that only one Cisco Touch controller is suppor ted in this version.

Requires user role: ADMIN

Value space: <No tS et/ Min imu m1/0 /1/ 2/ 3/4 /5>

NotSet: No touch panel check is per formed. Minimum1: At least one touch panel should be connected to the video system. 0-5: This number of Touch controllers should be connected to the video system.

Example:

Peripherals Profile TouchPanels: Minimum1

Page 85

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Phonebook settings

Phonebook Server [1..1] ID

Enter a name for the external phone book.

Requires user role: ADMIN

Value space: <S: 0, 64>

Format: String with a ma ximum of 64 characters.

Example:

Phonebook Server 1 ID: ""

Phonebook Server [1..1] Type

Select the phonebook server type.

Requires user role: ADMIN

Value space: <VCS/TMS/Callway/CUCM>

VCS: Select VCS if the phonebook is located on the Cisco TelePresence Video Communication Server.

TMS: Select TMS if the phonebook is located on the Cisco TelePresence Management Suite server.

Callway: Select Callway if the phonebook is to be provided by the WebEx TelePresence subscription service (formerly called CallWay). Contact your WebEx TelePresence provider for more information.

CUCM: Select CUCM if the phonebook is located on the Cisco Unified Communications Manager.

Example:

Phonebook Server 1 Type: TMS

Phonebook Server [1..1] URL

Enter the addres s (URL) to the external phone book server.

Requires user role: ADMIN

Value space: <S: 0, 255>

Format: String with a ma ximum of 255 characters.

Example:

Phonebook Server 1 URL: "http://tms.company.com/tms/public/external/

phonebook/phonebookservice.asmx"

Page 86

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Provisioning settings

Provisioning Connectivity

This setting controls how the device discovers whether it should request an internal or external configuration from the provisioning server.

Requires user role: ADMIN

Value space: <Internal/External/Auto>

Internal: Request internal configuration. External: Request external configuration. Auto: Automatically discover using NAPTR queries whether internal or external configurations

should be requested. If the NAPTR responses have the "e" flag, external conf igurations will be requested. Otherwise internal configurations will be requested.

Example:

Provisioning Connectivity: Auto

Provisioning Mode

It is possible to configure a video system using a provisioning system (external manager). This allows video conferencing network administrators to manage many video systems simultaneously. With this setting you choose which t ype of provisioning system to use. Provisioning can also be switched off. Contact your provisioning system provider/representative for more information.

Requires user role: ADMIN

Value space: <Off/TMS/VCS/CallWay/CUCM/Auto/Edge>

Off: The video system will not be configured by a provisioning system. Auto: The provisioning server will automatically be selected by the video system. TMS: The video system will be configured using TMS (Cisco TelePresence Management

System). VCS: The video system will be configured using VCS (Cisco TelePresence Video

Communication Server). Callway: The video system will be conf igured using the WebEx TelePresence subscription

service (formerly named Callway). CUCM: The video system will be configured using CUCM (Cisco Unified Communications

Manager). Edge: The system will connect to CUCM via the Collaboration Edge infrastructure.

Example:

Provisioning Mode: Auto

Provisioning LoginName

This is the user name part of the credentials used to authenticate the video system with the provisioning server. This setting must be used when required by the provisioning server. If Provisioning Mode is Callway (WebEx TelePresence), enter the video number.

Requires user role: ADMIN

Value space: <S: 0, 80>

Format: String with a ma ximum of 80 characters.

Example:

Provisioning LoginName: ""

Provisioning Password

This is the password par t of the credentials used to authenticate the video system with the provisioning server. This setting must be used when required by the provisioning server. If Provisioning Mode is Callway (WebEx TelePresence), enter the activation code.

Requires user role: ADMIN

Value space: <S: 0, 64>

Format: String with a ma ximum of 64 characters.

Example:

Provisioning Password: ""

Provisioning HttpMethod

Select the HTTP method to be used for the provisioning.

Requires user role: ADMIN

Value space: <GET/ P O S T>

GE T: Select GET when the provisioning ser ver supports GET. POS T: Select POST when the provisioning ser ver suppor ts POST.

Example:

Provisioning HttpMethod: POST

Page 87

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Provisioning ExternalManager Address

Enter the IP Address or DNS name of the external manager / provisioning system. If an External Manager Address (and Path) is configured, the system will send a mes sage to this

address when starting up. When receiving this message the external manager / provisioning system can retur n configurations/commands to the unit as a result.

When using CUCM or TMS provisioning, the DHCP server can be set up to provide the external manager address automatically (DHCP Option 242 for TMS, and DHCP Option 150 for CUCM). An address set in the Provisioning Exter nalManager Address set ting will override the address provided by DHCP.

Requires user role: ADMIN

Value space: <S: 0, 64>

Format: A valid IPv4 address, IPv6 address or DNS name.

Example:

Provisioning ExternalManager Address: ""

Provisioning ExternalManager AlternateAddress

Only applicable when the endpoint is provisioned by Cisco Unified Communication Manager (CUCM) and an alternate CUCM is available for redundancy. Enter the address of the alternate CUCM. If the main CUCM is not available, the endpoint will be provisioned by the alternate CUCM. When the main CUCM is available again, the endpoint will be provisioned by this CUCM.

Requires user role: ADMIN

Value space: <S: 0, 64>

Format: A valid IPv4 address, IPv6 address or DNS name.

Example:

Provisioning ExternalManager AlternateAdd ress: ""

Provisioning ExternalManager Protocol

Determine whether to use secure management or not.

Requires user role: ADMIN

Value space: <HTTP/HTTPS>

HTTP: Set to HTTP to disable secure management. Requires HT TP to be enabled in the NetworkServices HTTP Mode setting.

HTTPS: Set to HTTPS to enable secure management. Requires HTTPS to be enabled in the NetworkServices HTTPS Mode setting.

Example:

Provisioning ExternalManager Protocol: HTTP

Provisioning ExternalManager Path

Set the Path to the external manager / provisioning system. This setting is required when several management services reside on the same server, i.e. share the same External Manager address.

Requires user role: ADMIN

Value space: <S: 0, 255>

Format: String with a ma ximum of 255 characters.

Example:

Provisioning ExternalManager Path: "tms/public/external/management/

SystemManagementService.asmx"

Provisioning ExternalManager Domain

Enter the SIP domain for the VCS provisioning server.

Requires user role: ADMIN

Value space: <S: 0, 64>

Format: String with a ma ximum of 64 characters.

Example:

Provisioning ExternalManager Domain: "any.domain.com"

Page 88

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

RTP settings

RTP Ports Range Start

Specify the first port in the range of RTP por ts. As default, the system is using the UDP por ts in the range 2326 to 2487 for RTP and RTCP

media data. Each media channel is using two adjacent por ts for RTP and RTCP. The default number of por ts required in the UDP por t range is based on the number of simultaneous calls that the endpoint is capable of.

NOTE: Restar t the system for any change to this set ting to take effect.

Requires user role: ADMIN

Value space: <1024..65438>

Range: Select a value from 1024 to 65438.

Example:

RTP Ports Range Start: 2326

RTP Ports Range Stop

Specify the last RTP port in the range. As default, the system is using the UDP por ts in the range 2326 to 2487 for RTP and RTCP

NOTE: Restar t the system for any change to this set ting to take effect.

Requires user role: ADMIN

Value space: <1120..65535>

Range: Select a value from 1120 to 65535.

Example:

RTP Ports Range Stop: 2486

Page 89

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Security settings

Security Audit Logging Mode

Determine where to record or transmit the audit logs. The audit logs are sent to a syslog ser ver. When using the External/ExternalSecure modes and setting the port assignment to manual in

the Security Audit Server PortAssignment setting, you must also enter the address and port number for the audit server in the Security Audit Server Address and Security Audit Server Por t settings.

Requires user role: AUDIT

Value space: <Off/Internal/External/ExternalSecure>

Off: No audit logging is performed. Internal: The system records the audit logs to internal logs, and rotates logs when they are

full. External: The system sends the audit logs to an external syslog server. The syslog server

must support UDP. ExternalSecure: The system sends encrypted audit logs to an external syslog server that is

verified by a certificate in the Audit CA list. The Audit CA list file must be uploaded to the codec using the web interface. The common_name parameter of a certificate in the CA list must match the IP address of the syslog ser ver, and the secure TCP ser ver must be set up to listen for secure (TLS) TCP Syslog messages.

Example:

Security Audit Logging Mode: Off

Security Audit OnError Action

Determine what happens when the connection to the syslog server is lost. This set ting is only relevant when Security Audit Logging Mode is set to Exter nalSecure.

Requires user role: AUDIT

Value space: <Halt/Ignore>

Halt: If a halt condition is detected the system codec is rebooted and only the auditor is allowed to operate the unit until the halt condition has passed. When the halt condition has passed the audit logs are re-spooled to the syslog server. Halt conditions are: A network breach (no physical link), no syslog ser ver running (or incorrect address or por t to the syslog server), TLS authentication failed (if in use), local backup (re-spooling) log full.

Ignore: The system will continue its normal operation, and rotate internal logs when full. When the connection is restored it will again send its audit logs to the syslog server.

Example:

Security Audit OnError Action: Ignore

Security Audit Server Address

The audit logs are sent to a syslog server. Enter the IP address of the syslog server. Only valid IPv4 or IPv6 address formats are accepted. Host names are not suppor ted. This setting is only relevant when Security Audit Logging Mode is set to Exter nal or ExternalSecure.

Requires user role: AUDIT

Value space: <S: 0, 64>

Format: A valid IPv4 address or IPv6 address

Example:

Security Audit Server Address: ""

Security Audit Server Port

The audit logs are sent to a syslog server. Enter the por t of the syslog server that the system shall send its audit logs to. This setting is only relevant when Security Audit PortAssignment is set to Manual.

Requires user role: AUDIT

Value space: <0..65535>

Range: Select a value from 0 to 65535.

Example:

Security Audit Server Port: 514

Security Audit Server PortAssignment

The audit logs are sent to a syslog server. You can define how the port number of the external syslog ser ver will be assigned. This setting is only relevant when Security Audit Logging Mode is set to Ex ternal or Ex ternalSecure. To see which port number is used you can check the Security Audit Server Port status. Navigate to Configuration > System status on the web interface or; if on a command line interface, run the command xStatus Security Audit Server Port.

Requires user role: AUDIT

Value space: <Auto/Manual>

Auto: Will use UDP port number 514 when the Security Audit Logging M ode is set to External. Will use TCP por t number 6514 when the Securit y Audit Logging Mode is set to ExternalSecure.

Manual: Will use the por t value defined in the Secur ity Audit Server Por t setting.

Example:

Security Audit Server PortAssignment: Auto

Page 90

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Security Session ShowLastLogon

When logging in to the system using SSH or Telnet you will see the UserId, time and date of the last session that did a successful login.

Requires user role: ADMIN

Value space: <Off/On>

On: Show information about the last session. Off: Do not show information about the last session.

Example:

Security Session ShowLastLogon: Off

Security Session InactivityTimeout

Determine how long the system will accept inactivity from the user before he is automatically logged out.

Requires user role: ADMIN

Value space: <0..10000>

Range: Select a value between 1 and 10000 seconds; or select 0 when inactivity should not enforce automatic logout.

Example:

Security Session InactivityTimeout: 0

Page 91

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

SerialPort settings

SerialPort Mode

Enable/disable the serial por t (connection via Micro USB to USB cable). The serial port uses 115200 bps, 8 data bits, no parity and 1 stop bit.

Requires user role: ADMIN

Value space: <Off/On>

Off: Disable the serial port. On: Enable the serial port.

Example:

SerialPort Mode: On

SerialPort LoginRequired

Determine if login shall be required when connecting to the serial por t.

Requires user role: ADMIN

Value space: <Off/On>

Off: The user can access the codec via the serial port without any login. On: Login is required when connecting to the codec via the serial port.

Example:

SerialPort LoginRequired: On

Page 92

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

SIP settings

SIP ANAT

ANAT (Alternative Network Address Types) enables media negotiation for multiple addresses and address types, as specified in RFC 4091.

Requires user role: ADMIN

Value space: <Off/On>

Off: Disable ANAT. On: Enable ANAT.

Example:

SIP ANAT: Off

SIP AuthenticateTransferror

Not applicable in this version.

SIP ListenPort

Turn on or off the listening for incoming connections on the SIP TCP/UDP ports. If turned off, the endpoint will only be reachable through the SIP registrar (CUCM or VCS). It is recommended to leave this setting at its default value.

Requires user role: ADMIN

Value space: <Off/On>

Off: Listening for incoming connections on the SIP TCP/UDP ports is turned off. On: Listening for incoming connections on the SIP TCP/UDP ports is turned on.

Example:

SIP ListenPort: On

SIP PreferredIPMedia

Define the preferred IP version for sending and receiving media (audio, video, data). Only applicable when both Net work IPSt ack and Conference CallProtocolIPStack are set to Dual, and the network does not have a mechanism for cho osing the preferred IP version.

Requires user role: ADMIN

Value space: <IPv4/IPv6>

IPv4: The preferred IP version for media is IPv4. IPv6: The preferred IP version for media is IPv6.

Example:

SIP PreferredIPM ed ia: IP v4

SIP PreferredIPSignaling

Define the preferred IP version for signaling (audio, video, data). Only applicable when both Network IPStack and Conference CallProtocolIPStack are set to Dual, and the network does not have a mechanism for choosing the preferred IP version. It also determines the priority of the A/AA AA lookups in DNS, so that the preferred IP version is used for registration.

Requires user role: ADMIN

Value space: <IPv4/IPv6>

IPv4: The preferred IP version for signaling is IPv4. IPv6: The preferred IP version for signaling is IPv6.

Example:

SIP PreferredIPSig naling: IPv4

SIP OCSP Mode

Not applicable in this version.

SIP OCSP DefaultResponder

Not applicable in this version.

Page 93

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

SIP Profile [1..1] Ice Mode

ICE (Interactive Connectivity Establishment, RFC 5245) is a NAT traversal solution that the endpoints can use to discover the optimized media path. Thus the shortest route for audio and video is always secured between the endpoints. NOTE: ICE is not supported when registered to CUCM (Cisco Unified Communication Manager).

Requires user role: ADMIN

Value space: <Auto/Off/On>

Auto: When set to Auto, ICE will be enabled if a turn server is prov ided, other wise ICE will be disabled.

Off: Set to Of f to disable ICE. On: Set to On to enable ICE.

Example:

SIP Profile 1 Ice Mode: Auto

SIP Profile [1..1] Ice DefaultCandidate

This is the default IP addres s that the endp oint will receive media on until ICE has reached a conclusion about which media route to use (up to the first 5 seconds of a call.

Requires user role: ADMIN

Value space: <Host/Rflx /Relay>

Host: The endpoint will receive media on its own IP address. Rflx: The endpoint will receive media on its public IP address as seen by the TURN server. Relay: The endpoint will receive media on the IP address and port allocated on the TURN

server, and is used as a fallback until ICE has concluded.

Example:

SIP Profile 1 Ice DefaultCandidate: Host

SIP Profile [1..1] Turn DiscoverMode

Set the discover mode to enable/disable the application to search for available Turn servers in DNS. Before making calls, the system will test if port allocation is possible.

Requires user role: ADMIN

Value space: <Off/On>

Off: Set to Of f to disable discovery mode. On: When set to On, the system will search for available Turn server s in DNS, and before

making calls the system will test if port allocation is possible.

Example:

SIP Profile Turn DiscoverMode: On

SIP Profile [1..1] Turn BandwidthProbe

Not applicable in this version.

SIP Profile [1..1] Turn DropRflx

DropRflx will make the endpoint force media through the Turn relay, unless the remote endpoint is on the same network.

Requires user role: ADMIN

Value space: <Off/On>

Off: Disable DropRflx. On: The system will force media through the Turn relay when the remote endpoint is on

another network.

Example:

SIP Profile Turn DropRflx: Off

SIP Profile [1..1] Turn Server

This is the address of the TU RN (Traversal Using Relay NAT) server that the endpoints will use. It is used as a media relay fallback and it is also used to discover the endpoint’s own public IP address.

Requires user role: ADMIN

Value space: <S: 0, 255>

Format: The preferred format is DNS SRV record (e.g. _turn._udp.<domain>), or it can be a valid IPv4 or IP v6 address.

Example:

SIP Profile 1 Turn Server: " _ turn. _ udp.example.com"

SIP Profile [1..1] Turn UserName

The user name needed for accessing the TURN ser ver.

Requires user role: ADMIN

Value space: <S: 0, 128>

Format: String with a ma ximum of 128 characters.

Example:

SIP Profile 1 Turn UserName: ""

Page 94

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

SIP Profile [1..1] Turn Password

The password needed for accessing the TURN ser ver.

Requires user role: ADMIN

Value space: <S: 0, 128>

Format: String with a ma ximum of 128 characters.

Example:

SIP Profile 1 Turn Password: ""

SIP Profile [1..1] URI

The SIP URI (Uniform Resource Identifier) is the address that is used to identify the video system. The UR I is registered and used by the SIP services to route inbound calls to the system. The SIP URI syntax is defined in R FC 3261.

Requires user role: ADMIN

Value space: <S: 0, 255>

Format: String with ma ximum 255 characters and compliant with the SIP URI syntax.

Example:

SIP Profile 1 URI: "sip:firstname.lastname@company.com"

SIP Profile [1..1] DisplayName

When configured the incoming call will report the DisplayName instead of the SIP URI.

Requires user role: ADMIN

Value space: <S: 0, 255>

Format: String with a ma ximum of 255 characters.

Example:

SIP Profile 1 DisplayName: ""

SIP Profile [1..1] Authentication [1..1] LoginName

This is the user name part of the credentials used to authenticate towards the SIP proxy.

Requires user role: ADMIN

Value space: <S: 0, 128>

Format: String with a ma ximum of 128 characters.

Example:

SIP Profile 1 Authentication 1 LoginName: ""

SIP Profile [1..1] Authentication [1..1] Password

This is the password par t of the credentials used to authenticate towards the SIP proxy.

Requires user role: ADMIN

Value space: <S: 0, 128>

Format: String with a maximum of 128 characters.

Example:

SIP Profile 1 Authentication 1 Password: ""

SIP Profile [1..1] DefaultTransport

Select the transport protocol to be used over the LAN.

Requires user role: ADMIN

Value space: <TCP/UDP/T ls/Aut o>

TCP: The system will always use TCP as the default transport method. UDP: The system will always use UDP as the default transport method. Tls: The system will always use TLS as the default transport method. For TLS connections

a SIP CA-list can be uploaded to the video system. If no such CA-list is available on the system then anonymous Dif fie Hellman will be used.

Auto: The system will try to connect using transpor t protocols in the following order: TLS, TC P, U D P.

Example:

SIP Profile 1 DefaultTransport: Auto

SIP Profile [1..1] TlsVerify

For TLS connections a SIP CA-list can be uploaded to the video system. This can be done from the web interface.

Requires user role: ADMIN

Value space: <Off/On>

Off: Set to Of f to allow TLS connections without verif ying them. The TLS connections are allowed to be set up without verifying the x.509 certif icate received from the ser ver against the local CA-list. This should typically be selected if no SIP CA-list has been uploaded.

On: Set to On to verify TLS connections. Only TLS connections to ser vers, whose x.509 certif icate is validated against the CA-list, will be allowed.

Example:

SIP Profile 1 TlsVerify: Off

Page 95

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

SIP Profile [1..1] Outbound

Turn on or off the client initiated connections mechanism for firewall traversal, connection reuse and redundancy. The current version suppor ts RFC 5626.

Requires user role: ADMIN

Value space: <Off/On>

Off: Connect to the single proxy configured first in Proxy Address list. On: Set up multiple outbound connections to ser vers in the Proxy Address list.

Example:

SIP Profile 1 Outbound: Off

SIP Profile [1..1] Proxy [1..4] Address

The Proxy Address is the manually configured address for the outbound proxy. It is possible to use a fully qualified domain name, or an IP address. The default port is 5060 for TCP and UDP but another one can be provided. If SIP Profile Outbound is enabled, multiple proxies can be addressed.

Requires user role: ADMIN

Value space: <S: 0, 255>

Format: A valid IPv4 address, IPv6 address or DNS name.

Example:

SIP Profile 1 Proxy 1 Address: ""

SIP Profile [1..1] Proxy [1..4] Discovery

Select if the SIP Proxy address is to be obtained manually or by using Dynamic Host Configuration Protocol (DHCP).

Requires user role: ADMIN

Value space: <Auto/Manual>

Auto: When Auto is selected, the SIP Proxy address is obtained using Dynamic Host Configuration Protocol (DHCP).

Manual: When Manual is selected, the manually configured SIP Proxy address will be used.

Example:

SIP Profile 1 Proxy 1 Discovery: Manual

SIP Profile [1..1] Type

Enables SIP extensions and special behavior for a vendor or provider.

Requires user role: ADMIN

Value space: <Standard/Cisco>

Standard: Use this when register ing to standard SIP Proxy (tested with Cisco TelePresence VCS and Broadsoft)

Cisco: Use this when registering to Cisco Unified Communication Manager.

Example:

SIP Profile 1 Type: Standard

SIP Profile [1..1] Mailbox

When registered to a Cisco Unif ied Communications Manager (CUCM) you may be of fered the option of having a private voice mailbox. Enter the number (address) of the mailbox in this setting, or leave the string empty if you do not have a voice mailbox.

Requires user role: ADMIN

Value space: <S: 0, 255>>

Format: String with a ma ximum of 255 characters.

Example:

SIP Profile 1 Mailbox: "12345678"

SIP Profile [1..1] Line

When registered to a Cisco Unif ied Communications Manager (CUCM) the endpoint may be part of a shared line. This means that several devices share the same directory number. The different devices sharing the same number receive status from the other appearances on the line as defined in RFC 4235.

Note that shared lines are set up by CUCM, not by the endpoint. Therefore do not change this setting manually; CUCM pushes this information to the endpoint when required.

Requires user role: ADMIN

Value space: <Private/Shared>

Shared: The system is part of a shared line and is therefore sharing its director y number with other devices.

Priv ate: This system is not part of a shared line (default).

Example:

SIP Profile 1 Line: Private

Page 96

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Standby settings

Standby Control

Determine whether the system should go into standby mode or not.

Requires user role: ADMIN

Value space: <Off/On>

Off: The system will not enter standby mode. On: Enter standby mode when the Standby Delay has timed out. Requires the Standby Delay

to be set to an appropriate value.

Example:

Standby Control: On

Standby Delay

Define how long (in minutes) the system shall be in idle mode before it goes into standby mode. Requires the Standby Control to be enabled.

Requires user role: ADMIN

Value space: <1..48 0>

Range: Select a value from 1 to 480 minutes.

Example:

Standby Delay: 10

Standby BootAction

Define the camera position after a restart of the codec.

Requires user role: ADMIN

Value space: <None/Preset1/Preset2/Preset3/Preset4/Preset5/Preset6/Preset7/Preset8/

Preset9/Preset10/Preset11/Preset12/Preset13/Preset14/Preset15/RestoreCameraPosition/ DefaultCameraPosition>

None: No action. Preset1 to Preset15: After a reboot the camera position will be set to the position defined by

the selected preset. RestoreCameraPosition: After a reboot the camera position will be set to the position it had

before the last boot. DefaultCameraPosition: After a reboot the camera position will be set to the factory default

position.

Example:

Stand by B oot Action: DefaultCam eraPosition

Standby StandbyAction

Define the camera position when going into standby mode.

Requires user role: ADMIN

Value space: <None/PrivacyPosition>

None: No action. PrivacyPosition: Turns the camera to a sideways position for privacy.

Example:

Standby StandbyAction: PrivacyPosition

Standby WakeupAction

Define the camera position when leaving standby mode.

Requires user role: ADMIN

Value space: <None/Preset1/Preset2/Preset3/Preset4/Preset5/Preset6/Preset7/Preset8/

Preset9/Preset10/Preset11/Preset12/Preset13/Preset14/Preset15/RestoreCameraPosition/ DefaultCameraPosition>

None: No action. Preset1 to Preset15: When leaving standby the camera position will be set to the position

defined by the selected preset. RestoreCameraPosition: When leaving standby the camera position will be set to the position

it had before entering standby. DefaultCameraPosition: When leaving standby the camera position will be set to the factory

default position.

Example:

Standby WakeupAction: RestoreCameraPosition

Page 97

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

SystemUnit settings

SystemUnit Name

Enter a System Name to define a name of the system unit. If the H.323 Alias ID is configured on the system then this ID will be used instead of the system name. The system name will be displayed:

1) When the codec is acting as an SNMP Agent.

2) Towards a DHCP server.

Requires user role: ADMIN

Value space: <S: 0, 50>

Format: String with a ma ximum of 50 characters.

Example:

SystemUnit Name: "Meeting Room"

SystemUnit MenuLanguage

This has been replaced with the UserInterface Language setting.

SystemUnit CallLogging Mode

Set the call logging mode for calls that are received or placed by the system. The call logs may then be viewed via the web inter face.

Requires user role: ADMIN

Value space: <Off/On>

Off: Disable logging. On: Enable logging.

Example:

SystemUnit CallLogging Mode: On

SystemUnit ContactInfo Type

Choose which type of contact information to show in the status field in the upper lef t corner of the Touch controller.

Requires user role: ADMIN

Value space: <Auto/None/IPv4/IPv6/H323Id/E164Alias/H320Number/SipUri/SystemName/

DisplayName>

Auto: Show the address which another system can dial to reach this system. The address depends on the default call protocol and system registration.

None: Do not show any contact information in the status field. IPv4: Show the IPv4 address as contact information. IPv6: Show the IPv6 address as contact information. H323I d: Show the H.323 ID as contact information (see the H323 Profile [1..1] H323Alias ID

set ti ng). E164 Al ias: Show the H.323 E164 Alias as contact information (see the H323 Profile [1..1]

H323Alias E164 setting). H320Number: Show the H.320 number as contact information (only applicable if connected

to a Cisco TelePresence ISDN Link gateway).

SipUri: Show the SIP URI as contact information (see the SIP Profile [1..1] URI setting). SystemName: Show the system name as contact information (see the SystemUnit Name

set ti ng). DisplayName: Show the display name as contact information (see the SIP Profile [1..1]

DisplayName setting).

Example:

SystemUnit ContactInfo Type: Auto

Page 98

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Time settings

Time TimeFormat

Set the time format.

Requires user role: USER

Value space: <24H/12H>

24H: Set the time format to 24 hours. 12H : Set the time format to 12 hours (AM/PM).

Example:

Time TimeFor m at: 24H

Time DateFormat

Set the date format.

Requires user role: USER

Value space: <DD_MM_YY/MM_DD_YY/YY_MM_DD>

DD _ MM _Y Y: The date January 30th 2010 will be displayed: 30.01.10 MM _ DD_Y Y: The date January 30th 2010 will be displayed: 01.30.10 YY_MM_DD: The date January 30th 2010 will be displayed: 10.01.30

Example:

Tim e DateFor mat: DD _ MM _ YY

Time Zone

This has been replaced with the Time OlsonZone setting as of soft ware version TC7.2.

Page 99

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Time OlsonZone

Set the time zone for the geographical location of the video system. The information in the value space is from the tz database, also called the IANA Time Zone Database.

Requires user role: USER

Value space: <Africa/Abidjan, Africa/Accra, Africa/Addis_Ababa, Africa/Algiers, Africa/Asmara,

Africa/Asmera, Africa/Bamako, Africa/Bangui, Africa/Banjul, Africa/Bissau, Africa/Blantyre, Africa/Brazzaville, Africa/Bujumbura, Africa/Cairo, Africa/Casablanca, Africa/Ceuta, Africa/ Conakry, Africa/Dakar, Africa/Dar_es_Salaam, Africa/Djibouti, Africa/Douala, Africa/El_Aaiun, Africa/Freetown, Africa/Gaborone, Africa/Harare, Africa/Johannesburg, Africa/Juba, Africa/ Kampala, Africa/Khartoum, Africa/Kigali, Africa/Kinshasa, Africa/Lagos, Africa/Libreville, Africa/ Lome, Africa/Luanda, Africa/Lubumbashi, Africa/Lusaka, Africa/Malabo, Africa/Maputo, Africa/ Maseru, Africa/Mbabane, Africa/Mogadishu, Africa/Monrovia, Africa/Nairobi, Africa/Ndjamena, Africa/Niamey, Africa/Nouakchott, Africa/Ouagadougou, Africa/Porto-Novo, Africa/Sao_Tome, Africa/Timbuktu, Africa/Tripoli, Africa/Tunis, Africa/Windhoek, America/Adak, America/ Anchorage, America/Anguilla, America/Antigua, America/Araguaina, America/Argentina/ Buenos_Aires, America/Argentina/Catamarca, America/Argentina/ComodRivadavia, America/ Argentina/Cordoba, America/Argentina/Jujuy, America/Argentina/La_Rioja, America/Argentina/ Mendoza, America/Argentina/Rio_Gallegos, America/Argentina/Salta, America/Argentina/San_ Juan, America/Argentina/San_Luis, America/Argentina/Tucuman, America/Argentina/Ushuaia, America/Aruba, America/Asuncion, America/Atikokan, America/Atka, America/Bahia, America/ Bahia_Banderas, America/Barbados, America/Belem, America/Belize, America/Blanc-Sablon, America/Boa_Vista, America/Bogota, America/Boise, America/Buenos_Aires, America/ Cambridge_Bay, America/Campo_Grande, America/Cancun, America/Caracas, America/ Catamarca, America/Cayenne, America/Cayman, America/Chicago, America/Chihuahua, America/Coral_Harbour, America/Cordoba, America/Costa_Rica, America/Creston, America/ Cuiaba, America/Curacao, America/Danmarkshavn, America/Dawson, America/Dawson_Creek, America/Denver, America/Detroit, America/Dominica, America/Edmonton, America/Eirunepe, America/El_Salvador, America/Ensenada, America/Fort_Wayne, America/For taleza, America/ Glace_Bay, America/Godthab, America/Goose_Bay, America/Grand_Turk, America/Grenada, America/Guadeloupe, America/Guatemala, America/Guayaquil, America/Guyana, America/ Halifax, America/Havana, America/Hermosillo, America/Indiana/Indianapolis, America/Indiana/ Knox, America/Indiana/Marengo, America/Indiana/Petersburg, America/Indiana/Tell_City, America/Indiana/Vevay, America/Indiana/Vincennes, America/Indiana/Winamac, America/ Indianapolis, America/Inuvik, America/Iqaluit, America/Jamaica, America/Jujuy, America/ Juneau, America/Kentucky/Louisville, America/Kentucky/Monticello, America/Knox_IN, America/Kralendijk, America/La_Paz, America/Lima, America/Los_ Angeles, America/Louisville, America/Lower_Princes, America/Maceio, America/Managua, America/Manaus, America/ Marigot, America/Martinique, America/Matamoros, America/Mazatlan, America/Mendoza, America/Menominee, America/Merida, America/Metlakatla, America/Mexico_City, America/ Miquelon, America/Moncton, America/Monterrey, America/Montevideo, America/Montreal, America/Montserrat, America/Nassau, America/New_York, America/Nipigon, America/Nome, America/Noronha, America/North_Dakota/Beulah, America/North_Dakota/Center, America/ North_Dakota/New_Salem, America/Ojinaga, America/Panama, America/Pangnirtung, America/ Paramaribo, America/Phoenix, America/Port-au-Prince, America/Port_of_Spain, America/

Porto_Acre, America/Porto_Velho, America/Puerto_Rico, America/Rainy_River, America/ Rankin_Inlet, America/Recife, America/Regina, America/Resolute, America/Rio_Branco, America/Rosario, America/Santa_Isabel, America/Santarem, America/Santiago, America/ Santo_Domingo, America/Sao_Paulo, America/Scoresbysund, America/Shiprock, America/ Sitka, America/St_Barthelemy, America/St_Johns, America/St_Kitts, America/St_Lucia, America/St_Thomas, America/St_Vincent, America/Swift_Current, America/Tegucigalpa, America/Thule, America/Thunder_Bay, America/Tijuana, America/ Toronto, America/Tortola, America/Vancouver, America/Virgin, America/Whitehorse, America/Winnipeg, America/Yakutat, America/Yellowknife, Antarctica/Casey, Antarctica/Davis, Antarctica/DumontDUrville, Antarctica/ Macquarie, Antarctica/Mawson, Antarctica/McMurdo, Antarctica/Palmer, Antarctica/Rothera, Antarctica/South_Pole, Antarctica/Syowa, Antarctica/Vostok, Arctic/Longyearbyen, Asia/Aden, Asia/Almaty, Asia/Amman, Asia/Anadyr, Asia/Aqtau, Asia/Aqtobe, Asia/Ashgabat, Asia/ Ashkhabad, Asia/Baghdad, Asia/Bahrain, Asia/Baku, Asia/Bangkok, Asia/Beirut, Asia/Bishkek, Asia/Brunei, Asia/Calcutta, Asia/Choibalsan, Asia/Chongqing, Asia/Chungking, Asia/Colombo, Asia/Dacca, Asia/Damascus, Asia/Dhaka, Asia/Dili, Asia/Dubai, Asia/Dushanbe, Asia/Gaza, Asia/ Harbin, Asia/Hebron, Asia/Ho_Chi_Minh, Asia/Hong_Kong, Asia/Hovd, Asia/Irkutsk, Asia/ Istanbul, Asia/Jakarta, Asia/Jayapura, Asia/Jerusalem, Asia/Kabul, Asia/Kamchatka, Asia/ Karachi, Asia/Kashgar, Asia/Kathmandu, Asia/Katmandu, Asia/Khandyga, Asia/Kolkata, Asia/ Krasnoyarsk, Asia/Kuala_Lumpur, Asia/Kuching, Asia/Kuwait, Asia/Macao, Asia/Macau, Asia/ Magadan, Asia/Makassar, Asia/Manila, Asia/Muscat, Asia/Nicosia, Asia/Novokuznetsk, Asia/ Novosibirsk, Asia/Omsk, Asia/Oral, Asia/Phnom_Penh, Asia/Pontianak, Asia/Pyongyang, Asia/ Qatar, Asia/Qyzylorda, Asia/Rangoon, Asia/Riyadh, Asia/Saigon, Asia/Sakhalin, Asia/Samarkand, Asia/Seoul, Asia/Shanghai, Asia/Singapore, Asia/Taipei, Asia/Tashkent, Asia/Tbilisi, Asia/Tehran, Asia/Tel_Aviv, Asia/Thimbu, Asia/Thimphu, Asia/Tokyo, Asia/Ujung_Pandang, Asia/Ulaanbaatar, Asia/Ulan_Bator, Asia/Urumqi, Asia/Ust-Nera, Asia/Vientiane, Asia/Vladivostok, Asia/Yakutsk, Asia/Yekaterinburg, Asia/Yerevan, Atlantic/Azores, Atlantic/Bermuda, Atlantic/Canary, Atlantic/ Cape_Verde, Atlantic/Faeroe, Atlantic/Faroe, Atlantic/Jan_Mayen, Atlantic/Madeira, Atlantic/ Reykjavik, Atlantic/South_Georgia, Atlantic/St_Helena, Atlantic/Stanley, Australia/ACT, Australia/ Adelaide, Australia/Brisbane, Australia/Broken_Hill, Australia/Canberra, Australia/Currie, Australia/Darwin, Australia/Eucla, Australia/Hobart, Australia/LHI, Australia/Lindeman, Australia/ Lord_Howe, Australia/Melbourne, Australia/NSW, Australia/North, Australia/Perth, Australia/ Queensland, Australia/South, Australia/Sydney, Australia/Tasmania, Australia/Victoria, Australia/ West, Australia/Yancowinna, Brazil/Acre, Brazil/DeNoronha, Brazil/East, Brazil/West, CET, CST6CDT, Canada/Atlantic, Canada/Central, Canada/East-Saskatchewan, Canada/Eastern, Canada/Mountain, Canada/Newfoundland, Canada/Pacific, Canada/Saskatchewan, Canada/ Yukon, Chile/Continental, Chile/EasterIsland, Cuba, EE T, EST, EST5EDT, Egypt, Eire, Etc/GMT, Etc/GMT+0, Etc/GMT+1, Etc/GMT+10, Etc/GMT+11, Etc/GMT+12, Etc/GMT+2, Etc/GMT+3, Etc/ GMT+4, Etc/GMT+5, Etc/GMT+6, Etc/GMT+7, Etc/GMT+8, Etc/GMT+9, Etc/GMT-0, Etc/GMT-1, Etc/GMT-10, Etc/GMT-11, Etc/GMT-12, Etc/GMT-13, Etc/GMT-14, Etc/GMT-2, Etc/GMT-3, Etc/ GMT-4, Etc/GMT-5, Etc/GMT-6, Etc/GMT-7, Etc/GMT-8, Etc/GMT-9, Etc/GMT0, Etc/Greenwich, Etc/UCT, Etc/UTC, Etc/Univer sal, Etc/Zulu, Europe/Amsterdam, Europe/Andorra, Euro pe/Athens, Europe/Belfast, Europe/Belgrade, Europe/Berlin, Europe/Bratislava, Europe/Brussels, Europe/ Bucharest, Europe/Budapest, Europe/Busingen, Europe/Chisinau, Europe/Copenhagen, Europe/ Dublin, Europe/Gibraltar, Europe/Guernsey, Europe/Helsinki, Europe/Isle_of_Man, Europe/ Istanbul, Europe/Jersey, Europe/Kaliningrad, Europe/Kiev, Europe/Lisbon, Europe/Ljubljana, Europe/London, Europe/Luxembourg, Europe/Madrid, Europe/Malta, Europe/Mariehamn,

Page 100

100

Cisco TelePresence MX200 G2 and MX300 G2 Administrator Guide

Europe/Minsk, Europe/Monaco, Europe/Moscow, Europe/Nicosia, Europe/Oslo, Europe/Paris, Europe/Podgorica, Europe/Prague, Europe/Riga, Europe/Rome, Europe/Samara, Europe/ San_Marino, Europe/Sarajevo, Europe/Simferopol, Europe/Skopje, Europe/Sofia, Europe/ Stockholm, Europe/Tallinn, Europe/Tirane, Europe/Tiraspol, Europe/Uzhgorod, Europe/Vaduz, Europe/Vatican, Europe/Vienna, Europe/Vilnius, Europe/Volgograd, Europe/Warsaw, Europe/ Zagreb, Europe/Zaporozhye, Europe/Zurich, GB, GB-Eire, GMT, GMT+0, GMT-0, GMT0, Greenwich, HST, Hongkong, Iceland, Indian/Antananarivo, Indian/Chagos, Indian/Christmas, Indian/Cocos, Indian/Comoro, Indian/Kerguelen, Indian/Mahe, Indian/Maldives, Indian/Mauritius, Indian/Mayotte, Indian/Reunion, Iran, Israel, Jamaica, Japan, Kwajalein, Libya, MET, MST, MST7MDT, Mexico/BajaNor te, Mexico/BajaSur, Mexico/General, NZ, NZ-CHAT, Navajo, PRC, PST8PDT, Pacific/Apia, Pacific/Auckland, Pacific/Chatham, Pacific/Chuuk, Pacific/Easter, Pacific/Efate, Pacific/Enderbury, Pacific/Fakaofo, Pacific/Fiji, Pacific/Funafuti, Pacific/Galapagos, Pacific/Gambier, Pacific/Guadalcanal, Pacific/Guam, Pacific/Honolulu, Pacific/Johnston, Pacific/ Kiritimati, Pacific/Kosrae, Pacific/Kwajalein, Pacific/Majuro, Pacific/Marquesas, Pacific/Midway, Pacific/Nauru, Pacific/Niue, Pacific/Norfolk, Pacific/Noumea, Pacific/Pago_Pago, Pacific/Palau, Pacific/Pitcairn, Pacific/Pohnpei, Pacific/Ponape, Pacific/Port_Moresby, Pacific/Rarotonga, Pacific/Saipan, Pacific/Samoa, Pacific/Tahiti, Pacific/Tarawa, Pacific/Tongatapu, Pacific/Truk, Pacific/Wake, Pacific/Wallis, Pacific/Yap, Poland, Portugal, ROC, ROK, Singapore, Turkey, UCT, US/Alaska, US/Aleutian, US/Arizona, US/Central, US/East-Indiana, US/Eastern, US/Hawaii, US/ Indiana-Starke, US/Michigan, US/Mountain, US/Pacific, US/Pacific-New, US/Samoa, UTC, Universal, W-SU, WET, Zulu>

Range: Select a time zone from the list.

Example:

Range: Select a time zone from the list time zones.