Page 1
Installing Cisco TelePresence MX200 G2 - Wall Mount
78-100249-02A0 | JUNE 2016 | © 2016 Cisco Systems, Inc. Al l rights res erved.
1
Manpower
Two people working together are required to mount
the system.
Room setup
Explore the Cisco Project Workplace website to
find inspiration and guidelines when preparing your
office or meeting room for video conferencing,
http://www.cisco.com/go/projectworkplace
Documentation
Cisco Spark: Visit the Cisco Spark help site to find
more information about Spark registered room
systems, http://help.ciscospark.com
Other services: Visit the Cisco web site to find user
guides and compliance and safety information for
the video system, http://www.cisco.com/go/mx-docs
This installation guide covers MX200 G2 with a wall-mount.
Dimensions
Height: 745 mm / 29.3 in.
Width: 995 mm / 39.2 in.
Depth: 150 mm / 5.8 in.
Weight total: 26 kg / 57 lb
Weight monitor: 24 kg / 53 lb
Page 2
Installing Cisco TelePresence MX200 G2 - Wall Mount
78-100249-02A0 | JUNE 2016 | © 2016 Cisco Systems, Inc. Al l rights res erved.
2
• Wall bracket
• Monitor bracket
• Bottom adapter
• Screwdriver
C
D
A
B
Monitor
Accessories:
• Microphone(s)
• Cables
• Screws for mounting
the bottom adapter
• Gloves
Touch controller
Page 3
Installing Cisco TelePresence MX200 G2 - Wall Mount
78-100249-02A0 | JUNE 2016 | © 2016 Cisco Systems, Inc. Al l rights res erved.
3
1
Mount the monitor bracket
Use gloves when
handling the monitor.
A
B
C
Fasten the bracket
with the four screws
that you just removed.
Unscrew these four
screws. You will
re-use them when
fastening the bracket.
Lay the monitor gently face
down on a steady, soft surface.
Take care not to subject the camera
for any stress.
1
2
Page 4
Installing Cisco TelePresence MX200 G2 - Wall Mount
78-100249-02A0 | JUNE 2016 | © 2016 Cisco Systems, Inc. Al l rights res erved.
4
2
Mount the bottom adapter
Remove the cable
channel lid for now.
You need it in step 4.
2 × M6x16
A
C
Page 5
Installing Cisco TelePresence MX200 G2 - Wall Mount
78-100249-02A0 | JUNE 2016 | © 2016 Cisco Systems, Inc. Al l rights res erved.
5
3
Connect the cables
For maintenance only
Reset to factory
settings
Audio line output
Always use the provided
power cable.
The wall socket outlet must
be easily accessible after
installation.
Power switch
Audio line input
LAN
1
Video input2
(e.g. PC)
Video output2
(e.g. 2nd display)
Power
(100-240 VAC,
50/60 Hz)
Touch
controller
1
USB, for future use
HDMI
DVI-I
Microphone
3
2nd microphone
2, 3
C
D
1
Use the cable that is labeled with
for the Touch controller; use the cable
that is labeled with
for the LAN
2
Optional
3
Always use the provided Cisco
TelePresence Table Microphone 20
Page 6
Installing Cisco TelePresence MX200 G2 - Wall Mount
78-100249-02A0 | JUNE 2016 | © 2016 Cisco Systems, Inc. Al l rights res erved.
6
4
Snap on the cable channel lid
Snap on the cable
channel lid for strain relief.
Page 7
Installing Cisco TelePresence MX200 G2 - Wall Mount
78-100249-02A0 | JUNE 2016 | © 2016 Cisco Systems, Inc. Al l rights res erved.
7
5
Mount the monitor to the wall
Due to the size and mass of this product, it is
important that the wall-mounted system is safely
installed according to these installation instructions.
The wall and mounting hardware must be able to
safely support the product.
The wall-mounted system must be installed by
qualified personnel, in accordance with state and
local building regulations.
26 kg / 57 lb
(including brackets)
Use gloves when
handling the monitor.
Fix the bracket to the wall
with four screws. Use screws
and anchors suiting your
type of wall (not provided).
Verify that the bracket is level
before securing it to the wall.
1.2 m
(47 i n.)
Recommended distance
for regular meeting rooms:
A
Page 8
Installing Cisco TelePresence MX200 G2 - Wall Mount
78-100249-02A0 | JUNE 2016 | © 2016 Cisco Systems, Inc. Al l rights res erved.
8
EMC Class A declaration
WARNING: This is a class A product. In a domestic environment this
product may cause radio interference in which case the user may be
required to take adequate measures.
声 明
A级产品，在生活环境中，该产品可能会造成无线电干扰。在这种
• Connect to power and LAN/Ethernet.
• Switch on the system.
The power switch is placed next to
the power connector at the rear side
of the system.
Wait while the unit starts up. Normally
this takes a few minutes. It may
include automatic software upgrade
and restart of the Touch controller.
• Follow the instructions on the Touch controller.
Cisco Spark: To find more information on how to get started with
Spark registered systems, visit http://help.ciscospark.com and look
for Getting Started articles for room systems.
Other services: For further information on set-up and configuration,
download the Getting Started Guide from the Cisco web site,
http://www.cisco.com/go/mx-docs
Never move the camera manually when power is switched on;
always use the camera control function on the Touch controller to
change the camera position.
6
Start up the system
Power
switch
Cisco and th e Cisco log o are tradem arks or regi stered trad emarks of Ci sco and/or
its affi liates in the U.S. a nd other cou ntries. To view a lis t of Cisco tra demarks, go to
this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the
proper ty of their re spectiv e owners. Th e use of the word p artner d oes not impl y a
partne rship relat ionship b etween Cis co and any othe r company. (1110R)
Cisco has more than 200 offices worldwide.
Find an overview of the offices on the Cisco web site at
http://ww w.cisco.com/go/off ices
Loading...