Cisco Linksys WAG310G User Manual

Download

Page 1

USER GUIDE

Wireless-G

ADSL2+ Gateway with VoIP

Model: WAG310G

Page 2

About This Guide

Icon Descriptions

While reading through the User Guide you may see various icons that call attention to specific items. Below is a description of these icons:

NOTE: This check mark indicates that there is

a note of interest and is something that you should pay special attention to while using the product.

WARNING: This exclamation point indicates

that there is a caution or warning and it is something that could damage your property or product.

About This Guide

WEB: This globe icon indicates a noteworthy

website address or e-mail address.

Linksys, Cisco and the Cisco Logo are registered trademarks or trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2008 Cisco Systems, Inc. All rights reserved. Other brands and product names are trademarks or registered trademarks of their respective holders.

Wireless-G ADSL2+ Gateway with VoIP

Page 3

Table of Contents

Chapter 1: Product Overview 4

Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Top Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Placement Positions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Chapter 2: Wireless Security Checklist 7

General Network Security Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Additional Security Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Chapter 3: Advanced Conguration 8

Setup > ADSL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Setup > ADSL (WAN Connection for PVC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Setup > Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Setup > Local Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Setup > DDNS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Setup > Advanced Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Setup > PVC/VLAN Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Wireless > Basic Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Wireless > Security. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Wireless > MAC Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Wireless > Wi-Fi Protected Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Wireless > Advanced Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Voice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Voice > Info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Voice > System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Voice > User1/2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Storage > Disk Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Storage > Disk Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Security > Firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Access Restrictions > Internet Access Policy. . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Applications and Gaming > Single Port Forwarding. . . . . . . . . . . . . . . . . . . . . . . .31

Applications and Gaming > DMZ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Applications and Gaming > QoS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Applications and Gaming > Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Administration > Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Administration > Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Administration > Backup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Administration > Upgrade. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Administration > Reboot. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Administration > Logout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Status > Internet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Status > Local Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Status > Wireless . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Wireless-G ADSL2+ Gateway with VoIP

Page 4

Status > DSL Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Status > Bridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Table of Contents

Appendix A: Troubleshooting 42

Appendix B: Specications 43

Appendix C: Regulatory Information 44

United States of America. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Wireless Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Avis de non-responsabilité concernant les appareils sans l . . . . . . . . . . . . . . . . . .46

New Zealand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

European Union . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Appendix D: Software License Agreement 54

Software in Linksys Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54

Software Licenses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54

Wireless-G ADSL2+ Gateway with VoIP

iii

Page 5

Chapter 1

Product Overview

Chapter 1: Product Overview

Thank you for choosing the Linksys Wireless-G ADSL2+ Gateway with VoIP. The Gateway lets you access the Internet via a wireless connection or through one of its four (or five) switched ports. It also connects to the Public Switched Telephone Network (PSTN), which is the network that traditional phone service uses, so you can make calls using the traditional service or Voice over IP (VoIP).

You can also use the Gateway to share resources such as computers and storage. Various security features help to protect your data and your privacy while you are online. Security features include WPA2 security, a Stateful Packet Inspection (SPI) firewall and NAT technology. Configuring the Gateway is easy using the provided browser-based utility.

Front Panel

Wireless Security (Green/Red) The Security

LED lights up when wireless security is enabled. It flashes during the Wi-Fi Protected Setup process. The LED becomes red when wireless security is disabled.

USB Green. The USB LED lights up when the

Gateway is connected to a device through the USB port. It flashes to indicate USB activity.

Phone 1-2 (Green) The Phone 1 or 2 LED

lights up when a phone is connected to the corresponding port on the Gateway’s back panel. It flashes when the phone is being used.

Line (Green) The Line LED lights up when the

Gateway is connected to the Public Switched Telephone Network (PSTN) through the Line port. It flashes when the phone line is in use.

DSL (Green) The DSL LED lights up when there

is a DSL connection. It flashes when the Gateway is establishing the ADSL connection.

Internet (Green/Red) The Internet LED lights

up when the Gateway is connected to the Internet. It flashes to indicate network activity over the Internet port. The LED becomes red when the Internet connection fails.

Power (Green/Red) The Power LED lights up

when the Gateway is powered on. It flashes during the self-test. The LED becomes red during a malfunction.

Ethernet LAN 1-4 (Green) These numbered

LEDs, corresponding with the numbered Ethernet ports on the Gateway’s back panel, serve two purposes. If the LED is continuously lit, the Gateway is connected to a device through that port. It flashes to indicate network activity over that port.

Ethernet WAN/LAN 5 (Green) The WAN/LAN 5

LED corresponds with the WAN/LAN5 port and serves two purposes. If the LED is continuously lit, the Gateway is successfully connected to a device through that port. It flashes to indicate network activity over that port.

Wireless Activity (Green) The Activity LED

lights up when the wireless feature is enabled. It flashes when the Gateway is sending or receiving data over the wireless network.

Top Panel

Wireless-G ADSL2+ Gateway with VoIP

Page 6

Chapter 1

Product Overview

Wi-Fi Protected Setup If you have client

devices, such as a wireless adapter, that supports Wi-Fi Protected Setup, then you can use Wi-Fi Protected Setup to automatically configure wireless security for your wireless network(s).

NOTE: Wi-Fi Protected Setup can

only be used for the default wireless network. (The Gateway supports up to four wireless networks. The other three can be configured using the Gateway’s web-based utility.)

Follow the appropriate instructions:

Method #1

Use this method if your client device has a Wi-Fi Protected Setup button.

Click or press the1. Wi-Fi Protected Setup button on the client device. (If Wi-Fi Protected Setup is an on-screen option, then select it.)

Click the 2. Wi-Fi Protected Setup button on the top panel of the Gateway.

After the client device has been configured, 3. refer back to your client device or its documentation for further instructions.

Method #2

Use this method if your client device has a Wi-Fi Protected Setup PIN number.

Access the Gateway’s web-based utility.1. Click the 2. Wireless tab. Click the 3. Wi-Fi Protected Setup tab Enter the client PIN number in the4. PIN field

on this screen (the Gateway’s Wi-Fi Protected Setup screen).

Click 5. Register.

Method #3

Use this method if your client device asks for the Gateway’s PIN number.

Enter the PIN number listed on the label on 1. the bottom of the Gateway.)

After the client device has been configured, 2. refer back to your client device or its documentation for further instructions.

NOTE: Wi-Fi Protected Setup

configures one client device at a time. Repeat the instructions for each client device that supports Wi-Fi Protected Setup.

Back Panel

DSL The DSL port connects to the ADSL line.

Line The Line port connects to either the voice

connection on the DSL microfilter or wall jack.

Phone 1-2 The Phone ports connect standard

analog telephones to the Gateway.

USB The USB port connects to a USB storage

device, such as a USB hard drive or flash disk.

Ethernet WAN/LAN5 The WAN/LAN5 port can

act as a Wide Area Network (WAN) or Local Area Network (LAN) port. As a WAN port, it connects to a broadband modem. As a LAN port, it connects to a wired computer or other Ethernet network device.

Ethernet LAN 1-4 These Ethernet ports (1, 2,

3, 4) connect the Gateway to wired computers and other Ethernet network devices.

Power Switch Use this switch to power on or

off the Gateway.

Wireless-G ADSL2+ Gateway with VoIP

Power The Power port is where you will

connect the power adapter.

Page 7

Chapter 1

54 mm

Product Overview

Reset There are two ways to reset the Gateway’s

settings to factory defaults. Either press and hold the Reset button for approximately ten seconds, or restore the defaults from the Administration > Factory Defaults screen of the Gateway’s web-based utility.

NOTE: The reset does not restore the

voice settings to the factory defaults.

Placement Positions

There are two ways to physically install the Gateway. The first way is to place the Gateway horizontally on a surface. The second way is to mount the Gateway on a wall.

Horizontal Placement

The Gateway has four rubber feet on its bottom panel. Place the Gateway on a level surface near an electrical outlet.

NOTE: Linksys is not responsible for damages

incurred by insecure wall-mounting hardware.

Follow these instructions:

Determine where you want to mount the Gateway. 1. Make sure that the wall you use is smooth, flat, dry, and sturdy. Also make sure the location is within reach of an electrical outlet.

Drill two holes into the wall. Make sure the holes are 2. 54 mm (2.13 inches) apart.

Insert a screw into each hole and leave 2 mm 3. (0.8 inches) below the head exposed.

Maneuver the Gateway so two of the wall-mount slots 4. line up with the two screws.

Place the wall-mount slots over the screws and slide 5. the Gateway down until the screws fit snugly into the wall-mount slots.

NOTE: To safely wall-mount the Gateway, the

side panel with the antenna must face upward.

Wall-Mounting Placement

The Gateway has four wall-mount slots on its bottom panel. The distance between two adjacent slots is 54 mm (2.13 inches).

Two screws are needed to mount the Gateway.

Suggested Mounting Hardware

4-5 mm 1-1.5 mm

Note: Mounting hardware illustrations are not † true to scale.

Wireless-G ADSL2+ Gateway with VoIP

2.5-3.0 mm

Print this page at 100% size. Cut along the dotted line, and place on the wall to drill precise spacing.

Wall Mounting Template

Page 8

Chapter 2

Wireless Security Checklist

Chapter 2: Wireless Security Checklist

Wireless networks are convenient and easy to install, so homes with high-speed Internet access are adopting them at a rapid pace. Because wireless networking operates by sending information over radio waves, it can be more vulnerable to intruders than a traditional wired network. Like signals from your cellular or cordless phones, signals from your wireless network can also be intercepted. Since you cannot physically prevent someone from connecting to your wireless network, you need to take some additional steps to keep your network secure.

1. Change the default wireless network name or SSID

Wireless devices have a default wireless network name or Service Set Identifier (SSID) set by the factory. This is the name of your wireless network, and can be up to 32 characters in length. Linksys wireless products use linksys as the default wireless network name. You should change the wireless network name to something unique to distinguish your wireless network from other wireless networks that may exist around you, but do not use personal information (such as your Social Security number) because this information may be available for anyone to see when browsing for wireless networks.

2. Change the default password

For wireless products such as access points, routers, and gateways, you will be asked for a password when you want to change their settings. These devices have a default password set by the factory. The Linksys default password is admin. Hackers know these defaults and may try to use them to access your wireless device and change your network settings. To thwart any unauthorized changes, customize the device’s password so it will be hard to guess.

4. Enable encryption

Encryption protects data transmitted over a wireless network. Wi-Fi Protected Access (WPA/WPA2) and Wired Equivalency Privacy (WEP) offer different levels of security for wireless communication.

A network encrypted with WPA/WPA2 is more secure than a network encrypted with WEP, because WPA/WPA2 uses dynamic key encryption. To protect the information as it passes over the airwaves, you should enable the highest level of encryption supported by your network equipment.

WEP is an older encryption standard and may be the only option available on some older devices that do not support WPA.

General Network Security Guidelines

Wireless network security is useless if the underlying network is not secure.

Password protect all computers on the network and • individually password protect sensitive files.

Change passwords on a regular basis. •

Install anti-virus software and personal firewall • software.

Disable file sharing (peer-to-peer). Some applications • may open file sharing without your consent and/or knowledge.

Additional Security Tips

Keep wireless routers, access points, or gateways away • from exterior walls and windows.

Turn wireless routers, access points, or gateways • off when they are not being used (at night, during vacations).

Use strong passphrases that are at least eight characters • in length. Combine letters and numbers to avoid using standard words that can be found in the dictionary.

3. Enable MAC address filtering

Linksys routers and gateways give you the ability to enable Media Access Control (MAC) address filtering. The MAC address is a unique series of numbers and letters assigned to every networking device. With MAC address filtering enabled, wireless network access is provided solely for wireless devices with specific MAC addresses. For example, you can specify the MAC address of each computer in your home so that only those computers can access your wireless network.

Wireless-G ADSL2+ Gateway with VoIP

WEB: For more information on wireless

security, visit www.linksys.com/security

Page 9

Chapter 3

Advanced Configuration

Chapter 3: Advanced Configuration

To configure the Gateway, use its web-based utility. This chapter describes each web page of the utility and each page’s key functions. You can access the utility via a web browser on a computer connected to the Gateway.

NOTE: If your service provider supplied you with

the Gateway, then it may be pre-configured for you, and you will not need to make any changes. Contact your service provider for more information.

The web-based utility has these main tabs: Setup, Wireless, Voice, Storage, Security, Access Restrictions, Applications & Gaming, Administration, and Status. Additional tabs will be available after you click one of the main tabs.

NOTE: For New Zealand residents, refer to the

note under RFC 2364 PPPoA.

Setup > ADSL

The first screen that appears is the Basic Setup screen. Configure the Gateway’s ADSL settings on this screen.

There are two views available, Basic and Advanced. The default view is Basic. To display the Advanced View, click

Advanced View. To return to the Basic View, click Basic View.

How to Access the Web-Based Utility

To access the web-based utility, launch the web browser on your computer, and enter the Gateway’s default IP address, 192.168.1.1, in the Address field. Then, press Enter.

A login screen appears. The first time you open the webbased utility, use the default user name and password, admin. (You can set a new user name and password from the Administration tab’s Management screen.) Click OK to continue.

NOTE: If the Gateway was supplied by your

service provider, then it may restrict access to the web-based utility. Contact your service provider for the login information.

Setup > ADSL (Advanced View)

Internet Setup

PVC Connection

The Gateway supports up to eight Private Virtual Circuit (PVC) connections. The default PVC addresses are 0/35,

8/35, 0/43, 0/51, 0/59, 8/43, 8/51, and 8/59.

Select PVC Connection Select the connection you want

to configure.

Enable Now Select this option to enable the selected

connection. By default, only PVC 1 is enabled. The other seven PVCs are disabled. You must enable them before configuring layer 3 connections on top of them.

To configure the PVC settings separately from the Wide Area Network (WAN) connections, you can save the PVC settings separately. Click Save PVC.

Wireless-G ADSL2+ Gateway with VoIP

Page 10

Chapter 3

Advanced Configuration

NOTE: PVCs are layer 2 (physical and link), while

WAN connections are layer 3, meaning IP and Point-to-Point (PPP) connections. Each PVC supports multiple connections. For each PVC, you can configure one IP connection and up to four PPP over Ethernet (PPPoE) connections.

VC Settings (Advanced View)

Configure your Virtual Circuit (VC) settings in this section.

Multiplexing Select LLC or VCMUX, depending on your

service provider. The default is LLC.

QoS Type Select from the drop-down menu: CBR

(Constant Bit Rate) to specify fixed bandwidth for voice or data traffic; UBR (Unspecified Bit Rate) for application that are not time-sensitive, such as e-mail; VBR_rt; or VBR_ nrt. VBR (Variable Bit Rate) is used for bursty traffic and bandwidth-sharing with other applications. VBR_rt (real time) is more time-sensitive than VBR_nrt (non-real time), and VBR_rt is typically used for voice and video traffic.

NOTE: If the QoS Type setting is CBR, then the SCR

Rate is not configurable. If the QoS Type setting is UBR, then the PCR and SCR Rate settings are not configurable.

IPoE (RFC2684 Bridged) •

IPoA (RFC2684 Routed) •

PPPoE (RFC 2516) •

PPPoA (RFC 2364) •

Connection Select the appropriate encapsulation

method from the drop-down menu.

Follow the instructions for your connection type.

IPoE (RFC2684 Bridged)

If you are required to use IPoE (RFC2684 Bridged), then select IPoE (RFC2684 Bridged).

Connection Type > IPoE (RFC2684 Bridged)

IP Settings

Select Obtain an IP Address Automatically if your service provider says you are connecting through a dynamic IP address. Then configure the following settings:

PCR Rate The Peak Cell Rate (PCR) is the maximum

allowable rate at which cells can be transported. Enter the rate in the field (if required by your service provider).

SCR Rate The Sustainable Cell Rate (SCR) sets the average

cell rate that can be transmitted. The SCR value is normally less than the PCR value. Enter the rate in the field (if required by your service provider).

Max Burst Size Enter the maximum burst size of cells.

Autodetect Select Enable to have the settings

automatically entered, or select Disable to enter the values manually.

Virtual Circuit These fields consist of two items: VPI

(Virtual Path Identifier) and VCI (Virtual Channel Identifier). Enter the settings provided by your service provider.

DSL Modulation Select the appropriate mode:

MultiMode, T1.413, G.dmt, G.lite, ADSL2, ADSL2 (Annex L), ADSL2 (Annex M), ADSL2+, or ADSL2+ (Annex M).

Contact your service provider if you are not sure which mode to use.

To save the modulation setting, click Save Modulation.

Connection Type

Primary (Required) and Secondary (Optional) DNS Enter the DNS (Domain Name System) server IP

address(es) provided by your service provider. At least one is required.

If you are required to use a permanent (static) IP address to connect to the Internet, then select Use the following IP Address. Your service provider provides the settings needed for the following fields:

Internet IP Address Enter the Gateway’s IP address, as

seen from the Internet.

Subnet Mask Enter the Gateway’s Subnet Mask, as seen

from the Internet (including your service provider).

Default Gateway Enter the IP address of the service

provider’s server.

Primary (Required) and Secondary (Optional) DNS Enter the DNS (Domain Name System) server IP

address(es) provided by your service provider. At least one is required.

IPoA (RFC2684 Routed)

If you are required to use IPoA (IP over ATM), then select IPoA (RFC2684 Routed).

Configure the appropriate encapsulation method of the WAN connection. Each Basic Setup screen and available features will differ depending on which encapsulation method you select. These are the available methods:

Wireless-G ADSL2+ Gateway with VoIP

Page 11

Chapter 3

Connection Type > IPoA (RFC2684 Routed)

IP Settings

Your service provider provides the settings needed for the following fields:

Internet IP Address Enter the Gateway’s IP address, as

seen from the Internet.

Subnet Mask Enter the Gateway’s Subnet Mask, as seen

from the Internet (including your service provider).

Default Gateway Enter the IP address of the service

provider’s server.

Advanced Configuration

select Connect on Demand. In the Max Idle Time field, enter the number of minutes you want to have elapsed before your Internet connection terminates. The default Max Idle Time is 5 minutes.

Keep Alive If you select this option, the Gateway will

periodically check your Internet connection. If you are disconnected, then the Gateway will automatically reestablish your connection. To use this option, select Keep

Alive.

Service Name (Advanced View) Enter the Service Name

(optional) provided by your service provider.

PPPoA (RFC 2364)

Some DSL-based service providers use PPPoA (Point-toPoint Protocol over ATM) to establish Internet connections. If you are connected to the Internet through a DSL line, check with your service provider to see if they use PPPoA. If they do, you will have to enable PPPoA.

Primary (Required) and Secondary (Optional) DNS Enter the DNS (Domain Name System) server IP

address(es) provided by your service provider. At least one is required.

PPPoE (RFC 2516)

Some DSL-based service providers use PPPoE (Pointto-Point Protocol over Ethernet) to establish Internet connections. If you are connected to the Internet through a DSL line, check with your service provider to see if they use PPPoE. If they do, you will have to enable PPPoE.

Internet Connection Type > PPPoE (RFC 2516)

PPPoE Settings

Primary (Required) and Secondary (Optional) DNS Enter the DNS (Domain Name System) server IP

address(es) provided by your service provider. At least one is required.

Username and Password Enter the Username and

Password provided by your service provider.

Connect on Demand: Max Idle Time You can configure

Internet Connection Type > PPPoA (RFC 2364)

PPPoA Settings

Primary (Required) and Secondary (Optional) DNS Enter the DNS (Domain Name System) server IP

address(es) provided by your service provider. At least one is required.

Username and Password Enter the Username and

Password provided by your service provider.

Connect on Demand: Max Idle Time You can configure

the Gateway to cut the Internet connection after it has been inactive for a specified period of time (Max Idle Time). If your Internet connection has been terminated due to inactivity, Connect on Demand enables the Gateway to automatically re-establish your connection as soon as you attempt to access the Internet again. To use this option, select Connect on Demand. In the Max Idle Time field, enter the number of minutes you want to have elapsed before your Internet connection terminates. The default Max Idle Time is 5 minutes.

Keep Alive If you select this option, the Gateway will

periodically check your Internet connection. If you are disconnected, then the Gateway will automatically reestablish your connection. To use this option, select Keep

Alive.

Wireless-G ADSL2+ Gateway with VoIP

Page 12

Chapter 3

Advanced Configuration

Service Name (Advanced View) Enter the Service Name

(optional) provided by your service provider.

NOTE: For New Zealand, follow these

instructions:

Select 1. PPPoE (RFC 2364) from the Connection drop-down menu.

For the Virtual Circuit ID, enter 2. 0 for the VPI and 100 for the VCI.

Select 3. VCMUX for Multiplexing. Select 4. MultiMode from the DSL Modulation

drop-down menu.

Obtain the User Name and Password details 5. from your service provider.

NAT (Advanced View) To use Network Address

Translation, keep the default Enabled. Otherwise, select Disabled.

IGMP Forwarding (Advanced View) Select Enabled, if

you want to allow multicast traffic through the Router for your multimedia application devices. Otherwise, keep the default, Disabled.

Optional Settings (Advanced View)

MTU Size Keep this value in the 1200 to 1500 range. The

default MTU is configured automatically.

Override MAC Address Select this option to override the

MAC address of this connection.

MAC Address If the Override MAC Address option is

enabled, enter the MAC address you want to use.

To add the connection you have configured, click Add Connection, or click Cancel Changes to cancel your changes.

After the connection has been added, a new screen appears with the PVC connection selected. You can use this screen to change settings. Refer to the following section, “Setup > ADSL (WAN Connection for PVC)”, for details.

Setup > ADSL (WAN Connection for PVC)

Use this screen to change settings for the selected Wide Area Network (WAN) connection. For most WAN connection types, the displayed settings match the settings on the Setup > ADSL screen; however, additional options appear for IPoE.

Dedicate The Connection To Voice (FXS1/FXS2) (Advanced View) Select Enabled, if you want to use this

connection for FXS1/FXS2 outbound phone calls. (You can enable this option for only one Internet connection.) Otherwise, keep the default, Disabled.

VLAN ID Mark (Advanced View) Enter the 802.1Q VLAN

ID Mark to be used on egress to the interface associated with this connection. A value of -1 indicates no VLAN tagging for this connection. The default is -1.

802.1p Mark (Advanced View) Enter the 802.1p

(Ethernet priority) Mark to be used on traffic sent out on this connection. A value of -1 indicates no change from the incoming packet. The default is -1.

Override Ethernet Priority (Advanced View) If this

option is disabled and the 802.1p Mark is specified, then the 802.1p Mark is applied only to packets of priority 0. If this option is enabled and the 802.1p Mark is specified, then the 802.1p Mark is applied to all packets on this connection. To enable this option, select the check box. Otherwise, leave the check box blank.

RIP Recv Packet Version (Advanced View) Select the

Routing Information Protocol (RIP) version you want to use: RIP off, RIPv1, or RIPv2.

NOTE: PVCs are layer 2 (physical and link), while

Domain Name (Advanced View) Enter the Domain

Name for this connection. The DNS proxy will compare Domain Names to choose the connection that will send out DNS queries.

Wireless-G ADSL2+ Gateway with VoIP

Setup > ADSL (WAN Connection for PVC) > PPPoE (RFC2516)

Page 13

Chapter 3

Advanced Configuration

Internet Setup

WAN Connection

Select PVC Connection The connection you added is

automatically selected. You can select a different PVC connection to configure.

Connection Type

Connection The connection type is automatically

selected and cannot be changed on this screen.

Follow the instructions for your connection type.

IP Settings for IPoE (RFC2684 Bridged)

Setup > ADSL (WAN Connection for PVC) > IPoE (RFC2684 Bridged)

If your service provider says you are connecting through a dynamic IP address, proceed to the “Automatic IP Address” section. If you are required to use a permanent (static) IP address to connect to the Internet, proceed to the “Static IP Address” section.

Automatic IP Address

Option Tag • Enter the DHCP Option Tag to be included

in the DHCP Sent request.

Option Value • Enter the DHCP Option Value to be

included in the DHCP Sent request. The value must be a hexadecimal string to represent a binary option value. (No check is performed on these values.)

To add the entry, click Add Option. To cancel your changes and return to the ADSL screen, click Back to ADSL Setup.

Request DHCP Options Click this option to configure

the options for DHCP requests. A new window appears.

Obtain an IP Address Automatically > Request DHCP Options

DHCP Option

Request DHCP Options

The options are displayed with the following information: Option Tag and Action. To delete an option, click Delete.

DHCP Option Entry

Obtain an IP Address Automatically Select this option

if your service provider says you are connecting through a dynamic IP address.

Sent DHCP Options Click this option to configure the

options for DHCP Sent requests. A new window appears.

Obtain an IP Address Automatically > Sent DHCP Options

DHCP Option

Sent DHCP Options

The options are displayed with the following information: Option Tag, Option Value, and Action. To delete an option, click Delete.

DHCP Option Entry

Option Tag • Enter the DHCP Option Tag to be included

in the DHCP request.

To add the entry, click Add Option. To cancel your changes and return to the ADSL screen, click Back to ADSL Setup.

Proxy DHCP Options Click this option to configure the

options for DHCP proxy requests. A new window appears.

Obtain an IP Address Automatically > Proxy DHCP Options

DHCP Option

Proxy DHCP Options

The options are displayed with the following information: Option Tag, Option Value, and Action. The read-only Option Value is from the DHCP server on the WAN side. To delete an option, click Delete.

Wireless-G ADSL2+ Gateway with VoIP

Page 14

Chapter 3

Advanced Configuration

DHCP Option Entry

Option Tag • Enter the DHCP Option Tag to be proxyed

to the LAN if it is received from the DHCP server on the WAN side.

To add the entry, click Add Option. To cancel your changes and return to the ADSL screen, click Back to ADSL Setup.

Primary (Required) and Secondary (Optional) DNS Enter the DNS (Domain Name System) server IP

address(es) provided by your service provider. At least one is required.

Static IP Address

Use the following IP Address If you are required to use

a permanent (static) IP address to connect to the Internet, then select this option. Your service provider provides the settings needed for the following fields:

Internet IP Address Enter the Gateway’s IP address, as

seen from the Internet.

Subnet Mask Enter the Gateway’s Subnet Mask, as seen

from the Internet (including your service provider).

Default Gateway Enter the IP address of the service

provider’s server.

Primary (Required) and Secondary (Optional) DNS Enter the DNS (Domain Name System) server IP

address(es) provided by your service provider. At least one is required.

IP Settings for IPoA (RFC2684 Routed)

PPPoE Settings for PPPoE (RFC 2516)

Setup > ADSL (WAN Connection for PVC) > PPPoE (RFC2516)

Primary (Required) and Secondary (Optional) DNS Enter the DNS (Domain Name System) server IP

address(es) provided by your service provider. At least one is required.

Username and Password Enter the Username and

Password provided by your service provider.

Connect on Demand: Max Idle Time You can configure

Keep Alive If you select this option, the Gateway will

periodically check your Internet connection. If you are disconnected, then the Gateway will automatically reestablish your connection. To use this option, select Keep Alive.

Setup > ADSL (WAN Connection for PVC) > IPoA (RFC2684 Routed)

Your service provider provides the settings needed for the following fields:

Internet IP Address Enter the Gateway’s IP address, as

seen from the Internet.

Subnet Mask Enter the Gateway’s Subnet Mask, as seen

from the Internet (including your service provider).

Default Gateway Enter the IP address of the service

provider’s server.

Primary (Required) and Secondary (Optional) DNS Enter the DNS (Domain Name System) server IP

address(es) provided by your service provider. At least one is required.

Wireless-G ADSL2+ Gateway with VoIP

Service Name Enter the Service Name (optional)

provided by your service provider.

PPPoA Settings for PPPoA (RFC 2364)

Setup > ADSL (WAN Connection for PVC) > PPPoA (RFC 2364)

Primary (Required) and Secondary (Optional) DNS Enter the DNS (Domain Name System) server IP

address(es) provided by your service provider. At least one is required.

Username and Password Enter the Username and

Password provided by your service provider.

Page 15

Chapter 3

Advanced Configuration

Connect on Demand: Max Idle Time You can configure

Keep Alive If you select this option, the Gateway will

periodically check your Internet connection. If you are disconnected, then the Gateway will automatically reestablish your connection. To use this option, select Keep

Alive.

Service Name Enter the Service Name (optional)

provided by your service provider.

All connection types use the following settings:

NAT To use Network Address Translation, keep the default

Enabled. Otherwise, select Disabled.

IGMP Forwarding Select Enabled, if you want to allow

multicast traffic through the Router for your multimedia application devices. Otherwise, keep the default, Disabled.

Optional Settings (Advanced View)

MTU Size Keep this value in the 1200 to 1500 range. The

default MTU is configured automatically.

Override MAC Address Select this option to override the

MAC address of this connection.

MAC Address If the Override MAC Address option is

enabled, enter the MAC address you want to use.

Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes. To remove the connection, click Delete Connection.

Setup > Ethernet

Configure the Gateway’s Ethernet settings on this screen.

There are two views available, Basic and Advanced. The default view is Basic. To display the Advanced View, click

Advanced View. To return to the Basic View, click Basic View.

Dedicate The Connection To Voice (FXS1/FXS2) Select

Enabled, if you want to use this connection for FXS1/

FXS2 outbound phone calls. (You can enable this option for only one Internet connection.) Otherwise, keep the default, Disabled.

VLAN ID Mark (Advanced View) Enter the 802.1Q VLAN

ID Mark to be used on egress to the interface associated with this connection. A value of -1 indicates no VLAN tagging for this connection. The default is -1.

802.1p Mark (Advanced View) Enter the 802.1p

(Ethernet priority) Mark to be used on traffic sent out on this connection. A value of -1 indicates no change from the incoming packet. The default is -1.

Override Ethernet Priority (Advanced View) If this

RIP Recv Packet Version (Advanced View) Select the

Routing Information Protocol (RIP) version you want to use: RIP off, RIPv1, or RIPv2.

Setup > Ethernet > Automatic Configuration - DHCP (Advanced View)

Ethernet Setup

5th Ethernet Port

Ethernet Connection To use the fifth Ethernet port

as a WAN port, select Use as WAN Port. To use the fifth Ethernet port as a Local Area Network (LAN) port, select

Use as LAN Port.

NOTE: If you use the fifth Ethernet port as a

WAN port, then the ADSL port is automatically disabled, and all routing goes to other Ethernet ports.

Domain Name (Advanced View) Enter the Domain

Name for this connection. The DNS proxy will compare Domain Names to choose the connection that will send out DNS queries.

Wireless-G ADSL2+ Gateway with VoIP

Ethernet WAN Setup

If you selected Use as WAN Port, the Ethernet WAN Setup settings will be available.

Page 16

Chapter 3

Advanced Configuration

Set Connection Shaping To disable QoS Shaping, select

No Shaping. To shape according to link speed, select Auto (link speed). To manually enter the shape rate,

select Manual, and then enter the number of kbps in the field provided.

NOTE: You can configure the hierarchical shaping

rate on the PVC link level or layer 3 connection level. Usually shaping is configured on the PVC link level, matching the service provider’s upstream speed, to help enforce QoS rules and avoid packet dropping in the service provider’s head-end device (for example, DSLAM).

Select the connection you want to use: Automatic Configuration - DHCP, Static IP, or PPPoE.

Automatic Configuration - DHCP

If your service provider supports DHCP or you are connecting through a dynamic IP address, select Automatic Configuration - DHCP (this option usually applies to cable connections).

Static IP

Static DNS 1 (Required) and 2 (Optional) DNS Enter the

DNS (Domain Name System) server IP address(es) provided by your service provider. At least one is required.

PPPoE

Setup > Ethernet > PPPoE (Advanced View)

Setup > Ethernet > Static IP (Advanced View)

If you are connecting through a static IP address, select

Static IP. Then configure the following:

Internet IP Address Enter the Gateway’s IP address, as

seen from the Internet.

Subnet Mask Enter the Gateway’s Subnet Mask, as seen

from the Internet (including your service provider).

Default Gateway Enter the IP address of the service

provider’s server.

If you are using a PPPoE connection, select PPPoE (this option usually applies to DSL connections). Then configure the following:

Username and Password Enter the Username and

Password provided by your service provider.

Connect on Demand: Max Idle Time You can configure

Keep Alive If you select this option, the Gateway will

periodically check your Internet connection. If you are disconnected, then the Gateway will automatically reestablish your connection. To use this option, select Keep

Alive.

Service Name (Advanced View) Enter the Service Name

(optional) provided by your service provider.

NAT (Advanced View) To use Network Address

Translation, keep the default Enabled. Otherwise, select Disabled.

IGMP Forwarding (Advanced View) Select Enabled, if

you want to allow multicast traffic through the Router for

Wireless-G ADSL2+ Gateway with VoIP

Page 17

Chapter 3

your multimedia application devices. Otherwise, keep the default, Disabled.

VLAN ID Mark (Advanced View) Enter the 802.1Q VLAN

ID Mark to be used on egress to the interface associated with this connection. A value of -1 indicates no VLAN tagging for this connection. The default is -1.

802.1p Mark (Advanced View) Enter the 802.1p

(Ethernet priority) Mark to be used on traffic sent out on this connection. A value of -1 indicates no change from the incoming packet. The default is -1.

Override Ethernet Priority (Advanced View) If this

RIP Recv Packet Version (Advanced View) Select the

Routing Information Protocol (RIP) version you want to use: RIP off, RIPv1, or RIPv2.

Advanced Configuration

Domain Name (Advanced View) Enter the Domain

Name for this connection. The DNS proxy will compare Domain Names to choose the connection that will send out DNS queries.

Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.

Setup > Local Network

Configure the Gateway’s Local Area Network (LAN) settings on this screen.

There are two views available, Basic and Advanced. The default view is Basic. To display the Advanced View, click

Advanced View. To return to the Basic View, click Basic View.

Setup > Local Network (Advanced View)

Local Network

The Local Network section changes the settings on the network connected to the Gateway’s Ethernet ports. Wireless setup is performed through the Wireless tab.

Router IP

The values for the Gateway’s local IP Address and Subnet Mask are displayed. In most cases, keeping the default values will work.

IP Address The default value is 192.168.1.1.

Subnet Mask The default value is 255.255.255.0.

Network Address Server Settings (DHCP)

The settings allow you to configure the Gateway’s Dynamic Host Configuration Protocol (DHCP) server function. The Gateway can be used as a DHCP server for your network. A DHCP server automatically assigns an IP address to each computer on your network. If you choose to enable the Gateway’s DHCP server option, make sure there is no other DHCP server on your network.

Wireless-G ADSL2+ Gateway with VoIP

DHCP Server A Dynamic Host Configuration Protocol

(DHCP) server automatically assigns an IP address to each computer on your network for you. Unless you already have one, Linksys recommends that you keep the default,

Enabled.

DHCP Options To configure DHCP options (available

if DHCP is enabled), click this option. A new window appears.

Page 18

Chapter 3

Advanced Configuration

DHCP Option

Setup > Local Network > DHCP Option

DHCP Option • Select the appropriate setting.

DHCP Option Value • Enter the appropriate IP address,

which is stored as a binary string on the Gateway. (No check is performed on these values.)

Click Save Settings to apply your changes, or click Go

Back to cancel your changes and return to the Local Network screen.

Conditional Serving To configure the Conditional

Serving Pool settings (available if DHCP is enabled), click this option. A new window appears.

Conditional Serving

Conditional Serving Pool

Enable DHCP Conditional Serving • To enable this

option, select the check box. Otherwise, leave the check box blank.

For each entry, the table lists the following: MAC Address, Vendor Class ID, User Class ID, Client ID, Host Name, Domain Name, IP Address, Precedence, and Action. To delete an entry, click Delete. To configure the DHCP options for an entry, click DHCP Option.

Conditional Serving Entry

Precedence • Enter the Precedence value. A lower

value indicates higher priority.

MAC Address • Enter the MAC Address, if applicable as

a filter condition.

Vendor Class ID • Enter the Vendor Class ID, if applicable

as a filter condition.

User Class ID • Enter the User Class ID, if applicable as

a filter condition.

Client ID • Enter the Client ID, if applicable as a filter

condition. This field accepts ASCII or hexadecimal strings. To enter a hexadecimal string, add Ox before the string.

Host Name • Enter the Host Name, if applicable as a

filter condition.

Domain Name • If there is a match, the DHCP server

will assign this Domain Name to the host.

IP Address • If there is a match, the DHCP server will

assign this IP Address to the host.

Click Add Entry to add a new entry to the table. Click Save Settings to apply your changes. Click Back to LAN Setup to return to the Local Network screen.

Setup > Local Network > Conditional Serving

Wireless-G ADSL2+ Gateway with VoIP

Starting IP Address Enter a value for the DHCP server

to start with when issuing IP addresses. Because the Gateway’s default IP address is 192.168.1.1, the Starting IP Address must be 192.168.1.2 or greater, but smaller than

192.168.1.253. The default is 192.168.1.64.

Ending IP Address Specify the final IP address of the range

available for assignment. The default is 192.168.1.253.

Client Lease Time The Client Lease Time is the amount

of time a network device will be allowed connection to the Gateway with its current dynamic IP address. Enter the number of minutes that the device will be “leased” this dynamic IP address. After the time is up, the device will be automatically assigned a new dynamic IP address. The default is 1440 minutes.

DNS Proxy (Advanced View) The Domain Name System

(DNS) is how the Internet translates domain or website names into Internet addresses or URLs. To use DNS Proxy, keep the default, Enable. Otherwise, select Disable.

Page 19

Chapter 3

Advanced Configuration

Static DNS 1-3 (Advanced View) These entries are valid

only when the DNS Proxy option is disabled. At least one DNS server IP address is provided by your service provider. You can enter up to three DNS server IP addresses here. The Gateway will use these for quicker access to functioning DNS servers.

WINS (Advanced View) The Windows Internet Naming

Service (WINS) converts NetBIOS names to IP addresses. If you use a WINS server, enter that server’s IP address here. Otherwise, leave this field blank.

Domain Name (Advanced View) Enter the Domain

Name of your local network.

Reserved IP List (Advanced View) Enter the IP addresses

you want to reserve, so they will not be leased to DHCP clients.

Advanced DHCP Settings (Advanced View)

DHCP Address This option defines the DHCP address

allocation method. To assign local IP addresses from the DHCP pool you have defined, keep the default, Use DHCP Pool.

To have the local network devices share the WAN subnet address, select Use WAN Subnet. In this passthrough mode, the local computers get WAN-side IP addresses. They bypass NAT and are visible on the service provider’s network. However, these computers can still communicate with other computers that are allocated private IP addresses.

To have a local network device share the WAN IP address, select Share WAN IP. In this mode, which is also known as super-DMZ mode, a single computer bypasses NAT. You can specify the computer’s MAC address in the MAC Address field.

WAN IP Interface If you selected Use WAN Subnet or

Share WAN IP, select the appropriate WAN IP connection to use.

MAC Address If you selected Share WAN IP, enter the

MAC address of the local network device.

Lease Time Enter the number of seconds you want the

local network device to lease the WAN IP address.

Time Settings (Advanced View)

Time Zone Select the time zone in which your network

functions.

Automatically adjust clock for daylight saving changes Select this option if you want the Gateway to

automatically adjust for daylight saving time.

NTP Server 1/2 Enter the URL (web address) of the

Network Time Protocol (NTP) server you want to use. The default NTP servers are time.nist.gov and clock.isc.org.

Update Time Click this option to immediately synchronize

the Gateway with the NTP server.

Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.

Setup > DDNS

The Gateway offers a Dynamic Domain Name System (DDNS) feature. DDNS lets you assign a fixed host and domain name to a dynamic Internet IP address. It is useful when you are hosting your own website, FTP server, or other server behind the Gateway.

Before you can use this feature, you need to sign up for DDNS service with a DDNS service provider, www.dyndns.org or www.TZO.com. If you do not want to use this feature, keep the default, Disabled.

Setup > DDNS

DDNS

DDNS Service

Disabled/DynDNS.org/TZO.com If your DDNS service is

provided by DynDNS.org, then select DynDNS.org from the drop-down menu. If your DDNS service is provided by TZO, then select TZO.com. The features available on the DDNS screen will vary, depending on which DDNS service provider you use.

WAN IP The WAN IP address of the Gateway is displayed.

User/Email Enter the user name or e-mail address for

your account.

Password/Key Enter the password or key for your

account.

Host Name Enter the DDNS URL assigned by the service.

Status The status of the DDNS service connection is

displayed.

Connect To manually trigger an update, click this

button.

Click Save Settings to apply your changes, or click Cancel

Changes to cancel your changes.

Wireless-G ADSL2+ Gateway with VoIP

Page 20

Chapter 3

Advanced Configuration

Setup > Advanced Routing

This screen is used to set up the Gateway’s advanced routing functions. Static Routing sets up a fixed route to another network destination.

Setup > Advanced Routing

Advanced Routing

Routing Table

Gateway This is the IP address of the gateway device that

allows for contact between the Gateway and the remote network or host.

Metric This is the number of hops to each node until

the destination is reached (16 hops maximum). Enter the appropriate Metric. The default is 1.

To save the static route you have configured, click Add

Entry. Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.

Setup > PVC/VLAN Mapping

This advanced screen is used to map the PVCs to the Virtual Local Area Networks (VLANs). When you create a mapping, a layer 2 bridge is formed between the Gateway’s LAN port (including WLAN SSID) and WAN port (PVC or Ethernet WAN).

You should configure this screen according to your service provider’s instructions. For example, when Ethernet port 1 is connected to a setup box, a PVC mapping is created for Ethernet port 1 and PVC 1 with VLAN 1002. Traffic is marked with the configured VLAN ID when it travels to the service provider’s network.

For each route, the Destination LAN IP address, Subnet Mask, Gateway, and Metric are displayed. In the Action column, click Delete to delete a static route.

Default Interface The default Layer 3 connection is

displayed.

Default Gateway The default next-hop gateway of the

default interface is displayed.

Default Connection This advanced setting usually

indicates the default connection since the Gateway supports multiple WAN connections. If the Gateway has multiple connections, specify which one is the default.

Static Routing

A static route is a pre-determined pathway that network information must travel to reach a specific host or network. Enter the information described below to set up a new static route.

NOTE: When you add a static route, certain rules

apply. For example, the Gateway must belong to the subnet of any of the router’s interfaces.

Setup > PVC/VLAN Mapping

PVC VLAN Mapping

Select PVC Connection Select the PVC you want to

map.

Destination IP Address The Destination IP Address is

the IP address of the remote network or host to which you want to assign a static route.

Subnet Mask The Subnet Mask determines which

portion of a Destination IP Address is the network portion, and which portion is the host portion.

Wireless-G ADSL2+ Gateway with VoIP

VLAN Bridge Table

For each entry, the table lists the following: LAN Ports, VLAN ID, 802.1p, MAC Address, Ethernet Frame, Enable status, and Action. To delete an existing PVC/VLAN mapping, click Delete.

Page 21

Chapter 3

VLAN Bridge Entry

Enabled Select Enabled to enable the mapping rule.

VLAN ID Enter the VLAN you want to map. The default

is 2.

MAC Address Enter the packet’s source MAC address, if

applicable as a filter condition.

802.1p Enter the priority level for each port. These are

the mappings to 802.1p:

6 High (highest, EF) •

5 Medium (CS) •

Advanced Configuration

4 Normal (CS) •

0 Low (best effort) •

-1 No Change (no change to the original 802.1p • value)

Linksys recommends the following:

For voice and video traffic, enter • 6.

For gaming or mission-critical traffic, enter • 5.

For normal traffic, enter • 4.

For low-priority traffic, enter • 0.

LAN Ports Every LAN interface is listed, including

the Ethernet ports and Wireless Local Area Network (WLAN) ports. (The WLAN ports are listed with their wireless network names, also known as SSIDs.) Select the appropriate LAN interface. For multiple selection, press the Ctrl or Shift key. To deselect, use Ctrl + click (click the selection).

Ethernet Frame The Ethernet frame types are listed.

Select the packet’s Ethernet frame type, if applicable as a filter condition. For multiple selection, press the Ctrl or Shift key. To deselect, use Ctrl + click (click the selection).

Click Add VLAN Bridge to create a new PVC/VLAN mapping, or click Cancel Changes to cancel your changes.

Wireless > Basic Settings

The basic settings for wireless networking are set on this screen.

Wireless > Basic Settings

There are two ways to configure the Gateway’s wireless settings, manual and Wi-Fi Protected Setup. For manual configuration, use this screen to change the settings.

Wi-Fi Protected Setup is a feature that makes it easy to set up your wireless network. If you have devices that support Wi-Fi Protected Setup, then click the Wi-Fi Protected Setup tab, and follow the on-screen instructions (refer to the “Wireless > Wi-Fi Protected Setup” section for more information).

NOTE: Wi-Fi Protected Setup can only be used

for the default wireless network. (The Gateway supports up to four wireless networks. The other three can be configured using the Gateway’s web-based utility.)

Wireless Network

Wireless Channel Select the channel you want to use.

All devices in your wireless network must use the same channel in order to communicate.

Wireless Network State Select the wireless standards

running on your network. If you have Wireless-G and Wireless-B devices in your network, keep the default, Mixed. If you have only Wireless-G devices, select G-Only. If you have only Wireless-B devices, select B-Only. If you do not have any wireless devices, select Disabled.

The Gateway supports up to four wireless networks. By default, only the first wireless network is enabled. On the Wireless Security and MAC Filter screens, you can configure different security settings and MAC filtering rules for each wireless network.

Wireless-G ADSL2+ Gateway with VoIP

Configure the following settings for each wireless network (SSID1-4):

Wireless Network Name (SSID) The network name is

case-sensitive and must not exceed 32 characters (use any of the characters on the keyboard). Linksys recommends that you change the default name of the first network,

linksys1, to a unique name of your choice.

Page 22

Chapter 3

Advanced Configuration

Wireless Network State If you want to use the wireless

network, select Enabled. Otherwise, select Disabled.

Wireless SSID Broadcast When wireless devices survey

the local area for wireless networks to associate with, they will detect the wireless network name or SSID broadcast by the Gateway. If you want to broadcast the Gateway’s SSID, keep the default, Enabled. Otherwise, select Disabled.

Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.

Wireless > Security

The Security screen configures the security of your wireless network(s). The Gateway supports the following wireless security mode options: WPA2-Personal, WPAPersonal, WEP, WPA-Enterprise, and WPA2-Enterprise. (WPA stands for Wi-Fi Protected Access, which is a security standard stronger than WEP encryption, and WEP stands for Wired Equivalent Privacy.) For detailed instructions on configuring wireless security for the Gateway, refer to “Chapter 2: Wireless Security”.

NOTE: If you used Wi-Fi Protected Setup to

configure your wireless network(s), then wireless security has already been set up. Do not make changes to the Wireless Security screen.

WPA2-Personal

Security Mode > WPA2-Personal

Mixed Mode Select Enabled to support both WPA and

WPA2 clients. Otherwise, keep the default, Disabled.

Encryption Select the appropriate method, AES or TKIP

or AES.

Passphrase Enter a Passphrase (also called a WPA shared

key) of 8-63 characters.

Key Renewal Enter a Key Renewal period, which instructs

the Gateway how often it should change the encryption keys. The default is 3600 seconds.

Wireless Security

Wireless Network Select the wireless network you want

to configure.

Security Mode Select the security method for your

wireless network. Proceed to the appropriate instructions. If you do not want to use wireless security, keep the default, Off.

NOTE: If you are using wireless security,

remember that each device in your wireless network MUST use the same security method and settings, or else the wireless devices cannot communicate.

WPA-Personal

Security Mode > WPA-Personal

Encryption TKIP is automatically selected.

Passphrase Enter a Passphrase (also called a WPA shared

key) of 8-63 characters.

Key Renewal Enter a Key Renewal period, which instructs

the Gateway how often it should change the encryption keys. The default is 3600 seconds.

Wireless-G ADSL2+ Gateway with VoIP

Page 23

Chapter 3

Advanced Configuration

WEP

Security Mode > WEP

Encryption Select a level of WEP encryption, 40/64-bit

(10 hex digits) or 104/128-bit (26 hex digits).

Passphrase Enter a Passphrase to automatically generate

WEP keys. Then click Generate.

NOTE: The WEP Passphrase is compatible with

Linksys wireless products only. If you are using non-Linksys products, manually enter the appropriate WEP key on those devices.

RADIUS Server Enter the IP address of the RADIUS

server.

RADIUS Port Enter the port number of the RADIUS

server. The default value is 1812.

Shared Key Enter the key shared between the Gateway

and the server.

Key Renewal Enter a Key Renewal period, which instructs

the Gateway how often it should change the encryption keys. The default is 3600 seconds.

WPA2 Enterprise

This option features WPA2 used in coordination with a RADIUS server. (It should only be used when a RADIUS server is connected to the Gateway.)

Key 1-4 If you did not enter a Passphrase, enter the WEP

key(s) manually.

TX Key Select which TX (Transmit) Key to use. The default

is 1.

WPA Enterprise

This option features WPA used in coordination with a RADIUS server. (RADIUS stands for Remote Authentication Dial-In User Service. This option should only be used when a RADIUS server is connected to the Gateway.)

Security Mode > WPA Enterprise

Security Mode > WPA2 Enterprise

Mixed Mode Select Enabled to support both WPA and

WPA2 clients. Otherwise, keep the default, Disabled.

Encryption Select the appropriate method, AES or TKIP

or AES.

RADIUS Server Enter the IP address of the RADIUS

server.

RADIUS Port Enter the port number of the RADIUS

server. The default value is 1812.

Shared Key Enter the key shared between the Gateway

and the server.

Key Renewal Enter a Key Renewal period, which instructs

the Gateway how often it should change the encryption keys. The default is 3600 seconds.

Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.

Wireless > MAC Filter

Wireless access can be filtered by using the MAC addresses of the wireless devices transmitting within your network’s radius.

Encryption TKIP is automatically selected.

Wireless-G ADSL2+ Gateway with VoIP

Page 24

Chapter 3

Advanced Configuration

NOTE: Wi-Fi Protected Setup can only be

used for the default wireless network. (The Gateway supports up to four wireless networks. The other three can be configured using the Wireless > Basic Settings screen of the Gateway’s web-based utility.)

Wireless > MAC Filter

Wireless MAC Filter

Select Wireless Network (SSID) Select the wireless

network you want to configure.

Enabled/Disabled To use the wireless MAC filter, select

Enabled. Otherwise, keep the default, Disabled.

MAC Address Filter

Filter As White List/Filter As Black List

network devices with the MAC addresses on this list, select Filter As White List. To block access by network devices with the MAC addresses on this list, keep the default, Filter As

Black List

MAC 01-20 Enter the MAC addresses of the devices

whose wireless access you want to block or allow.

For each wireless device, its MAC address and connection status are listed. To copy a MAC address to one of the MAC 01-20 fields, click Copy.

Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.

To allow access by

Wireless > Wi-Fi Protected Setup

There are two ways to configure the Gateway’s wireless settings, manual and Wi-Fi Protected Setup. For manual configuration, click the Basic Settings tab (refer to the “Wireless > Basic Settings” section for more information).

Wi-Fi Protected Setup is a feature that makes it easy to set up your wireless network. If you have devices that support Wi-Fi Protected Setup, then use the following instructions.

Wireless > Wi-Fi Protected Setup

Wi-Fi Protected Setup

If you have client devices, such as a wireless adapter, that supports Wi-Fi Protected Setup, then you can use Wi-Fi Protected Setup to automatically configure wireless security for your wireless network(s).

There are three methods available. Use the method that applies to the client device you are configuring.

NOTE: Wi-Fi Protected Setup configures one

client device at a time. Repeat the instructions for each client device that supports Wi-Fi Protected Setup.

Method #1

Use this method if your client device has a Wi-Fi Protected Setup button.

Click or press the1. Wi-Fi Protected Setup button on the client device. (If Wi-Fi Protected Setup is an on-screen option, then select it.)

Click the 2. Wi-Fi Protected Setup button on this screen.

After the client device has been configured, click 3. OK. Then refer back to your client device or its documentation for further instructions.

Wireless-G ADSL2+ Gateway with VoIP

Page 25

Chapter 3

Method #2

Use this method if your client device has a Wi-Fi Protected Setup PIN number.

Enter the client PIN number in the1. PIN field on this screen (the Gateway’s Wi-Fi Protected Setup screen).

Click 2. Register.

Method #3

Use this method if your client device asks for the Router’s PIN number.

Enter the PIN number listed on this screen. (It is also 1. listed on the label on the bottom of the Router.)

After the client device has been configured, click 2. OK. Then refer back to your client device or its documentation for further instructions.

At the bottom of the screen, status information for your wireless security is displayed:

Wi-Fi Protected Setup Simple-Config-State The status

of the Wi-Fi Protected Setup feature is displayed. The default is Not configured. After the Router has been configured, the status changes to “Configured”.

Network Name (SSID) The name of the wireless network

is displayed.

Security The security method of the wireless network is

displayed.

Encryption The encryption method, such as TKIP or AES,

is displayed.

Passphrase The passphrase for the wireless security

method is displayed. It acts like a password for access to the wireless network. (For WPA security methods, the passphrase is also known as a WPA shared key.)

NOTE: If you have client devices that do not

support Wi-Fi Protected Setup, note the wireless settings, and then manually configure those client devices.

Wireless > Advanced Settings

Use this screen to set up the Gateway’s advanced wireless settings, which apply to all of the Gateway’s wireless networks. These settings should only be adjusted by an expert administrator as incorrect settings can reduce wireless performance.

Advanced Configuration

Wireless > Advanced Settings

Advanced Wireless

Basic Rate The Basic Rate setting is not actually one rate

of transmission but a series of rates at which the Gateway can transmit. The Gateway will advertise its Basic Rate to the other wireless devices in your network, so they know which rates will be used. The Gateway will also advertise that it will automatically select the best rate for transmission. Select the appropriate option: Default, for transmission at all standard wireless rates; 1-2Mbps, for use with older wireless technology; All, for transmission at all wireless rates; or Wi-Fi Alt. For the Wi-Fi Alt option, basic rates are 1, 2, 5.5, 6, 11, 12, and 24 Mbps; supported rates are 9, 18, 36, 48, and 54 Mbps. If you are not sure which rate to select, keep the default, Default.

CTS Protection Mode CTS (Clear-To-Send) Protection

Mode’s default is Disabled. Select Auto if you want the device to automatically use CTS Protection Mode when your Wireless-G products are experiencing severe problems and are not able to transmit to the device in an environment with heavy 802.11b traffic. This function boosts the device’s ability to catch all Wireless-G transmissions but will severely decrease performance.

Control TX Rate The Control TX Rate should be set

depending on the speed of your wireless network. Select from a range of transmission speeds, or keep the default, Auto. When the Auto setting is selected, the Gateway automatically uses the fastest possible data rate and enables the Auto-Fallback feature, which negotiates the best possible connection speed between the Gateway and a wireless device.

Wireless Afterburner To improve wireless performance

when the Gateway is used with devices that support SpeedBooster, select Enable. Otherwise, keep the default,

Disable.

Wireless-G ADSL2+ Gateway with VoIP

Beacon Interval Enter a value between 1 and 65,535

milliseconds. The Beacon Interval value indicates the frequency interval of the beacon. A beacon is a packet broadcast by the Gateway to synchronize the wireless network(s). The default value is 100.

Page 26

Chapter 3

Advanced Configuration

DTIM Interval This value, between 1 and 255, indicates

the interval of the Delivery Traffic Indication Message (DTIM). A DTIM field is a countdown field informing clients of the next window for listening to broadcast and multicast messages. When the Gateway has buffered broadcast or multicast messages for associated clients, it sends the next DTIM with a DTIM Interval value. Its clients hear the beacons and awaken to receive the broadcast and multicast messages. The default value is 1.

Fragmentation Threshold This value specifies the

maximum size for a packet before data is fragmented into multiple packets. If you experience a high packet error rate, you may slightly increase the Fragmentation Threshold. Setting the Fragmentation Threshold too low may result in poor network performance. Only minor reduction of the default value is recommended. In most cases, it should remain at its default value of 2346.

RTS Threshold Should you encounter inconsistent

data flow, only minor reduction of the default, 2346, is recommended. If a network packet is smaller than the preset RTS threshold size, the RTS/CTS mechanism will not be enabled. The Gateway sends Request to Send (RTS) frames to a particular receiving station and negotiates the sending of a data frame. After receiving an RTS, the wireless station responds with a Clear to Send (CTS) frame to acknowledge the right to begin transmission. The RTS Threshold value should remain at its default value of

2346.

NOTE: If the Gateway was provided by your

service provider, then it may restrict access to the Admin View of the Voice screens in the web-based utility. Contact your service provider for the admin login.

Voice > Info

The Info screen displays Voice over Internet Protocol (VoIP) information about the Gateway. (The User and Admin Views are the same for this screen.)

WMM Support The Gateway supports Wi-Fi Multimedia

(WMM) for Quality of Service (QoS). When WMM Support is enabled, it provides four priority queues for different types of traffic. It automatically maps the incoming packets to the appropriate queues based on QoS settings (in the IP or layer 2 header). WMM provides the capability to prioritize traffic in your environment. If you have other devices on your network that support WMM, select

Enable. Otherwise, keep the default, Disable.

Auto Power Save Delivery Unscheduled Automatic

Power Save Delivery (UAPSD) is a special power-saving mode to achieve end-to-end QoS. This option is available if you enabled WMM Support. To use the power save feature, select Auto Power save Delivery.

Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.

Voice

There are two views available, User and Admin. The default view is User. To display the Admin View, click Admin View. If you are prompted for the admin login, enter your admin name and password. To return to the User View, click User View.

Voice > Info

VoIP

Wireless-G ADSL2+ Gateway with VoIP

RTP Packets Sent The number of RTP packets sent by the

Gateway is displayed.

Page 27

Chapter 3

Advanced Configuration

RTP Bytes Sent The number of RTP bytes sent by the

Gateway is displayed.

RTP Packets Recv The number of RTP packets received

by the Gateway is displayed.

RTP Bytes Recv The number of RTP bytes received by the

Gateway is displayed.

SIP Messages Sent The number of SIP messages sent by

the Gateway is displayed.

SIP Bytes Sent The number of SIP bytes sent by the

Gateway is displayed.

SIP Messages Recv The number of SIP messages received

by the Gateway is displayed.

SIP Bytes Recv The number of SIP bytes received by the

Gateway is displayed.

External IP The external IP address used for NAT mapping

is displayed.

Line 1/2 Status

Lines 1 and 2 have the same status information available.

Hook State The status of the Internet phone line’s

readiness is displayed. “On” indicates that it is ready for use, while “Off” indicates that it is in use.

Registration State The status of the line’s registration

with the Internet Telephony Service Provider (ITSP) is displayed.

Hazardous Potential The amount of hazardous potential

is displayed.

Last Registration At The last date and time the line was

registered are displayed.

Foreign Voltage The amount of foreign voltage is

displayed.

Next Registration In The number of seconds until the

next registration is displayed.

Diff Resistive Fault The amount of differential resistive

fault is displayed.

Message Waiting This indicates whether you have new

voicemail waiting.

Long Resistive Fault The amount of long resistive fault

is displayed.

Call Back Active This indicates whether a call back

request is in progress.

REN The Ringer Equivalence Number (REN) is displayed.

Last Called Number The last number called is displayed.

Last Caller Number The number of the last caller is

displayed.

Mapped SIP Port The port number of the NAT mapped

SIP port is displayed.

Wireless-G ADSL2+ Gateway with VoIP

Calls 1 and 2 have the same status information available.

Call 1/2 State The status of the call is displayed.

Call 1/2 Tone The type of tone used by the call is

displayed.

Call 1/2 Encoder The codec used for encoding is

displayed.

Call 1/2 Decoder The codec used for decoding is

displayed.

Call 1/2 FAX The status of the fax pass-through mode is

displayed.

Call 1/2 Type The direction of the call is displayed.

Call 1/2 Remote Hold This indicates whether the far end

has placed the call on hold.

Call 1/2 Callback This indicates whether the call was

triggered by a call back request.

Call 1/2 Peer Name The name of the internal phone is

displayed.

Call 1/2 Peer Phone The phone number of the internal

phone is displayed.

Call 1/2 Duration The duration of the call is displayed.

Call 1/2 Packets Sent The number of packets sent is

displayed.

Call 1/2 Packets Recv The number of packets received

is displayed.

Call 1/2 Bytes Sent The number of bytes sent is

displayed.

Call 1/2 Bytes Recv The number of bytes received is

displayed.

Call 1/2 Decode Latency The number of milliseconds for

decoder latency is displayed.

Call 1/2 Jitter The number of milliseconds for receiver

jitter is displayed.

Call 1/2 Round Trip Delay The number of milliseconds

for delay is displayed.

Call 1/2 Packets Lost The number of packets lost is

displayed.

Call 1/2 Packet Error The number of invalid packets

received is displayed.

Call 1/2 Mapped RTP Port The number of the NAT

mapped RTP port is displayed.

PSTN Line Status

PSTN Hook State The status of the PSTN phone line’s

readiness is displayed. “On” indicates that it is ready for use, while “Off” indicates that it is in use.

PSTN Line Voltage The tip-to-ring voltage of the Line

(FXO) port is displayed.

Page 28

Chapter 3

PSTN Loop Current The loop current to the Line (FXO)

port is displayed.

Voice > System

The System screen displays system settings. (The User View only accesses the User Password setting.)

Voice > System (User View)

VoIP

Advanced Configuration

System Configuration

User Password Enter the password for user access to the

Voice screens. (By default, there is no password.)

Miscellaneous Settings

No miscellaneous settings are displayed.

Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.

Voice > User1/2

The User1 and 2 screens display similar settings. The User1 screen displays settings for users of phone line 1, and the User2 screen displays settings for users of phone line 2. (The User and Admin Views are the same for this screen.)

Voice > User1

VoIP

Call Forward Settings

Enter the call forwarding numbers you want to use.

Cfwd All Dest Enter the number for the Call Forward All

Service feature (when you want to forward all calls).

Cfwd Busy Dest Enter the number for the Call Forward

Busy feature (when the line is busy).

Cfwd No Ans Dest Enter the number for the Call Forward

No Answer feature (when the line is not answered).

Cfwd No Ans Delay Enter the number of seconds to wait

before the Call Forward No Answer feature is triggered. The default is 20.

Wireless-G ADSL2+ Gateway with VoIP

Selective Call Forward Settings

Enter the caller numbers that will be forwarded to specific phone numbers.

Cfwd Sel1-8 Caller Enter the caller number pattern to

trigger the Call Forward Selective (1-8) feature.

Cfwd Sel1-8 Dest Enter the forward number for the Call

Forward Selective (1-8) feature.

Page 29

Chapter 3

Advanced Configuration

Cfwd Last Caller Enter the caller number that is actively

forwarded to the Cfwd Last Dest number when the Call Forward Last activation code is used.

Cfwd Last Dest Enter the forward number for the Cfwd

Last Caller feature.

Block Last Caller Enter the ID of the caller blocked via

the Block Last Caller service.

Accept Last Caller Enter the ID of the caller accepted via

the Accept Last Caller service.

Speed Dial Settings

Speed Dial 2-9 Enter the phone number for each Speed

Dial setting.

Supplementary Service Settings

CW Setting Select whether you want to use the Call

Waiting feature for all calls, yes or no. The default is yes.

Block CID Setting Select whether you want to block

Caller ID for all calls, yes or no. The default is no.

Block ANC Setting Select whether you want to block

anonymous calls, yes or no. The default is no.

Storage > Disk Detail

The Disk Detail screen lists the location, Make and Model, Physical Size, and Free Space of the storage device connected to the Gateway’s USB port.

For USB storage, the Gateway supports the following features:

USB 2.0 •

Auto-mounting of external USB hard drive •

FAT/FAT32 file system •

Display of disk information •

File browsing •

File search •

Creation of new directories •

File deletion, copying, moving, or renaming •

File downloads (save files to the computer from USB • storage)

File uploads (save files from the computer to USB • storage)

DND Setting Select whether you want to use the Do Not

Disturb (DND) feature, yes or no. The default is no.

CID Setting Select whether you want to enable Caller ID

generation, yes or no. The default is yes.

CWCID Setting Select whether you want to enable Caller

ID for Call Waiting, yes or no. The default is yes.

Dist Ring Setting Select whether you want to use the

Distinctive Ring feature, yes or no. The default is yes.

Message Waiting Select whether you want to use the

Message Waiting feature, yes or no. The default is no.

Distinctive Ring Settings

Ring1-8 Caller Enter the caller number pattern to play

Distinctive Ring/Call Waiting Tone (1-8).

Ring Settings

Default Ring Select the default ringing pattern for all

callers. The default is 1.

Default CWT Select the default CWT pattern for all callers.

The default is 1.

Hold Reminder Ring Select the ring pattern that will

remind you of a call on hold when the phone is on-hook. The default is 8.

Storage > Disk Detail

Disk Detail

Click Refresh to update the on-screen information.

Storage > Disk Management

The Disk Management screen allows you to search and manage the storage device connected to the Gateway’s USB port.

Call Back Ring Select the ring pattern for call back

notification. The default is 7.

Click Save Settings to apply your changes, or click Cancel

Changes to cancel your changes.

Wireless-G ADSL2+ Gateway with VoIP

Page 30

Chapter 3

Advanced Configuration

Security > Firewall

The Firewall screen is used to configure a firewall that can filter out various types of unwanted traffic on the Gateway’s local network.

Security > Disk Management

Disk Management

Select Disk Select the storage location.

Current Location The location of the current directory is

displayed.

Current Directory The number of files is displayed.

Search Enter the term you want to look for in the current

directory, and then click Search.

New Directory To create a new directory, click New

Directory, and follow the on-screen instructions.

Upload File To upload a file to the current directory,

select it from the list, and then click Upload File. To upload all files in the current directory, select Select All.

The files are displayed with the following information: Type, Name, Size, and Modified Date.

Click Refresh to update the on-screen information.

To delete a file or directory, select it and then click Delete. To copy a file or directory to a new location, select it and then click Copy. To move a file or directory to a new location, select it and then click Move. To rename a file or directory, select it and then click Rename.

Security > Firewall

Firewall

Intrusion Detection Protection To use Intrusion

Detection System (IDS) and Denial of Service (DoS) protection, select Enabled. Otherwise, keep the default,

Disabled.

Web Content Filtering To filter web content, keep the

default, Enabled. Otherwise, select Disabled. (This feature must be enabled to use the Website Blocking options on the Access Restrictions > Internet Access Policy screen.)

Max Firewall Sessions Enter the maximum number of

firewall sessions that will be processed at any given time.

Max QoS Sessions Enter the maximum number of QoS

sessions that will be processed at any given time.

SIP ALG The SIP ALG feature assists VoIP phones behind

the Gateway when NAT problems are encountered. This feature also assists QoS (when enabled) with automatic classification of SIP- and RTP-related traffic. To use the SIP ALG feature, keep the default, Enabled. Otherwise, select Disabled.

Firewall Profile

NOTE: If you have DDNS service, you can

manage the storage device using the WAN IP address. To allow WAN HTTP access, you must enable remote access on the Administration > Management screen and disable the firewall on the Security > Firewall screen.

Wireless-G ADSL2+ Gateway with VoIP

Apply Firewall Profile For a low level of firewall

protection, keep the default, Low. For a high level of firewall protection, select High. To disable the firewall, select Off.

To configure user-based security rules, click Access Restrictions. (Refer to the “Access Restrictions > Internet Access Policy” section for details.)

Click Save Settings to apply your changes, or click Cancel

Changes to cancel your changes.

Page 31

Chapter 3

Advanced Configuration

Access Restrictions > Internet Access Policy

The Internet Access Policy screen allows you to block or allow specific kinds of Internet usage and traffic, such as Internet access, designated services, and websites during specific days and times.

Access Restriction

Deny/Allow Select the appropriate option, Deny or

Allow, depending on whether you want to block or allow

Internet access.

Website Blocking by Keyword

You can block websites that use specific keywords in their URL addresses. Enter each keyword in a separate field. (You can also enter a specific URL address.)

Regular Expression

A regular expression is a string used to describe or match a set of strings. You can block websites that use strings encompassed by the regular expressions you enter on this screen. Enter each regular expression in a separate field.

Regular Expression Syntax

. any character

^ start of a line

$ end of a line

* match zero or many times

Access Restrictions > Internet Access Policy

Internet Access Policy

You can use a policy to manage a computer’s access. Use the settings on this screen to establish an access policy (after Add Rule is clicked).

Access Policy Table

The policies are displayed with the following information: Name, Service, Web, Schedule, and Action. To delete a policy, click Delete.

Access Policy Rule

Internet Access Policy Select Add New to add a new

policy, or select a policy to display or edit its settings.

NOTE: Multiple rules can be created for the

same computer. Rules have priorities, so the first matched rule determines the computer’s access policy.

? match zero or one time

+ match one or more times

{m,n} match from m to n times (m <= n)

{n} match exactly n times

[a-c] character set

[^a-c] negative charset

| or

(“ and “) brackets for grouping

\xx escaped character

Blocked Services

You can filter access to various services accessed over the Internet, such as FTP or telnet.

From the Blocked Services list, select the service(s) you want to block. For multiple selection, press the Ctrl or Shift key. To deselect, use Ctrl + click (click the selection).

If the service you want is not listed, click Service. (Refer to the “Applications & Gaming > Service” section for details.)

Schedule

Status To apply a policy, select Enabled. Otherwise,

select Disabled.

PC (IP or Host Name) Enter the IP address or host name

of the computer.

Wireless-G ADSL2+ Gateway with VoIP

Decide which days and what times you want this policy to be enforced.

Days Select the individual days during which the policy

will be in effect, or select Everyday.

Times Then enter a range of hours and minutes during

which the policy will be in effect, or select 24 Hours.

Page 32

Chapter 3

Advanced Configuration

Click Add Rule to save the policy’s settings. To cancel the policy’s settings, click Cancel Changes.

Applications and Gaming > Single Port Forwarding

The Single Port Forwarding screen allows you to customize port services for common applications on this screen.

When users send these types of requests to your network via the Internet, the Gateway will forward those requests to the appropriate servers (computers). Before using forwarding, you should assign static IP addresses to the designated servers.

Applications and Gaming > Port Range Forwarding

The Port Range Forwarding screen allows you to set up public services on your network, such as web servers, ftp servers, e-mail servers, or other specialized Internet applications. (Specialized Internet applications are any applications that use Internet access to perform functions such as videoconferencing or online gaming. Some Internet applications may not require any forwarding.)

If you need to forward all ports to one computer, click the DMZ tab.

Applications and Gaming > Single Port Forwarding

Single Port Forwarding

To forward a port, enter the information on each line for the criteria required.

Application Select the appropriate application: HTTP

(80), HTTPS (443), FTP (21), Windows Media Player (1755), DNS (53), POP3 (110), Simple Mail Transfer (25), or TR069 Connection Request (888).

Internal Port Enter the internal port number used by

the server or Internet application. Check with the Internet application documentation for more information.

IP Address For each application, enter the IP address of

the computer that should receive the requests.

Enabled For each application, select Enabled to enable

port forwarding.

Click Save Settings to apply your changes, or click Cancel

Changes to cancel your changes.

Wireless-G ADSL2+ Gateway with VoIP

Applications and Gaming > Port Range Forwarding

Port Range Forwarding

To forward a port range, enter the information on each line for the criteria required.

Application Select the appropriate application.

NOTE: If you do not see the application you

want, configure the service on the Applications & Gaming > Service screen.

IP Address For each application, enter the IP address of

the computer running the specific application.

Enabled Select Enabled to enable port forwarding for

the applications you have defined.

Page 33

Chapter 3

Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.

Applications and Gaming > DMZ

The DMZ feature allows one network computer to be exposed to the Internet for use of a special-purpose service such as Internet gaming or videoconferencing. DMZ hosting forwards all the ports at the same time to one PC. The Port Range Forwarding feature is more secure because it only opens the ports you want to have opened, while DMZ hosting opens all the ports of one computer, exposing the computer to the Internet.

Advanced Configuration

Applications and Gaming > Port Range Triggering

Port Range Triggering

To trigger a port range, enter the information on each line for the criteria required.

Applications and Gaming > DMZ

DMZ

Any computer whose port is being forwarded must have its DHCP client function disabled and should have a new static IP address assigned to it because its IP address may change when using the DHCP function.

DMZ To disable DMZ hosting, keep the default, Disabled.

To expose one PC, select Enabled. Then configure the following setting:

DMZ IP Address Enter the IP address of the computer.

Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.

Applications & Gaming > Port Range Triggering

The Port Range Triggering screen allows the Gateway to watch outgoing data for specific port numbers. The IP address of the computer that sends the matching data is remembered by the Gateway, so that when the requested data returns through the Gateway, the data is pulled back to the proper computer by way of IP address and port mapping rules.

Application Name Enter the unique application name of

the trigger.

Port Start ~ Port End For each application, enter the

starting and ending port numbers of the triggering port number range. These are the ports used by initiating traffic. Check with the Internet application documentation for the port number(s) needed.

Protocol For each application, select the appropriate

protocol, TCP(6) or UDP(17).

Forwarded Port Start ~ Forwarded Port End For each

application, enter the starting and ending port numbers of the forwarded port number range. These are the ports used by incoming traffic. Check with the Internet application documentation for the port number(s) needed.

Allow Multiple Hosts Select this option to allow multiple

hosts in returned traffic.

Enabled Select Enabled to enable port triggering for the

applications you have defined.

Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.

Applications and Gaming > QoS

Quality of Service (QoS) ensures better service to high-priority types of network traffic, which may involve demanding, real-time applications, such as videoconferencing.

Wireless-G ADSL2+ Gateway with VoIP

NOTE: The Gateway’s QoS is for upstream traffic

regulation only. Downstream QoS is usually enforced by the service provider’s headend equipment.

Page 34

Chapter 3

Applications and Gaming > QoS

QoS (Quality of Service)

Application-based QoS manages information as it is transmitted and received.

QoS To use QoS, select Enabled. Otherwise, keep the

default, Disabled.

Default Queue Index Select the default queue (and

priority) for applications not specified below: 1-8. (A lower value has higher priority.)

Queue Management A new window appears.

Advanced Configuration

Scheduler • Select the scheduling algorithm: SP, WFQ,

or WRR (Weighted Round Robin). The default is SP.

Dropper • Select the dropping algorithm used if there

is congestion: RED (Random Early Detection), DT (Drop Tail), or WRED (Weighted RED). The default is WRED.

Weight • When WFQ or WRR is used, this option

is available and used only for queues of equal precedence. Queues 4-6 have equal precedence, and Queues 7-8 have equal precedence. Queues 1-3 have higher precedence than Queues 4-6, while Queues 4-6 have higher precedence than Queues 7-8.

Shaping

• If the Shaping rate is greater than or equal to

100, then it is the percentage of physical bandwidth. If the Shaping rate is less than 100, then it is the rate in bits per second. A value of -1 indicates no shaping. The default is -1.

Burst Size • Enter the Burst Size in bytes (1 to 10485760).

For both leaky bucket (constant rate shaping) and token bucket (variable rate shaping) algorithms, the Burst Size value is the bucket size and the maximum burst size. If you set this value to zero, then the Gateway will use the system default Burst Size, which is the current Shaping rate divided by eight. The default is 0.

Applications and Gaming > QoS > Queue Management

Queue Management

Queue Index • There are eight queues for each

interface. You can configure the parameters but cannot add or delete queues.

Higher index queues generally represent higher priority queues. Queues 1-3 are Strict Priority (WP) queues, and Queues 4-8 are priority-based Weighted Fair Queues (WFQ).

Click Save Settings to apply your changes, or click Back to QoS to cancel your changes and return to the QoS screen.

Summary

The QoS rules are displayed with the following information: Port, Filters/Target, Queue Index, Marks and On (status).

To move, edit, or delete a rule, select the entry (its color will change).

Move Up To move a QoS rule up in precedence, click this

option.

Move Top To move a QoS rule to highest in precedence,

click this option.

Move Down To move a QoS rule down in precedence,

click this option.

Move Bottom To move a QoS rule lowest in precedence,

click this option.

Delete To delete a QoS rule, click this option.

Edit Rule To change a QoS rule, click this option.

New Rule To create a new QoS rule, click this option.

If you click Edit Rule or New Rule, a different screen appears.

Precedence • Enter the Precedence value of this queue

relative to the others. A lower value indicates higher precedence.

Wireless-G ADSL2+ Gateway with VoIP

Page 35

Chapter 3

Advanced Configuration

QoS (Quality of Service)

QoS > Add New Rule

Enable • To enable this QoS rule, select the check box.

Otherwise, leave the check box blank.

Classification Sources • Select All Sources, Local

Gateway, All LAN Ports that traffic will come from, or

a specific LAN port: Ethernet Ports 1-5 or WLAN SSID networks. The default is All Sources.

Ethernet Type • Select None, IP (0x0800), ARP

(0x0806), PPPoE Discovery Stage (0x8863), PPPoE Session State (0x8864), or EAPOL (0x888e).

Protocol • If you selected IP (0x0800) for the Ethernet

Type setting, then select the appropriate Protocol: None, ICMP (1), IGMP (2), TCP (6), or UDP (17).

Depending on the Protocol you selected, the following settings may be available:

Destination IP • Enter the Destination IP address, if

applicable as a filter condition.

Destination Subnet Mask • Enter the Destination

subnet mask, if applicable as a filter condition.

Destination Port • If you selected TCP or UDP for the

Protocol setting, enter the Destination port range, if applicable as a filter condition.

Source IP • Enter the Source IP address of the local

computer, if applicable as a filter condition.

Source Subnet Mask • Enter the Source subnet mask,

if applicable as a filter condition.

Source Port • If you selected TCP or UDP for the Protocol

setting, enter the Source port range, if applicable as a filter condition.

Source MAC • Enter the Source MAC address of the

local computer, if applicable as a filter condition.

Source MAC Mask • Enter the Source MAC Mask, if

applicable as a filter condition. If you leave this setting blank, then this mask will be ignored.

Source Vendor Class ID • If applicable as a filter

condition, enter the Source Vendor Class ID in the host’s DHCP request.

Source Client ID • If applicable as a filter condition,

enter the Source Client ID in the host’s DHCP request.

Source User Class ID • If applicable as a filter condition,

enter the Source User Class ID in the host’s DHCP request.

DSCP • If applicable as a filter condition, enter the DSCP

value of the LAN’s incoming packet.

Ethernet Priority • If applicable as a filter condition,

enter the Ethernet Priority of the LAN’s incoming packet.

VLAN ID • If applicable as a filter condition, enter the

VLAN ID of the LAN’s incoming packet.

Ethernet Priority Mark (optional) • To mark outgoing

packets with a specific 802.1p value, enter the value in the field provided.

DSCP Mark (optional) • To mark outgoing packets

with a specific DSCP value, enter the value in the field provided.

Target Interface (optional) • All WAN connections and

PVC/VLAN bridges are listed. Select the appropriate interface. The Gateway will direct matching packets to this outgoing interface.

Queue Index • Traffic priority applies to LAN-to-WAN

traffic only. Higher priority traffic is guaranteed available bandwidth. This is useful for simultaneous activities that put a heavy load on the network (for example, a VoIP phone call during large file downloads). Select the appropriate Queue Index (and priority): 1 High-8 (a lower value means higher priority).

NOTE: Traffic from the Gateway’s voice lines

are automatically assigned highest priority. You can update parameters, such as the Ethernet Priority Mark setting, according to your service provider’s request.

Click Add Rule or Save Rule to save your changes, or click Cancel Changes to cancel your changes and return to the original QoS screen.

Wireless-G ADSL2+ Gateway with VoIP

Page 36

Chapter 3

Advanced Configuration

On the original QoS screen, click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.

Applications and Gaming > Service

The Service screen allows you to add services.

Administration > Management

The Administration > Management screen allows the network’s administrator to manage specific Gateway functions for access and security.

Applications and Gaming > Service

Service/Application

Service Table

The services are displayed with the following information: Service Name, Protocol, Ports/Types, and Action. To delete a user-defined service, click Delete. (Default services cannot be deleted.)

To view additional services, click Extended View. To return to the Basic View, click Basic View.

Service Entry

Service Name Enter a name for the new service.

Protocol Select the appropriate protocol: TCP(6),

UDP(17), ICMP, ESP(50), AH(51), GRE(47), IGMP(2), PIM-DM(103), or IPCOMP(108).

Ports Enter the starting and ending port numbers.

ICMP Type Enter the appropriate number, 1-255, which is

valid only for ICMP.

IGMP Type Enter the appropriate number, 1-255, which

is valid only for IGMP.

Click Add Service to add a new service, or click Cancel Changes to cancel your changes.

Administration > Management

Gateway Access

Local Gateway Access

To ensure the Gateway’s security, you will be asked for your username and password when you access the Gateway’s web-based utility. The default username and password are admin.

Gateway Username Enter the default Gateway

Username, admin.

Gateway Password Linksys recommends that you

change the default Gateway Password, admin, to one of your choice.

Re-enter to Confirm Enter the Gateway Password again

to confirm.

Remote Gateway Access

Remote Management To permit remote access of the

Gateway, from outside the local network, select Enabled. Otherwise, keep the default, Disabled.

Management Port Enter the port number that will be

open to outside access.

Management Protocol Select the appropriate protocol,

HTTP or HTTPS.

Wireless-G ADSL2+ Gateway with VoIP

Page 37

Chapter 3

Advanced Configuration

NOTE: When you are in a remote location

and wish to manage the Gateway, enter

https://<Internet_IP_address>:port or http://<Internet_IP_address>:port. Enter

the Gateway’s specific Internet IP address in place of <Internet_IP_address>, and enter the Management Port number in place of the word port.

Remote User Name Enter the login user name for remote

management.

Remote User Password Enter the login password for

remote management.

IGMP

Internet Group Multicast Protocol (IGMP) is used to establish membership in a multicast group and is commonly used for multicast streaming applications. For example, you may have Internet Protocol Television (IPTV) with multiple setup boxes on the same local network. These setup boxes have different video streams running simultaneously, so you should use the IGMP feature of the Router.

TR64

TR64 is the DSL Forum’s specification for the Gateway’s LAN management through UPnP services.

TR64 To use this option, select Enabled. Otherwise, keep

the default, Disabled.

Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.

Administration > Log

The Gateway can keep logs of traffic and events for your Internet connection.

IGMP Proxy IGMP forwarding (proxying) is a system that

improves multicasting for LAN-side clients. If the clients support this option, keep the default, Enabled. Otherwise, select Disabled.

IGMP Querier Version Select: Version 1, Version 2, or

Version 3. The default is Version 2.

Query Interval This option is valid when IGMP Proxy is

enabled. Enter the number of seconds between queries. The default is 125 seconds.

Querier Immediate Leave Select Enabled, if you use

IPTV applications and want to allow immediate channel swapping or flipping without lag or delays. Otherwise, keep the default, Disabled.

UPnP

Universal Plug and Play (UPnP) allows Windows XP and Vista to automatically configure the Gateway for various Internet applications, such as gaming and videoconferencing.

UPnP If you want to use UPnP, keep the default, Enabled.

Otherwise, select Disabled.

NOTE: IGMPv2 is enabled by default, and v3

is supported. IGMP Snooping is enabled by default for all bridges.

Administration > Log

Reporting

Log To disable the Log function, select Disabled. To

monitor traffic between the network and the Internet, keep the default, Enabled. With logging enabled, you can choose to view temporary logs.

Log Severity Select the severity level of the log events

you want to view: Informational, Warning (default), or Critical.

System Log Server To enable system log server support,

enter the IP address of the system log server. To disable system log server support, leave this setting blank.

Email Alert

Email Alerts (For Warning Events) To enable E-Mail

Alerts for Warning-level events, select Enabled. Otherwise, keep the default, Disabled.

SMTP Mail Server Enter the address (domain name) or

IP address of the Simple Mail Transport Protocol (SMTP) server for outgoing e-mail.

Wireless-G ADSL2+ Gateway with VoIP

User Name Enter the User Name for SMTP

authentication.

Password Enter the Password for SMTP authentication.

Page 38

Chapter 3

Email to Address Enter the e-mail address that will

receive alert logs.

Email From Address Enter the return address for the

e-mail alerts. (This can be a dummy address.)

Event Log

For each log, the Event Log displays the following information: Time, Description, Source Address, and Destination Address.

Click Save Settings to apply your changes. Click Clear Event Log to clear all of the events. Click Refresh to update the on-screen information.

Advanced Configuration

Administration > Backup

Administration > Diagnostic

The ping test allows you to check the connections of your network devices, including connection to the Internet.

Administration > Diagnostic

Ping Test

Ping Test Parameters

The ping test checks the status of a connection.

Target IP/FQDN Enter the IP address or Fully Qualified

Domain Name (FQDN) that you want to ping. This can be either a local (LAN) or Internet (WAN) IP address.

Ping Size Enter the packet size you want to use. The

default is 32 bytes.

Backup Configuration

Backup To save the Gateway’s settings in a configuration

file, click this button and follow the on-screen instructions.

NOTE: The voice settings will not be saved in

the configuration file.

Restore Configuration

To use this option, you must have previously backed up its configuration settings.

Please select a file to restore Click Browse and select

the Gateway’s configuration file.

Restore To restore the Gateway’s configuration settings,

click this button and follow the on-screen instructions.

Administration > Factory Defaults

The Factory Defaults screen allows you to restore the Gateway’s configuration to its factory default settings, except for the voice settings. (An alternative method is to press and hold the Reset button on the Gateway’s back panel for approximately ten seconds.)

Number of Pings Enter how many times you want to

ping. The default is 3.

Ping Timeout Enter the number of milliseconds before the

ping test will time out. The default is 5000 milliseconds.

Ping Result The results of the ping test are displayed.

To run the test, click Start Test. Click Refresh to update the on-screen information.

Administration > Backup

The Backup screen allows you to back up or restore the Gateway’s settings using a configuration file.

Wireless-G ADSL2+ Gateway with VoIP

Administration > Factory Defaults

Page 39

Chapter 3

Advanced Configuration

NOTE: Restoring factory defaults deletes custom

settings except for the voice settings. Note your custom settings before clicking the Restore Factory Defaults button.

Factory Defaults

Restore Factory Defaults To reset settings to the

default values, click this button and follow the on-screen instructions. Any custom Gateway settings you have saved (except for the voice settings) will be lost when the default settings are restored.

Administration > Upgrade

The Upgrade screen allows you to upgrade the Gateway’s firmware. Do not upgrade the firmware unless you are experiencing problems with the Gateway or the new firmware has a feature you want to use.

NOTE: In rare cases (such as a power failure),

the firmware upgrade may fail. If that happens, the Gateway will enter recovery mode and automatically download firmware from your service provider’s provisioning server.

Administration > Reboot

The Reboot screen allows you to restart the Gateway through the web-based utility.

Administration > Reboot

Administration > Upgrade

NOTE: The Gateway may lose the settings

you have customized. Before you upgrade its firmware, write down all of your custom settings. After you upgrade its firmware, you will have to re-enter all of your configuration settings.

Firmware Upgrade

Before upgrading the firmware, download the Gateway’s firmware upgrade file from the Linksys website, www.linksys.com/international. Then extract the file.

Please Select a File to Upgrade Click Browse and select

the extracted firmware upgrade file.

Start to Upgrade After you have selected the

appropriate file, click this button, and follow the on-screen instructions.

Reboot

Click Reboot Box to restart the Gateway. The restart will terminate the Internet connection.

Administration > Logout

The Logout screen allows you to properly exit the web-based utility.

Administration > Logout

Logout

Click Logout to exit the web-based utility.

Wireless-G ADSL2+ Gateway with VoIP

Status > Internet

The Internet screen displays information about the Gateway and its current settings.

Page 40

Chapter 3

Advanced Configuration

Status > Local Network

Status > Internet

Gateway Information

Manufacturer OUI The manufacturer ID number is

displayed.

Serial Number The serial number of the Gateway is

displayed.

Hardware Version The version number of the Gateway’s

hardware is displayed.

Software Version The version number of the Gateway’s

software is displayed.

System Uptime The length of time the Gateway has

been active is displayed.

Local Time The date and time of the Gateway are

displayed.

Internet Connection

This section shows the current information for enabled connections. The table lists the following information about each connection: Interface, MAC/IP/Subnet, Gateway, DNS, and Status.

For DHCP connections, you can manually renew or release them. For PPP-type connections, you can manually connect or disconnect them.

Click Refresh to update the on-screen information.

Status > Local Network

The Local Network screen displays information about the local network.

Local Network

IP Address The Gateway’s IP address, as it appears on

your local network, is displayed.

Subnet Mask The Subnet Mask of the Gateway is

displayed.

DHCP Server The status of the Gateway’s DHCP server

function is displayed.

Starting IP Address For the range of IP addresses used

by devices on your local network, the starting IP address is displayed.

Ending IP Address For the range of IP addresses used

by devices on your local network, the ending IP address is displayed.

DHCP Lease Time The length of time for the DHCP lease

setting is displayed.

DHCP Client Table

The table displays DHCP, static, and dynamic (found by ARP) types of clients. It describes the devices that have been assigned IP addresses by the Gateway. For each device, the table lists the following information: Interface, MAC Address, IP Address, Host Name, and Lease Remaining (how much time is left for the current IP address).

IGMP Group Table

The table describes the IGMP configuration of the Gateway (if configured).

Click Refresh to update the on-screen information.

Status > Wireless

Wireless-G ADSL2+ Gateway with VoIP

The Wireless screen displays information about your wireless network(s).

Page 41

Chapter 3

Advanced Configuration

Downstream Rate The download speed of traffic from

the Internet to the Gateway is displayed.

Upstream Rate The upload speed of traffic from the

Gateway to the Internet is displayed. For ADSL connection, the Upstream Rate is typically 25% of the Downstream Rate.

NOTE: The Downstream and Upstream Rates are

affected by distance from and configuration of the DSL central office.

Status > Wireless

Wireless Network

For each wireless network, the following is displayed:

SSID The name of the wireless network is displayed.

MAC Address The MAC address of the Gateway’s local,

wireless interface is displayed.

Security The wireless security method is displayed (if

used).

SSID Broadcast The SSID broadcast setting is displayed.

Click Refresh to update the on-screen information.

Status > DSL Connection

The DSL Connection screen displays information about your DSL connection.

Downstream Noise Margin For downstream noise, the

number of decibels (dB) is displayed.

Upstream Noise Margin For upstream noise, the number

of dB is displayed.

Downstream Attenuation For downstream traffic, the

amount of signal loss is displayed.

Upstream Attenuation For upstream traffic, the mount

of signal loss is displayed.

Downstream Power For downstream power, the number

of decibels (referencing a millivolt) is displayed.

Upstream Power For upstream power, the number of

decibels (referencing a millivolt) is displayed.

Total Bytes Sent The number of bytes sent is displayed.

Total Bytes Received The number of bytes received is

displayed.

PVC Connection

For each PVC connection, the table lists the following information: Index, Status, Link Type, PVC, Encapsulation, QoS, PCR Rate, and SCR Rate.

Status > DSL Connection

DSL Connection

Modulation Type The DSL modulation mode of the

Gateway is displayed.

Status The status of the DSL connection is displayed.

Provider The name of the service provider is displayed.

Wireless-G ADSL2+ Gateway with VoIP

Click Refresh to update the on-screen information.

Status > Bridges

The Bridges screen displays information about the PVC/VLAN and default LAN bridges of the Gateway

Page 42

Chapter 3

Status > Bridges

Bridges

The total number of bridges and their descriptions are displayed.

Advanced Configuration

Port (Name/Type) The port name or type is displayed.

Learned Host (MAC/IP/Time to Expire) The MAC address,

IP address, or Time to Expire duration is displayed.

IGMP (Group Address/Time to Expire) The IGMP Group

Information of this port is displayed.

Click Refresh to update the on-screen information.

Wireless-G ADSL2+ Gateway with VoIP

Page 43

Appendix A

Troubleshooting

Appendix A: Troubleshooting

Your computer cannot connect to the Internet.

Follow the instructions until your computer can connect to the Internet:

Make sure that the Gateway is powered on. The Power • LED should be green and not flashing.

If the Power LED is flashing, then power off all of • your network devices, including the Gateway and computers. Then power on each device in the following order:

Gateway1.

Computer2.

Check the LEDs on the front panel of the Gateway. • Make sure the Power, DSL, and at least one of the numbered LEDs are lit. If they are not, then check the cable connections. The computer should be connected to one of the ports numbered 1-4 on the Gateway, and the Line port of the Gateway must be connected to the ADSL line.

You need to modify the advanced settings on the Gateway.

Open the web browser (for example, Internet Explorer or Firefox), and enter the Gateway’s IP address in the address field (the default IP address is 192.168.1.1). When prompted, complete the User name and Password fields (the default user name and password is admin). Click the appropriate tab to change the settings.

WEB: If your questions are not addressed

here, refer to the Linksys website,

www.linksys.com/international

When you double-click the web browser, you are prompted for a username and password. If you want to get rid of the prompt, follow these instructions.

Launch the web browser and perform the following steps (these steps are specific to Internet Explorer but are similar for other browsers):

Select 1. Tools > Internet Options.

Click the 2. Connections tab.

Select 3. Never dial a connection.

Click 4. OK.

The computer cannot connect wirelessly to the network.

Make sure the wireless network name or SSID is the same on both the computer and the Gateway. If you have enabled wireless security, then make sure the same security method and key are used by both the computer and the Gateway.

Wireless-G ADSL2+ Gateway with VoIP

Page 44

Appendix B

Appendix B: Specifications

Model WAG310G

Interfaces

WAN ADSL [ITU 992.1]; ADSL2 [ITU 992.3]; ADSL2+ [ITU 992.5] ANSI T1.413 Issue 2 1 RJ-11 Port 1 Ethernet WAN Interface RJ-45 Port (WAN/LAN congured)

LAN Maximum of 5 Ports (RJ-45) Ethernet 10/100 BaseT with Auto-Crossover (4 xed+ 1 congurable)

USB 1 USB 2.0 (host) Port Phone 2 FXS Ports (RJ-11);

1 FXO Port (RJ-11) Wi-Fi IEEE 802.11b/g

802.1x Authentication External RADIUS Authentication WPA2 and WPA Access WEP, AES & TKIP Encryption WPA/WEP Mixed Mode Wi-Fi Multimedia Support (WMM) Multiple SSIDs MAC Address Filtering Integrated WPS (Push button & PIN entry) Regional Channel Setting

LEDs Power, Ethernet, Wireless, USB, Phone(s), Line, DSL, Internet

Buttons On/O, Reset, WPS Mounting Desktop and Wall Mount Antenna One Omni Directional External

Antenna

Specifications

Environmental

Dimensions 220 x 42 x 175 mm (8.66" x 1.65" x 6.89")

Weight 400 g (14.11 oz) Power 110-240VAC 50/60 Hz Switching

Power Supply; 12VDC, 2A Output Certication FCC Part 68, Part 15, Class B, UL1950,

CSA, European EMC & Immunity, CE Mark, Industry-Canada

Operating Temp. 0 to 40°C (32 to 104°F) Storage Temp. 0 to 70°C (32 to 158°F) Humidity 20 to 80% Noncondensing

Specications are subject to change without notice.

Wireless-G ADSL2+ Gateway with VoIP

Page 45

Appendix C

Regulatory Information

Appendix C: Regulatory Information

United States of America

The following information applies if you use the product within the United States of America.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna •

Increase the separation between the equipment or • devices

Connect the equipment to an outlet other than the • receiver’s

Consult a dealer or an experienced radio/TV technician • for assistance

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. IEEE

802.11b or 802.11g operation of this product in the USA is firmware-limited to channels 1 through 11.

FCC Part 68 Statement

This equipment complies with Part 68 of the FCC Rules. A label is attached to the equipment that contains, among other information, its FCC registration number and ringer equivalence number. If requested, this information must be provided to the telephone company.

This equipment uses the following USOC Jack: RJ-11.

An FCC compliant telephone cord and modular plug is provided with this equipment. This equipment is designed to be connected to the telephone network or premises wiring using a compatible modular jack, which is FCC Part 68 compliant. Connection to the telephone network should be made by using the standard modular telephone jack.

The REN is useful to determine the quantity of devices that may be connected to the telephone line and still have all of those devices ring when your telephone number is called. In most, but not all areas, the sum of RENs should not exceed 5. To be certain of the number of devices that may be connected to the line, as determined by the total RENs, contact the telephone company to determine the maximum REN for the calling area.

If this equipment causes harm to the telephone network, the telephone company may discontinue your service temporarily. If advance notice is not practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make the necessary modifications in order to maintain uninterrupted service.

In the event this equipment should fail to operate properly, disconnect the unit from the telephone line. Try using another FCC approved device in the same telephone jack. If the trouble persists, call the telephone company repair service bureau. If the trouble does not persist and appears to be with this unit, disconnect the unit from the telephone line and discontinue use of the unit until it is repaired. Please note that the telephone company may ask that you disconnect the equipment from the telephone network until the problem has been corrected or until you are sure that the equipment is not malfunctioning. The user must use the accessories and cables supplied by the manufacturer to get optimum performance from the product.

No repairs may be done by the customer. If trouble is experienced with this equipment, please contact your authorized support provider for repair and warranty information. If the trouble is causing harm to the telephone network, the telephone company may request

Wireless-G ADSL2+ Gateway with VoIP

Page 46

Appendix C

Regulatory Information

you remove the equipment from the network until the problem is resolved. This equipment cannot be used on telephone company provided coin service. Connection to Party Line Service is subject to state tariffs.

Safety Notices

Caution: To reduce the risk of fire, use only No.26 AWG • or larger telecommunication line cord.

Do not use this product near water, for example, in a • wet basement or near a swimming pool.

Avoid using this product during an electrical storm. • There may be a remote risk of electric shock from lightning.

WARNING: This equipment will be inoperable

when main power fails.

WARNING: Many Internet phone service

providers do not support calls to emergency service numbers (000 in Australia or 111 in New Zealand). An alternative phone should be used to make emergency calls.

WARNING: To ensure compliance with exposure

limits to radiofrequency fields, the antenna of the WAG310G should be no closer than 20 cm from the body during use.

Canada

The following information applies if you use the product within Canada.

Industry Canada Statement

This device complies with Industry Canada ICES-003 and RSS210 rules.

Operation is subject to the following two conditions:

This device may not cause interference and1. This device must accept any interference, including 2.

interference that may cause undesired operation of the device. This device has been designed to operate with an antenna having a maximum gain of 2dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms.

To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the EIRP is not more than required for successful communication.

Industry Canada Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Avis d’Industrie Canada

Cet appareil est conforme aux normes NMB003 et RSS210 d’Industrie Canada.

L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes :

il ne doit pas produire de brouillage et 1. il doit accepter tout brouillage radioélectrique reçu, 2.

même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. Le dispositif a été conçu pour fonctionner avec une antenne ayant un gain maximum de 2 dBi. Les règlements d’Industrie Canada interdisent strictement l’utilisation d’antennes dont le gain est supérieur à cette limite. L’impédance requise de l’antenne est de 50 ohms. Afin de réduire le risque d’interférence aux autres utilisateurs, le type d’antenne et son gain doivent être choisis de façon à ce que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne soit pas supérieure au niveau requis pour obtenir une communication satisfaisante.

Avis d’Industrie Canada concernant l’exposition aux radiofréquences :

Ce matériel est conforme aux limites établies par IC en matière d’exposition aux radiofréquences dans un environnement non contrôlé. Ce matériel doit être installé et utilisé à une distance d’au moins 20 cm entre l’antenne et le corps de l’utilisateur.

L’émetteur ne doit pas être placé près d’une autre antenne ou d’un autre émetteur, ou fonctionner avec une autre antenne ou un autre émetteur.

Wireless Disclaimer

The maximum performance for wireless is derived from IEEE Standard 802.11 specifications. Actual performance can vary, including lower wireless network capacity, data throughput rate, range and coverage. Performance depends on many factors, conditions and variables, including distance from the access point, volume of network traffic, building materials and construction, operating system used, mix of wireless products used, interference and other adverse conditions.

Wireless-G ADSL2+ Gateway with VoIP

Page 47

Appendix C

Regulatory Information

Avis de non-responsabilité concernant les appareils sans fil

Les performances maximales pour les réseaux sans fil sont tirées des spécifications de la norme IEEE 802.11. Les performances réelles peuvent varier, notamment en fonction de la capacité du réseau sans fil, du débit de la transmission de données, de la portée et de la couverture. Les performances dépendent de facteurs, conditions et variables multiples, en particulier de la distance par rapport au point d’accès, du volume du trafic réseau, des matériaux utilisés dans le bâtiment et du type de construction, du système d’exploitation et de la combinaison de produits sans fil utilisés, des interférences et de toute autre condition défavorable.

New Zealand

The following information applies if you use the product within New Zealand.

Telepermit Statement

The cabling between the phone port and the phone shall not exceed 100 metres.

European Union

Deutsch [German]:

Eesti [Estonian]:

English:

Español [Spanish]:

Ελληνική [Greek]:

Français [French]:

Íslenska [Icelandic]:

Dieses Gerät entspricht den grundlegenden Anforderungen und den weiteren entsprechenden Vorgaben der Richtlinie 1999/5/EU.

See seade vastab direktiivi 1999/5/EÜ olulistele nõuetele ja teistele asjakohastele sätetele.

This equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

Este equipo cumple con los requisitos esenciales asi como con otras disposiciones de la Directiva 1999/5/CE.

Αυτός ο εξοπλισµός είναι σε συµµόρφωση µε τις ουσιώδεις απαιτήσεις και άλλες σχετικές διατάξεις της Οδηγίας 1999/5/EC.

Cet appareil est conforme aux exigences essentielles et aux autres dispositions pertinentes de la Directive 1999/5/EC.

Þetta tæki er samkvæmt grunnkröfum og öðrum viðeigandi ákvæðum Tilskipunar 1999/5/EC.

The following information applies if you use the product within the European Union.

Declaration of Conformity with Regard to EU Directive 1999/5/EC (R&TTE Directive)

Compliance Information for 2,4-GHz and 5-GHz Wireless Products Relevant to the EU and Other Countries Following the EU Directive 1999/5/EC (R&TTE Directive)

NOTE: The 5 GHz information does not apply to

Wireless-G (802.11g) only products.

Бъ л га р ск и [Bulgarian]

Česky [Czech]:

Dansk [Danish]:

Това оборудване отговаря на съществените изисквания и приложими клаузи на Директива 1999/5/ЕС.

Toto zařízení je v souladu se základními požadavky a ostatními odpovídajícími ustanoveními Směrnice 1999/5/EC.

Dette udstyr er i overensstemmelse med de væsentlige krav og andre relevante bestemmelser i Direktiv 1999/5/EF.

Italiano [Italian]:

Latviski [Latvian]:

Lietuvių [Lithuanian]:

Nederlands [Dutch]:

Malti [Maltese]:

Magyar [Hungarian]:

Norsk [Norwegian]:

Questo apparato é conforme ai requisiti essenziali ed agli altri principi sanciti dalla Direttiva 1999/5/CE.

Šī iekārta atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.

Šis įrenginys tenkina 1999/5/EB Direktyvos esminius reikalavimus ir kitas šios direktyvos nuostatas.

Dit apparaat voldoet aan de essentiele eisen en andere van toepassing zijnde bepalingen van de Richtlijn 1999/5/EC.

Dan l-apparat huwa konformi mal-ħtiġiet essenzjali u l-provedimenti l-oħra rilevanti tad-Direttiva 1999/5/EC.

Ez a készülék teljesíti az alapvető követelményeket és más 1999/5/EK irányelvben meghatározott vonatkozó rendelkezéseket.

Dette utstyret er i samsvar med de grunnleggende krav og andre relevante bestemmelser i EU-direktiv 1999/5/EF.

Wireless-G ADSL2+ Gateway with VoIP

Page 48

Appendix C

Regulatory Information

Polski [Polish]:

Português [Portuguese]:

Română [Romanian]

Slovensko [Slovenian]:

Slovensky [Slovak]:

Suomi [Finnish]:

Svenska [Swedish]:

Urządzenie jest zgodne z ogólnymi wymaganiami oraz szczególnymi warunkami określonymi Dyrektywą UE: 1999/5/EC.

Este equipamento está em conformidade com os requisitos essenciais e outras provisões relevantes da Directiva 1999/5/EC.

Acest echipament este in conformitate cu cerintele esentiale si cu alte prevederi relevante ale Directivei 1999/5/EC.

Ta naprava je skladna z bistvenimi zahtevami in ostalimi relevantnimi pogoji Direktive 1999/5/EC.

Toto zariadenie je v zhode so základnými požiadavkami a inými príslušnými nariadeniami direktív: 1999/5/EC.

Tämä laite täyttää direktiivin 1999/5/EY olennaiset vaatimukset ja on siinä asetettujen muiden laitetta koskevien määräysten mukainen.

Denna utrustning är i överensstämmelse med de väsentliga kraven och andra relevanta bestämmelser i Direktiv 1999/5/EC.

TPC: For operation in the 5 GHz band, the maximum power level is 3 dB or more below the applicable limit. As such, TPC is not required.

CE Marking

For the Linksys Wireless-N, -G, -B, and/or -A products, the following CE mark, notified body number (where applicable), and class 2 identifier are added to the equipment.

Check the CE label on the product to find out which notified body was involved during the assessment.

For all products, the Declaration of Conformity (DofC) is available through one or more of these options:

A pdf file is included on the product’s CD. •

A print copy is included with the product. •

A pdf file is available on the product’s webpage. • Visit www.linksys.com/international and select your country or region. Then select your product.

If you need any other technical documentation, see the “Technical Documents on www.linksys.com/international” section, as shown later in this appendix.

The following standards were applied during the assessment of the product against the requirements of the Directive 1999/5/EC:

Radio: EN 300 328 and/or EN 301 893 as applicable •

EMC: EN 301 489-1, EN 301 489-17 •

Safety: EN 60950 and either EN 50385 or EN 50371 •

Dynamic Frequency Selection (DFS) and Transmit Power Control (TPC) are required for operation in the 5 GHz band.

DFS: The equipment meets the DFS requirements as defined in ETSI EN 301 893. This feature is required by the regulations to avoid interference with Radio Location Services (radars).

National Restrictions

This product may be used in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below:

Ce produit peut être utilisé dans tous les pays de l’UE (et dans tous les pays ayant transposés la directive 1999/5/CE) sans aucune limitation, excepté pour les pays mentionnés cidessous:

Questo prodotto è utilizzabile in tutte i paesi EU (ed in tutti gli altri paesi che seguono le direttive EU 1999/5/EC) senza nessuna limitazione, eccetto per i paesi menzionati di seguito:

Das Produkt kann in allen EU Staaten ohne Einschränkungen eingesetzt werden (sowie in anderen Staaten die der EU Direktive 1999/5/CE folgen) mit Außnahme der folgenden aufgeführten Staaten:

In the majority of the EU and other European countries, the 2,4- and 5-GHz bands have been made available for the use of wireless local area networks (LANs). The table labeled “Overview of Regulatory Requirements for Wireless LANs” provides an overview of the regulatory requirements applicable for the 2,4- and 5-GHz bands.

Later in this document you will find an overview of countries in which additional restrictions or requirements or both are applicable.

Wireless-G ADSL2+ Gateway with VoIP

Page 49

Appendix C

Regulatory Information

The requirements for any country may evolve. Linksys recommends that you check with the local authorities for the latest status of their national regulations for both the 2,4- and 5-GHz wireless LANs.

Overview of Regulatory Requirements for Wireless LANs

Frequency

Band (MHz)

2400-2483.5 100 X

5150-5350

5470-5725

Dynamic Frequency Selection and Transmit Power Control are † required in the frequency ranges of 5250-5350 MHz and 5470-5725 MHz.

Max Power Level

†

Indoor

(EIRP) (mW)

200 X

1000 X

ONLY

Indoor &

Outdoor

The following countries have restrictions and/or requirements in addition to those given in the table labeled “Overview of Regulatory Requirements for Wireless LANs”:

Denmark

In Denmark, the band 5150 - 5350 MHz is also allowed for outdoor usage.

I Danmark må frekvensbåndet 5150 - 5350 også anvendes udendørs.

France

For 2,4 GHz, the product should not be used outdoors in the band 2454 - 2483,5 MHz. There are no restrictions when used in other parts of the 2,4 GHz band when used indoors. Check http://www.arcep.fr/ for more details.

Pour la bande 2,4 GHz, l’ équipement ne doit pas être utilisé en extérieur dans la bande 2454 - 2483,5 MHz. Il n’y a pas de restrictions pour des utilisations en intérieur dans d’autres parties de la bande 2,4GHz. Consultez http://www.arcep.fr/ pour de plus amples détails.

Applicable Power Levels in France

Location

Indoor

(No restrictions)

Outdoor

Frequency

Range (MHz)

2400-2483.5 100 mW (20 dBm)

2400-2454

2454-2483.5

Power (EIRP)

100 mW (20 dBm)

10 mW (10 dBm)

Italy

This product meets the National Radio Interface and the requirements specified in the National Frequency Allocation Table for Italy. Unless this 2,4-GHz wireless LAN

product is operating within the boundaries of the owner’s property, its use requires a “general authorization”. Please check http://www.comunicazioni.it/it/ for more details.

Questo prodotto è conforme alla specifiche di Interfaccia Radio Nazionali e rispetta il Piano Nazionale di ripartizione delle frequenze in Italia. Se non viene installato all’interno del proprio fondo, l’utilizzo di prodotti Wireless LAN a 2,4 GHz richiede una “Autorizzazione Generale”. Consultare http://www.comunicazioni.it/it/ per maggiori dettagli.

Latvia

The outdoor usage of the 2,4 GHz band requires an authorization from the Electronic Communications Office. Please check http://www.esd.lv for more details.

2,4 GHz frekveču joslas izmantošanai ārpus telpām nepieciešama atļauja no Elektronisko sakaru direkcijas. Vairāk informācijas: http://www.esd.lv.

Notes:

Although Norway, Switzerland and Liechtenstein are 1. not EU member states, the EU Directive 1999/5/EC has also been implemented in those countries.

The regulatory limits for maximum output power are 2. specified in EIRP. The EIRP level of a device can be calculated by adding the gain of the antenna used (specified in dBi) to the output power available at the connector (specified in dBm).

Product Usage Restrictions

This product is designed for indoor usage only. Outdoor usage is not recommended, unless otherwise noted.

2,4 GHz Restrictions

This product is designed for use with the standard, integral or dedicated (external) antenna(s) that is/are shipped together with the equipment. However, some applications may require the antenna(s), if removable, to be separated from the product and installed remotely from the device by using extension cables. For these applications, Linksys offers an R-SMA extension cable (AC9SMA) and an R-TNC extension cable (AC9TNC). Both of these cables are 9 meters long and have a cable loss (attenuation) of 5 dB. To compensate for the attenuation, Linksys also offers higher gain antennas, the HGA7S (with R-SMA connector) and HGA7T (with R-TNC connector). These antennas have a gain of 7 dBi and may only be used with either the R-SMA or R-TNC extension cable.

Combinations of extension cables and antennas resulting in a radiated power level exceeding 100 mW EIRP are illegal.

Wireless-G ADSL2+ Gateway with VoIP

Page 50

Appendix C

Regulatory Information

Third-Party Software or Firmware

The use of software or firmware not supported/provided by Linksys may result that the equipment is no longer compliant with the regulatory requirements.

Technical Documents on www.linksys.com/international

Follow these steps to access technical documents:

Enter http://www.linksys.com/international in your 1. web browser.

Select the country or region in which you live.2. Click the 3. Products tab. Select the appropriate product category.4. Select the product sub-category, if necessary.5. Select the product.6. Select the type of documentation you want from the 7.

More Information section. The document will open in PDF format if you have Adobe Acrobat installed on your computer.

NOTE: If you have questions regarding

the compliance of this product or you cannot find the information you need, please contact your local sales office or visit

www.linksys.com/international

User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic Equipment (WEEE)

This document contains important information for users with regards to the proper disposal and recycling of Linksys products. Consumers are required to comply with this notice for all electronic products bearing the following symbol:

English - Environmental Information for Customers in the European Union

European Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. For more detailed information about the disposal of your old equipment, please contact your local authorities, waste disposal service, or the shop where you purchased the product.

Wireless-G ADSL2+ Gateway with VoIP

Български (Bulgarian) - Информация относно опазването на околната среда за потребители в Европейския съюз

Европейска директива 2002/96/EC изисква уредите, носещи този символ върху изделието и/или опаковката му, да не се изхвърля т с несортирани битови отпадъци. Символът обозначава, че изделието трябва да се изхвърля отделно от сметосъбирането на обикновените битови отпадъци. Ваша е отговорността този и другите електрически и електронни уреди да се изхвърлят в предварително определени от държавните или общински органи специализирани пунктове за събиране. Правилното изхвърляне и рециклиране ще спомогнат да се предотвратят евентуални вредни за околната среда и здравето на населението последствия. За по-подробна информация относно изхвърлянето на вашите стари уреди се обърнете към местните власти, службите за сметосъбиране или магазина, от който сте закупили уреда.

Page 51

Appendix C

Regulatory Information

Ceština (Czech) - Informace o ochraně životního prostředí pro zákazníky v zemích Evropské unie

Evropská směrnice 2002/96/ES zakazuje, aby zařízení označené tímto symbolem na produktu anebo na obalu bylo likvidováno s netříděným komunálním odpadem. Tento symbol udává, že daný produkt musí být likvidován odděleně od běžného komunálního odpadu. Odpovídáte za likvidaci tohoto produktu a dalších elektrických a elektronických zařízení prostřednictvím určených sběrných míst stanovených vládou nebo místními úřady. Správná likvidace a recyklace pomáhá předcházet potenciálním negativním dopadům na životní prostředí a lidské zdraví. Podrobnější informace o likvidaci starého vybavení si laskavě vyžádejte od místních úřadů, podniku zabývajícího se likvidací komunálních odpadů nebo obchodu, kde jste produkt zakoupili.

Dansk (Danish) - Miljøinformation for kunder i EU

EU-direktiv 2002/96/EF kræver, at udstyr der bærer dette symbol

på produktet og/eller emballagen ikke må bortskaffes som usorteret kommunalt affald. Symbolet betyder, at dette produkt skal bortskaffes adskilt fra det almindelige husholdningsaffald. Det er dit ansvar at bortskaffe dette og andet elektrisk og elektronisk udstyr via bestemte indsamlingssteder udpeget af staten eller de lokale myndigheder. Korrekt bortskaffelse og genvinding vil hjælpe med til at undgå mulige skader for miljøet og menneskers sundhed. Kontakt venligst de lokale myndigheder, renovationstjenesten eller den butik, hvor du har købt produktet, angående mere detaljeret information om bortskaffelse af dit gamle udstyr.

Deutsch (German) - Umweltinformation für Kunden innerhalb der Europäischen Union

Die Europäische Richtlinie 2002/96/EC verlangt, dass technische Ausrüstung, die direkt am Gerät und/oder an der Verpackung mit diesem Symbol versehen ist , nicht zusammen mit unsortiertem Gemeindeabfall entsorgt werden darf. Das Symbol weist darauf hin, dass das Produkt von regulärem Haushaltmüll getrennt entsorgt werden sollte. Es liegt in Ihrer Verantwortung, dieses Gerät und andere elektrische und elektronische Geräte über die dafür zuständigen und von der Regierung oder örtlichen Behörden dazu bestimmten Sammelstellen zu entsorgen. Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei, potentielle negative Folgen für Umwelt und die menschliche Gesundheit zu vermeiden. Wenn Sie weitere Informationen zur Entsorgung Ihrer Altgeräte benötigen, wenden Sie sich bitte an die örtlichen Behörden oder städtischen Entsorgungsdienste oder an den Händler, bei dem Sie das Produkt erworben haben.

Eesti (Estonian) - Keskkonnaalane informatsioon Euroopa Liidus asuvatele klientidele

Euroopa Liidu direktiivi 2002/96/EÜ nõuete kohaselt on seadmeid, millel on tootel või pakendil käesolev sümbol , keelatud kõrvaldada koos sorteerimata olmejäätmetega. See sümbol näitab, et toode tuleks kõrvaldada eraldi tavalistest olmejäätmevoogudest. Olete kohustatud kõrvaldama käesoleva ja ka muud elektri- ja elektroonikaseadmed riigi või kohalike ametiasutuste poolt ette nähtud kogumispunktide kaudu. Seadmete korrektne kõrvaldamine ja ringlussevõtt aitab vältida võimalikke negatiivseid tagajärgi keskkonnale ning inimeste tervisele. Vanade seadmete kõrvaldamise kohta täpsema informatsiooni saamiseks võtke palun ühendust kohalike ametiasutustega, jäätmekäitlusfirmaga või kauplusega, kust te toote ostsite.

Español (Spanish) - Información medioambiental para clientes de la Unión Europea

La Directiva 2002/96/CE de la UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación. Es responsabilidad suya desechar este y cualesquiera otros aparatos eléctricos y electrónicos a través de los puntos de recogida que ponen a su disposición el gobierno y las autoridades locales. Al desechar y reciclar correctamente estos aparatos estará contribuyendo a evitar posibles consecuencias negativas para el medio ambiente y la salud de las personas. Si desea obtener información más detallada sobre la eliminación segura de su aparato usado, consulte a las autoridades locales, al servicio de recogida y eliminación de residuos de su zona o pregunte en la tienda donde adquirió el producto.

ξλληνικά (Greek) - Στοιχεία περιβαλλοντικής προστασίας για πελάτες εντός της Ευρωπαϊκής Ένωσης

Η Κοινοτική Οδηγία 2002/96/EC απαιτεί ότι ο εξοπλισμός ο οποίος φέρει αυτό το σύμβολο στο προϊόν και/ή στη συσκευασία του δεν πρέπει να απορρίπτεται μαζί με τα μικτά κοινοτικά απορρίμματα. Το σύμβολο υποδεικνύει ότι αυτό το προϊόν θα πρέπει να απορρίπτεται ξεχωριστά από τα συνήθη οικιακά απορρίμματα. Είστε υπεύθυνος για την απόρριψη του παρόντος και άλλου ηλεκτρικού και ηλεκτρονικού εξοπλισμού μέσω των καθορισμένων εγκαταστάσεων συγκέντρωσης απορριμμάτων οι οποίες παρέχονται από το κράτος ή τις αρμόδιες τοπικές αρχές. Η σωστή απόρριψη και ανακύκλωση συμβάλλει στην πρόληψη πιθανών αρνητικών συνεπειών για το περιβάλλον και την υγεία. Για περισσότερες πληροφορίες σχετικά με την απόρριψη του παλιού σας εξοπλισμού, παρακαλώ επικοινωνήστε με τις τοπικές αρχές, τις υπηρεσίες απόρριψης ή το κατάστημα από το οποίο αγοράσατε το προϊόν.

Wireless-G ADSL2+ Gateway with VoIP

Page 52

Appendix C

Regulatory Information

Français (French) - Informations environnementales pour les clients de l’Union européenne

La directive européenne 2002/96/CE exige que l’équipement sur lequel est apposé ce symbole sur le produit et/ou son emballage ne soit pas jeté avec les autres ordures ménagères. Ce symbole indique que le produit doit être éliminé dans un circuit distinct de celui pour les déchets des ménages. Il est de votre responsabilité de jeter ce matériel ainsi que tout autre matériel électrique ou électronique par les moyens de collecte indiqués par le gouvernement et les pouvoirs publics des collectivités territoriales. L’élimination et le recyclage en bonne et due forme ont pour but de lutter contre l’impact néfaste potentiel de ce type de produits sur l’environnement et la santé publique. Pour plus d’informations sur le mode d’élimination de votre ancien équipement, veuillez prendre contact avec les pouvoirs publics locaux, le service de traitement des déchets, ou l’endroit où vous avez acheté le produit.

Italiano (Italian) - Informazioni relative all’ambiente per i clienti residenti nell’Unione Europea

La direttiva europea 2002/96/EC richiede che le apparecchiature contrassegnate con questo simbolo sul prodotto e/o sull’imballaggio non siano smaltite insieme ai rifiuti urbani non differenziati. Il simbolo indica che questo prodotto non deve essere smaltito insieme ai normali rifiuti domestici. È responsabilità del proprietario smaltire sia questi prodotti sia le altre apparecchiature elettriche ed elettroniche mediante le specifiche strutture di raccolta indicate dal governo o dagli enti pubblici locali. Il corretto smaltimento ed il riciclaggio aiuteranno a prevenire conseguenze potenzialmente negative per l’ambiente e per la salute dell’essere umano. Per ricevere informazioni più dettagliate circa lo smaltimento delle vecchie apparecchiature in Vostro possesso, Vi invitiamo a contattare gli enti pubblici di competenza, il servizio di smaltimento rifiuti o il negozio nel quale avete acquistato il prodotto.

Latviešu valoda (Latvian) - Ekoloģiska informācija klientiem Eiropas Savienības jurisdikcijā

Direktīvā 2002/96/EK ir prasība, ka aprīkojumu, kam pievienota zīme uz paša izstrādājuma vai uz tā iesaiņojuma, nedrīkst izmest nešķirotā veidā kopā ar komunālajiem atkritumiem (tiem, ko rada vietēji iedzīvotāji un uzņēmumi). Šī zīme nozīmē to, ka šī ierīce ir jāizmet atkritumos tā, lai tā nenonāktu kopā ar parastiem mājsaimniecības atkritumiem. Jūsu pienākums ir šo un citas elektriskas un elektroniskas ierīces izmest atkritumos, izmantojot īpašus atkritumu savākšanas veidus un līdzekļus, ko nodrošina valsts un pašvaldību iestādes. Ja izmešana atkritumos un pārstrāde tiek veikta pareizi, tad mazinās iespējamais kaitējums dabai un cilvēku veselībai. Sīkākas ziņas par novecojuša aprīkojuma izmešanu atkritumos jūs varat saņemt vietējā pašvaldībā, atkritumu savākšanas dienestā, kā arī veikalā, kur iegādājāties šo izstrādājumu.

Lietuvškai (Lithuanian) - Aplinkosaugos informacija, skirta Europos Sąjungos vartotojams

Europos direktyva 2002/96/EC numato, kad įrangos, kuri ir kurios pakuotė yra pažymėta šiuo simboliu (įveskite simbolį), negalima šalinti kartu su nerūšiuotomis komunalinėmis atliekomis. Šis simbolis rodo, kad gaminį reikia šalinti atskirai nuo bendro buitinių atliekų srauto. Jūs privalote užtikrinti, kad ši ir kita elektros ar elektroninė įranga būtų šalinama per tam tikras nacionalinės ar vietinės valdžios nustatytas atliekų rinkimo sistemas. Tinkamai šalinant ir perdirbant atliekas, bus išvengta galimos žalos aplinkai ir žmonių sveikatai. Daugiau informacijos apie jūsų senos įrangos šalinimą gali pateikti vietinės valdžios institucijos, atliekų šalinimo tarnybos arba parduotuvės, kuriose įsigijote tą gaminį.

Malti (Maltese) - Informazzjoni Ambjentali għal Klijenti fl-Unjoni Ewropea

Id-Direttiva Ewropea 2002/96/KE titlob li t-tagħmir li jkun fih issimbolu fuq il-prodott u/jew fuq l-ippakkjar ma jistax jintrema ma’ skart muniċipali li ma ġiex isseparat. Is-simbolu jindika li dan il-prodott għandu jintrema separatament minn ma’ liskart domestiku regolari. Hija responsabbiltà tiegħek li tarmi dan it-tagħmir u kull tagħmir ieħor ta’ l-elettriku u elettroniku permezz ta’ faċilitajiet ta’ ġbir appuntati apposta mill-gvern jew mill-awtoritajiet lokali. Ir-rimi b’mod korrett u r-riċiklaġġ jgħin jipprevjeni konsegwenzi negattivi potenzjali għall-ambjent u għas-saħħa tal-bniedem. Għal aktar informazzjoni dettaljata dwar ir-rimi tat-tagħmir antik tiegħek, jekk jogħġbok ikkuntattja lill-awtoritajiet lokali tiegħek, is-servizzi għar-rimi ta’ l-iskart, jew il-ħanut minn fejn xtrajt il-prodott.

Magyar (Hungarian) - Környezetvédelmi információ az európai uniós vásárlók számára

A 2002/96/EC számú európai uniós irányelv megkívánja, hogy azokat a termékeket, amelyeken, és/vagy amelyek csomagolásán az alábbi címke megjelenik, tilos a többi szelektálatlan lakossági hulladékkal együtt kidobni. A címke azt jelöli, hogy az adott termék kidobásakor a szokványos háztartási hulladékelszállítási rendszerektõl elkülönített eljárást kell alkalmazni. Az Ön felelõssége, hogy ezt, és más elektromos és elektronikus berendezéseit a kormányzati vagy a helyi hatóságok által kijelölt gyűjtõredszereken keresztül számolja fel. A megfelelõ hulladékfeldolgozás segít a környezetre és az emberi egészségre potenciálisan ártalmas negatív hatások megelõzésében. Ha elavult berendezéseinek felszámolásához további részletes információra van szüksége, kérjük, lépjen kapcsolatba a helyi hatóságokkal, a hulladékfeldolgozási szolgálattal, vagy azzal üzlettel, ahol a terméket vásárolta.

Wireless-G ADSL2+ Gateway with VoIP

Page 53

Appendix C

Regulatory Information

Nederlands (Dutch) - Milieu-informatie voor klanten in de Europese Unie

De Europese Richtlijn 2002/96/EC schrijft voor dat apparatuur die is voorzien van dit symbool op het product of de verpakking, niet mag worden ingezameld met niet-gescheiden huishoudelijk afval. Dit symbool geeft aan dat het product apart moet worden ingezameld. U bent zelf verantwoordelijk voor de vernietiging van deze en andere elektrische en elektronische apparatuur via de daarvoor door de landelijke of plaatselijke overheid aangewezen inzamelingskanalen. De juiste vernietiging en recycling van deze apparatuur voorkomt mogelijke negatieve gevolgen voor het milieu en de gezondheid. Voor meer informatie over het vernietigen van uw oude apparatuur neemt u contact op met de plaatselijke autoriteiten of afvalverwerkingsdienst, of met de winkel waar u het product hebt aangeschaft.

Norsk (Norwegian) - Miljøinformasjon for kunder i EU

EU-direktiv 2002/96/EF krever at utstyr med følgende symbol

avbildet på produktet og/eller pakningen, ikke må kastes sammen med usortert avfall. Symbolet indikerer at dette produktet skal håndteres atskilt fra ordinær avfallsinnsamling for husholdningsavfall. Det er ditt ansvar å kvitte deg med dette produktet og annet elektrisk og elektronisk avfall via egne innsamlingsordninger slik myndighetene eller kommunene bestemmer. Korrekt avfallshåndtering og gjenvinning vil være med på å forhindre mulige negative konsekvenser for miljø og helse. For nærmere informasjon om håndtering av det kasserte utstyret ditt, kan du ta kontakt med kommunen, en innsamlingsstasjon for avfall eller butikken der du kjøpte produktet.

Polski (Polish) - Informacja dla klientów w Unii Europejskiej o przepisach dotyczących ochrony środowiska

Dyrektywa Europejska 2002/96/EC wymaga, aby sprzęt oznaczony symbolem znajdującym się na produkcie i/lub jego opakowaniu nie był wyrzucany razem z innymi niesortowanymi odpadami komunalnymi. Symbol ten wskazuje, że produkt nie powinien być usuwany razem ze zwykłymi odpadami z gospodarstw domowych. Na Państwu spoczywa obowiązek wyrzucania tego i innych urządzeń elektrycznych oraz elektronicznych w punktach odbioru wyznaczonych przez władze krajowe lub lokalne. Pozbywanie się sprzętu we właściwy sposób i jego recykling pomogą zapobiec potencjalnie negatywnym konsekwencjom dla środowiska i zdrowia ludzkiego. W celu uzyskania szczegółowych informacji o usuwaniu starego sprzętu, prosimy zwrócić się do lokalnych władz, służb oczyszczania miasta lub sklepu, w którym produkt został nabyty.

Português (Portuguese) - Informação ambiental para clientes da União Europeia

A Directiva Europeia 2002/96/CE exige que o equipamento que exibe este símbolo no produto e/ou na sua embalagem não seja eliminado junto com os resíduos municipais não separados. O símbolo indica que este produto deve ser eliminado separadamente dos resíduos domésticos regulares. É da sua responsabilidade eliminar este e qualquer outro equipamento eléctrico e electrónico através das instalações de recolha designadas pelas autoridades governamentais ou locais. A eliminação e reciclagem correctas ajudarão a prevenir as consequências negativas para o ambiente e para a saúde humana. Para obter informações mais detalhadas sobre a forma de eliminar o seu equipamento antigo, contacte as autoridades locais, os serviços de eliminação de resíduos ou o estabelecimento comercial onde adquiriu o produto.

Română (Romanian) - Informaţii de mediu pentru clienţii din Uniunea Europeană

Directiva europeană 2002/96/CE impune ca echipamentele care prezintă acest simbol pe produs şi/sau pe ambalajul acestuia să nu fie casate împreună cu gunoiul menajer municipal. Simbolul indică faptul că acest produs trebuie să fie casat separat de gunoiul menajer obişnuit. Este responsabilitatea dvs. să casaţi acest produs şi alte echipamente electrice şi electronice prin intermediul unităţilor de colectare special desemnate de guvern sau de autorităţile locale. Casarea şi reciclarea corecte vor ajuta la prevenirea potenţialelor consecinţe negative asupra sănătăţii mediului şi a oamenilor. Pentru mai multe informaţii detaliate cu privire la casarea acestui echipament vechi, contactaţi autorităţile locale, serviciul de salubrizare sau magazinul de la care aţi achiziţionat produsul.

Slovenčina (Slovak) - Informácie o ochrane životného prostredia pre zákazníkov v Európskej únii

Podľa európskej smernice 2002/96/ES zariadenie s týmto symbolom na produkte a/alebo jeho balení nesmie byť likvidované spolu s netriedeným komunálnym odpadom. Symbol znamená, že produkt by sa mal likvidovať oddelene od bežného odpadu z domácností. Je vašou povinnosťou likvidovať toto i ostatné elektrické a elektronické zariadenia prostredníctvom špecializovaných zberných zariadení určených vládou alebo miestnymi orgánmi. Správna likvidácia a recyklácia pomôže zabrániť prípadným negatívnym dopadom na životné prostredie a zdravie ľudí. Ak máte záujem o podrobnejšie informácie o likvidácii starého zariadenia, obráťte sa, prosím, na miestne orgány, organizácie zaoberajúce sa likvidáciou odpadov alebo obchod, v ktorom ste si produkt zakúpili.

Wireless-G ADSL2+ Gateway with VoIP

Page 54

Appendix C

Slovenčina (Slovene) - Okoljske informacije za stranke v Evropski uniji

Evropska direktiva 2002/96/EC prepoveduje odlaganje opreme, označene s tem simbolom – na izdelku in/ali na embalaži – med običajne, nerazvrščene odpadke. Ta simbol opozarja, da je treba izdelek odvreči ločeno od preostalih gospodinjskih odpadkov. Vaša odgovornost je, da to in preostalo električno in elektronsko opremo odnesete na posebna zbirališča, ki jih določijo državne ustanove ali lokalna uprava. S pravilnim odlaganjem in recikliranjem boste preprečili morebitne škodljive vplive na okolje in zdravje ljudi. Če želite izvedeti več o odlaganju stare opreme, se obrnite na lokalno upravo, odpad ali trgovino, kjer ste izdelek kupili.

Suomi (Finnish) - Ympäristöä koskevia tietoja EUalueen asiakkaille

EU-direktiivi 2002/96/EY edellyttää, että jos laitteistossa on tämä symboli itse tuotteessa ja/tai sen pakkauksessa, laitteistoa ei saa hävittää lajittelemattoman yhdyskuntajätteen mukana. Symboli merkitsee sitä, että tämä tuote on hävitettävä erillään tavallisesta kotitalousjätteestä. Sinun vastuullasi on hävittää tämä elektroniikkatuote ja muut vastaavat elektroniikkatuotteet viemällä tuote tai tuotteet viranomaisten määräämään keräyspisteeseen. Laitteiston oikea hävittäminen estää mahdolliset kielteiset vaikutukset ympäristöön ja ihmisten terveyteen. Lisätietoja vanhan laitteiston oikeasta hävitystavasta saa paikallisilta viranomaisilta, jätteenhävityspalvelusta tai siitä myymälästä, josta ostit tuotteen.

Regulatory Information

Svenska (Swedish) - Miljöinformation för kunder i Europeiska unionen

Det europeiska direktivet 2002/96/EC kräver att utrustning med denna symbol på produkten och/eller förpackningen inte får kastas med osorterat kommunalt avfall. Symbolen visar att denna produkt bör kastas efter att den avskiljts från vanligt hushållsavfall. Det faller på ditt ansvar att kasta denna och annan elektrisk och elektronisk utrustning på fastställda insamlingsplatser utsedda av regeringen eller lokala myndigheter. Korrekt kassering och återvinning skyddar mot eventuella negativa konsekvenser för miljön och personhälsa. För mer detaljerad information om kassering av din gamla utrustning kontaktar du dina lokala myndigheter, avfallshanteringen eller butiken där du köpte produkten.

WEB: For additional information, please visit

www.linksys.com/international

Wireless-G ADSL2+ Gateway with VoIP

Page 55

Appendix D

Software License Agreement

Appendix D: Software License Agreement

Software in Linksys Products

This product from Cisco-Linksys LLC or from one of its affiliates Cisco Systems-Linksys (Asia) Pte Ltd. or CiscoLinksys K.K. (“Linksys”) contains software (including firmware) originating from Linksys and its suppliers and may also contain software from the open source community. Any software originating from Linksys and its suppliers is licensed under the Linksys Software License Agreement contained at Schedule 1 below. You may also be prompted to review and accept that Linksys Software License Agreement upon installation of the software

Any software from the open source community is licensed under the specific license terms applicable to that software made available by Linksys at www.linksys.com/gpl or as provided for in Schedules 2, 3 and 4 below.

Where such specific license terms entitle you to the source code of such software, that source code is upon request available at cost from Linksys for at least three years from the purchase date of this product and may also be available for download from www.linksys.com/gpl. For detailed license terms and additional information on open source software in Linksys products please look at the Linksys public web site at: www.linksys.com/gpl/ or Schedules 2, 3 or 4 below as applicable.

BY DOWNLOADING OR INSTALLING THE SOFTWARE, OR USING THE PRODUCT CONTAINING THE SOFTWARE, YOU ARE CONSENTING TO BE BOUND BY THE SOFTWARE LICENSE AGREEMENTS BELOW. IF YOU DO NOT AGREE TO ALL OF THESE TERMS, THEN YOU MAY NOT DOWNLOAD, INSTALL OR USE THE SOFTWARE. YOU MAY RETURN UNUSED SOFTWARE (OR, IF THE SOFTWARE IS SUPPLIED AS PART OF ANOTHER PRODUCT, THE UNUSED PRODUCT) FOR A FULL REFUND UP TO 30 DAYS AFTER ORIGINAL PURCHASE, SUBJECT TO THE RETURN PROCESS AND POLICIES OF THE PARTY FROM WHICH YOU PURCHASED SUCH PRODUCT OR SOFTWARE.

Software Licenses

The software Licenses applicable to software from Linksys are made available at the Linksys public web site at: www.linksys.com. For your convenience of reference, a copy of the Linksys Software License Agreement and the main open source code licenses used by Linksys in its products are contained in the Schedules below.

Schedule 1 - Linksys Software License Agreement

THIS LICENSE AGREEMENT IS BETWEEN YOU AND CISCO-LINKSYS LLC OR ONE OF ITS AFFILIATES CISCO SYSTEMS-LINKSYS (ASIA) PTE LTD. OR CISCO-LINKSYS K.K. (“LINKSYS”) LICENSING THE SOFTWARE INSTEAD OF CISCO-LINKSYS LLC. BY DOWNLOADING OR INSTALLING THE SOFTWARE, OR USING THE PRODUCT CONTAINING THE SOFTWARE, YOU ARE CONSENTING TO BE BOUND BY THIS AGREEMENT. IF YOU DO NOT AGREE TO ALL OF THESE TERMS, THEN YOU MAY NOT DOWNLOAD, INSTALL OR USE THE SOFTWARE. YOU MAY RETURN UNUSED SOFTWARE (OR, IF THE SOFTWARE IS SUPPLIED AS PART OF ANOTHER PRODUCT, THE UNUSED PRODUCT) FOR A FULL REFUND UP TO 30 DAYS AFTER ORIGINAL PURCHASE, SUBJECT TO THE RETURN PROCESS AND POLICIES OF THE PARTY FROM WHICH YOU PURCHASED SUCH PRODUCT OR SOFTWARE.

License. Subject to the terms and conditions of this Agreement, Linksys grants the original end user purchaser of the Linksys product containing the Software (“You”) a nonexclusive license to use the Software solely as embedded in or (where authorized in the applicable documentation) for communication with such product. This license may not be sublicensed, and is not transferable except to a person or entity to which you transfer ownership of the complete Linksys product containing the Software, provided you permanently transfer all rights under this Agreement and do not retain any full or partial copies of the Software, and the recipient agrees to the terms of this Agreement.

“Software” includes, and this Agreement will apply to (a) the software of Linksys or its suppliers provided in or with the applicable Linksys product, excluding technology from the open source community, and (b) any upgrades, updates, bug fixes or modified versions (“Upgrades”) or backup copies of the Software supplied to You by Linksys or an authorized reseller, provided you already hold a valid license to the original software and have paid any applicable fee for the Upgrade.

Protection of Information. The Software and documentation contain trade secrets and/or copyrighted materials of Linksys or its suppliers. You will not copy or modify the Software or decompile, decrypt, reverse engineer or disassemble the Software (except to the extent expressly permitted by law notwithstanding this provision), and You will not disclose or make available such trade secrets or copyrighted material in any form to any third party. Title to and ownership of the Software and documentation and any portion thereof, will remain solely with Linksys or its suppliers.

Collection and Processing of Information. You agree that Linksys and/or its affiliates may, from time to time, collect and process information about your Linksys product and/ or the Software and/or your use of either in order (i) to enable Linksys to offer you Upgrades; (ii) to ensure that

Wireless-G ADSL2+ Gateway with VoIP

Page 56

Appendix D

Software License Agreement

your Linksys product and/or the Software is being used in accordance with the terms of this Agreement; (iii) to provide improvements to the way Linksys delivers technology to you and to other Linksys customers; (iv) to enable Linksys to comply with the terms of any agreements it has with any third parties regarding your Linksys product and/or Software and/or (v) to enable Linksys to comply with all applicable laws and/or regulations, or the requirements of any regulatory authority or government agency. Linksys and/ or its affiliates may collect and process this information provided that it does not identify you personally. Your use of your Linksys product and/or the Software constitutes this consent by you to Linksys and/ or its affiliates’ collection and use of such information and, for EEA customers, to the transfer of such information to a location outside the EEA.

Software Upgrades etc. If the Software enables you to receive Upgrades, you may elect at any time to receive these Upgrades either automatically or manually. If you elect to receive Upgrades manually or you otherwise elect not to receive or be notified of any Upgrades, you may expose your Linksys product and/or the Software to serious security threats and/or some features within your Linksys product and/or Software may become inaccessible. There may be circumstances where we apply an Upgrade automatically in order to comply with changes in legislation, legal or regulatory requirements or as a result of requirements to comply with the terms of any agreements Linksys has with any third parties regarding your Linksys product and/or the Software. You will always be notified of any Upgrades being delivered to you. The terms of this license will apply to any such Upgrade unless the Upgrade in question is accompanied by a separate license, in which event the terms of that license will apply.

Open Source Software. The GPL or other open source code incorporated into the Software and the open source license for such source code are available for free download at http://www.linksys.com/gpl. If You would like a copy of the GPL or other open source code in this Software on a CD, Linksys will mail to You a CD with such code for $9.99 plus the cost of shipping, upon request.

Term and Termination. You may terminate this License at any time by destroying all copies of the Software and documentation. Your rights under this License will terminate immediately without notice from Linksys if You fail to comply with any provision of this Agreement.

Limited Warranty. The warranty terms and period specified in the applicable Linksys Product User Guide shall also apply to the Software.

Disclaimer of Liabilities. IN NO EVENT WILL LINKSYS OR ITS SUPPLIERS BE LIABLE FOR ANY LOST DATA, REVENUE OR PROFIT, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL, INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF CAUSE (INCLUDING NEGLIGENCE), ARISING OUT OF

Wireless-G ADSL2+ Gateway with VoIP

OR RELATED TO THE USE OF OR INABILITY TO USE THE SOFTWARE, EVEN IF LINKSYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT WILL LINKSYS’ LIABILITY EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT. The foregoing limitations will apply even if any warranty or remedy under this Agreement fails of its essential purpose. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to You.

Export. Software, including technical data, may be subject to U.S. export control laws and regulations and/or export or import regulations in other countries. You agree to comply strictly with all such laws and regulations.

U.S. Government Users. The Software and documentation qualify as “commercial items” as defined at 48 C.F.R. 2.101 and 48 C.F.R. 12.212. All Government users acquire the Software and documentation with only those rights herein that apply to non-governmental customers.

General Terms. This Agreement will be governed by and construed in accordance with the laws of the State of California, without reference to conflict of laws principles. The United Nations Convention on Contracts for the International Sale of Goods will not apply. If any portion of this Agreement is found to be void or unenforceable, the remaining provisions will remain in full force and effect. This Agreement constitutes the entire agreement between the parties with respect to the Software and supersedes any conflicting or additional terms contained in any purchase order or elsewhere.

END OF SCHEDULE 1

Schedule 2

If this Linksys product contains open source software licensed under Version 2 of the “GNU General Public License” then the license terms below in this Schedule 2 will apply to that open source software. The license terms below in this Schedule 2 are from the public web site at

http://www.gnu.org/copyleft/gpl.html

GNU GENERAL PUBLIC LICENSE

Version 2, June 1991

51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA

Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.

Preamble

The licenses for most software are designed to take away your freedom to share and change it. By contrast, the

Page 57

Appendix D

Software License Agreement

GNU General Public License is intended to guarantee your freedom to share and change free software–to make sure the software is free for all its users. This General Public License applies to most of the Free Software Foundation’s software and to any other program whose authors commit to using it. (Some other Free Software Foundation software is covered by the GNU Lesser General Public License instead.) You can apply it to your programs, too.

When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things.

To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it.

For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights.

We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software.

Also, for each author’s protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors’ reputations.

Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone’s free use or not licensed at all.

The precise terms and conditions for copying, distribution and modification follow.

TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION

This License applies to any program or other work 0. which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License. The “Program”, below, refers to any such program or work, and a “work based on the Program” means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/ or translated into another language. (Hereinafter, translation is included without limitation in the term “modification”.) Each licensee is addressed as “you”.

Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does.

You may copy and distribute verbatim copies of the 1. Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program.

You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.

You may modify your copy or copies of the Program 2. or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions:

You must cause the modified files to carry a. prominent notices stating that you changed the files and the date of any change.

You must cause any work that you distribute or b. publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License.

Wireless-G ADSL2+ Gateway with VoIP

Page 58

Appendix D

Software License Agreement

If the modified program normally reads commands c. interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.)

These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.

Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Program.

In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.

You may copy and distribute the Program (or a 3. work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following:

Accompany it with the complete corresponding a. machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or,

Accompany it with a written offer, valid for at least b. three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or,

Accompany it with the information you received as c. to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.)

The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.

If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code.

You may not copy, modify, sublicense, or distribute 4. the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.

You are not required to accept this License, since you 5. have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it.

Each time you redistribute the Program (or any work 6. based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License.

Wireless-G ADSL2+ Gateway with VoIP

Page 59

Appendix D

Software License Agreement

If, as a consequence of a court judgment or allegation 7. of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program.

If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances.

It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.

This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.

If the distribution and/or use of the Program is 8. restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.

The Free Software Foundation may publish revised 9. and/or new versions of the General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.

Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and “any later version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Program does

Wireless-G ADSL2+ Gateway with VoIP

not specify a version number of this License, you may choose any version ever published by the Free Software Foundation.

If you wish to incorporate parts of the Program into 10. other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.

NO WARRANTY

BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, 11. THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.

IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR 12. AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

END OF TERMS AND CONDITIONS

END OF SCHEDULE 2

Schedule 3

If this Linksys product contains open source software licensed under Version 2.1 of the “GNU Lesser General Public License” then the license terms below in this Schedule 3 will apply to that open source software. The license terms below in this Schedule 3 are from the public web site at

http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html

Page 60

Appendix D

Software License Agreement

GNU LESSER GENERAL PUBLIC LICENSE

Version 2.1, February 1999

51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA

Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.

[This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the version number 2.1.]

Preamble

The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public Licenses are intended to guarantee your freedom to share and change free software—to make sure the software is free for all its users.

This license, the Lesser General Public License, applies to some specially designated software packages—typically libraries—of the Free Software Foundation and other authors who decide to use it. You can use it too, but we suggest you first think carefully about whether this license or the ordinary General Public License is the better strategy to use in any particular case, based on the explanations below.

When we speak of free software, we are referring to freedom of use, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish); that you receive source code or can get it if you want it; that you can change the software and use pieces of it in new free programs; and that you are informed that you can do these things.

To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it.

For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You must make sure that they, too, receive or can get the source code. If you link other code with the library, you must provide complete object files to the recipients, so that they can relink them with the library after making changes to the library and recompiling it. And you must show them these terms so they know their rights.

We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which gives you legal permission to copy, distribute and/ or modify the library.

To protect each distributor, we want to make it very clear that there is no warranty for the free library. Also, if the library is modified by someone else and passed on, the recipients should know that what they have is not the original version, so that the original author’s reputation will not be affected by problems that might be introduced by others.

Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that a company cannot effectively restrict the users of a free program by obtaining a restrictive license from a patent holder. Therefore, we insist that any patent license obtained for a version of the library must be consistent with the full freedom of use specified in this license.

Most GNU software, including some libraries, is covered by the ordinary GNU General Public License. This license, the GNU Lesser General Public License, applies to certain designated libraries, and is quite different from the ordinary General Public License. We use this license for certain libraries in order to permit linking those libraries into non-free programs.

When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally speaking a combined work, a derivative of the original library. The ordinary General Public License therefore permits such linking only if the entire combination fits its criteria of freedom. The Lesser General Public License permits more lax criteria for linking other code with the library.

We call this license the “Lesser” General Public License because it does Less to protect the user’s freedom than the ordinary General Public License. It also provides other free software developers Less of an advantage over competing non-free programs. These disadvantages are the reason we use the ordinary General Public License for many libraries. However, the Lesser license provides advantages in certain special circumstances.

For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain library, so that it becomes a de-facto standard. To achieve this, non-free programs must be allowed to use the library. A more frequent case is that a free library does the same job as widely used non-free libraries. In this case, there is little to gain by limiting the free library to free software only, so we use the Lesser General Public License.

In other cases, permission to use a particular library in nonfree programs enables a greater number of people to use a large body of free software. For example, permission to use the GNU C Library in non-free programs enables many more people to use the whole GNU operating system, as well as its variant, the GNU/Linux operating system.

Although the Lesser General Public License is Less protective of the users’ freedom, it does ensure that the user of a program that is linked with the Library has the

Wireless-G ADSL2+ Gateway with VoIP

Page 61

Appendix D

Software License Agreement

freedom and the wherewithal to run that program using a modified version of the Library.

The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the difference between a “work based on the library” and a “work that uses the library”. The former contains code derived from the library, whereas the latter must be combined with the library in order to run.

GNU LESSER GENERAL PUBLIC LICENSE

TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION

This License Agreement applies to any software library 0. or other program which contains a notice placed by the copyright holder or other authorized party saying it may be distributed under the terms of this Lesser General Public License (also called “this License”). Each licensee is addressed as “you”.

A “library” means a collection of software functions and/or data prepared so as to be conveniently linked with application programs (which use some of those functions and data) to form executables.

The “Library”, below, refers to any such software library or work which has been distributed under these terms. A “work based on the Library” means either the Library or any derivative work under copyright law: that is to say, a work containing the Library or a portion of it, either verbatim or with modifications and/or translated straightforwardly into another language. (Hereinafter, translation is included without limitation in the term “modification”.)

“Source code” for a work means the preferred form of the work for making modifications to it. For a library, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the library.

Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running a program using the Library is not restricted, and output from such a program is covered only if its contents constitute a work based on the Library (independent of the use of the Library in a tool for writing it). Whether that is true depends on what the Library does and what the program that uses the Library does.

Wireless-G ADSL2+ Gateway with VoIP

You may copy and distribute verbatim copies of the 1. Library’s complete source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and distribute a copy of this License along with the Library.

You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.

You may modify your copy or copies of the Library or 2. any portion of it, thus forming a work based on the Library, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions:

The modified work must itself be a software a) library.

You must cause the files modified to carry b) prominent notices stating that you changed the files and the date of any change.

You must cause the whole of the work to be c) licensed at no charge to all third parties under the terms of this License.

If a facility in the modified Library refers to a function d) or a table of data to be supplied by an application program that uses the facility, other than as an argument passed when the facility is invoked, then you must make a good faith effort to ensure that, in the event an application does not supply such function or table, the facility still operates, and performs whatever part of its purpose remains meaningful.

(For example, a function in a library to compute square roots has a purpose that is entirely welldefined independent of the application. Therefore, Subsection 2d requires that any applicationsupplied function or table used by this function must be optional: if the application does not supply it, the square root function must still compute square roots.)

These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Library, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Library, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.

Page 62

Appendix D

Software License Agreement

In addition, mere aggregation of another work not based on the Library with the Library (or with a work based on the Library) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.

You may opt to apply the terms of the ordinary GNU 3. General Public License instead of this License to a given copy of the Library. To do this, you must alter all the notices that refer to this License, so that they refer to the ordinary GNU General Public License, version 2, instead of to this License. (If a newer version than version 2 of the ordinary GNU General Public License has appeared, then you can specify that version instead if you wish.) Do not make any other change in these notices.

Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public License applies to all subsequent copies and derivative works made from that copy.

This option is useful when you wish to copy part of the code of the Library into a program that is not a library.

You may copy and distribute the Library (or a portion 4. or derivative of it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange.

If distribution of object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place satisfies the requirement to distribute the source code, even though third parties are not compelled to copy the source along with the object code.

A program that contains no derivative of any portion 5. of the Library, but is designed to work with the Library by being compiled or linked with it, is called a “work that uses the Library”. Such a work, in isolation, is not a derivative work of the Library, and therefore falls outside the scope of this License.

However, linking a “work that uses the Library” with the Library creates an executable that is a derivative of the Library (because it contains portions of the Library), rather than a “work that uses the library”. The executable is therefore covered by this License. Section 6 states terms for distribution of such executables.

When a “work that uses the Library” uses material from a header file that is part of the Library, the object code for the work may be a derivative work of the Library even though the source code is not. Whether this is true is especially significant if the work can be linked without the Library, or if the work is itself a library. The threshold for this to be true is not precisely defined by law.

If such an object file uses only numerical parameters, data structure layouts and accessors, and small macros and small inline functions (ten lines or less in length), then the use of the object file is unrestricted, regardless of whether it is legally a derivative work. (Executables containing this object code plus portions of the Library will still fall under Section 6.)

Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of Section 6. Any executables containing that work also fall under Section 6, whether or not they are linked directly with the Library itself.

As an exception to the Sections above, you may also 6. combine or link a “work that uses the Library” with the Library to produce a work containing portions of the Library, and distribute that work under terms of your choice, provided that the terms permit modification of the work for the customer’s own use and reverse engineering for debugging such modifications.

You must give prominent notice with each copy of the work that the Library is used in it and that the Library and its use are covered by this License. You must supply a copy of this License. If the work during execution displays copyright notices, you must include the copyright notice for the Library among them, as well as a reference directing the user to the copy of this License. Also, you must do one of these things:

Accompany the work with the complete a) corresponding machine-readable source code for the Library including whatever changes were used in the work (which must be distributed under Sections 1 and 2 above); and, if the work is an executable linked with the Library, with the complete machine-readable “work that uses the Library”, as object code and/or source code, so that the user can modify the Library and then relink to produce a modified executable containing the modified Library. (It is understood that the user who changes the contents of definitions files in the Library will not necessarily be able to recompile the application to use the modified definitions.)

Wireless-G ADSL2+ Gateway with VoIP

Page 63

Appendix D

Software License Agreement

Use a suitable shared library mechanism for linking b) with the Library. A suitable mechanism is one that (1) uses at run time a copy of the library already present on the user’s computer system, rather than copying library functions into the executable, and (2) will operate properly with a modified version of the library, if the user installs one, as long as the modified version is interface-compatible with the version that the work was made with.

Accompany the work with a written offer, valid c) for at least three years, to give the same user the materials specified in Subsection 6a, above, for a charge no more than the cost of performing this distribution.

If distribution of the work is made by offering access d) to copy from a designated place, offer equivalent access to copy the above specified materials from the same place.

Verify that the user has already received a copy of e) these materials or that you have already sent this user a copy.

For an executable, the required form of the “work that uses the Library” must include any data and utility programs needed for reproducing the executable from it. However, as a special exception, the materials to be distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.

It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating system. Such a contradiction means you cannot use both them and the Library together in an executable that you distribute.

You may place library facilities that are a work based 7. on the Library side-by-side in a single library together with other library facilities not covered by this License, and distribute such a combined library, provided that the separate distribution of the work based on the Library and of the other library facilities is otherwise permitted, and provided that you do these two things:

Accompany the combined library with a copy of the a) same work based on the Library, uncombined with any other library facilities. This must be distributed under the terms of the Sections above.

Give prominent notice with the combined library of b) the fact that part of it is a work based on the Library, and explaining where to find the accompanying uncombined form of the same work.

You may not copy, modify, sublicense, link with, or 8. distribute the Library except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense, link with, or distribute the Library is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.

You are not required to accept this License, since you 9. have not signed it. However, nothing else grants you permission to modify or distribute the Library or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Library (or any work based on the Library), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Library or works based on it.

Each time you redistribute the Library (or any work 10. based on the Library), the recipient automatically receives a license from the original licensor to copy, distribute, link with or modify the Library subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties with this License.

If, as a consequence of a court judgment or allegation 11. of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Library at all. For example, if a patent license would not permit royalty-free redistribution of the Library by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Library.

If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply, and the section as a whole is intended to apply in other circumstances.

Wireless-G ADSL2+ Gateway with VoIP

Page 64

Appendix D

Software License Agreement

software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.

This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.

If the distribution and/or use of the Library is restricted 12. in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Library under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.

The Free Software Foundation may publish revised 13. and/or new versions of the Lesser General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.

Each version is given a distinguishing version number. If the Library specifies a version number of this License which applies to it and “any later version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Library does not specify a license version number, you may choose any version ever published by the Free Software Foundation.

BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, 15. THERE IS NO WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE LIBRARY “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.

IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW 16. OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

END OF TERMS AND CONDITIONS

END OF SCHEDULE 3

If you wish to incorporate parts of the Library into 14. other free programs whose distribution conditions are incompatible with these, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.

NO WARRANTY

Schedule 4

If this Linksys product contains open source software licensed under the OpenSSL license:

This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/).

This product includes cryptographic software written by Eric Young (eay@cryptsoft.com).

This product includes software written by Tim Hudson (tjh@cryptsoft.com).

In addition, if this Linksys product contains open source software licensed under the OpenSSL license then the license terms below in this Schedule 3 will apply to that open source software. The license terms below in this Schedule 3 are from the public web site at http://www.openssl.org/source/license.html.

The OpenSSL toolkit stays under a dual license, i.e. both the conditions of the OpenSSL License and the original SSLeay license apply to the toolkit. See below for the actual license texts. Actually both licenses are BSD-style Open Source licenses. In case of any license issues related to OpenSSL please contact openssl-core@openssl.org.

Wireless-G ADSL2+ Gateway with VoIP

Page 65

Appendix D

Software License Agreement

OpenSSL License

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

Redistributions of source code must retain the above 1. copyright notice, this list of conditions and the following disclaimer.

Redistributions in binary form must reproduce the 2. above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

All advertising materials mentioning features or 3. use of this software must display the following acknowledgment: “This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/)”

The names “OpenSSL Toolkit” and “OpenSSL Project” 4. must not be used to endorse or promote products derived from this software without prior written permission. For written permission, please contact openssl-core@openssl.org.

Products derived from this software may not be called 5. “OpenSSL” nor may “OpenSSL” appear in their names without prior written permission of the OpenSSL Project.

Redistributions of any form whatsoever must retain 6. the following acknowledgment: “This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org/)”

THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT “AS IS” AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

This product includes cryptographic software written by Eric Young (eay@cryptsoft.com). This product includes software written by Tim Hudson (tjh@cryptsoft.com).

Original SSLeay License

This package is an SSL implementation written by Eric Young (eay@cryptsoft.com).

The implementation was written so as to conform with Netscape’s SSL.

This library is free for commercial and non-commercial use as long as the following conditions are adhered to. The following conditions apply to all code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL code. The SSL documentation included with this distribution is covered by the same copyright terms except that the holder is Tim Hudson (tjh@cryptsoft. com).

If this package is used in a product, Eric Young should be given attribution as the author of the parts of the library used. This can be in the form of a textual message at program startup or in documentation (online or textual) provided with the package.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

Redistributions of source code must retain the 1. copyright notice, this list of conditions and the following disclaimer.

All advertising materials mentioning features or 3. use of this software must display the following acknowledgement:

“This product includes cryptographic software written by Eric Young (eay@cryptsoft.com)”

The word ‘cryptographic’ can be left out if the routines from the library being used are not cryptographic related.

If you include any Windows specific code (or a derivative 4. thereof) from the apps directory (application code) you must include an acknowledgement: “This product includes software written by Tim Hudson (tjh@ cryptsoft.com)”

THIS SOFTWARE IS PROVIDED BY ERIC YOUNG “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY

Wireless-G ADSL2+ Gateway with VoIP

Page 66

Appendix D

DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

The license and distribution terms for any publicly available version or derivative of this code cannot be changed. i.e. this code cannot simply be copied and put under another distribution license [including the GNU Public License.]

END OF SCHEDULE 4

Software License Agreement

Wireless-G ADSL2+ Gateway with VoIP

8072410NC-JL