Cisco Aironet Dual-Band MIMO Wall-Mounted
Omnidirectional Antenna (AIR-ANT2544V4M-R)
This document outlines the specifications for the Cisco Aironet 2.4-GHz/5-GHz Dual-Band MIMO
Wall-Mounted Omnidirectional Antenna (AIR-ANT2544V4M-R) and provides instructions for
mounting it. The antenna operates in the 2.4- and 5-GHz frequency ranges and is designed for indoor or
outdoor use.
The following information is provided in this document.
• Technical Specifications, page 2
• System Requirements, page 4
• Safety Precautions, page 5
• Installation Notes, page 6
• Installing the Antenna, page 7
• Suggested Cable, page 13
• Obtaining Documentation and Submitting a Service Request, page 13
Americas Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
© 2012 Cisco Systems, Inc. All rights reserved.
Technical Specifications
Technical Specifications
Table 1 AIR-ANT2544V4M-R Dual-Band MIMO Wall-Mounted Omnidirectional Antenna
Specifications
Antenna type 4-element MIMO
omnidirectional
Operating frequency
range
Nominal input
impedance
VSWR 2:1 or less
Peak gain 2.4-GHz band: 4 dBi
Polarization Linear, vertical
Azimuth plane
(3 dB beamwidth)
Elevation plane
(3 dB beamwidth
Length 8.6 in (21.8 cm)
Diameter 6.3 in (16 cm)
Weight Antenna: 1.48 lb.
Cable 3-ft. (91.4 cm) plenum
Connector RP-TNC
Environment Indoor/outdoor
Temperature range -22° F to 158° F
2400–2484 MHz
5150–5850 MHz
50Ω
5-GHz band: 4 dBi
Ominidirectional
2.4-GHz band: 60°
5-GHz band: 33°
(671.5 g);
(-30° C to 70° C)
332312
Cisco Aironet Dual-Band MIMO Wall-Mounted Omnidirectional Antenna (AIR-ANT2544V4M-R)
2
78-20770-01
Technical Specifications
The figures below show the azimuth plane patterns (indicated by red lines) and elevation plane patterns
(indicated by blue lines) for each element in the antenna.
2.4-GHz Antenna 1 Azimuth and Elevation Plane Patterns 5-GHz Antenna 1 Azimuth and Elevation Plane Patterns
2.4-GHz Antenna 2 Azimuth and Elevation Plane Patterns 5-GHz Antenna 2 Azimuth and Elevation Plane Patterns
78-20770-01
Cisco Aironet Dual-Band MIMO Wall-Mounted Omnidirectional Antenna (AIR-ANT2544V4M-R)
3
System Requirements
2.4-GHz Antenna 3 Azimuth and Elevation Plane Patterns 5-GHz Antenna 3 Azimuth and Elevation Plane Patterns
2.4-GHz Antenna 4 Azimuth and Elevation Plane Patterns 5-GHz Antenna 4 Azimuth and Elevation Plane Patterns
System Requirements
This antenna is designed for indoor and outdoor use with any Cisco Aironet radio device with dual-band
(2.4- and 5-GHz) RP-TNC connectors.
Cisco Aironet Dual-Band MIMO Wall-Mounted Omnidirectional Antenna (AIR-ANT2544V4M-R)
4
78-20770-01
Safety Precautions
Safety Precautions
Warning
Do not locate the antenna near overhead power lines or other electric light or power circuits, or
where it can come into contact with such circuits. When installing the antenna, take extreme care
not to come into contact with such circuits, as they may cause serious injury or death. For proper
installation and grounding of the antenna, please refer to national and local codes (e.g. U.S.: NFPA 70,
National Electrical Code, Article 810, Canada: Canadian Electrical Code, Section 54).
Statement 280
For your safety, read and follow these safety precautions.
1. Before you install an antenna, contact your Cisco account representative to explain which mounting
method to use for the size and type of antenna that you are about to install.
2. Find someone to help you—installing an antenna is often a two-person job.
3. Select your installation site with safety, as well as performance, in mind. Remember that electric
power lines and phone lines look alike. For your safety, assume that any overhead line can kill you.
4. Contact your electric power company. Tell them your plans and ask them to come look at your
proposed installation.
5. Plan your installation carefully and completely before you begin. Each person involved in an
in stallati o n should be a ssigned t o a specific task, an d should kn ow what t o do and whe n to do it. On e
person should be in charge of the operation to issue instructions and watch for signs of trouble.
6. When installing your antenna, follow these guidelines:
a. Do not use a metal ladder.
b. Do not work on a wet or windy day.
c. Do dress properly—wear shoes with rubber soles and heels, rubber gloves, and a long-sleeved
shirt or jacket.
7. If the assembly starts to drop, move away from it and let it fall. Because the antenna, mast, cable,
and metal guy wires are all excellent conductors of electrical current, even the slightest touch of any
of these parts to a power line completes an electrical path through the antenna and the installer.
8. If any part of the antenna system should come in contact with a power line, do not touch it or try to
remove it yourself. Call your local power company to have it removed safely.
9. If an accident should occur with the power lines, call for qualified emergency help immediately.
78-20770-01
Cisco Aironet Dual-Band MIMO Wall-Mounted Omnidirectional Antenna (AIR-ANT2544V4M-R)
5
Installation Notes
Installation Notes
Antennas transmit and receive radio signals which are susceptible to RF obstructions and common
sources of interference that can reduce throughput and range of the device to which they are connected.
Follow these guidelines to ensure the best possible performance:
• Install the antenna vertically and mount it with the cables pointing towards the ground.
• Keep the antenna away from metal obstructions such as heating and air-conditioning ducts, large
ceiling trusses, building superstructures, and major power cabling runs. If necessary, use a rigid
conduit to lower the antenna away from these obstructions.
• The density of the materials used in a building’s construction determines the number of walls the
signal can pass through and still maintain adequate signal strength. Consider the following before
choosing the location for your antenna:
–
Signals penetrate paper and vinyl walls with little change to signal strength.
–
Signals penetrate only one or two solid and pre-cast concrete walls without degrading signal
strength.
–
Signals penetrate three or four concrete and wood block walls without degrading signal
strength.
–
Signals penetrate five or six walls constructed of drywall or wood without degrading signal
strength.
–
Signals will likely reflect off a thick metal wall and may not penetrate it at all.
–
Signals will likely reflect off a chain link fence or wire mesh spaced between 1 and 1 1/2 in.
(2.5 and 3.8 cm). The fence acts as a harmonic reflector that blocks the signal.
• Install the antenna away from microwave ovens and 2-GHz cordless phones. These products can
cause signal interference because they operate in the same frequency range as the device to which
your antenna is connected.
Choosing a Mounting Location
The antenna should be mounted clear of any obstructions to the sides of the radiating elements.
Generally, the higher an antenna is above the floor, the better it performs. If possible, find a mounting
place directly above your wireless device to ensure the lead-in cable can be as short as possible.
Cisco Aironet Dual-Band MIMO Wall-Mounted Omnidirectional Antenna (AIR-ANT2544V4M-R)
6
78-20770-01
Installing the Antenna
You can install the antenna on any flat vertical surface, on a pole, or on a ceiling. All hardware for
mounting the antenna on a wall or ceiling is provided. If you intend to install your antenna on another
surface, you must provide the appropriate hardware.
Tools and Equipment Required
A mounting installation kit is included with the antenna and consists of the following hardware:
• Mount interface bracket
• Mount base
• Wall bracket
• One 1/4–20 x ½-in. cap screw
• One 1/4–20 wing screw
• Two #10 x ¾-in. screws
• Two #10 x ½-in. screws
• One screen mesh washer
Installing the Antenna
• One spherical washer
• 3/16 allen wrench
• Rubber gasket
• Jam nut
You may need the following tools and equipment, which are not provided.
• A #2 Phillips screwdriver
• A drill and drill bit
• A pencil
• Two hose clamps
78-20770-01
Cisco Aironet Dual-Band MIMO Wall-Mounted Omnidirectional Antenna (AIR-ANT2544V4M-R)
7
Installing the Antenna
Mounting on a Vertical Surface
Follow these steps to mount your antenna on a vertical surface.
Step 1 Attach the antenna bracket to the antenna using the jam nut provided (Figure 1).
Figure 1 Antenna Bracket
Cisco Aironet Dual-Band MIMO Wall-Mounted Omnidirectional Antenna (AIR-ANT2544V4M-R)
8
78-20770-01
Installing the Antenna
Step 2 With the screen mesh washer between the two brackets, attach the antenna bracket to the mounting
bracket using the spherical washer and wing bolt provided (Figure 2).
Figure 2 Antenna Bracket Attached to Mounting Bracket
78-20770-01
Step 3
Step 4 Attach the wall bracket to the wall using the two screws provided (Figure 3).
Determine the mounting location for the antenna.
Cisco Aironet Dual-Band MIMO Wall-Mounted Omnidirectional Antenna (AIR-ANT2544V4M-R)
9
Installing the Antenna
Figure 3 Wall Mounting
Step 5
Slide the mounting bracket onto the wall bracket and secure it in place (optional) with the two screws
provided (Figure 4).
Figure 4 Attaching Mounting Bracket to Wall Bracket
Once the antenna is secured on the wall, you can adjust the azimuth and elevation.
Step 6 To adjust the azimuth and elevation, loosen the bolt that attaches the antenna bracket to the mounting
bracket (Figure 5). Azimuth can be adjusted ±90 degrees. Elevation can be adjusted +15 degrees and -35
degrees.
10
Cisco Aironet Dual-Band MIMO Wall-Mounted Omnidirectional Antenna (AIR-ANT2544V4M-R)
78-20770-01
Figure 5 Azimuth and Elevation Adjustment
Installing the Antenna
Outdoor Installations
You can mount this antenna outdoors. If you mount the antenna outdoors, you must ensure that the
antenna cables exit from the bottom to prevent any water intrusion and to provide a drain for any
moisture that may accumulate inside the antenna.
Mounting on a Ceiling
To mount the antenna on a ceiling, follow these steps:
Step 1 Drill a hole in the ceiling approximately 1.25 in. in diameter.
Step 2 Fit the rubber gasket onto the bottom of the antenna.
Step 3 Insert the antenna shaft through the hole in the ceiling.
Step 4 Thread the jam nut onto the antenna shaft and tighten.
Figure 6 shows the ceiling mount process.
78-20770-01
Cisco Aironet Dual-Band MIMO Wall-Mounted Omnidirectional Antenna (AIR-ANT2544V4M-R)
11
Installing the Antenna
Figure 6 Mounting on a Ceiling
Mounting on a Mast
The antenna can be mounted on a mast rather than on a wall using two 1/2 inch-wide hose clamps (not
provided).
To mount the antenna on a mast, follow these steps:
Step 1 Follow Steps 1 and Step 2 from the “Mounting on a Vertical Surface” section on page 8.
Step 2 Position the antenna, mounting bracket, and hose clamps on the mast.
Step 3 Tighten the hose clamps until the antenna is secure on the mast.
Once the antenna is secured on the mast, you can adjust the azimuth and elevation.
Cisco Aironet Dual-Band MIMO Wall-Mounted Omnidirectional Antenna (AIR-ANT2544V4M-R)
12
78-20770-01
Suggested Cable
Step 4 To adjust the azimuth and elevation, loosen the bolt that attaches the antenna bracket to the mounting
bracket (Figure 5). Azimuth can be adjusted ±90 degrees. Elevation can be adjusted +15 degrees and -35
degrees.
Suggested Cable
Cisco recommends a high-quality, low-loss cable for use with the antenna.
Note Coaxial cable loses efficiency as the frequency increases, resulting in signal loss. The cable should be
kept as short as possible because cable length also determines the amount of signal loss (the longer the
run, the greater the loss).
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional
information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and
revised Cisco technical documentation, at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed
and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free
service and Cisco currently supports RSS Version 2.0
78-20770-01
Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks
can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word
partner does not imply a partnership relationship between Cisco and any other company. (1005R)
Cisco Aironet Dual-Band MIMO Wall-Mounted Omnidirectional Antenna (AIR-ANT2544V4M-R)
13
Obtaining Documentation and Submitting a Service Request
14
Cisco Aironet Dual-Band MIMO Wall-Mounted Omnidirectional Antenna (AIR-ANT2544V4M-R)
78-20770-01
Loading...