Cisco 2010 Hardware Installation Manual

Download

Cisco 2010 Connected Grid Router Hardware Installation Guide

Americas Headquarters

Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000

800 553-NETS (6387)

Fax: 408 527-0883

Text Part Number: OL-21559-01

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.

The following information is for FCC compliance of Class B devices: This equipment has been tested and found to comply with the lim its for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the equipment causes interference to radio or television reception, which can be determined by turning the equipment off and on, users are encouraged to try to correct the interference by using one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Modifications to this product not authorized by Cisco could void the FCC approval and negate your authority to operate the product.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

IMPLIED, INCLUDING, WITHOUT

CCVP, the Cisco logo, and Welcome to the Human Network are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn is a service mark of Cisco

Systems, Inc.; and Access Registrar, Aironet, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, Cisco, the Cisco Certified Internetwork Expert logo,

Cisco

IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step, Follow Me Browsing, FormShare, GigaDrive, HomeLink, Internet Quotient, IOS, iPhone, IP/TV, iQ Expertise, the iQ logo, iQ Net Readiness Scorecard, iQuick Study, LightStream, Linksys, MeetingPlace, MGX, Networkers, Networking Academy, Network Registrar, PIX, ProConnect, ScriptShare, SMARTnet, StackWise, The Fastest Way to Increase Your Internet Quotient, and TransPath are registered trademarks of Cisco

All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0711R)

Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.

Cisco 2010 Connected Grid Router Hardware Installation Guide

Systems, Inc. and/or its affiliates in the United States and certain other countries.

Preface vii

CHAPTER

1 Overview of the Router 1-1

Chassis Views 1-1

Hardware Features 1-2

Locating Chassis Features and Functions 1-2 Built-in Interface Ports 1-4

Gigabit Ethernet Ports 1-4 USB Console Port 1-4

Removable and Interchangeable Modules and Cards 1-5

Grid Router WAN Interface Cards 1-5 Memory 1-5 Power Supplies 1-5

Real-Time Clock 1-6

Slot, Port, and Interface Information 1-6

LED Indicators 1-6

Specifications 1-8

2 Preparing for Router Installation 2-1

Safety Recommendations 2-2

Safety with Electricity 2-3 Preventing Electrostatic Discharge Damage 2-3

78-xxxxx-xx

General Site Requirements 2-4

Rack Requirements 2-4

Router Environmental Requirements 2-4

Power Guidelines and Requirements 2-5

Network Cabling Specifications 2-5

Console and Auxiliary Port Considerations 2-5

Console Port Connections 2-5 Auxiliary Port Connections 2-6

Preparing for Network Connections 2-7

Ethernet Connections 2-7 Serial Connections 2-7

Required Tools and Equipment for Installation and Maintenance 2-9

Book Title

iii

Contents

Installation Checklist 2-10

Creating a Site Log 2-10

CHAPTER

3 Installing and Connecting the Router 3-1

What you Need to Know 3-3

Before You Begin 3-4

Unpacking the Router 3-4

Installing the Router in a Rack 3-4

Rack-Mounting the Chassis 3-5

Attaching Rack-Mount Brackets to Cisco 2010 CGR Routers 3-5 Mounting the Router in a Rack 3-6

Connecting Power 3-7

Connecting Power 3-7 Shutting Off Power 3-9

Connecting to a Console Terminal or Modem 3-10

Connecting to the Serial Port with Microsoft Windows 3-10 Connecting to the Console Port with Mac OS X 3-12 Connecting to the Console Port with Linux 3-13

Installing the Cisco Microsoft Windows USB Device Driver 3-13

Installing the Cisco Microsoft Windows XP USB Driver 3-13 Installing the Cisco Microsoft Windows 2000 USB Driver 3-14 Installing the Cisco Microsoft Windows Vista USB Driver 3-14

CHAPTER

Uninstalling the Cisco Microsoft Windows USB Driver 3-15

Uninstalling the Cisco Microsoft Windows XP and 2000 USB Driver 3-15 Uninstalling the Cisco Microsoft Windows Vista USB Driver 3-15

Connecting to the Auxiliary Port 3-16

Connecting WAN and LAN Interfaces 3-17

Ports and Cabling 3-18 Connection Procedures and Precautions 3-18

4 Configuring the Router 4-1

Powering up the Router 4-1

Checklist for Power Up 4-1 Power Up Procedure 4-2 Verifying the Power Supply Side LED Indications 4-3

Performing the Initial Configuration on the Router 4-3

Using Cisco Setup Command Facility 4-3

Completing the Configuration 4-6

Book Title

78-xxxxx-xx

Using Cisco Configuration Professional Express 4-7 Using Cisco IOS CLI—Manual Configuration 4-7

Configuring the Router Hostname 4-8 Configuring the Enable and Enable Secret Passwords 4-9 Configuring the Console Idle Privileged EXEC Timeout 4-10 Configuring Gigabit Ethernet Interfaces 4-12 Specifying a Default Route or Gateway of Last Resort 4-14 Configuring IP Routing and IP Protocols 4-14 Default Routes 4-15 Default Network 4-15 Gateway of Last Resort 4-15 Configuring Virtual Terminal Lines for Remote Console Access 4-17

Configuring the Auxiliary Line 4-19 Verifying Network Connectivity 4-20 Saving Your Router Configuration 4-22 Saving Backup Copies of Configuration and System Image 4-22

Contents

CHAPTER

NDEX

Verifying the Initial Configuration 4-24

5 Installing and Upgrading Internal Modules 5-1

Safety Warnings 5-2

Replacing Power Supplies and Redundant Power Supplies 5-2

Replacing the Cisco 2010 CGR Router Power Supply 5-2

Removing and Installing Compact Flash Memory Cards 5-3

Preventing Electrostatic Discharge Damage 5-3 Removing a Compact Flash Memory Card 5-4 Installing a Compact Flash Memory Card 5-6

Installing SFP Modules 5-7

Laser Safety Guidelines 5-7 Removing SFP Modules 5-8

Installing Grid Router WAN Interface Cards 5-9

78-xxxxx-xx

Book Title

Contents

Book Title

78-xxxxx-xx

Preface

This preface describes the objectives, audience, organization, and conventions of this guide, and describes related documents that have additional information. It contains the following sections:

• Objectives, page vii

• Audience, page vii

• Organization, page viii

• Conventions, page viii

• Searching for Cisco Documents, page xiv

Objectives

Audience

• Obtaining Documentation and Submitting a Service Request, page xv

This guide provides an overview and explains how to install, connect, and perform initial configuration for the Cisco Connected Grid Routers (CGR) 2010.

For warranty, service, and support information, see the “Cisco Warranty Terms” section in the Readme First for the Cisco 2010 CGR document that was shipped with your router.

This documentation is designed for the person installing, configuring, and maintaining the router, who should be familiar with electronic circuitry and wiring practices and has experience as an electronic or electromechanical technician. It identifies certain procedures that should be performed only by trained and qualified personnel.

OL-21559-01

Cisco Connected Grid Routers 2010 Hardware Installation Guide

vii

Organization

This guide includes the following sections:

Chapter Title Description

1 Overview of the Router Describes the chassis views, information for locating the

2 Preparing for Router Installation Describes site requirements and equipment needed to

3 Installing and Connecting the

4 Configuring the Router Describes how to configure your Cisco CGR 2010.

5 Installing and Upgrading Internal

1. PID = product ID.

2. UID = universal device identifier.

Router

Modules

Preface

serial number, PID1, and UDI2, general hardware features, slot, port, and interface information, and LED indicators,

install the routers.

Provides information about mounting the router and connecting the cables needed to install your Cisco 2010 CGR.

Describes how to connect your Cisco CGR 2010 to a power source and to networks and external devices.

Conventions

This document uses the following conventions:

Convention Indication

bold font Commands and keywords and user-entered text appear in bold font.

italic font Document titles, new or emphasized terms, and arguments for which you supply

values are in italic font.

[ ] Elements in square brackets are optional.

{x | y | z } Required alternative keywords are grouped in braces and separated by

vertical

[ x | y | z ] Optional alternative keywords are grouped in brackets and separated by

vertical

string A nonquoted set of characters. Do not use quotation marks around the string or

the string will include the quotation marks.

courier font Terminal sessions and information the system displays appear in courier font.

< > Nonprinting characters such as passwords are in angle brackets.

[ ] Default responses to system prompts are in square brackets.

!, # An exclamation point (!) or a pound sign (#) at the beginning of a line of code

indicates a comment line.

bars.

viii

Note Means reader take note.

Cisco Connected Grid Routers 2010 Hardware Installation Guide

OL-21559-01

Preface

Tip Means the following information will help you solve a problem.

Caution Means reader be careful. In this situation, you might perform an action that could result in equipment

damage or loss of data.

Warning

Waarschuwing

Varoitus

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device.

Statement 1071

SAVE THESE INSTRUCTIONS

BELANGRIJKE VEILIGHEIDSINSTRUCTIES

Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt raadplegen.

BEWAAR DEZE INSTRUCTIES

TÄRKEITÄ TURVALLISUUSOHJEITA

Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien lausuntonumeroiden avulla.

OL-21559-01

Attention

SÄILYTÄ NÄMÄ OHJEET

IMPORTANTES INFORMATIONS DE SÉCURITÉ

Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil, référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.

CONSERVEZ CES INFORMATIONS

Cisco Connected Grid Routers 2010 Hardware Installation Guide

Preface

Warnung

Avvertenza

Advarsel

WICHTIGE SICHERHEITSHINWEISE

Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.

BEWAHREN SIE DIESE HINWEISE GUT AUF.

IMPORTANTI ISTRUZIONI SULLA SICUREZZA

Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento.

CONSERVARE QUESTE ISTRUZIONI

VIKTIGE SIKKERHETSINSTRUKSJONER

Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne enheten.

Aviso

¡Advertencia!

TA VARE PÅ DISSE INSTRUKSJONENE

INSTRUÇÕES IMPORTANTES DE SEGURANÇA

Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.

GUARDE ESTAS INSTRUÇÕES

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo.

GUARDE ESTAS INSTRUCCIONES

Cisco Connected Grid Routers 2010 Hardware Installation Guide

OL-21559-01

Preface

Varning!

VIKTIGA SÄKERHETSANVISNINGAR

Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning.

SPARA DESSA ANVISNINGAR

OL-21559-01

Cisco Connected Grid Routers 2010 Hardware Installation Guide

Preface

Aviso

Advarsel

INSTRUÇÕES IMPORTANTES DE SEGURANÇA

Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo.

GUARDE ESTAS INSTRUÇÕES

VIGTIGE SIKKERHEDSANVISNINGER

Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de oversatte advarsler, der fulgte med denne enhed.

GEM DISSE ANVISNINGER

xii

Cisco Connected Grid Routers 2010 Hardware Installation Guide

OL-21559-01

Preface

OL-21559-01

Cisco Connected Grid Routers 2010 Hardware Installation Guide

xiii

Preface

Access the Regulatory Compliance and Safety Information for Cisco 2010 Connected Grid Router at:

http://www.cisco.com/en/US/docs/routers/access/2000/CGR2010/hardware/rcsi/rcsiCGR2000series.ht ml

Warning

Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool.

Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.

Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.

Statement 1038

Searching for Cisco Documents

To search a HTML document using a web browser, press Ctrl-F (Windows) or Cmd-F (Apple). In most browsers, the option to search whole words only, invoke case sensitivity, or search forward and backward is also available.

Statement 1035

Statement 1037

xiv

Cisco Connected Grid Routers 2010 Hardware Installation Guide

OL-21559-01

Preface

To search a PDF document in Adobe Reader, use the basic Find toolbar (Ctrl-F) or the Full Reader Search window (Shift-Ctrl-F). Use the Find toolbar to find words or phrases within a specific document. Use the Full Reader Search window to search multiple PDF files simultaneously and to change case sensitivity and other options. Adobe Reader online help has more information about how to search PDF documents.

Obtaining Documentation and Submitting a Service Request

For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s revised Cisco

http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html

Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS

technical documentation, at:

New in Cisco Product Documentation, which also lists all new and

Ve rs i on 2.0.

OL-21559-01

Cisco Connected Grid Routers 2010 Hardware Installation Guide

Preface

xvi

Cisco Connected Grid Routers 2010 Hardware Installation Guide

OL-21559-01

CHA PTER

Overview of the Router

The Cisco Connected Grid Router (CGR) 2010 is the first router in the Cisco 2000 Series Connected Grid solutions. The 2010 CGR is a ruggedized power utility substation router, which offers data functionality through Gigabit Ethernet ports, and security functionality with a VPN accelerator. Ruggedized routers comply with specifications IEEE 1613 and IEC 61850, for products that meet stringent environmental, surge, and electromagnetic Interference (EMI) requirements for utility substation environments without moving parts or fans.

This Cisco 2010 CGR router has new rugged grid router WAN interface card (GRWIC) slots that support the rugged product power utility market.

This chapter includes the following sections:

• Chassis Views, page 1-1

• Hardware Features, page 1-2

• Slot, Port, and Interface Information, page 1-6

• LED Indicators, page 1-6

• Specifications, page 1-8

Chassis Views

This section contains views of the power supply side and cable side panels of the Cisco 2010 CGR, showing locations of the interfaces, module slots, status indicators, and chassis identification labels.

Figure 1-1 shows Cisco 2010 CGR chassis, Figure 1-2 shows the power supply side view of the Cisco

2010 CGR, and Figure 1-3 shows the cable side panel of the Cisco 2010 CGR.

OL-21559-01

Cisco Connected Grid Routers 2010 Hardware Installation Guide

1-1

Hardware Features

Figure 1-1 Cisco 2010 CGR Router Chassis

Cisco CGR 2010

PSU2PSU1

+ Lo

- Lo +

ACT

SFP 0/0

SFP 0/1

SPD

SYS 0

Figure 1-2 Power Supply Side View of the Cisco 2010 CGR

SLOT 3 SLOT 2

GE 0/1

AUX

GE 0/0

CONSOLE

SLOT 1 SLOT 0

CONN CONN

0-3

4-7

CD/LP AL CD/LP AL

P1 P0

Chapter 1 Overview of the Router

277400

PWR-150W-HV

PSU OK

CAUTION: This unit may have more than one power source. Disconnect all power sources before servicing to avoid electric shock.

Figure 1-3 Cable Side View of the Cisco 2010 CGR

Cisco CGR 2010

PSU2

+ Lo

Lo +

PSU1

Hardware Features

This section describes the hardware features in Cisco 2010 CGR.

• Locating Chassis Features and Functions, page 1-2

• Built-in Interface Ports, page 1-4

• Removable and Interchangeable Modules and Cards, page 1-5

PWR-150W-HV

PSU OK

PSU1 PSU2

SFP 0/1 EN

ACT

SYS SPD SPD SPD SPD 2 0 1

SFP 0/0

SPD

SFP

SFP 0/1

SLOT

0/0

0/1

0/0

LINK

SYS 0 1

CF1PS

2ACT

USB CON

CONSOLE

GE 0/1

GE 0/0

PSU

231

AUX

CONSOLE

CF1

DO NOT REMOVE DURING

NETWORK OPERATION

SLOT 3 SLOT 2 SLOT 1 SLOT 0

CF0

DO NOT REMOVE DURING

NETWORK OPERATION

PS Type

Input Rating Per Sources

LoV dc

24-60V

HiV dc

100-270V

V ac, 50/60 Hz

100-240V ~

Cisco Connected Grid Router 2000 Series

CONN CONN

0-3

GRWIC–8A/8-232

P1 P0

4-7

10A 2A 2A

277398

GRWIC–2CE1T1-PRI

CD/LP AL CD/LP AL

277397

• Real-Time Clock, page 1-6

Locating Chassis Features and Functions

Figure 1-4 shows the different chassis features and functions available on the power supply side view of

the Cisco 2010 CGR. Figure 1-5 shows the different chassis features and functions available on the cable side view of the Cisco 2010 CGR.

Cisco Connected Grid Routers 2010 Hardware Installation Guide

1-2

OL-21559-01

Chapter 1 Overview of the Router

GE 0/0

GE 0/1

CONSOLE

1PS2

AUX

Figure 1-4 Power Supply Side View Features and Functions on the Cisco 2010 CGR

Hardware Features

PWR-150W-HV

PSU OK

PSU1 PSU2

SFP 0/1 EN

CAUTION: This unit may have more than one power source. Disconnect all power sources before servicing to avoid electric shock.

3 4

ACT

SYS SPD SPD SPD SPD 2 0 1

SLOT

SFP

0/0

0/1

0/0

LINK

USB CON

CONSOLE

PSU

231

CF1

DO NOT REMOVE DURING

NETWORK OPERATION

PWR-150W-HV

PSU OK

CF0

DO NOT REMOVE DURING

NETWORK OPERATION

Input Terminal

Input Rating

Type

Symbol

Lo 24 - 60 V 10A

100-250V

100-240V 50-60 Hz

Per Source

Lo V DC

Hi V DC

V AC

Cisco Connected Grid Router 2000 Series

1 Kensington security slot 2 Caution label and statement for multiple

power source

3 Power supply unit 1 (PSU1) label 4 Power supply power range label

Figure 1-5 Cable Side View Features and Functions on the Cisco 2010 CGR

248945

Cisco CGR 2010

PSU2

+ Lo

Lo +

PSU1

1 65

SFP 0/0

SPD

2 3 7 98

1 Terminal blocks

CF1PS

SYS 0 1

SFP 0/1

3 USB2 serial console port

GE 0/1

2ACT

GE 0/0

AUX

CONSOLE

SLOT 3 SLOT 2 SLOT 1 SLOT 0

CONN CONN

0-3

GRWIC–8A/8-232

4-7

CD/LP AL CD/LP AL

P1 P0

2 USB0 and USB1 (1, top) 4 SFP0/0 and SFP0/1

GRWIC–2CE1T1-PRI

277445

5 100/1000 Ethernet port (GE0/0 and GE0/1) 6 RJ-45 aux port and serial console port 7 GRWIC slot3 3 (slot cover showing)

8 GRWIC slot 1 (8-port dual RS-232 serial

interface showing)

9 GRWIC slot 04 (T1/E1 dual port interface

showing)

1. Enables AC power, high-voltage DC power, and low-voltage DC power input for dual power supplies.

2. USB = Universal serial bus.

3. Four slots with two removable dividers allow the following install options: 4 single-wide GRWICs; 2 single-wide GRWICs and 1 double-wide GRWIC cover; 2 double-wide GRWIC covers (double-wide GRWIC modules are not yet supported on the Cisco 2010 CGR).

OL-21559-01

Cisco Connected Grid Routers 2010 Hardware Installation Guide

1-3

Hardware Features

4. GRWIC slots 0, 1, 2, and 3 (0, far right).

5. For T1/E1 interfaces, shielded cables are required to meet EN55022, Cispr 22, and EN300-386 compliance.

Built-in Interface Ports

Table 1-1 summarizes the interface ports built into the router chassis.

Ta b l e 1-1 Summary of Cisco 2010 CGR Built-In Interfaces

Router Model

Cisco 2010 CGR

Gigabit Ethernet Ports

Chapter 1 Overview of the Router

Data Ports Management Ports

10/100/1000 GE RJ-45

2 2 2 1 1 1

100/1000 SFP

USB Type A

Console, Serial, RJ-45

Console, Mini-USB (Type B)

Auxiliary, RJ-45

GE Ports

SFP Ports

There are two different types of GE ports available on Cisco 2010 CGR.

• GE Ports, page 1-4

• SFP Ports, page 1-4

The GE RJ-45 copper interface ports support 100BASE-TX and 1000BASE-T.

The small form factor pluggable (SFP) ports on the Cisco 2010 CGR support the following rugged SFP SKUs:

• GLC-FE-100FX-RGD=

• GLC-FE-100LX-RGD=

• GLC-SX-MM-RGD=

• GLC-LX-SM-RGD=

• GLC-ZX-SM-RGD=

The SFP port shares the same physical port as an RJ-45 GE port.

The SFP port can be configured for the following behaviors:

• Always use the RJ-45 port.

• Always use the SFP port.

USB Console Port

Cisco Connected Grid Routers 2010 Hardware Installation Guide

1-4

The Mini-USB type B port has been enabled to perform management tasks on the router. To use this port, you must install a Windows USB device driver before establishing physical connectivity between a personal computer and the router. See the

“Installing the Cisco Microsoft Windows USB Device Driver”

section on page 3-13 for driver installation instructions.

OL-21559-01

Chapter 1 Overview of the Router

Removable and Interchangeable Modules and Cards

GRWICs and power supply units (PSU) for the Cisco 2010 CGR fit into external slots and can be removed or replaced without opening the chassis.

Note See Installing Cisco Interface Cards in Cisco Access Routers document at:

http://www.cisco.com/en/US/docs/routers/access/interfaces/ic/hardware/installation/guide/inst_ic.html

for instructions that describe how to install GRWICs in the router.

Grid Router WAN Interface Cards

GRWICs are the latest generation of interface cards. GRWICs are installed in the GRWIC slot on the router (see

You can install four single-wide GRWICs in the Cisco 2010 CGR router slots at any one time.

Memory

Figure 5-8).

Hardware Features

Power Supplies

Note Any combination of power supplies can be inserted into the chassis. Dual power supply configurations

Cisco 2010 CGR routers contain the following types of memory:

• DDR2—Stores the running configuration and routing tables, and is used for packet buffering by the

network interfaces. Cisco DDR2.

• Boot/NVRAM—Stores the bootstrap program (ROM monitor), the configuration register, and the

startup configuration.

• Flash memory—External flash memory. Stores the operating system software image. Supports 2

external 4 GB I-temp compact flash memory cards.

Cisco 2010 CGR supports two PSUs. Power supplies are field replaceable, externally accessible, and hot swappable. The two power supply options are:

• Low-voltage DC power supply

• AC or high-voltage DC power supply

are load sharing in redundancy mode. A single power supply is sufficient for supporting power needs to the system.

IOS software executes from DRAM memory. Supports 1-GB on board

OL-21559-01

Caution Two types of power supplies are supported on the Cisco 2010 CGR: a low-voltage DC power supply and

a high-voltage DC/AC power supply. Take caution when selecting the correct input voltage for the power supply installed or damage will result.

For this release, only the high-voltage AC power supply is available.

Table 1-2 summarizes the power options.

Cisco Connected Grid Routers 2010 Hardware Installation Guide

1-5

Slot, Port, and Interface Information

Ta b l e 1-2 Cisco 2010 CGR Power Options

Chapter 1 Overview of the Router

Model AC AC + POE DC Hot Swap Internal RPS

2010 CGR Yes No Ye s Yes Yes No

1. Internal RPS means that additional power supply can be added to the PS2 slot.

2. Dual DC means two separate DC inputs to the same power supply.

Real-Time Clock

Upon system power up, the internal real-time clock with battery backup provides the system software with time of day. This allows the system to verify the validity of the certification authority (CA) certificate. The Cisco 2010 CGR has a lithium battery. This battery lasts the life of the router under the operating environmental conditions specified for the router and is not field-replaceable.

Note If the lithium battery in a Cisco 2010 CGR should fail, the router must be returned to Cisco for repair.

Slot, Port, and Interface Information

On the Cisco 2010 CGR, the numbering format for slots and ports is defined as follows: interface type 0/slot/port. “0” indicates slots that are built into the chassis of a router.

Dual DC

LED Indicators

Figure 1-7 summarizes the LED indicators that are located on the router bezel or chassis, but not on the

removable interface cards.

Figure 1-6 Power Supply Side View LEDs on the Cisco 2010 CGR

1 PSU1 OK LED 2 ACT2 and SYS3 LEDs 3 SFP0/14 EN5 SPD6 LEDs 4 GE0/17 LNK8 and SPD LED

PWR-150W-HV

PSU OK

PSU1 PSU2

SFP 0/1 EN

CAUTION: This unit may have more than one power source. Disconnect all power sources before servicing to avoid electric shock.

ACT

SYS SPD SPD SPD SPD 2 0 1

1 98

SLOT

SFP

0/0

0/1

0/0

LINK

USB

LINK

CON

CONSOLE

PWR-150W-HV

PSU OK

Input Terminal

Input Rating

Type

Symbol

PSU

231

CF1

DO NOT REMOVE DURING

NETWORK OPERATION

CF0

DO NOT REMOVE DURING

NETWORK OPERATION

Lo V DC

Hi V DC

V AC

Cisco Connected Grid Router 2000 Series

Lo 24 - 60 V

100-250V

100-240V

50-60 Hz

Per Source

10A

277566

1-6

Cisco Connected Grid Routers 2010 Hardware Installation Guide

OL-21559-01

Chapter 1 Overview of the Router

GRWIC–2CE1T1-PRI

CD/LP AL CD/LP AL

P1 P0

1 PSU1 OK LED 2 ACT2 and SYS3 LEDs 5 SLOT LEDs (slots 0 through 3) 6 Console/USB connection LEDs 7 PSU1/2 LEDs 8 Compact flash slot 1 LED 9 PSU OK LED 10 Compact flash slot 0 LED

1. PSU = Power supply unit

2. ACT = Activity

3. SYS = System

4. SFP = Small form-factor pluggable module slots 0 and 1

5. EN = Enable

6. SPD = Speed

7. GE = Gigabit Ethernet slots 0 and 1

8. LNK = Link

Figure 1-7 Cable Side Vie w LEDs on the Cisco 2010 CGR

LED Indicators

Cisco CGR 2010

PSU2

+ Lo

Lo +

PSU1

SFP 0/0

SFP 0/1

SPD

CF1PS

SYS 0 1

GE 0/1

2ACT

GE 0/0

AUX

CONSOLE

SLOT 3 SLOT 2 SLOT 1 SLOT 0

CONN CONN

0-3

GRWIC–8A/8-232

P1 P0

4-7

GRWIC–2CE1T1-PRI

CD/LP AL CD/LP AL

277567

2 5

6 8

1 EN (enable USB console) 2 SFP1 EN and SPD LEDs 3 ACT status and SYS status LEDs 4 Compact flash 0 and 1 (0, bottom, 1, top) 5 PSU1 (bottom), PSU2 (top) 6 EN (enable RJ-45 console) 7 GRWIC serial interface CONN LED 8 GRWIC serial interface CONN LED 9 Dual-port T1/E1 GRWIC CD/LP LED 10 Dual-port T1/E1 GRWIC AL LED

1. SFP = Small form factor pluggable.

For LED troubleshooting information, including possible trouble causes and corrective actions, see

Table 1-3.

OL-21559-01

Cisco Connected Grid Routers 2010 Hardware Installation Guide

1-7

Specifications

Chapter 1 Overview of the Router

Ta b l e 1-3 Cisco 2010 CGR LED Indicators

LED Color Description Panel

PSU Green Valid output. Power supply

Red Invalid output.

Blinking red Invalid input

GRWIC Green System is running. Power supply

Amber System is not running.

SYS Solid green Solid green indicates normal operation. Power supply

Blinking green System is booting or is in ROM monitor mode.

Amber System error.

Off Power is off or system board is faulty.

ACT Solid or blinking

green

Off No packet transfers are occurring.

RJ-45 CON Green Serial console is active. Cable side

USB CON Green USB console is active. Cable side

GE0/GE1: Link

SFP0 link/SFP1 link

SFP0 SPD/SFP1 SPD

CF0/CF1 Green Flash memory is being accessed; do not eject the

Green Solid green indicates the Ethernet port has a link

Off Not present. Power supply

Green Present and enabled.

Amber Present with failure.

Off No link. Cable side Green Note Blink indicates port speed.

blinking 2 blinks before pause – 100Mbps link speed.

Amber Compact flash error. Cable side

Off Flash memory is not being accessed; okay to eject

Solid or blinking indicates packet activity between the forwarding and routing engine and any I/O port.

partner.

3 blinks before pause – 1000Mbps link speed.

compact flash memory card.

the compact flash memory card.

side

side and cable side panel

Power supply side and cable side panel

Cable side

side

Cable side

Specifications

To view specifications for the 2010 CGR router, see the Cisco 2010 Connected Grid Router data sheet at:

http://www.cisco.com/en/US/prod/collateral/routers/ps10967/ps10977/data_sheet_c78_593509.html

Cisco Connected Grid Routers 2010 Hardware Installation Guide

1-8

OL-21559-01

CHA PTER

Preparing for Router Installation

This document provides preinstallation information, such as recommendations and requirements that should be met prior to installing your router. See the following sections to prepare for installation.

• Safety Recommendations, page 2-2

• General Site Requirements, page 2-4

• Rack Requirements, page 2-4

• Router Environmental Requirements, page 2-4

• Power Guidelines and Requirements, page 2-5

• Required Tools and Equipment for Installation and Maintenance, page 2-9

• Installation Checklist, page 2-10

• Creating a Site Log, page 2-10

Note To see translated warnings that appear in this publication, see the Cisco Connected Grid Routers Series

Regulatory Compliance and Safety Information document.

Warning

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement 1030

Ultimate disposal of this product should be handled according to all national laws and regulations.

Statement 1040

This equipment must be installed and maintained by service personnel as defined by AS/NZS 3260. Incorrectly connecting this equipment to a general-purpose outlet could be hazardous. The telecommunications lines must be disconnected 1) before unplugging the main power connector or 2) while the housing is open, or both.

This unit might have more than one power supply connection. All connections must be removed to de-energize the unit.

Statement 1028

Statement 1043

OL-21559-01

Cisco Connected Grid Routers 2010 Hardware Installation Guide

2-1

Safety Recommendations

Chapter 2 Preparing for Router Installation

Warning

This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: Maximum 15 A, 120 Vac or Maximum 10 A, 230 Vac

Statement 1005

Take care when connecting units to the supply circuit so that wiring is not overloaded.

Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables, detach the end away from the unit first.

Installation of the equipment must comply with local and national electrical codes.

This unit is intended for installation in restricted access areas. A restricted access area can be accessed only through the use of a special tool, lock and key, or other means of security.

Statement 1017

Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place.

Statement 1029

Statement 1026

Statement 1018

Statement 1074

Safety Recommendations

Follow these guidelines to ensure general safety:

• Keep the chassis area clear and dust-free during and after installation.

• Keep tools and chassis components away from walk areas.

• Do not wear loose clothing that could get caught in the chassis. Fasten your tie or scarf and roll up

your sleeves.

• Wear safety glasses when working under conditions that might be hazardous to your eyes.

• Do not perform any action that creates a hazard to people or makes the equipment unsafe.

Cisco Connected Grid Routers 2010 Hardware Installation Guide

2-2

OL-21559-01

Chapter 2 Preparing for Router Installation

Safety with Electricity

Follow these guidelines when working on equipment powered by electricity:

• Locate the emergency power-off switch in the room in which you are working. If an electrical

accident occurs, you can quickly turn off the power.

• Disconnect all power before doing the following:

–

Installing or removing a chassis

–

Working near power supplies

• Look carefully for possible hazards in your work area, such as moist floors, ungrounded power

extension cables, frayed power cords, and missing safety grounds.

• Do not work alone if hazardous conditions exist.

• Never assume that power is disconnected from a circuit. Always check.

• Never open the enclosure of the router’s internal power supply.

• If an electrical accident occurs, proceed as follows:

–

Use caution; do not become a victim yourself.

Safety Recommendations

–

Turn off power to the device.

–

If possible, send another person to get medical aid. Otherwise, assess the victim’s condition and then call for help.

–

Determine if the person needs rescue breathing or external cardiac compressions; then take appropriate action.

Warning

This unit might have more than one power supply connection. All connections must be removed to de-energize the unit.

Do not work on the system or connect or disconnect cables during periods of lightning activity.

Statement 1001

Read the installation instructions before connecting the system to the power source.

Statement 1028

Preventing Electrostatic Discharge Damage

Electrostatic discharge (ESD) can damage equipment and impair electrical circuitry. It can occur if electronic printed circuit cards are improperly handled and can cause complete or intermittent failures. Always follow ESD prevention procedures when removing and replacing modules:

• Ensure that the router chassis is electrically connected to earth ground.

Statement 1004

OL-21559-01

• Wear an ESD-preventive wrist strap, ensuring that it makes good skin contact. Connect the clip to

an unpainted surface of the chassis frame to channel unwanted ESD voltages safely to ground. To guard against ESD damage and shocks, the wrist strap and cord must operate effectively.

• If no wrist strap is available, ground yourself by touching a metal part of the chassis.

Cisco Connected Grid Routers 2010 Hardware Installation Guide

2-3

General Site Requirements

Caution For the safety of your equipment, periodically check the resistance value of the antistatic strap. It should

be between 1 and 10 megohms (Mohm).

General Site Requirements

This section describes the requirements your site must meet for safe installation and operation of your router. Ensure that the site is properly prepared before beginning installation. If you are experiencing shutdowns or unusually high errors with your existing equipment, this section can also help you isolate the cause of failures and prevent future problems.

Rack Requirements

The following information will help you plan your equipment rack configuration:

• Allow clearance around the rack for maintenance.

Chapter 2 Preparing for Router Installation

• Allow at least one rack unit of vertical space between routers.

• Enclosed racks must have adequate ventilation. Ensure that the rack is not congested, because each

router generates heat. An enclosed rack should have louvered sides and a fan to provide cooling air. Heat generated by equipment near the bottom of the rack can be drawn upward into the intake ports of the equipment above.

Router Environmental Requirements

Mount the Cisco 2010 CGR routers in a rack. The location of your router and the layout of your equipment rack or wiring room are extremely important considerations for proper operation. Equipment placed too close together, inadequate ventilation, and inaccessible panels can cause malfunctions and shutdowns, and can make maintenance difficult. Plan for access to both power supply side and cable side panels of the router.

Note Allow at least one rack unit of vertical space above the router.

When planning your site layout and equipment locations, refer to the “General Site Requirements”

section on page 2-4, section. If you are currently experiencing shutdowns or an unusually high number

of errors with your existing equipment, these precautions and recommendations may help you isolate the cause of failure and prevent future problems.

• Ensure that the room where your router operates has adequate air circulation. Electrical equipment

generates heat. Without adequate air circulation, ambient air temperature may not cool equipment to acceptable operating temperatures.

2-4

• Always follow ESD-prevention procedures described in the “Preventing Electrostatic Discharge

Damage” section on page 2-3 to avoid damage to equipment. Damage from static discharge can

cause immediate or intermittent equipment failure.

• Ensure that the chassis cover and module cable side panels are secure. All empty interface card slots

and power supply bays must have filler panels installed.

Cisco Connected Grid Routers 2010 Hardware Installation Guide

OL-21559-01

Chapter 2 Preparing for Router Installation

• When equipment installed in a rack (particularly in an enclosed rack) fails, try operating the

equipment by itself, if possible. Power off other equipment in the rack (and in adjacent racks) to allow the router under test a maximum of cooling air and clean power.

Power Guidelines and Requirements

Check the power at your site to ensure that you are receiving “clean” power (free of spikes and noise). Install a power conditioner if necessary.

The AC power supply includes the feature of autoselect for either 110 V or 220 V operation.

Caution Two types of power supplies are supported on the Cisco 2010 CGR: a low-voltage DC power supply and

a high-voltage DC/AC power supply. Take caution when selecting the correct input voltage for the power supply installed or damage will result.

For this release, only the high-voltage AC power supply is available.

Power Guidelines and Requirements

Network Cabling Specifications

The following sections describe the cables needed to install your Cisco 2010 CGR:

• Console and Auxiliary Port Considerations, page 2-5

• Preparing for Network Connections, page 2-7

Console and Auxiliary Port Considerations

The router includes an asynchronous serial console port and an auxiliary port. The console and auxiliary ports provide access to the router either locally using a console terminal connected to the console port, or remotely using a modem connected to the auxiliary port. This section discusses important cabling information to consider before connecting the router to a console terminal or modem.

The main difference between the console and auxiliary ports is that the auxiliary port supports hardware flow control and the console port does not. Flow control paces the transmission of data between a sending device and a receiving device. Flow control ensures that the receiving device can absorb the data sent to it before the sending device sends more. When the buffers on the receiving device are full, a message is sent to the sending device to suspend transmission until the data in the buffers has been processed. Because the auxiliary port supports flow control, it is ideally suited for use with the high-speed transmissions of a modem. Console terminals send data at slower speeds than modems; therefore, the console port is ideally suited for use with console terminals.

Console Port Connections

The router has both EIA/TIA-232 asynchronous (RJ-45) and USB 5-pin mini Type B, 2.0 compliant serial console ports. The console ports do not have any hardware flow control. Shielded USB cables with properly terminated shields are recommended.

OL-21559-01

Cisco Connected Grid Routers 2010 Hardware Installation Guide

2-5

Network Cabling Specifications

EIA/TIA-232

USB Serial Console

Note Always use shielded USB cables with a properly terminated shield.

Chapter 2 Preparing for Router Installation

Depending on the cable and the adapter used, this port appears as a DTE or DCE device at the end of the cable. Only one port can be used at the same time.

The default parameters for the console port are 9600 baud, 8 data bits, no parity, and 1 stop bit. The console port does not support hardware flow control. For detailed information about installing a console terminal, see the

For cable and port pinouts, see Cisco Modular Access Router Cable Specifications.

The USB serial console port connects directly to the USB connector of a PC using a USB Type A to 5-pin mini USB Type-B cable. The USB Console supports full speed (12Mb/s) operation. The console port does not support hardware flow control.

The default parameters for the console port are 9600 baud, 8 data bits, no parity, and 1 stop bit. The console port does not support mode control. For detailed information about installing a console terminal, see the

“Connecting to a Console Terminal or Modem” section on page 3-10.

For operation with Microsoft Windows, the Cisco Windows USB Console Driver must be installed on every PC connected to the console port. If the driver is not installed, prompts guide you through a simple installation process. For detailed information about installing the Cisco Windows USB Console Driver see

“Installing the Cisco Microsoft Windows USB Device Driver” section on page 3-13.

The Cisco Windows USB Console Driver allows plugging and unplugging the USB cable from the console port without affecting Windows HyperTerminal operations. No special drivers are needed for Mac OS X or Linux.

Only one console port can be active at a time. When a cable is plugged into the USB console port the RJ-45 port becomes inactive. Conversely, when the USB cable is removed from the USB port the RJ-45 port becomes active.

Baud rates for the USB console port are 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 bps.

Note 4-pin mini USB Type-B connectors are easily confused with 5-pin mini USB Type-B connectors.

They are not compatible. Only the 5-pin mini USB Type-B can be used.

Auxiliary Port Connections

The router has an EIA/TIA-232 asynchronous serial auxiliary port (RJ-45) that supports flow control. Depending on the cable and the adapter used, this port appears as a DTE or DCE device at the end of the cable.

2-6

Cisco Connected Grid Routers 2010 Hardware Installation Guide

OL-21559-01

Chapter 2 Preparing for Router Installation

Preparing for Network Connections

When setting up your router, consider distance limitations and potential electromagnetic interference (EMI) as defined by the applicable local and international regulations.

Network connection considerations are provided for several types of network interfaces and are described in the following sections:

• Ethernet Connections, page 2-7

• Serial Connections, page 2-7

See the following document for more information about network connections and interfaces:

• Cisco Modular Access Router Cable Specifications

Network Cabling Specifications

Warning

To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some LAN and WAN ports both use RJ-45 connectors.

Ethernet Connections

The IEEE has established Ethernet as standard IEEE 802.3. Cisco 2010 CGR support the following Ethernet implementations:

• 1000BASE-X—1000 Mb/s full-duplex transmission over a Category 5 or better unshielded

• 1000BASE-T—1000 Mb/s full-duplex transmission over a Category 5 or better unshielded

• 100BASE-TX—100 Mb/s full-duplex transmission over a Category 5 or better unshielded

See Cisco Modular Access Router Cable Specifications at www.cisco.com for information about Ethernet cables, connectors, and pinouts.

Serial Connections

Statement 1021

twisted-pair (UTP) cable (IEEE 802.3z). Supports the Ethernet maximum length of 328 meters).

twisted-pair (UTP) cable (IEEE 802.3ab). Supports the Ethernet maximum length of 328 meters).

twisted-pair (UTP) cable (IEEE 802.3u). Supports the Ethernet maximum length of 328 meters).

feet (100

Serial connections are provided by the grid router WAN interface card (GRWIC). Before you connect a device to a serial port, you need to know the following:

• Type of device, data terminal equipment (DTE) or data communications equipment (DCE), you are

connecting to the synchronous serial interface

• Type of connector, male or female, required to connect to the device

• Signaling standard required by the device

Configuring Serial Connections

The serial ports on the asynchronous/synchronous serial network modules and the serial grid router WAN interface card use an GRWIC-8A/S cable with a DB-25 connector. Serial ports can be configured as DTE or DCE, depending on the serial cable used.

OL-21559-01

Cisco Connected Grid Routers 2010 Hardware Installation Guide

2-7

Network Cabling Specifications

Serial DTE or DCE Devices

A device that communicates over a synchronous serial interface is either a DCE or DTE device. A DCE device provides a clock signal that paces the communications between the device and the router. A DTE device does not provide a clock signal. DTE devices usually connect to DCE devices. The documentation that accompanied the device should indicate whether it is a DTE or DCE device. (Some devices have a jumper to select either DTE or DCE mode.)

Ta b l e 2-1 Typical DTE and DCE Devices

Device Type Gender Typical Devices

DTE Male

DCE Female

1. If pins protrude from the base of the connector, the connector is male.

2. If the connector has holes to accept pins, the connector is female.

Chapter 2 Preparing for Router Installation

Table 2-1 lists typical DTE and DCE devices.

Termin a l

Modem

CSU/DSU

Multiplexer

Signaling Standards Supported

The synchronous serial ports available for the router support the following signaling standards: EIA/TIA-232 (EIA-323). You can order a Cisco DB-25 shielded serial transition cable that has the appropriate connector for the standard you specify. The documentation for the device should indicate the standard used for that device. The router end of the shielded serial transition cable has a DB-25 connector, which connects to the DB-25 port on a serial of the serial transition cable is available with a connector appropriate for the standard you specify.

The synchronous serial port can be configured as DTE or DCE, depending on the attached cable.

All serial ports configured as DTE require external clocking from a CSU/DSU or other DCE device.

Distance Limitations

Serial signals can travel a limited distance at any given bit rate; generally, the slower the data rate, the greater the distance. All serial signals are subject to distance limits, beyond which a signal significantly degrades or is completely lost.

Table 2-2 lists the recommended maximum speeds and distances for each serial interface type; however,

you might get good results at speeds and distances greater than those listed, if you understand the electrical problems that might arise and can compensate for them. For instance, the recommended maximum rate for V.35 is 2

Ta b l e 2-2 Serial Signal Transmission Speeds and Distances

Rate (bps) Feet Meters Feet Meters Feet Meters

2400 200 60 4100 1250 16.4 5

4800 100 30 2050 625 16.4 5

9600 50 15 1025 312 16.4 5

Mb/s, but 4 Mb/s is commonly used.

Distance for EIA/TIA-232

grid router WAN interface card. The other end

Distance for X.21 and V. 35

Distance for USB

2-8

Cisco Connected Grid Routers 2010 Hardware Installation Guide

OL-21559-01

Chapter 2 Preparing for Router Installation

Table 2-2 Serial Signal Transmission Speeds and Distances (continued)

Required Tools and Equipment for Installation and Maintenance

Distance for EIA/TIA-232

Distance for X.21 and V.35 Distance for USB

Rate (bps) Feet Meters Feet Meters Feet Meters

19200 25 7.6 513 156 16.4 5

38400 12 3.7 256 78 16.4 5

56000 8.6 2.6 102 31 16.4 5

1544000 (T1) — — 50 15 16.4 5

Asynchronous/Synchronous Serial Module Baud Rates

The following baud-rate limitations apply to the slow-speed serial interfaces found in the asynchronous/synchronous serial modules:

• Asynchronous interface—Maximum baud rate is 115.2 kbps.

• Synchronous interface—Maximum baud rate is 128 kbps full duplex.

Required Tools and Equipment for Installation and Maintenance

You need the following tools and equipment to install and upgrade the router and its components:

• ESD-preventive cord and wrist strap

• Number 2 Phillips screwdriver

• Phillips screwdrivers: small, 3/16-in. (4 to 5 mm) and medium, 1/4-in. (6 to 7 mm)

• Screws that fit your rack

In addition, depending on the type of modules you plan to use, you might need the following equipment to connect a port to an external network:

• Cables for connection to the WAN and LAN ports (dependent on configuration).

Note For more information on cable specifications, see Cisco Modular Access Router Cable

Specifications at www.cisco.com.

• Ethernet hub or PC with a network interface card for connection to an Ethernet (LAN) port.

• Console terminal (an ASCII terminal or a PC running HyperTerminal or similar terminal emulation

software) configured for 9600 baud, 8 data bits, 1 stop bit, no flow control, and no parity.

• Modem for connection to the auxiliary port for remote administrative access (optional).

• Data service unit (DSU) or channel service unit/data service unit (CSU/DSU) as appropriate for

serial interfaces.

• External CSU for any CT1/PRI modules without a built-in CSU.

OL-21559-01

Cisco Connected Grid Routers 2010 Hardware Installation Guide

2-9

Installation Checklist

The sample installation checklist lists items and procedures for installing a new router. Make a copy of this checklist and mark the entries when completed. Include a copy of the checklist for each router in your site log (described in

Installation checklist for site_____________________________________________

Router name_______________________________________________________

Tas k Verified by Date

Installation checklist copied

Background information placed in Site Log

Site power voltages verified

Installation site power check completed

Required tools available

Additional equipment available

Router received

Product registration card received

www.cisco.com contact information label received

Chassis components verified

Initial electrical connections established

ASCII terminal (for local configuration) or modem

Signal distance limits verified

Startup sequence steps completed

Initial operation verified

Software image verified

(for remote configuration) available

Chapter 2 Preparing for Router Installation

“Creating a Site Log” section on page 2-10).

Creating a Site Log

The Site Log provides a record of all actions related to the router. Keep it in an accessible place near the chassis where anyone who performs tasks has access to it. Use the installation checklist to verify steps in the installation and maintenance of the router. Site Log entries might include the following information:

• Installation progress—Make a copy of the installation checklist and insert it into the site log. Make

entries as each procedure is completed.

• Upgrade and maintenance procedures—Use the site log as a record of ongoing router maintenance

and expansion history. A site log might include the following events:

–

Installation of GRWICs

–

Removal or replacement of GRWICs and other upgrades

–

Configuration changes

Cisco Connected Grid Routers 2010 Hardware Installation Guide

2-10

OL-21559-01

Chapter 2 Preparing for Router Installation

–

Maintenance schedules and requirements

–

Maintenance procedures performed

–

Intermittent problems

–

Comments and notes

Inspect all items for shipping damage. If anything appears to be damaged or you encounter problems installing or configuring your router, contact Cisco customer service. Warranty, service, and support information is in the quick start guide that shipped with your router.

Creating a Site Log

OL-21559-01

Cisco Connected Grid Routers 2010 Hardware Installation Guide

2-11

Creating a Site Log

Chapter 2 Preparing for Router Installation

2-12

Cisco Connected Grid Routers 2010 Hardware Installation Guide

OL-21559-01

CHA PTER

Installing and Connecting the Router

This document describes how to install and connect Cisco Connected Grid Routers (CGR) 2010 to a LAN or WAN. The following sections provide technical details.

• What you Need to Know, page 3-3

• Before You Begin, page 3-4

• Unpacking the Router, page 3-4

• Installing the Router in a Rack, page 3-4

• Connecting Power, page 3-7

• Connecting to a Console Terminal or Modem, page 3-10

• Installing the Cisco Microsoft Windows USB Device Driver, page 3-13

• Uninstalling the Cisco Microsoft Windows USB Driver, page 3-15

• Connecting to the Auxiliary Port, page 3-16

• Connecting WAN and LAN Interfaces, page 3-17

Note To see translations of the warnings that appear in this publication, see Cisco Connected Grid Routers

Series Regulatory Compliance and Safety Information.

Caution For the optimum temperature ranges, do not operate it in an area that less than the minimum of 40°C and

exceeds a maximum recommended ambient temperature of 60°C.

Note To view specifications for the 2010 CGR router, see the Cisco 2010 Connected Grid Router data sheet at:

http://www.cisco.com/en/US/prod/collateral/routers/ps10967/ps10977/data_sheet_c78_593509.html

Warning

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement 1030

OL-21559-01

Cisco Connected Grid Routers 2010 Hardware Installation Guide

3-1

Chapter 3 Installing and Connecting the Router

REVIEW DRAFT—CISCO CONFIDENTIAL

Warning

This unit might have more than one power supply connection. All connections must be removed to de-energize the unit.

Statement 1028

Statement 1026

Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool.

Statement 1035

Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.

Statement 1038

This unit is intended for installation in restricted access areas. A restricted access area can be accessed only through the use of a special tool, lock and key, or other means of security.

Statement 1017

Warning

Stability hazard. The rack stabilizing mechanism must be in place, or the rack must be bolted to the floor before you slide the unit out for servicing. Failure to stabilize the rack can cause the rack to tip over.

Statement 1048

The chassis should be mounted on a rack that is permanently affixed to the building.

Statement 1049

Statement 1029

A ground wire must always be a single piece of wire. Never splice two wires together for a ground. Corrosion and weathering can lead to a poor connection at the splice, making the ground ineffective and dangerous.

To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord.

Statement 270

Statement 1023

3-2

Warning

Cisco Connected Grid Routers 2010 Hardware Installation Guide

Use copper conductors only.

Statement 1025

OL-21559-01

Chapter 3 Installing and Connecting the Router

REVIEW DRAFT—CISCO CONFIDENTIAL

What you Need to Know

Warning

Caution Heat sinks applicable to warning statement 1079, can exceed 90 C in a 65 C ambient. Suitable

A readily accessible two-poled disconnect device must be incorporated in the fixed wiring.

1022

Invisible laser radiation may be emitted from the end of the unterminated fiber cable or connector. Do not view directly with optical instruments. Viewing the laser output with certain optical instruments (for example, eye loupes, magnifiers, and microscopes) within a distance of 100 mm may pose an eye hazard.

To prevent the system from overheating, do not operate it in an area that exceeds the maximum recommended ambient temperature of: 65°C (149°F).

Hot surface.

Statement 1056

Statement 1047

Statement 1079

precautions should be taken to avoid burns.

Warning

This equipment needs to be grounded. Use a green and yellow 12 to 14 AWG ground wire to connect the host to earth ground during normal use.

Statement 242

Statement

What you Need to Know

CLI Console Access

Use the new USB console port on the router to access the Cisco Internet Operating System (IOS) Command Line Interface (CLI) on the router and perform configuration tasks. A terminal emulation program, such as Microsoft Windows HyperTerminal, is required to establish communication between the router and a PC. See the instructions.

Note A Microsoft Windows USB driver must be installed before you establish physical connectivity

between the router and the PC.

Slot and Port Numbers

Cisco 2010 CGR have built in ports and new slots. The new slots accommodate new grid

router WA N interface cards (GRWICs). See the “Slot, Port, and Interface Information” section on

page 1-6 for slot and port numbering.

“Connecting to a Console Terminal or Modem” section on page 3-10 for

OL-21559-01

Cisco Connected Grid Routers 2010 Hardware Installation Guide

3-3

Before You Begin

REVIEW DRAFT—CISCO CONFIDENTIAL

Before You Begin

Before installing and connecting a Cisco 2010 CGR router, read the safety warnings and gather the following tools and equipment:

• ESD-preventive cord and wrist strap

• Number 2 Phillips screwdriver

• Flat-blade screwdrivers: small, 3/16-in. (4 to 5 mm) and medium, 1/4-in. (6 to 7 mm)

–

To install or remove GRWICs

–

To remove the cover, if you are upgrading memory or other components

• Screws that fit your rack

In addition, depending on the type of modules you plan to use, you might need the following equipment to connect a port to an external network:

• Cables for connection to the WAN and LAN ports (dependent on configuration).

Note For more information on cable specifications, see Cisco Modular Access Router Cable

Chapter 3 Installing and Connecting the Router

Specifications on www.cisco.com.

• Ethernet hub or PC with a network interface card for connection to an Ethernet (LAN) port.

• Console terminal (an ASCII terminal or a PC running HyperTerminal or similar terminal emulation

software) configured for 9600 baud, 8 data bits, 1 stop bit, no flow control, and no parity.

• Modem for connection to the auxiliary port for remote administrative access (optional).

• Data service unit (DSU) or channel service unit/data service unit (CSU/DSU) as appropriate for

serial interfaces.

• External CSU for any CT1/PRI modules without a built-in CSU.

• NT1 device for ISDN BRI S/T interfaces (if not supplied by your service provider).

Caution Sites with ambient temperatures consistently above 25 degrees C (77 degrees F) and with potentially

high levels of dust or debris may require periodic preventative maintenance cleaning.

Unpacking the Router

Do not unpack the router until you are ready to install it. If the final installation site will not be ready for some time, keep the chassis in its shipping container to prevent accidental damage. When you are ready to install the router, proceed with unpacking it.

The router, accessory kit, publications, and any optional equipment you ordered may be shipped in more than one container. When you unpack the containers, check the packing list to ensure that you received all of the items on the list.

Installing the Router in a Rack

The Cisco 2010 CGR can only be mounted in a rack.

Cisco Connected Grid Routers 2010 Hardware Installation Guide

3-4

OL-21559-01

Chapter 3 Installing and Connecting the Router

REVIEW DRAFT—CISCO CONFIDENTIAL

Caution To prevent damage to the chassis, never attempt to lift or tilt the chassis by holding it by the plastic panel

on the front. Always hold the chassis by the sides of the metal body.

Note Allow at least one rack unit of vertical space above the router.

Rack-Mounting the Chassis

Cisco 2010 CGR can be installed in 19-inch (48.26-cm) standard rack.

You can mount the router in the following ways:

• Power supply side mounting—Brackets attached at the power supply side of the chassis with the

power supply side facing forward.

• Cable side mounting—Brackets attached at the cable side of the chassis with the cable side facing

forward.

Figure 3-2 shows the rack-mount brackets used with the Cisco 2010 CGR.

Installing the Router in a Rack

Figure 3-1 Rack-Mount Brackets for the Cisco 2010 CGR

249218

Attaching Rack-Mount Brackets to Cisco 2010 CGR Routers

For the Cisco 2010 CGR routers, use four of the supplied number-8 Phillips flat-head screws to attach the long side of each bracket to the router.

Figure 3-2 shows how to attach the brackets to the sides of the router with the power supply side forward.

OL-21559-01

Cisco Connected Grid Routers 2010 Hardware Installation Guide

3-5

Installing the Router in a Rack

REVIEW DRAFT—CISCO CONFIDENTIAL

Figure 3-2 Bracket Installation for Power Supply Side Mounting

Figure 3-3 shows how to attach the brackets to the sides of the router with the cable side forward.

Figure 3-3 Bracket Installation for Cable Side Mounting

PWR-150W-HV

PSU OK

PSU1 PSU2

SFP

0/1

CAUTION: This unit may have more than one power source. Disconnect all power sources before servicing to avoid electric shock.

ACT

SYS

0/0

SPD SPD

SLOT

0/1

0/0

LINK

SPD SPD 2 0 1

USB

PSU

CON

231

CONSOLE

Chapter 3 Installing and Connecting the Router

PWR-150W-HV

PSU OK

CF1

DO NOT REMOVE DURING

CF0

NETWORK OPERATION

DO NOT REMOVE DURING

NETWORK OPERATION

Input Terminal

Type

Input Rating

Symbol

Lo V DC

Per Source

Hi V DC

24 - 60 V 10A

100-250V 2A

V AC

100-240V

50-60 Hz

Cisco Connected Grid Router 2000 Series

277568

Caution Do not over torque the screws. The recommended torque is 15 to 18 inch-lb (1.7 to 2.0 N-m).

Attach the second bracket to the opposite side of the chassis. Use a number 2 Phillips screwdriver to install the number-8 bracket screws.

Caution Your chassis installation must allow unrestricted airflow for chassis cooling.

Mounting the Router in a Rack

After you attach the rack-mount brackets to the router chassis, use the screws provided with the rack to install the chassis in the rack. (See

Cisco CGR 2010

PSU2PSU1

- Lo +

ACT

SFP 0/0

SFP 0/1

SPD

SYS 0

SLOT 3 SLOT 2

GE 0/1

AUX

GE 0/0

CONSOLE

SLOT 1 SLOT 0

CONN CONN

0-3

4-7

CD/LP AL CD/LP AL

P1 P0

277447

Figure 3-4.)

3-6

Tip The screw slots in the brackets are spaced to line up with every second pair of screw holes in the rack.

When the correct screw holes are used, the small threaded holes in the brackets line up with unused screw holes in the rack. If the small holes do not line up with the rack holes, you must raise or lower the brackets to the next rack hole.

Caution A space of 1 RU above each Cisco 2010 CGR is required for sufficient air ventilation.

Cisco Connected Grid Routers 2010 Hardware Installation Guide

OL-21559-01

Chapter 3 Installing and Connecting the Router

REVIEW DRAFT—CISCO CONFIDENTIAL

Figure 3-4 shows a typical installation in a rack.

Figure 3-4 Mounting the Chassis in a Rack (Typical)

Cisco CGR 2010

PSU2PSU1

+ Lo

- Lo +

1 Mounting screws (4)

Connecting Power

SLOT 3 SLOT 2

GE 0/1

AUX

ACT

SFP 0/0

SFP 0/1

SPD

SYS 0

GE 0/0

CONSOLE

SLOT 1 SLOT 0

CONN CONN

0-3

4-7

CD/LP AL CD/LP AL

P1 P0

277448

Connecting Power

This section explains how to connect AC or DC power to Cisco 2010 CGR.

Warning

Connecting Power

Step 1 Verify that power is off to the circuit on the power supply that you are removing. As an added precaution,

Step 2 Slide the cable input wires into the terminal holes marked below. See Figure 3-5.

Read the installation instructions before connecting the system to the power source.

To connect a power supply, follow these steps:

place the appropriate safety flag and lockout devices at the source power circuit breaker, or place a piece of adhesive tape over the circuit breaker handle to prevent accidental power restoration while you are working on the circuit.

a. Place the black or brown lead of the cable into the terminal marked L. b. Place the white or blue lead of the cable into the terminal marked N. This terminal is immediately

adjacent to the above L terminal.

c. Place the green or green/yellow lead of the cable into the terminal marked with the ground symbol.

Figure 1-3 shows the ground symbol.

Statement 1004

OL-21559-01

d. Use a tie wrap to secure the cable to the strain relief mechanissm that are next to the terminal block

on the chassis. Secure the cable immediately adjacent to the terminal block to minimize strain on the cable.

Cisco Connected Grid Routers 2010 Hardware Installation Guide

3-7

Connecting Power

PSU2

PSU1

Caution Ensure that all strands of a stranded wire are properly captured into the terminal block. A loose strand

Chapter 3 Installing and Connecting the Router

REVIEW DRAFT—CISCO CONFIDENTIAL

Note The strain relief mechanism are three metal loops built into the chassis next to the terminal

block.

e. Use minimum 14 AWG or maximum 12 AWG copper wire to connect the router to a 15 A branch

circuit in accordance with local electrical code requirements. Verify that the voltage at the router is within the rated operating voltage range of the product.

could possibly short the chassis and result in a hazard.

Warning

When installing or replacing the unit, the ground connection must always be made first and disconnected last.

Statement 1046

Figure 3-5 Connecting Power Using the Terminal Block

Cisco CGR 2010

PSU2

PSU1

SFP 0/0

SPD

GE 0/1

AUX

CF1PS

2ACT

SYS 0 1

SFP 0/1

CONSOLE

GE 0/0

SLOT 3 SLOT 2 SLOT 1 SLOT 0

CONN CONN

0-3

GRWIC–8A/8-232

P1 P0

4-7

GRWIC–2CE1T1-PRI

CD/LP AL CD/LP AL

277569

Step 3 Fully insert the un-insulated lead in to the terminal block and screw each captive screw on the terminal

block tight to ensure proper connection.

Step 4 Use a tie wrap to secure the cable to the strain relief mechanism that is new to the terminal block on the

chassis. Secure the cable immediately adjacent to the terminal block to minimize strain on the cable. See

Figure 3-6.

3-8

Cisco Connected Grid Routers 2010 Hardware Installation Guide

OL-21559-01

Chapter 3 Installing and Connecting the Router

REVIEW DRAFT—CISCO CONFIDENTIAL

Figure 3-6 Using Tie Wraps with Strain Relief Mechanism

Cisco CGR 2010

PSU2PSU1

+ Lo

- Lo +

1 Tie wraps to strain relief mechanism

GE 0/1

ACT

SFP 0/0

SFP 0/1

SPD

SYS 0

GE 0/0

Connecting Power

SLOT 3 SLOT 2

AUX

CONSOLE

SLOT 1 SLOT 0

CONN CONN

0-3

4-7

CD/LP AL CD/LP AL

P1 P0

199587

Caution The AWG size of the wires feeding power to the input terminal block is a minimum of 14 AWG (2.0

) or a maximum of 12 AWG (3.309 mm2), all for a 15 Amp branch circuit. 12 AWG is the largest

wire that the terminal block will accept.

Caution Do not overtorque the terminal block contact screws. Recommended torque is 8.0 ± 0.5 in-lb

(0.9 ± 0.05 N-m).

Caution Strain on the cable could dislodge the leads from the terminal block.

Caution Do not use a power cable to connect the chassis low voltage DC input to a voltage source. If you

inadvertently plug a cable into a 120 Vac source, the low voltage supply will be damaged and hazard could result.

If you need a cable to connect to the low voltage DC power supply, cut off the plug from the power cord and hard wire the Cisco 2010 CGR low voltage DC input directly to its power source, observing the correct polarity markings.

Caution Stay clear of the terminal block when energy has been restored. The terminal block screw heads and any

exposed wiring could have hazardous line voltages (depending on the voltage source). The Cisco 2010 CGR is intended to be installed in a restricted access location and serviced by trained personnel only.

Shutting Off Power

Even though shutting off power to the Cisco 2010 CGR is anticipated to be infrequent, there may be occasion to turn off the router. There is no on/off switch on the Cisco 2010 CGR. This ensures that there will not be any accidental shutdown due to turning off a power switch; thus, guaranteeing a high reliability in keeping the router up. To shut off power to the router, there are two options:

• Pull the power supply modules out of the Cisco 2010 CGR router.

OL-21559-01

Cisco Connected Grid Routers 2010 Hardware Installation Guide

3-9

Chapter 3 Installing and Connecting the Router

Connecting to a Console Terminal or Modem

REVIEW DRAFT—CISCO CONFIDENTIAL

The power supplies on the Cisco 2010 CGR router are hot swappable, so merely removing them from the router will remove power from the router and shut it down.

• Install a disconnect device for the Cisco 2010 CGR router.

A disconnect device must be located in the proximity of the Cisco 2010 CGR router and must be readily accessible. The disconnect device must also comply with IEC 60947-1 and IEC 60947-3 or an equivalent approved disconnect device appropriate for the country of installation and be identified as the disconnect device for this equipment.

Note The maximum current rating for the power disconnect circuit breaker or overcurrent device must

be 15 Amps. Operational power must be internally fused. This fuse cannot be replaced by the user. In the event of the disconnect device failing, return the unit to the factory for repair.

Connecting to a Console Terminal or Modem

The router has asynchronous serial ports and auxiliary ports. These ports provide administrative access to the router either locally (with a console terminal or a PC) or remotely (with a modem). To configure the router through the Cisco between the router console port and either a terminal or a PC.

Table 3-1 shows cables and adapters to establish a local or remote connection.

IOS command-line interface (CLI), you must establish a connection

Ta b l e 3-1 Local and Remote Connections

Port Type Cable Section

Serial (RJ-45) EIA RJ-45 Connecting to the Serial Port with

Serial (USB) USB 5-pin mini USB Type-B-to-USB

Type-A

Auxiliary (Modem) DB-9-to-DB-25 Connecting to the Auxiliary Port

Connecting to the Serial Port with Microsoft Windows

This section describes using Microsoft Windows to connect to the serial port.

Note Install the USB device driver before establishing a physical connection between the router and the PC

using the USB Console cable plugged into the USB serial port, otherwise the connection will fail. See the “Installing the Cisco Microsoft Windows USB Device Driver” section on page 3-13.

Step 1 Connect the end of the console cable with the RJ-45 connector to the light blue console port on the router.

Connect a USB 5-pin mini USB Type-B to the USB console port, as shown in Figure 3-7. If you are using the USB serial port for the first time on a Windows-based PC, install the USB driver now according to the instructions in the following sections.

• Installing the Cisco Microsoft Windows XP USB Driver

Microsoft Windows

3-10

Cisco Connected Grid Routers 2010 Hardware Installation Guide

OL-21559-01

Chapter 3 Installing and Connecting the Router

REVIEW DRAFT—CISCO CONFIDENTIAL

• Installing the Cisco Microsoft Windows 2000 USB Driver

• Installing the Cisco Microsoft Windows Vista USB Driver

Note You cannot use the USB port and the EIA port concurrently. See the “Connecting to the

Auxiliary Port” section on page 3-16. When the USB port is used, it takes priority over the RJ-45

EIA port.

Step 2 Connect the end of the cable with the DB-9 connector (or USB Type-A) to the terminal or PC. If your

terminal or PC has a console port that does not accommodate a DB-9 connector, you must provide an appropriate adapter for that port.

Note To identify the COM port assigned to the USB console port, use the Control Panel to open the Device

Manager, and expand the Ports section. The assigned COM port is shown in parenthesis at the end of the line with the following entry: Cisco USB System Management Console.

Step 3 To communicate with the router, start a terminal emulator application, such as Microsoft Windows

HyperTerminal. This software should be configured with the following parameters:

• 9600 baud

Connecting to a Console Terminal or Modem

• 8 data bits

• no parity

• 1 stop bit

• no flow control

OL-21559-01

Cisco Connected Grid Routers 2010 Hardware Installation Guide

3-11

Connecting to a Console Terminal or Modem

REVIEW DRAFT—CISCO CONFIDENTIAL

Figure 3-7 Connecting the USB Console Cable to the Cisco 2010 CGR

Cisco CGR 2010

PSU2PSU1

+ Lo

- Lo +

SFP 0/0

SFP 0/1

SPD

Chapter 3 Installing and Connecting the Router

SLOT 3 SLOT 2

SLOT 1 SLOT 0

GE 0/1

AUX

ACT

SYS

GE 0/0

CONSOLE

CONN CONN

0-3

CD/LP AL CD/LP AL

P1 P0

4-7

1 USB 5-pin mini USB type-B console port 2 USB 5-pin mini USB type-B to USB type-A

3 USB Type-A

Connecting to the Console Port with Mac OS X

This procedure describes how to connect a Mac OS X system USB port to the console using the built in OS

X Terminal utility.

console cable

277570

3-12

Step 1 Use the Finder to go to Applications > Utilities > Ter mi nal . Step 2 Connect the OS X USB port to the router. Step 3 Enter the following commands to find the OS X USB port number:

Cisco Connected Grid Routers 2010 Hardware Installation Guide

OL-21559-01

Chapter 3 Installing and Connecting the Router

REVIEW DRAFT—CISCO CONFIDENTIAL

macbook:user$ cd /dev macbook:user$ ls -ltr /dev/*usb* crw-rw-rw- 1 root wheel 9, 66 Apr 1 16:46 tty.usbmodem1a21 DT-macbook:dev user$

Step 4 Connect to the USB port with the following command followed by the router USB port speed

macbook:user$ screen /dev/tty.usbmodem1a21 9600

To disconnect the OS X USB console from the Terminal window

Enter Ctrl-A followed by Ctrl-\

Connecting to the Console Port with Linux

This procedure shows how to connect a Linux system USB port to the console using the built in Linux Terminal utility.

Step 1 Open the Linux Terminal window.

Installing the Cisco Microsoft Windows USB Device Driver

Step 2 Connect the Linux USB port to the router. Step 3 Enter the following commands to find the Linux USB port number:

root@usb-suse# cd /dev root@usb-suse /dev# ls -ltr *ACM* crw-r--r-- 1 root root 188, 0 Jan 14 18:02 ttyACM0 root@usb-suse /dev#

Step 4 Connect to the USB port with the following command followed by the router USB port speed:

root@usb-suse /dev# screen /dev/ttyACM0 9600

To disconnect the Linux USB console from the Terminal window

Enter Ctrl-A followed by :, then type quit

Installing the Cisco Microsoft Windows USB Device Driver

A USB device driver must be installed the first time a Microsoft Windows-based PC is connected to the USB serial port on the router.

This section contains the following topics:

• Installing the Cisco Microsoft Windows XP USB Driver

• Installing the Cisco Microsoft Windows 2000 USB Driver

• Installing the Cisco Microsoft Windows Vista USB Driver

Installing the Cisco Microsoft Windows XP USB Driver

This procedure shows how to install the Microsoft Windows XP USB driver.

Cisco Connected Grid Routers 2010 Hardware Installation Guide

OL-21559-01

3-13

Chapter 3 Installing and Connecting the Router

Installing the Cisco Microsoft Windows USB Device Driver

REVIEW DRAFT—CISCO CONFIDENTIAL

Step 1 Obtain the file Cisco_usbconsole_driver.zip from www.cisco.com website and unzip it. Step 2 If using 32-bit Windows XP, double-click the file setup.exe from the Windows_32 folder. If using 64-bit

Windows XP, double-click the file setup(x64).exe from the Windows_64 folder.

Step 3 The Cisco Virtual Com InstallShield Wizard begins. Click Next. Step 4 The Ready to Install the Program window appears. Click Install. Step 5 The InstallShield Wizard Completed window appears. Click Finish. Step 6 Connect the USB cable to the PC and router USB console ports (see Tabl e 3-1). The EN LED for the

USB console port turns green, and within a few moments the Found New Hardware wizard appears. Follow the instructions to complete the installation of the driver.

Step 7 The USB console is ready for use.

Installing the Cisco Microsoft Windows 2000 USB Driver

This procedure shows how to install the Microsoft Windows 2000 USB driver.

Step 1 Obtain the file Cisco_usbconsole_driver.zip from www.cisco.com and unzip it. Step 2 Double-click the file setup.exe. Step 3 The Cisco Virtual Com InstallShield Wizard begins. Click Next. Step 4 The Ready to Install the Program window appears, Click Install. Step 5 The InstallShield Wizard Completed window appears. Click Finish. Step 6 Connect the USB cable to the PC and router USB console ports (see Tabl e 3-1). The EN LED for the

USB console port turns green, and within a few moments a series of Found New Hardware wizard windows appear. Follow the instructions to complete the installation of the driver.

Step 7 The USB console is ready for use.

Installing the Cisco Microsoft Windows Vista USB Driver

This procedure shows how to install the Microsoft Windows Vista USB driver.

Step 1 Obtain the file Cisco_usbconsole_driver.zip from www.cisco.com and unzip it. Step 2 If using 32-bit Windows Vista, double-click the file setup.exe from the Windows_32 folder, or if using

64-bit Windows Vista, double-click the file setup(x64).exe from the Windows_64 folder.

Step 3 The Cisco Virtual Com InstallShield Wizard begins. Click Next.

3-14

Step 4 The Ready to Install the Program window appears, Click Install.

Note If a User Account Control warning appears, click “Allow - I trust this program...” to proceed.

Step 5 The InstallShield Wizard Completed window appears. Click Finish.

Cisco Connected Grid Routers 2010 Hardware Installation Guide

OL-21559-01

Chapter 3 Installing and Connecting the Router

Uninstalling the Cisco Microsoft Windows USB Driver

REVIEW DRAFT—CISCO CONFIDENTIAL

Step 6 Connect the USB cable to the PC and router USB console ports (See Tabl e 3-1). The EN LED for the

USB console port turns green, and within a few moments a pop up window stating “Installing device driver software” appears. Following the instructions to complete the installation of the driver.

Step 7 The USB console is ready for use.

Uninstalling the Cisco Microsoft Windows USB Driver

This section provides instructions for how to uninstall the Cisco Microsoft Windows USB device driver.

• Uninstalling the Cisco Microsoft Windows XP and 2000 USB Driver

• Uninstalling the Cisco Microsoft Windows Vista USB Driver

Uninstalling the Cisco Microsoft Windows XP and 2000 USB Driver

This procedure shows you how to uninstall both the Microsoft Windows XP and 2000 USB driver. The driver can be removed using the Windows Add or Remove Programs utility or the setup.exe program.

Using the Add Remove Programs utility

Note Disconnect the router console terminal before uninstalling the driver.

Step 1 Click Start > Control Panel > Add or Remove Programs. Step 2 Scroll to Cisco Virtual Com and click Remove. Step 3 When the Program Maintenance window appears, select the Remove radio button. Click Next.

Using the Setup.exe program

Note Disconnect the router console terminal before uninstalling the driver.

Step 1 Run the setup.exe for Windows 32-bit or setup(x64).exe for Windows-64bit. Click Next. Step 2 The InstallShield Wizard for Cisco Virtual Com appears. Click Next. Step 3 When the Program Maintenance window appears, select the Remove radio button. Click Next. Step 4 When the Remove the Program window appears, click Remove. Step 5 When the InstallShield Wizard Completed window appears, click Finish.

Uninstalling the Cisco Microsoft Windows Vista USB Driver

This procedure shows you how to uninstall the Microsoft Windows Vista USB driver.

Cisco Connected Grid Routers 2010 Hardware Installation Guide

OL-21559-01

3-15

Connecting to the Auxiliary Port

CONSOLE

AUX

REVIEW DRAFT—CISCO CONFIDENTIAL

Note Disconnect the router console terminal before uninstalling the driver.

Note If a User Account Control warning appears, click “Allow - I trust this program...” to proceed.

Step 5 When the InstallShield Wizard Completed window appears, click Finish.

Connecting to the Auxiliary Port

Chapter 3 Installing and Connecting the Router

When a modem is connected to the auxiliary port, a remote user can dial in to the router and configure it.

To connect a modem to the router, follow these steps:

Step 1 Connect the RJ-45 end of the adapter cable to the black AUX port on the router. (See Figure 3-8.)

Figure 3-8 Connecting a Modem to the Cisco 2010 CGR

Cisco CGR 2010

PSU2PSU1

GE 0/1

ACT

SFP 0/0

SFP 0/1

SPD

SYS

GE 0/0

SLOT 3

SLOT 2

AUX

CONSOLE

SLOT 1

CONN CONN

0-3

SLOT 0

CD/LP AL CD/LP AL

P1 P0

4-7

3-16

277571

Cisco Connected Grid Routers 2010 Hardware Installation Guide

OL-21559-01

Chapter 3 Installing and Connecting the Router

REVIEW DRAFT—CISCO CONFIDENTIAL

1 RJ-45 AUX port 2 DB-9 to DB-25 adapter

3 RJ-45 to DB-9 4 Modem

Step 2 Connect the DB-9 end of the console cable to the DB-9 end of the modem adapter. Step 3 Connect the DB-25 end of the modem adapter to the modem. Step 4 Make sure that your modem and the router auxiliary port are configured for the same transmission speed

(up to 115200 bps is supported) and for mode control with data carrier detect (DCD) and data terminal ready (DTR) operations.

Connecting WAN and LAN Interfaces

This section describes how to connect WAN and LAN interface cables.

Note One or two Ethernet cables are typically provided with the router. Additional cables and transceivers can

be ordered from Cisco. For ordering information, contact customer service. For cable pinouts, see

Modular Access Router Cable Specifications.

Connecting WAN and LAN Interfaces

Cisco

Warning

Do not work on the system or connect or disconnect cables during periods of lightning activity.

Statement 1001

Statement 1026

Statement 1021

OL-21559-01

Cisco Connected Grid Routers 2010 Hardware Installation Guide

3-17

Connecting WAN and LAN Interfaces

REVIEW DRAFT—CISCO CONFIDENTIAL

Ports and Cabling

Table 3-2 summarizes typical WAN and LAN connections for Cisco 2010 CGR routers. The connections

summarized here are also described in detail in Cisco Modular Access Router Cable Specifications.

Ta b l e 3-2 WAN, LAN, and Voice Connections

Chapter 3 Installing and Connecting the Router

Port or Connection Port Type, Color

Connection: Cable

Ethernet RJ-45, yellow Ethernet hub or Ethernet switch Category 5 or higher Ethernet

T1/E1 WAN RJ-48C/CA81A T1 or E1 network RJ-48 T1/E1

Cisco serial 60-pin D-sub, blue CSU/DSU and serial network or

equipment

Cisco Smart serial Cisco Smart compact

connector, blue

56/64-kbps

8-pin modular, blue RJ-48S interface in subrate device

DSU/CSU

CSU/DSU and serial network or equipment

or network

Cisco serial transition cable that matches the signaling protocol (EIA/TIA-232, V.35 or X.21 and the serial port operating mode (DTE or DCE).3

RJ-48 straight-through

T1/FT1 DSU/CSU 8-pin modular, blue RJ-48C interface RJ-48 straight-through

Gigabit Ethernet SFP, optical

Gigabit Ethernet SFP,

LC, color according to optical wavelength

1000BASE-SX, -LX, -ZX, 100BASE-FX and 100BASE-LX

Optical fiber as specified on applicable data sheet

RJ-45 1000BASE-T Category 5, 5e, 6 UTP

copper

1. Cable color codes are specific to Cisco cables.

2. For T1/E1 interfaces, shielded cables are required to meet EN55022, Cispr 22, and EN300-386 compliance.

3. See Cisco Modular Access Router Cable Specifications for information about choosing these cables.

Connection Procedures and Precautions

3-18

To properly connect cables follow these steps:

Step 1 Connect each WAN and LAN cable to the appropriate connector on the chassis or on an interface card. Step 2 Position the cables carefully, so that they do not put strain on the connectors. Step 3 Organize cables in bundles so that cables do not intertwine. Step 4 Inspect the cables to make sure that the routing and bend radius is satisfactory. Reposition cables, if

necessary.

Note Install cable ties in accordance with site requirements.

For cable pinouts, see Cisco Modular Access Router Cable Specifications on www.cisco.com.

Cisco Connected Grid Routers 2010 Hardware Installation Guide

OL-21559-01

Configuring the Router

This document describes how to power up the router and perform the initial configuration in the following sections:

• Powering up the Router

• Performing the Initial Configuration on the Router

• Verifying the Initial Configuration

Powering up the Router

Warning

1029

CHA PTER

Statement

This section covers the following topics:

• Powering up the Router, page 4-1

• Performing the Initial Configuration on the Router, page 4-3

• Verifying Network Connectivity, page 4-20

• Verifying the Initial Configuration, page 4-24

Checklist for Power Up

Check the following items before powering up the router:

• Chassis is securely mounted and grounded.

• Interface cables are connected.

• Compact flash memory card is properly seated into its slot. For installation instructions, see the

“Removing and Installing Compact Flash Memory Cards” section on page 5-3.

• PC with terminal emulation program (HyperTerminal or equivalent) is connected to the console port

and configured for 9600

• Suitable PC COM port is selected in the terminal emulation program.

OL-21559-01

baud, 8 data bits, 1 stop bit, no parity, and flow control is set to “none.”

Cisco Connected Grid Routers 2010 Hardware Installation Guide

4-1

Powering up the Router

• Passwords for access control are selected.

• IP addresses for the Ethernet and serial interfaces have been determined.

Power Up Procedure

To power up your Cisco router, follow this procedure to verify the router has performed the initialization and self-test. When the procedure is finished, the router is ready to configure.

If you encounter problems while powering on the router, see the Troubleshooting page for the router on www.cisco.com.

For information about the ROM monitor and the bootstrap program, see Using the ROM Monitor in the software configuration guide for the router. For information about the configuration register, see

Changing the Configuration Register Settings in the software configuration guide for the router.

Note To view the boot sequence, you must establish console connection to the Cisco router before it powers

up.

Chapter 4 Configuring the Router

Step 1 Make sure that your PC is powered up and connected as described in the “Checklist for Power Up”

section on page 4-1.

Step 2 Make connectivity to the power blocks.

• SYS LED on the front of the chassis begins blinking green.

• Startup messages appear in your Console window. When the startup messages finish, the SYS LED

appears solid green.

Caution Do not press any keys on the keyboard until the messages stop and the SYS LED is solid green. Any keys

pressed during this time are interpreted as the first command typed when the messages stop, which might cause the router to power off and start over. It takes a few minutes for the messages to stop.

If you encounter a problem during the power up process, see Troubleshooting on the www.cisco.com product page.

Step 3 Use any of the following tools to perform the initial configuration.

• Cisco Configuration Professional Express, page 4-3

Note Cisco recommends using Cisco Configuration Professional Express to perform the initial

configuration on the router because it provides a web-based graphical-user interface. See the

“Cisco Configuration Professional Express” section on page 4-3.

4-2

• Cisco Setup Command Facility, page 4-2

• Cisco Command Line Interface, page 4-3

Cisco Setup Command Facility

Cisco Setup Command Facility lets you configure the initial router settings through a configuration dialog. If you see the following messages, the router has booted and is ready for initial configuration using the setup command facility.

--- System Configuration Dialog ---

Cisco Connected Grid Routers 2010 Hardware Installation Guide

OL-21559-01

Chapter 4 Configuring the Router

At any point you may enter a question mark '?' for help. Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets '[]'.

Would you like to enter the initial configuration dialog? [yes/no]:

See the “Performing the Initial Configuration on the Router” section on page 4-3 for additional information.

Note If the system configuration dialog message does not appear, a default configuration file was

Cisco Configuration Professional Express

Use the Cisco Configuration Professional Express web-based application to configure the initial router settings. See instructions.

Performing the Initial Configuration on the Router

installed on the router prior to shipping. See the

Express” section on page 4-7 to configure the router.

Cisco Configuration Professional Express User Guide on www.cisco.com for detailed

“Using Cisco Configuration Professional

Cisco Command Line Interface

Cisco Command Line Interface (CLI) lets you configure the initial router settings manually. If you see the following messages, the router has booted and is ready for initial configuration using the CLI. For how to use the CLI to configure the router, see the

section on page 4-7.

Note If the rommon 1> prompt appears, your system has booted in ROM monitor mode. For information on the

ROM monitor, see Using the ROM Monitor in the software configuration guide for the router.

“Using Cisco IOS CLI—Manual Configuration”

Verifying the Power Supply Side LED Indications

The front-panel indicator LEDs described in Table 1-3 provide power, activity, and status information useful during power up.

Performing the Initial Configuration on the Router

Use the following tools to perform the initial configuration on the router:

• Using Cisco Setup Command Facility

• Using Cisco Configuration Professional Express

• Using Cisco IOS CLI—Manual Configuration

Using Cisco Setup Command Facility

The setup command facility prompts you to enter the information that is needed to configure a router quickly. The facility guides you through a initial configuration, including LAN and WAN interfaces. For more general information about the setup command facility, see the following document:

OL-21559-01

Cisco Connected Grid Routers 2010 Hardware Installation Guide

4-3

Performing the Initial Configuration on the Router

Cisco IOS Configuration Fundamentals Configuration Guide, Release 12.4, Part 2: Cisco IOS User Interfaces:Using AutoInstall and Setup:

http://www.cisco.com/en/US/docs/ios/fundamentals/configuration/guide/12_4/cf_12_4_book.html

This section explains how to configure a hostname for the router, set passwords, and configure an interface for communication with the management network.

Note The following example and the user entries (in bold) are shown as examples only.

Note If you make a mistake while using the setup command facility, you can exit and run the setup command

facility again. Press Ctrl-C, and enter the setup command in privileged EXEC mode (Router#).

Step 1 Enter the setup command facility by using one of the following methods:

• From the Cisco IOS CLI, enter the setup command in privileged EXEC mode:

Router> enable Password: <password> Router# setup

Chapter 4 Configuring the Router

--- System Configuration Dialog --Continue with configuration dialog? [yes/no]:

You are now in the Setup Configuration Utility.

The following steps and the user entries (in bold) are shown as examples only.

If you make a mistake while using the setup command facility, you can exit and run the setup command facility again. Press Ctrl-C, and enter the setup command at the privileged EXEC mode prompt (Router#). For more information on using the setup command facility, see The Setup Command chapter in Release 12.2T:

http://www.cisco.com/en/US/docs/ios/12_2t/fun/command/reference/122tfr.html

Cisco IOS Configuration Fundamentals Command Reference

Step 2 To proceed using the setup command facility, enter yes.

Continue with configuration dialog? [yes/no]:

At any point you may enter a question mark '?' for help.

Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets '[]'.

Basic management setup configures only enough connectivity.

Would you like to enter basic management setup? [yes/no]: yes

Step 3 Enter a hostname for the router (this example uses myrouter):

Configuring global parameters: Enter host name [Router]: my router

4-4

Step 4 Enter an enable secret password. This password is encrypted (for more security) and cannot be seen

when viewing the configuration.

The enable secret is a password used to protect access to privileged EXEC and configuration modes. This password, after entered, becomes encrypted in the configuration.

Cisco Connected Grid Routers 2010 Hardware Installation Guide

OL-21559-01

Chapter 4 Configuring the Router

Enter enable secret: password1

Step 5 Enter an enable password that is different from the enable secret password. This password is not

encrypted (and is less secure) and can be seen when viewing the configuration.

The enable password is used when you do not specify an enable secret password, with some older software versions, and some boot images. Enter enable password: password2

Step 6 Enter the virtual terminal password, which prevents unauthenticated access to the router through ports

other than the console port:

The virtual terminal password is used to protect access to the router over a network interface. Enter virtual terminal password: password3

Step 7 Respond to the following prompts as appropriate for your network:

Configure SNMP Network Management? [no]: yes Community string [public]:

A summary of the available interfaces is displayed.

Performing the Initial Configuration on the Router

Note The interface summary includes interface numbering, which is dependent on the router model

and the installed modules and interface cards.

Current interface summary

Interface IP-Address OK? Method Status Protocol GigabitEthernet0/0 unassigned YES NVRAM administratively down down GigabitEthernet0/1 10.10.10.12 YES DHCP up up SSLVPN-VIF0 unassigned NO unset up

Any interface listed with OK? value "NO" does not have a valid configuration

Step 8 Select one of the available interfaces for connecting the router to the management network:

Enter interface name used to connect to the management network from the above interface summary: gigabitethernet0/1

Step 9 Respond to the following prompts as appropriate for your network:

Configuring interface GigabitEthernet0/1: Configure IP on this interface? [yes]: yes IP address for this interface [10.10.10.12]: Subnet mask for this interface [255.0.0.0] : 255.255.255.0 Class A network is 10.0.0.0, 24 subnet bits; mask is /24

The following configuration command script is created:

hostname myrouter enable secret 5 $1$t/Dj$yAeGKviLLZNOBX0b9eifO0 enable password cisco123 line vty 0 4 password cisco snmp-server community public ! no ip routing

OL-21559-01

! interface GigabitEthernet0/0 shutdown no ip address ! interface GigabitEthernet0/1

Cisco Connected Grid Routers 2010 Hardware Installation Guide

4-5

Performing the Initial Configuration on the Router

no shutdown ip address 10.10.10.12 255.255.255.0 ! end

Step 10 Respond to the following prompts. Select [2] to save the initial configuration:

[0] Go to the IOS command prompt without saving this config. [1] Return back to the setup without saving this config. [2] Save this configuration to nvram and exit.

Enter your selection [2]: 2 Building configuration... Use the enabled mode 'configure' command to modify this configuration.

Press RETURN to get started! RETURN

The user prompt is displayed:

myrouter>

Completing the Configuration

Chapter 4 Configuring the Router

When using the Cisco Setup, and after you have provided all the information requested by the facility, the final configuration appears. To complete your router configuration, follow these steps:

The facility prompts you to save the configuration.

• If you answer no, the configuration information you entered is not saved, and you return to the router

enable prompt (Router#). Enter setup to return to the System Configuration Dialog.

• If you answer yes, the configuration is saved, and you are returned to the user EXEC prompt

(Router>).

Use this configuration? {yes/no} : yes Building configuration... Use the enabled mode 'configure' command to modify this configuration.

Press RETURN to get started!

%LINK-3-UPDOWN: Interface Ethernet0/0, changed state to up %LINK-3-UPDOWN: Interface Ethernet0/1, changed state to up %LINK-3-UPDOWN: Interface Serial1/0, changed state to up

Step 1 When the messages stop appearing on your screen, press Return to get the Router> prompt.

Note If you see the next message, it means that no other routers were found on the network attached

to the port.

4-6

%AT-6-ONLYROUTER: Ethernet0/0: AppleTalk port enabled; no neighbors found

Step 2 The Router> prompt indicates that you are now at the command-line interface (CLI) and you have just

completed a initial router configuration. Nevertheless, this is not a complete configuration. At this point, you have two choices:

• Run the setup command facility again, and create another configuration.

Cisco Connected Grid Routers 2010 Hardware Installation Guide

OL-21559-01

Chapter 4 Configuring the Router

Router> enable Password: Router# setup

• Modify the existing configuration or configure additional features by using the CLI.

Router> enable Password: Router# configure terminal Router(config)#

password

Using Cisco Configuration Professional Express

Use Cisco Configuration Professional Express web-based application to configure the initial router settings. See instructions.

For help with interface and port numbering, see the “Slot, Port, and Interface Information” section on

page 1-6.

Cisco Configuration Professional Express User Guide on www.cisco.com for detailed

Performing the Initial Configuration on the Router

Using Cisco IOS CLI—Manual Configuration

This section shows you how to access the command-line interface (CLI) to perform the initial configuration on the router.

If the system configuration dialog message does not appear, a default configuration file was installed on the router prior to shipping. See the

page 4-7 to configure the router.

For help with interface and port numbering, see the “Slot, Port, and Interface Information” section on

page 1-6.

Step 1 Enter the following answer when the system message appears on the router.

--- System Configuration Dialog ---

At any point you may enter a question mark '?' for help. Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets '[]'.

Would you like to enter the initial configuration dialog? [yes/no]: no

Step 2 Press Return to terminate autoinstall and continue with manual configuration:

Would you like to terminate autoinstall? [yes] Return

Several messages are displayed, ending with a line similar to the following:

...

date

> <

time

> by <

“Using Cisco Configuration Professional Express” section on

person

OL-21559-01

Cisco Connected Grid Routers 2010 Hardware Installation Guide

4-7

Performing the Initial Configuration on the Router

Step 3 Press Return to bring up the Router> prompt.

...

flashfs[4]: Initialization complete. Router>

Step 4 Type enable to enter privileged EXEC mode:

Router> enable Router#

The following tasks are either required or optional:

• Configuring the Router Hostname, page 4-8 (Optional)

• Configuring the Enable and Enable Secret Passwords, page 4-9 (Required)

• Configuring the Console Idle Privileged EXEC Timeout, page 4-10 (Optional)

• Configuring Gigabit Ethernet Interfaces, page 4-12 (Required)

• Specifying a Default Route or Gateway of Last Resort, page 4-14 (Required)

• Configuring IP Routing and IP Protocols, page 4-14 (Required)

• Default Routes, page 4-15 (Optional)

Chapter 4 Configuring the Router

• Default Network, page 4-15 (Optional)

• Configuring Virtual Terminal Lines for Remote Console Access, page 4-17 (Required)

• Configuring the Auxiliary Line, page 4-19 (Optional)

Configuring the Router Hostname

The hostname is used in CLI prompts and default configuration filenames. If you do not configure the router hostname, the router uses the factory-assigned default hostname “Router.”

Do not expect capitalization and lower casing to be preserved in the hostname. Uppercase and lowercase characters are treated as identical by many Internet software applications. It may seem appropriate to capitalize a name as you would ordinarily do, but conventions dictate that computer names appear in all lowercase characters. For more information, see the RFC 1178, Choosing a Name for Your Computer.

The name must also follow the rules for Advanced Research Projects Agency Network (ARPANET) hostnames. They must start with a letter, end with a letter or digit, and have as interior characters only letters, digits, and hyphens. Names must be 63 characters or fewer. For more information, see the RFC 1035, Domain Names—Implementation and Specification.

SUMMARY STEPS

1. enable

2. configure terminal

3. hostname name

4. Verify that the router prompt displays your new hostname.

4-8

5. end

Cisco Connected Grid Routers 2010 Hardware Installation Guide

OL-21559-01

Chapter 4 Configuring the Router

DETAILED STEPS

Command or Action Purpose

Step 1

enable

Example:

Router> enable

Step 2

configure terminal

Example:

Router# configure terminal

Step 3

hostname

name

Example:

Router(config)# hostname myrouter

Step 4

Verify that the router prompt displays your new hostname.

Performing the Initial Configuration on the Router

Enables privileged EXEC mode.

• Enter your password if prompted.

Enters global configuration mode.

Specifies or modifies the hostname for the network server.

—

Example:

myrouter(config)#

Step 5

end

(Optional) Returns to privileged EXEC mode.

Example:

myrouter# end

Configuring the Enable and Enable Secret Passwords

To provide an additional layer of security, particularly for passwords that cross the network or are stored on a TFTP server, use either the enable password command or the enable secret command. Both commands accomplish the same thing—they allow you to establish an encrypted password that users must enter to access privileged EXEC (enable) mode.

We recommend that you use the enable secret command because it uses an improved encryption algorithm. Use the enable password command only if you boot an older version of the Cisco IOS software or if you boot older boot ROMs that do not recognize the enable secret command.

For more information, see the “Configuring Passwords and Privileges” chapter in Cisco IOS Security

Configuration Guide. Also see

Routers.

Restrictions

If you configure the enable secret command, it takes precedence over the enable password command; the two commands cannot be in effect simultaneously.

Cisco IOS Password Encryption Facts and Improving Security on Cisco

SUMMARY STEPS

OL-21559-01

1. enable

2. configure terminal

Cisco Connected Grid Routers 2010 Hardware Installation Guide

4-9

Performing the Initial Configuration on the Router

3. enable password password

4. enable secret password

5. end

6. enable

7. end

DETAILED STEPS

Command or Action Purpose

Step 1

enable

Example:

Router> enable

Step 2

configure terminal

Chapter 4 Configuring the Router

Enables privileged EXEC mode.

• Enter your password if prompted.

Enters global configuration mode.

Step 3

Step 4

Step 5

Step 6

Step 7

Example:

Router# configure terminal

enable password

password

Example:

Router(config)# enable password pswd2

enable secret

password

Example:

Router(config)# enable secret

end

greentree

Example:

Router(config)# end

enable

Example:

Router> enable

end

(Optional) Sets a local password to control access to various privilege levels.

• We recommend that you perform this step only if you

boot an older image of the Cisco IOS software or if you boot older boot ROMs that do not recognize the enable secret command.

Specifies an additional layer of security over the enable password command.

• Do not use the same password that you entered in

Step 3.

Returns to privileged EXEC mode.

Enables privileged EXEC mode.

• Verify that your new enable or enable secret password

works.

(Optional) Returns to privileged EXEC mode.

Example:

Router(config)# end

Configuring the Console Idle Privileged EXEC Timeout

This section describes how to configure the console line idle privileged EXEC timeout. By default, the privileged EXEC command interpreter waits 10 minutes to detect user input before timing out.

Cisco Connected Grid Routers 2010 Hardware Installation Guide

4-10

OL-21559-01

Chapter 4 Configuring the Router

When you configure the console line, you can also set communication parameters, specify autobaud connections, and configure terminal operating parameters for the terminal that you are using. For more information on configuring the console line, see the Cisco IOS Configuration Fundamentals and Network Management Configuration Guide. In particular, see the “Configuring Operating Characteristics for Terminals” and “Troubleshooting and Fault Management” chapters.

SUMMARY STEPS

1. enable

2. configure terminal

3. line console 0

4. exec-timeout minutes [seconds]

5. end

6. show running-config

DETAILED STEPS

Performing the Initial Configuration on the Router

Step 1

Step 2

Step 3

Step 4

Command or Action Purpose

enable

Enables privileged EXEC mode.

• Enter your password if prompted.

Example:

Router> enable

configure terminal

Enters global configuration mode.

Example:

Router# configure terminal

line console 0

Configures the console line and starts the line configuration command collection mode.

Example:

Router(config)# line console 0

exec-timeout

minutes [seconds

]

Sets the idle privileged EXEC timeout, which is the interval that the privileged EXEC command interpreter waits until

Example:

Router(config-line)# exec-timeout 0 0

user input is detected.

• The example shows how to specify no timeout. Setting

the exec-timeout value to 0 will cause the router to never log out once logged in. This could have security implications if you leave the console without manually logging out using the disable command.

OL-21559-01

Cisco Connected Grid Routers 2010 Hardware Installation Guide

4-11

Performing the Initial Configuration on the Router

Command or Action Purpose

Step 5

end

Example:

Router(config)# end

Step 6

show running-config

Example:

Router(config)# show running-config

Examples

The following example shows how to set the console idle privileged EXEC timeout to 2 minutes 30 seconds:

line console exec-timeout 2 30

The following example shows how to set the console idle privileged EXEC timeout to 10 seconds:

line console exec-timeout 0 10

Chapter 4 Configuring the Router

Returns to privileged EXEC mode.

Displays the running configuration file.

• Verify that you properly configured the idle privileged

EXEC timeout.

Configuring Gigabit Ethernet Interfaces

This section shows how to assign an IP address and interface description to an Ethernet interface on your router.

For comprehensive configuration information on Gigabit Ethernet interfaces, see chapter “Configuring LAN Interfaces” in

For information on interface numbering, see the software configuration guide for your router.

SUMMARY STEPS

1. enable

2. show ip interface brief

3. configure terminal

4. interface {fastethernet | gigabitethernet} 0/port

5. description string

6. ip address ip-address mask

7. no shutdown

8. end

9. show ip interface brief

Cisco IOS Interface and Hardware Component Configuration Guide.

4-12

Cisco Connected Grid Routers 2010 Hardware Installation Guide

OL-21559-01

Chapter 4 Configuring the Router

DETAILED STEPS

Command or Action Purpose

Step 1

enable

Example:

Router> enable

Step 2

show ip interface brief

Performing the Initial Configuration on the Router

Enables privileged EXEC mode.

• Enter your password if prompted.

Displays a brief status of the interfaces that are configured for IP.

Step 3

Step 4

Step 5

Step 6

Step 7

Example:

Router# show ip interface brief

configure terminal

Example:

Router# configure terminal

interface {fastethernet | gigabitethernet}

port

Example:

Router(config)# interface gigabitethernet 0/0

description

string

Example:

Router(config-if)# description GE int to 2nd floor south wing

ip address

ip-address mask

Example:

Router(config-if)# ip address 172.16.74.3

255.255.255.0

no shutdown

• Determine which type of Ethernet interface is on your

router.

Enters global configuration mode.

Specifies the Ethernet interface and enters interface configuration mode.

Note For information on interface numbering, see the

software configuration guide.

(Optional) Adds a description to an interface configuration.

• The description helps you remember what is attached to

this interface. The description can be useful for troubleshooting.

Sets a primary IP address for an interface.

Enables an interface.

Step 8

Step 9

OL-21559-01

Example:

Router(config-if)# no shutdown

end

Example:

Router(config)# end

show ip interface brief

Example:

Router# show ip interface brief

Returns to privileged EXEC mode.

Displays a brief status of the interfaces that are configured for IP.

• Verify that the Ethernet interfaces are up and

configured correctly.

Cisco Connected Grid Routers 2010 Hardware Installation Guide

4-13

Performing the Initial Configuration on the Router

Examples

Configuring the GigabitEthernet Interface: Example

! interface GigabitEthernet0/0 description GE int to HR group ip address 172.16.3.3 255.255.255.0 duplex auto speed auto no shutdown !

Sample Output for the show ip interface brief Command

Router# show ip interface brief

Interface IP-Address OK? Method Status Protocol GigabitEthernet0/0 172.16.3.3 YES NVRAM up up GigabitEthernet0/1 unassigned YES NVRAM administratively down down Router#

Specifying a Default Route or Gateway of Last Resort

Chapter 4 Configuring the Router

This section describes how to specify a default route with IP routing enabled. For alternative methods of specifying a default route, see

The Cisco IOS software uses the gateway (router) of last resort if it does not have a better route for a packet and if the destination is not a connected network. This section describes how to select a network as a default route (a candidate route for computing the gateway of last resort). The way in which routing protocols propagate the default route information varies for each protocol.

Configuring IP Routing and IP Protocols

For comprehensive configuration information about IP routing and IP routing protocols, see Cisco IOS

IP Routing Protocols Configuration Guide, Release 12.4T on www.cisco.com.

IP Routing

You can configure integrated routing and bridging (IRB) so the router can route and bridge simultaneously. The router acts as an IP host on the network whether routing is enabled or not.

To read more about IRB, see the following URL:

http://www.cisco.com/en/US/tech/tk389/tk815/tk855/tsd_technology_support_sub-protocol_home.htm l

IP routing is automatically enabled in the Cisco IOS software. When IP routing is configured, the system uses a configured or learned route to forward packets, including a configured default route.

Configuring a Gateway of Last Resort Using IP Commands.

4-14

Note This task section does not apply when IP routing is disabled. To specify a default route when IP routing

is disabled, see Configuring a Gateway of Last Resort Using IP Commands on www.cisco.com.

Cisco Connected Grid Routers 2010 Hardware Installation Guide

OL-21559-01

Chapter 4 Configuring the Router

Default Routes

A router might not be able to determine the routes to all other networks. To provide complete routing capability, the common practice is to use some routers as smart routers and give the remaining routers default routes to the smart router. (Smart routers have routing table information for the entire internetwork.) These default routes can be passed along dynamically, or can be configured into the individual routers.

Most dynamic interior routing protocols include a mechanism for causing a smart router to generate dynamic default information that is then passed along to other routers.

Default Network

If a router has an interface that is directly connected to the specified default network, the dynamic routing protocols running on the router generates or sources a default route. In the case of RIP, the router advertises the pseudonetwork 0.0.0.0. In the case of IGRP, the network itself is advertised and flagged as an exterior route.

A router that is generating the default for a network also may need a default of its own. One way a router can generate its own default is to specify a static route to the network 0.0.0.0 through the appropriate device.

Performing the Initial Configuration on the Router

Gateway of Last Resort

When default information is being passed along through a dynamic routing protocol, no further configuration is required. The system periodically scans its routing table to choose the optimal default network as its default route. In the case of RIP, there is only one choice, network 0.0.0.0. In the case of IGRP, there might be several networks that can be candidates for the system default. The Cisco IOS software uses both administrative distance and metric information to determine the default route (gateway of last resort). The selected default route appears in the gateway of last resort display of the show ip route EXEC command.

If dynamic default information is not being passed to the software, candidates for the default route are specified with the ip default-network global configuration command. In this usage, the ip default-network command takes an unconnected network as an argument. If this network appears in the routing table from any source (dynamic or static), it is flagged as a candidate default route and is a possible choice as the default route.

If the router has no interface on the default network, but does have a route to it, it considers this network as a candidate default path. The route candidates are examined and the best one is chosen, based on administrative distance and metric. The gateway to the best default path becomes the gateway of last resort.

SUMMARY STEPS

1. enable

2. configure terminal

OL-21559-01

3. ip routing

4. ip route dest-prefix mask next-hop-ip-address [admin-distance] [permanent]

5. ip default-network network-number

or ip route dest-prefix mask next-hop-ip-address

Cisco Connected Grid Routers 2010 Hardware Installation Guide

4-15

Performing the Initial Configuration on the Router

6. end

7. show ip route

DETAILED STEPS

Command or Action Purpose

Step 1

enable

Example:

Router> enable

Step 2

configure terminal

Example:

Router# configure terminal

Step 3

ip routing

Chapter 4 Configuring the Router

Enables privileged EXEC mode.

• Enter your password if prompted.

Enters global configuration mode.

Enables IP routing.

Step 4

Step 5

Step 6

Step 7

Example:

Router(config)# ip routing

ip route

admin-distance

[

dest-prefix mask next-hop-ip-address

] [permanent]

Example:

Router(config)# ip route 192.168.24.0

255.255.255.0 172.28.99.2

ip default-network

ip route

dest-prefix mask next-hop-ip-address

network-number

Example:

Router(config)# ip default-network 192.168.24.0

Example:

Router(config)# ip route 0.0.0.0 0.0.0.0

172.28.99.1

end

Example:

Router(config)# end

show ip route

Establishes a static route.

Selects a network as a candidate route for computing the gateway of last resort.

Creates a static route to network 0.0.0.0 0.0.0.0 for computing the gateway of last resort.

Returns to privileged EXEC mode.

Displays the current routing table information.

4-16

• Verify that the gateway of last resort is set.

Example:

Router# show ip route

Cisco Connected Grid Routers 2010 Hardware Installation Guide

OL-21559-01

Chapter 4 Configuring the Router

Examples

Specifying a Default Route: Example

! ip routing ! ip route 192.168.24.0 255.255.255.0 172.28.99.2 ! ip default-network 192.168.24.0 !

Sample Output for the show ip route Command

Router# show ip route

Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, * - candidate default Gateway of last resort is 172.28.99.2 to network 192.168.24.0

172.24.0.0 255.255.255.0 is subnetted, 1 subnets C 172.24.192.0 is directly connected, FastEthernet0 S 172.24.0.0 255.255.0.0 [1/0] via 172.28.99.0 S* 192.168.24.0 [1/0] via 172.28.99.2

172.16.0.0 255.255.255.0 is subnetted, 1 subnets C 172.16.99.0 is directly connected, FastEthernet1 Router#

Performing the Initial Configuration on the Router

Configuring Virtual Terminal Lines for Remote Console Access

Virtual terminal (vty) lines are used to allow remote access to the router. This section shows you how to configure the virtual terminal lines with a password, so that only authorized users can remotely access the router.

The router has five virtual terminal lines by default. However, you can create additional virtual terminal lines as described in Cisco IOS Terminal Services Configuration Guide, Release 12.4. See

http://www.cisco.com/en/US/docs/ios/termserv/configuration/guide/tsv_term_op_char_dialin_ps6350_ TSD_Products_Configuration_Guide_Chapter.html.

Line passwords and password encryption is described in the Cisco IOS Security Configuration Guide, Release 12.4. See

http://www.cisco.com/en/US/docs/ios/security/configuration/guide/12_4/sec_12_4_book.pdf.

Note To secure the vty lines with an access list, see http://www.cisco.com/en/US/products/index.html

and

http://www.cisco.com/en/US/tech/tk59/technologies_tech_note09186a00809d38a7.shtml.

SUMMARY STEPS

1. enable

2. configure terminal

OL-21559-01

3. line vty line-number [ending-line-number]

Cisco Connected Grid Routers 2010 Hardware Installation Guide

4-17

Performing the Initial Configuration on the Router

4. password password

5. login

6. end

7. show running-config

8. From another network device, attempt to open a Telnet session to the router.

DETAILED STEPS

Command or Action Purpose

Step 1

enable

Example:

Router> enable

Step 2

configure terminal

Chapter 4 Configuring the Router

Enables privileged EXEC mode.

• Enter your password if prompted.

Enters global configuration mode.

Step 3

Step 4

Step 5

Step 6

Example:

Router# configure terminal

line vty

line-number [ending-line-number

Example:

Router(config)# line vty 0 4

password

Example:

Router(config-line)# password

Example:

Router(config-line)# login

end

Example:

Router(config-line)# end

guessagain

]

Starts the line configuration command collection mode for the virtual terminal lines (vty) for remote console access.

• Make sure that you configure all vty lines on your

router.

Note To verify the number of vty lines on your router, use

the line vty ? command.

Specifies a password on a line.

Enables password checking at login.

Returns to privileged EXEC mode.

4-18

Cisco Connected Grid Routers 2010 Hardware Installation Guide

OL-21559-01

Chapter 4 Configuring the Router

Command or Action Purpose

Step 7

show running-config

Example:

Router# show running-config

Step 8

From another network device, attempt to open a Telnet session to the router.

Example:

Router# 172.16.74.3 Password:

Examples

The following example shows how to configure virtual terminal lines with a password:

! line vty 0 4 password anyname login !

Performing the Initial Configuration on the Router

Displays the running configuration file.

• Verify that you properly configured the virtual terminal

lines for remote access.

Verifies that you can remotely access the router and that the virtual terminal line password is correctly configured.

What to Do Next

After you configure the vty lines, follow these steps:

• (Optional) To encrypt the virtual terminal line password, see the “Configuring Passwords and

Privileges” chapter in Cisco IOS Security Configuration Guide. Also see the

Encryption Facts tech note.

• (Optional) To secure the VTY lines with an access list, see the “Part 3: Traffic Filtering and

Firewalls” chapter in Cisco IOS Security Configuration Guide.

Configuring the Auxiliary Line

This section describes how to enter line configuration mode for the auxiliary line. How you configure the auxiliary line depends on your particular implementation of the auxiliary (AUX) port. See

Configuring a Modem on the AUX Port for EXEC Dialin Connectivity.

SUMMARY STEPS

1. enable

2. configure terminal

3. line aux 0

Note See the tech notes and sample configurations to configure the line for your particular

implementation of the AUX port.

Cisco IOS Password

OL-21559-01

Cisco Connected Grid Routers 2010 Hardware Installation Guide

4-19

Performing the Initial Configuration on the Router

DETAILED STEPS

Command or Action Purpose

Step 1

enable

Example:

Router> enable

Step 2

configure terminal

Example:

Router# configure terminal

Step 3

line aux 0

Example:

Router(config)# line aux 0

Step 4

See the tech notes and sample configurations to configure the line for your particular implementation of the AUX port.

Chapter 4 Configuring the Router

Enables privileged EXEC mode.

• Enter your password if prompted.

Enters global configuration mode.

Starts the line configuration command collection mode for the auxiliary line.

—

Verifying Network Connectivity

This section describes how to verify network connectivity for your router.

Prerequisites

• Complete all previous configuration tasks in this document.

• The router must be connected to a properly configured network host.

SUMMARY STEPS

1. enable

2. ping [ip-address | hostname]

3. telnet {ip-address | hostname}

4-20

Cisco Connected Grid Routers 2010 Hardware Installation Guide

OL-21559-01

Chapter 4 Configuring the Router

DETAILED STEPS

Command or Action Purpose

Step 1

enable

Example:

Router> enable

ping [

Step 2

ip-address

Example:

Router# ping 172.16.74.5

Step 3

telnet {

ip-address

Example:

Router# telnet 10.20.30.40

hostname

]

hostname

}

Performing the Initial Configuration on the Router

Enables privileged EXEC mode.

• Enter your password if prompted.

Diagnoses initial network connectivity.

• To verify connectivity, ping the next hop router or

connected host for each configured interface to.

Logs in to a host that supports Telnet.

• To test the vty line password, perform this step from a

different network device, and use your router’s IP address.

Examples

The following display shows sample output for the ping command when you ping the IP address

192.168.7.27:

Router# ping

Protocol [ip]: Target IP address: 192.168.7.27 Repeat count [5]: Datagram size [100]: Timeout in seconds [2]: Extended commands [n]: Sweep range of sizes [n]: Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.7.27, timeout is 2 seconds: !!!!! Success rate is 100 percent, round-trip min/avg/max = 1/2/4 ms

OL-21559-01

Cisco Connected Grid Routers 2010 Hardware Installation Guide

4-21

Performing the Initial Configuration on the Router

The following display shows sample output for the ping command when you ping the IP hostname donald:

Router# ping donald

Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.7.27, timeout is 2 seconds: !!!!! Success rate is 100 percent, round-trip min/avg/max = 1/3/4 ms

Saving Your Router Configuration

This section describes how to avoid losing your configuration at the next system reload or power cycle by saving the running configuration to the startup configuration in NVRAM. The NVRAM provides 256

KB of storage on the router.

SUMMARY STEPS

1. enable

2. copy running-config startup-config

Chapter 4 Configuring the Router

DETAILED STEPS

Command or Action Purpose

Step 1

Step 2

enable

Example:

Router> enable

copy running-config startup-config

Enables privileged EXEC mode.

• Enter your password if prompted.

Saves the running configuration to the startup configuration.

Example:

Router# copy running-config startup-config

Saving Backup Copies of Configuration and System Image

To aid file recovery and minimize downtime in case of file corruption, we recommend that you save backup copies of the startup configuration file and the Cisco IOS software system image file on a server.

4-22

Cisco Connected Grid Routers 2010 Hardware Installation Guide

OL-21559-01

Chapter 4 Configuring the Router

SUMMARY STEPS

1. enable

2. copy nvram:startup-config {ftp: | rcp: | tftp:}

3. show {flash0 | flash1}:

4. copy {flash0 | flash1}: {ftp: | rcp: | tftp:}

DETAILED STEPS

Command or Action Purpose

Step 1

enable

Example:

Router> enable

Step 2

copy nvram:startup-config {ftp: | rcp: | tftp:}

Example:

Router# copy nvram:startup-config ftp:

Step 3

show {flash0 | flash1}:

Example:

Router# show {flash0|flash1}:

Step 4

copy {flash0 | flash1}: {ftp: | rcp: | tftp:}

Performing the Initial Configuration on the Router

Enables privileged EXEC mode.

• Enter your password if prompted.

Copies the startup configuration file to a server.

• Configuration file copy can serve as a backup copy.

• Enter the destination URL when prompted.

Displays the layout and contents of a flash memory file system.

• Learn the name of the system image file.

Copies a file from flash memory to a server.

Examples

Example:

Router# copy {flash0|flash1}: ftp:

Copying the Startup Configuration to a TFTP Server: Example

The following example shows the startup configuration being copied to a TFTP server:

Router# copy nvram:startup-config tftp:

Remote host[]? 172.16.101.101

Name of configuration file to write [rtr2-confg]? <cr> Write file rtr2-confg on host 172.16.101.101?[confirm] <cr> ![OK]

Copying from Flash Memory to a TFTP Server: Example

The following example shows the use of the show {flash0 | flash1}: command in privileged EXEC mode to determine the name of the system image file, and the use of the copy {flash0|flash1}: tftp: command in privileged EXEC mode to copy the system image to a TFTP server. The router uses the default username and password.

• Copy the system image file to a server to serve as a

backup copy.

• Enter the filename and destination URL when

prompted.

OL-21559-01

Cisco Connected Grid Routers 2010 Hardware Installation Guide

4-23

Verifying the Initial Configuration

Router# show {flash0|flash1}:

System flash directory: File Length Name/status 1 4137888 cCGR2010-c2is-mz [4137952 bytes used, 12639264 available, 16777216 total] 16384K bytes of processor board System flash (Read/Write)\

Router# copy {flash0|flash1}: tftp:

IP address of remote host [255.255.255.255]? 172.16.13.110 filename to write on tftp host? cCGR2010-c2is-mz writing cCGR2010-c2is-mz !!!!... successful ftp write.

Note To avoid losing work you have completed, be sure to save your configuration occasionally as you

proceed. Use the copy

running-config startup-config command to save the configuration to

NVRAM.

Verifying the Initial Configuration

Chapter 4 Configuring the Router

Enter the following commands in the Cisco IOS to verify the initial configuration on the router:

• show version—Displays the system hardware version; the installed software version; the names and

sources of configuration files; the boot images; and the amount of installed DRAM, NVRAM, and flash memory.

• show diag—Lists and displays diagnostic information about the installed controllers, interface

processors, and port adapters.

• show interfaces—Shows interfaces are operating correctly and that the interfaces and line protocol

are in the correct state—up or down.

• show ip interface brief—Displays a summary status of the interfaces configured for IP protocol.

• show configuration—Verifies that you have configured the correct hostname and password.

When you have completed and verified the initial configuration, the specific features and functions are ready to be configured. See the Cisco 2010 CGR router software configuration guide.

Note If you need help with the interface and port numbering, see the “Slot, Port, and Interface Information”

section on page 1-6.

4-24

Cisco Connected Grid Routers 2010 Hardware Installation Guide

OL-21559-01

CHA PTER

Installing and Upgrading Internal Modules

This document describes how to install and upgrade internal modules in Cisco 2010 CGR in the following sections:

• Safety Warnings, page 5-2

• Replacing Power Supplies and Redundant Power Supplies, page 5-2

• Removing and Installing Compact Flash Memory Cards, page 5-3

• Installing SFP Modules, page 5-7

Before you perform any module replacement, read the “Safety Warnings” section on page 5-2 section and disconnect power when noted.

OL-21559-01

Cisco Connected Grid Routers 2010 Hardware Installation Guide

5-1

Safety Warnings

REVIEW DRAFT—CISCO CONFIDENTIAL

Safety Warnings

Chapter 5 Installing and Upgrading Internal Modules

Warning

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement 1030

Do not work on the system or connect or disconnect cables during periods of lightning activity.

Statement 1001

Read the installation instructions before connecting the system to the power source.

Statement 1026

Statement 1004

Replacing Power Supplies and Redundant Power Supplies

The Cisco 2010 CGR routers have replaceable power supplies. Use a Number 2 Phillips screwdriver to remove or install the power supply.

Caution Any combination of power supplies can be inserted into the chassis. Dual power supply configurations

are load sharing in redundancy mode.

A single power supply is sufficient for supporting power needs to the system; however, if a single PSU is deployed it must be in slot 1 (PSU1).

Note The power supplies are hot swappable. The power supply LED must show it is properly functioning

before removing the other power supply in the router.

Replacing the Cisco 2010 CGR Router Power Supply

To replace the power supply in a Cisco 2010 CGR router, perform the following steps. See Figure 5-1 for the locations of connectors and other components within the Cisco 2010 CGR router.

Step 1 Loosen the captive screws that fasten the power supply to the chassis. Step 2 Pull the power supply out of the chassis. See Figure 5-1.

5-2

Cisco Connected Grid Routers 2010 Hardware Installation Guide

OL-21559-01

Chapter 5 Installing and Upgrading Internal Modules

REVIEW DRAFT—CISCO CONFIDENTIAL

Figure 5-1 Removing the Cisco 2010 CGR Power Supply

PSU OK

PWR-150W-HV

PSU OK

1 Power supply 2 Power supply captive screws

Step 3 Insert the replacement power supply into the chassis. See Figure 5-1. Step 4 Tighten the captive screws that fasten the power supply to the chassis.

CAUTION: This unit may have more than one power source. Disconnect all power sources before servicing to avoid electric shock.

PWR-150W-HV

PSU1 PSU2

SFP

GE 0/0

0/1

SLOT

SLOT ACT

ACT

0/1

0/0

0/1

0/1 EN

0/0

0/0 EN

LINK

USB

PSU

CON

23 1 CONSOLE

231

CONSOLE

CON

“CAUTION: This unit may have more than one power source.

Disconnect all power sources before servicing to avoid electric chock.”

CF1

CF1 CF0

DO NOT REMOVE DURING

DO NOT REMOVE DURING NETWORK OPERATION

NETWORK OPERATION

SYS SPD

SPD SPD

SPD 2 0 1USB

SPD 2 0 1

Removing and Installing Compact Flash Memory Cards

PWR-150W-HV

PSU OK

PS Type

Input Rating Per Sources

LoV dc

24-60V

HiV dc

CF0

10A

100-270V

V ac, 50/60 Hz

DO NOT REMOVE DURING

NETWORK OPERATION

100-240V ~

Cisco 2935R

Input Terminal

Type

Symbol

Lo V DC

Lo 24 - 60 V 10A

Hi V DC

Hi or V AC

Cisco Connected Grid Router 2000 Series

Input Rating Per Source

100-250V 2A

100-240V

50-60 Hz

277597

Removing and Installing Compact Flash Memory Cards

This section describes installing and replacing compact flash (CF) memory cards in Cisco 2010 CGR routers. It contains the following sections:

• Preventing Electrostatic Discharge Damage, page 5-3

• Removing a Compact Flash Memory Card, page 5-4

• Installing a Compact Flash Memory Card, page 5-6

Preventing Electrostatic Discharge Damage

Compact flash memory cards are sensitive to electrostatic discharge (ESD) damage, which can occur when electronic cards or components are handled improperly, results in complete or intermittent failures.

To prevent ESD damage, follow these guidelines:

• Always use an ESD wrist or ankle strap and ensure that it makes good skin contact.

• Connect the equipment end of the strap to an unfinished chassis surface.

• Place a removed compact flash memory card on an antistatic surface or in a static shielding bag. If

the card will be returned to the factory, immediately place it in a static shielding bag.

• Avoid contact between the card and clothing. The wrist strap protects the card from ESD voltages

on the body only; ESD voltages on clothing can still cause damage.

• Do not remove the wrist strap until the installation is complete.

OL-21559-01

Caution For safety, periodically check the resistance value of the antistatic strap. The measurement should be

between 1 and 10 megohms (Mohms).

Cisco Connected Grid Routers 2010 Hardware Installation Guide

5-3

Removing and Installing Compact Flash Memory Cards

PSU2

PSU OK

PWR-150W-HV

CF1 CF0

REVIEW DRAFT—CISCO CONFIDENTIAL

Removing a Compact Flash Memory Card

To remove a compact flash memory card from the chassis, perform the following steps. See Figure 5-2,

Figure 5-3, and Figure 5-4.

Caution Do not remove a compact flash memory card from the chassis while it is being accessed. The CF LED

blinks to indicate when flash memory is being accessed. Removing the compact flash memory card from the router while flash memory is being accessed can cause data corruption and erratic operation.

Step 1 Remove the compact flash cover by placing a flat-blade screwdriver in the slot and pushing sideways

against the tension to release the cover door. (See

Figure 5-2 Inserting Screwdriver Into the Compact Flash Cover

Chapter 5 Installing and Upgrading Internal Modules

Figure 5-2 and Figure 5-3.)

DO NOT REMOVE DURING

NETWORK OPERATION

DO NOT REMOVE DURING

NETWORK OPERATION

Type

Lo V DC

Hi V DC

V AC

Cisco Connected

277598

5-4

Cisco Connected Grid Routers 2010 Hardware Installation Guide

OL-21559-01

Chapter 5 Installing and Upgrading Internal Modules

PSU2

PSU OK

PWR-150W-HV

CF1 CF0

REVIEW DRAFT—CISCO CONFIDENTIAL

Figure 5-3 Removing the Compact Flash Cover

DO NOT REMOVE DURING

NETWORK OPERATION

DO NOT REMOVE DURING

NETWORK OPERATION

Removing and Installing Compact Flash Memory Cards

Type

Lo V DC

Hi V DC

V AC

Cisco Connected

277599

Step 2 Press the ejector button next to the compact flash memory card. The ejector button moves outward so

that it projects from the panel.

OL-21559-01

Cisco Connected Grid Routers 2010 Hardware Installation Guide

5-5

Removing and Installing Compact Flash Memory Cards

PSU2

PSU OK

PWR-150W-HV

CF1 CF0

REVIEW DRAFT—CISCO CONFIDENTIAL

Figure 5-4 Compact Flash Memory Card Slot in Cisco 2010 CGR

DO NOT REMOVE DURING

NETWORK OPERATION

DO NOT REMOVE DURING

NETWORK OPERATION

Chapter 5 Installing and Upgrading Internal Modules

Type

Lo V DC

Hi V DC

V AC

Cisco Connected

277600

1 Ejector button 2 Compact flash slot

Step 3 Press the ejector button again. See Figure 5-4. This ejects the compact flash memory card part-way out

of its slot.

Step 4 Pull the compact flash memory card out of its slot. Step 5 Push the ejector button in until the button is flush with the bezel.

Caution To prevent damage to the ejector mechanism, the ejector button must remain pressed in all the way (flush

against the bezel) when not being used to eject a compact flash memory card.

Installing a Compact Flash Memory Card

To install a compact flash memory card, perform the following steps:

Step 1 Make sure that the ejector button is fully seated until it is flush with the bezel.

Note If the ejector button is projecting out from the panel, push it in until it is flush with the bezel.

Step 2 Insert the compact flash memory card into the slot until it is fully seated. The ejector button remains

flush with the panel.

5-6

Cisco Connected Grid Routers 2010 Hardware Installation Guide

OL-21559-01

Chapter 5 Installing and Upgrading Internal Modules

REVIEW DRAFT—CISCO CONFIDENTIAL

Note If the ejector button is projecting from the panel after you insert the compact flash memory card,

remove the compact flash memory card, press the ejector button until it clicks, and reinsert the compact flash memory card.

Caution To prevent damage to the ejector mechanism, the ejector button must remain fully seated when not being

used to eject a compact flash memory card.

Step 3 Replace the compact flash cover by inserting the cover lip into the chassis then pushing the over to snap

it back into place.

Installing SFP Modules

This section describes how to install optional small-form-factor pluggable (SFP) modules in Cisco 2010 CGR routers to provide optical Gigabit Ethernet connectivity.

Installing SFP Modules

The rugged SFP SKUs supported on the Cisco 2010 CGR:

• GLC-FE-100FX-RGD=

• GLC-FE-100LX-RGD=

• GLC-SX-MM-RGD=

• GLC-LX-SM-RGD=

• GLC-ZX-SM-RGD=

The SFP module installs into a slot on the router’s cable side panel. When selected in Cisco IOS software, it is assigned port gigabitethernet 0/0. The default is the built-in RJ-45 1000 Base-T connector, which is enabled on this port.

Tip Use the show controller command at the Cisco IOS prompt to determine whether you are using an SFP

certified by Cisco.

Laser Safety Guidelines

Optical SFPs use a small laser to generate the fiber-optic signal. Keep the optical transmit and receive ports covered whenever a cable is not connected to the port.

Follow these steps to install an SFP module in a Cisco 2010 CGR router:

OL-21559-01

Step 1 Slide the SFP into the router connector until it locks into position (see Figure 5-5).

Tip If the SFP uses a bale-clasp latch (see Figure 5-5), the handle should be on top of the SFP module.

Cisco Connected Grid Routers 2010 Hardware Installation Guide

5-7

Installing SFP Modules

SFP 0/0

P 0/1

E 0/0

GE 0/1

ACT

SPD

PSU

Caution Do not remove the optical port plugs from the SFP until you are ready to connect cabling.

Step 2 Connect the network cable to the SFP module.

Chapter 5 Installing and Upgrading Internal Modules

REVIEW DRAFT—CISCO CONFIDENTIAL

Figure 5-5 Installing an SFP Module

277601

Removing SFP Modules

Follow these steps to remove an SFP from a Cisco 2010 CGR router:

Step 1 Disconnect all cables from the SFP.

Caution The latching mechanism used on many SFPs locks the SFP into place when cables are connected. Do not

pull on the cabling in an attempt to remove the SFP.

Step 2 Disconnect the SFP latch (see Figure 5-6).

Note SFP modules use various latch designs to secure the module in the SFP port. Latch designs are not linked

to SFP model or technology type. For information on the SFP technology type and model, see the label on the side of the SFP.

5-8

Cisco Connected Grid Routers 2010 Hardware Installation Guide

OL-21559-01

Chapter 5 Installing and Upgrading Internal Modules

117722

REVIEW DRAFT—CISCO CONFIDENTIAL

Figure 5-6 Disconnecting SFP Latch Mechanisms

1 2 3 4

1 Sliding latch 3 Bale-clasp latch 2 Swing and slide latch 4 Plastic collar latch

Installing Grid Router WAN Interface Cards

Tip Use a pen, screwdriver, or other small straight tool to gently release a bale-clasp handle if you cannot

reach it with your fingers.

Step 3 Grasp the SFP on both sides and remove it from the router.

Installing Grid Router WAN Interface Cards

This section describes how to install grid router WAN interface cards (GRWIC) in Cisco 2010 CGR routers.

The GRWIC installs into one of four slots on the cable side panel of the router (see Figure 5-8).

Note You can install 4 single-wide GRWICs in the Cisco 2010 CGR router slots at any one time. Although

double-wide GRWICs are not supported at this time, future versions of the Cisco 2010 CGR router will also support double-wide GRWIC configurations.

OL-21559-01

Cisco Connected Grid Routers 2010 Hardware Installation Guide

5-9

Installing Grid Router WAN Interface Cards

REVIEW DRAFT—CISCO CONFIDENTIAL

Figure 5-7 GRWICs for the Cisco 2010 CGR Router

P1 P0

CD/LP AL CD/LP AL

Chapter 5 Installing and Upgrading Internal Modules

277402

Follow these steps to install a GRWIC in a Cisco 2010 CGR router:

Step 1 Slide the GRWIC in to the router slot. See Figure 5-8.

Figure 5-8 Proper Installation of Multiple GRWICs

Cisco CGR 2010

PSU2PSU1

ACT

SFP 0/0

SFP 0/1

SPD

SYS 0

GE 0/1

GE 0/0

CONSOLE

SLOT 3 SLOT 2

AUX

CD/LP AL CD/LP AL

P1 P0

SLOT 1 SLOT 0

CONN CONN

0-3

4-7

249224

Step 2 Tighten the three captive screws on the front of the interface card.

Caution For T1/E1 interfaces, shielded cables are required to meet EN55022, Cispr 22, and EN300-386

compliance.

Note When installing multiple GRWICs, the GRWICs must overlap, as shown in Figure 5-9, to ensure a secure

fit.

5-10

Cisco Connected Grid Routers 2010 Hardware Installation Guide

OL-21559-01

Chapter 5 Installing and Upgrading Internal Modules

REVIEW DRAFT—CISCO CONFIDENTIAL

Figure 5-9 Proper Installation of Multiple GRWICs

Installing Grid Router WAN Interface Cards

Cisco CGR 2010

PSU2

+ Lo

Lo +

PSU1

SFP 0/0

SFP 0/1

SPD

CF1PS

SYS 0 1

GE 0/1

2ACT

GE 0/0

AUX

CONSOLE

SLOT 3 SLOT 2 SLOT 1 SLOT 0

CONN CONN

0-3

GRWIC–8A/8-232

4-7

CD/LP AL CD/LP AL

P1 P0

GRWIC–2CE1T1-PRI

277397

OL-21559-01

Cisco Connected Grid Routers 2010 Hardware Installation Guide

5-11

Installing Grid Router WAN Interface Cards

REVIEW DRAFT—CISCO CONFIDENTIAL

Chapter 5 Installing and Upgrading Internal Modules

5-12

Cisco Connected Grid Routers 2010 Hardware Installation Guide

OL-21559-01

INDEX

AC power connection 3-7 asynchronous serial baud rates 2-9

auxiliary port

connecting to a modem 3-16 description of 2-6

baud rate

asynchronous serial 2-9

commands

exec-timeout 4-11

configuration

timeout 4-11

connecting

router to a PC 3-11

connections

AC power 3-7 asynchronous/synchronous serial 2-9 console port 2-5 DCE 2-8 DTE 2-8 Ethernet 2-7 network 2-7 serial 2-7

console port

description of 2-5

cooling recommendations 2-4

DCE connections 2-8 DTE connections 2-8

electrical safety guidelines 2-3

electrostatic discharge damage

See ESD.

ESD

damage prevention 2-3 ESD-preventive wrist strap 2-3

Ethernet cable types 2-7

Figures

rack-mounting the chassis 3-7

installation

checklist 2-10 tools required 2-9

LAN

connections 3-17 interface types 2-7

OL-21559-01

Cisco Connected Grid Routers 2010 Hardware Installation Guide

IN-1

Index

memory

compact Flash 1-5 types 1-5

network connections 2-7 NVRAM 1-5

packing list 3-4

connecting to router 3-11

power supplies

requirements 2-5

rack-mounting the chassis 3-5 racks, equipment 2-4 record keeping, site log 2-10

router

connecting to a PC 3-11

serial ports 2-8

static electricity damage 2-3

Tables

DTE and DCE devices 2-8

LAN interfaces, summary 1-4 timeout, disabling 4-11 tools required for installation 2-9

ventilation 2-4

Warnings

blank faceplates and cover panels 4-1

disconnecting multiple power supplies 2-3

installation instructions reading requirement 2-3

lightning activity 3-17

lightning activity warning 2-3

qualified personnel 2-1, 3-1

restricted access 3-2

SELV circuit 2-7

safety

guidelines 2-2 serial connections, considerations 2-7 serial port specifications 2-8

site

environment 2-5

log, record keeping 2-10

requirements 2-4

specifications

Cisco Connected Grid Routers 2010 Hardware Installation Guide

IN-2

OL-21559-01

Cisco 2010 Hardware Installation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Cisco 2010 Connected Grid Router Hardware Installation Guide

CONTENTS

Preface

Objectives

Audience

Organization

Conventions

Searching for Cisco Documents

Obtaining Documentation and Submitting a Service Request

Overview of the Router

Chassis Views

Hardware Features

Locating Chassis Features and Functions

Built-in Interface Ports

Gigabit Ethernet Ports

GE Ports

SFP Ports

USB Console Port

Removable and Interchangeable Modules and Cards

Grid Router WAN Interface Cards

Memory

Power Supplies

Slot, Port, and Interface Information

Real-Time Clock

LED Indicators

Specifications

Preparing for Router Installation

Safety Recommendations

Safety with Electricity

Preventing Electrostatic Discharge Damage

General Site Requirements

Rack Requirements

Router Environmental Requirements

Power Guidelines and Requirements

Network Cabling Specifications

Console and Auxiliary Port Considerations

Console Port Connections

EIA/TIA-232

USB Serial Console

Auxiliary Port Connections

Preparing for Network Connections

Ethernet Connections

Serial Connections

Configuring Serial Connections

Serial DTE or DCE Devices

Signaling Standards Supported

Distance Limitations

Required Tools and Equipment for Installation and Maintenance

Asynchronous/Synchronous Serial Module Baud Rates

Installation Checklist

Creating a Site Log

Installing and Connecting the Router

What you Need to Know

Before You Begin

Unpacking the Router

Installing the Router in a Rack

Rack-Mounting the Chassis

Attaching Rack-Mount Brackets to Cisco 2010 CGR Routers

Mounting the Router in a Rack

Connecting Power

Connecting Power

Shutting Off Power

Connecting to a Console Terminal or Modem

Connecting to the Serial Port with Microsoft Windows

Connecting to the Console Port with Mac OS X

Connecting to the Console Port with Linux

Installing the Cisco Microsoft Windows USB Device Driver

Installing the Cisco Microsoft Windows XP USB Driver

Installing the Cisco Microsoft Windows 2000 USB Driver

Installing the Cisco Microsoft Windows Vista USB Driver

Uninstalling the Cisco Microsoft Windows USB Driver

Uninstalling the Cisco Microsoft Windows XP and 2000 USB Driver

Uninstalling the Cisco Microsoft Windows Vista USB Driver

Connecting to the Auxiliary Port

Connecting WAN and LAN Interfaces

Ports and Cabling