Cisco Systems 2000 User Manual 2

APPENDIX

Declarations of Conformity and Regulatory Information

This appendix provides declarations of conformity and regulatory information for the Cisco Aironet 1000 Series Lightweight Access Points.

This appendix contains the following sections:

• Manufacturers Federal Communication Commission Declaration of Conformity Statement,

page B-2

• Industry Canada, page B-4

• European Community, Switzerland, Norway, Iceland, and Liechtenstein, page B-5

• Declaration of Conformity for RF Exposure, page B-7

• Guidelines for Operating Cisco Aironet Access Points in Japan, page B-8

• Administrative Rules for Cisco Aironet Access Points in Taiwan, page B-9

• Declaration of Conformity Statements, page B-11

• Declaration of Conformity Statements for European Union Countries, page B-11

OL-9403-04

Cisco Aironet 1000 Series Lightweight Access Point Hardware Installation Guide

B-1

Appendix B Declarations of Conformity and Regulatory Information

Manufacturers Federal Communication Commission Declaration of Conformity Statement

Tested To Comply With FCC Standards

FOR HOME OR OFFICE USE

Model:

AIR-AP1010-A-K9 / AIR-AP1020-A-K9 / AIR-AP1030-A-K9 AIR-AP1010-B-K9 / AIR-AP1020-B-K9 / AIR-AP1030-B-K9

FCC Certification number:

LDK102057

Manufacturer:

Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA

This device complies with Part 15 rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired

operation.

This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and radiates radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference. However, there is no guarantee that interference will not occur. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.

• Increase separation between the equipment and receiver.

• Connect the equipment to an outlet on a circuit different from which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician.

Caution The Part 15 radio device operates on a non-interference basis with other devices operating at this

frequency when using the integrated antennas. Any changes or modification to the product not expressly approved by Cisco could void the user’s authority to operate this device.

B-2

Cisco Aironet 1000 Series Lightweight Access Point Hardware Installation Guide

OL-9403-04

Appendix B Declarations of Conformity and Regulatory Information

Caution Within the 5.15 to 5.25 GHz band (5 GHz radio channels 34 to 48) the U-NII devices are restricted to

indoor operations to reduce any potential for harmful interference to co-channel Mobile Satellite System (MSS) operations.

VCCI Statement for Japan

Warning

This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual.

OL-9403-04

Cisco Aironet 1000 Series Lightweight Access Point Hardware Installation Guide

B-3

Industry Canada

Model:

AIR-AP1010-A-K9 / AIR-AP1020-A-K9 / AIR-AP1030-A-K9 AIR-AP1010-B-K9 / AIR-AP1020-B-K9 / AIR-AP1030-B-K9

Certification number:

2461B-102057

Canadian Compliance Statement

This Class B Digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numerique de la classe B respecte les exigences du Reglement sur le material broilleur du Canada.

This device complies with Class B Limits of Industry Canada. Operation is subject to the following two conditions:

Appendix B Declarations of Conformity and Regulatory Information

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired

operation.

Cisco Aironet 2.4-GHz Access Points are certified to the requirements of RSS-210 for 2.4-GHz spread spectrum devices, and Cisco Aironet 54-Mbps, 5-GHz Access Points are certified to the requirements of RSS-210 for 5-GHz spread spectrum devices. This device must be operated indoors according to the Canadian regulations. For further information, contact your local Industry Canada office.

B-4

Cisco Aironet 1000 Series Lightweight Access Point Hardware Installation Guide

OL-9403-04

Appendix B Declarations of Conformity and Regulatory Information

European Community, Switzerland, Norway, Iceland, and Liechtenstein

Model:

AIR-AP1010-E-K9 / AIR-AP1020-E-K9 / AIR-AP1030-E-K9

Declaration of Conformity with Regard to the 1999/5/EC (R&TTE Directive)

This declaration is only valid for configurations (combinations of software, firmware, and hardware) provided and supported by Cisco Systems. The use of software or firmware not provided and supported by Cisco Systems may result in the equipment no longer being compliant with the regulatory requirements.

OL-9403-04

Cisco Aironet 1000 Series Lightweight Access Point Hardware Installation Guide

B-5

+ 9 hidden pages