CIS CL-OPT200T, CL-OPT200R Product Specification & Operation Manual

CL-OPT200T/R Rev.900-759-30-00

©2013 CIS Corporation. All rights reserved.

English

Camera Link⇔Optical Signal Converter

CL-OPT200T/R

Product Specification

& Operation Manual

CIS Corporation

CL-OPT200T/R Rev.900-759-30-00

©2013 CIS Corporation. All rights reserved.

2

Table of Contents

PAGE

1.

Scope of Application ........................................................................................................................................... 3

2. Handling Precautions .......................................................................................................................................... 3

3. Product Outline .................................................................................................................................................. 5

3.1. Product Configuration ................................................................................................................................. 5

3.2. Packaging .................................................................................................................................................. 5

4. Specifications ..................................................................................................................................................... 6

4.1. General Specifications ................................................................................................................................. 6

4.2. External Input/Output Signals ..................................................................................................................... 7

5. Function Settings ............................................................................................................................................... 8

6. External Connector Interface ............................................................................................................................... 9

6.1. 6pins circular connector HR10-7R-6PA (HIROSE) or equivalent (for both CL-OPT200T/R) .......................... 9

6.2. Camera Link Connector 12226-1100-00PL (SUMITOMO 3M) ......................................................................... 9

6.3. Optical Module Connector AFBR-57D9AMZ (AVAGO) (for both CL-OPT200T/R) ............................................ 10

7. LED Status Indication ....................................................................................................................................... 11

8. Selection of Power Feeding Method ................................................................................................................... 11

9. Precautions for Power Over Camera Link (PoCL) ................................................................................................ 12

10. Connection Example ......................................................................................................................................... 12

11. Dimensions ...................................................................................................................................................... 13

11.1. CL-OPT200T Dimensions ........................................................................................................................... 13

11.2. CT-OPT200R Dimensions ........................................................................................................................... 14

12. Cases for Indemnity (Limited Warranty) ............................................................................................................. 15

13. Product Service .............................................................................................................................. .................. 15

CL-OPT200T/R Rev.900-759-30-00

1. Scope of Application

This is to describe CL-OPT200T/R signal converters enable CIS camera link cameras to connect with
frame grabber boards via optical fiber cables. All specifications contained herein are subject to
change without prior notice. Reproduction in whole or in part is prohibited.

2. Handling Precautions

The signal converters must not be used for any nuclear equipments or aerospace equipments with
which mechanical failure or malfunction could result in serious bodily injury or loss of human life.
Our warranty does not apply to damages or defects caused by irregular and/or abnormal use of the
product. Please observe all warnings and cautions stated below.

Our warranty does not apply to damages or malfunctions caused by neglecting these precautions.

z CL-OPT200T can be used only with CIS camera link cameras. Output CLK of CL-OPT200R is 81MHz

fixed. To capture the images, please use a frame grabber board corresponds to 85MHz.

z Please use a metallic frame for heat dissipation. (The recommended size of the metallic frame:

larger than H:2mm W:90mm D:90mm)

CL-OPT200T/R Main Unit

CL-OPT200Fixing Bracket

z Do not use or store the converter in the following extreme conditions:

¾ Extremely dusty or humid places.
¾ Extremely hot or cold places (operating temperature –5 to +4℃ 5)℃

z Do not apply excessive force or static electricity that could damage the converter.

z Follow the instructions in Chapter 6, “External connector interface” for connecting.

Improper connection may cause damages not only to the converter but also to the connected
devices.

©2013 CIS Corporation. All rights reserved.

3

CL-OPT200T/R Rev.900-759-30-00

z Confirm the mutual ground potential carefully and then connect the converter to monitors or
computers. AC leaks from the connected devices may cause damages or destroy the converter.

z Do not apply excessive voltage. (Use only the specified voltage.) Unstable or improper power
supply voltage may cause damages or malfunction of the converter.

z The voltage ripple of converter input power DC +12V±10% shall be within ±50mV.

z The rising time of converter input power supply voltage shall be less than +10V, Max 60ms.

Please avoid noises like chattering when rising.

In case of abnormal operation, contact the distributor from whom you purchased the product.

©2013 CIS Corporation. All rights reserved.

4

CL-OPT200T/R Rev.900-759-30-00

©2013 CIS Corporation. All rights reserved.

5

3. Product Outline

CL-OPT200T and CL-OPT200R are signal converters enable CIS camera link cameras to connect with
frame grabber boards via optical fiber cables. With optical fiber cables, data can be transmitted up to
150m length.

Please be noted that only CIS cameras can be connected to CL-OPT200T/R.

Key Features

□ With optical fiber cables, data can be transmitted up to 150m length.
□ Owing to optical fiber cable connection, no radio interference or grand noise would occur.
□ Comply with Camera Link Base/Medium Standard
□ Only CIS camera link non-PoCL and PoCL cameras can be connected.
□ As to PoCL, there are some limitations. (Please refer to page 10 for the details.)

3.1. Product Configuration

□ CL-OPT200T (Camera Link → Optical Signal Converter)
□ CL-OPT200R (Optical Signal → Camera Link Converter)

3.2. Packaging

□ Individual Carton
□ Sub Carton (10 pieces/carton)
□ Master Carton (100 pieces/carton)

Note: Master carton may change depends on the quantities to be shipped per delivery.

CL-OPT200T/R Rev.900-759-30-00

©2013 CIS Corporation. All rights reserved.

6

4. Specifications

4.1. General Specifications

(1) Power Requirements DC+12V±10% (Max voltage not to exceed 15V.)

6pins circular connector or PoCL Input (with limitation).

(2) Power Consumption CL-OPT200T : Typ 4.3W / CL-OPT200R : Typ 3.8W
(3) Dimensions

Refer to overall dimension drawing
(H:25mm W:60mm D:90mm without protruding portion)
(For both CL-OPT200T/R)

(4) Weight Approx. 200g (For both CL-OPT200T/R)
(5) Camera Link

Input/Output Connector

CL-OPT200T/R (For both CL-OPT200T/R)
mini Camera Link connector

12226-1100-00PL
(SUMITOMO 3M)

CL-OPT200T

Camera Link non-PoCL or PoCL Input
Camera Link input CLK frequency: Driver IC rated 20MHz ～ 80MHz
Base Configuration/Medium Configuration

CL-OPT200R

Camera Link Output
Camera Link output CLK frequency: 81MHz fixed
(Please connect with a frame grabber board corresponds to 85MHz.)
Base Configuration/Medium Configuration

(6) Optical Connector

LC duplex connector
Optical Module Rated: 8 Gb/s
Light wavelength: 850nm
Transmission Bandwidth: 6.125 Gb/s

AFBR-57D9AMZ(AVAGO)

(7) Optical Fiber Cable

Length

Max. 150m

(8) Supported Cameras CIS tested Camera Link, non-PoCL, and PoCL cameras.

Base Configuration Camera Series:
VCC-G22/F22 (pixel clk: 49.09MHz) series
VCC-G32/F32 (pixel clk: 72MHz) series
VCC-G60 (pixel clk: 64MHz) series
VCC-GC20/FC20 (pixel clk: 79.99MHz) series

Medium Configuration Camera Series:
VCC-F51/F52 (pixel lk: 72MHz) series
VCC-GC60/FC60 (pixel clk: 72MHz) series
VCC-GC21/FC21 (pixel clk: 80MHz) series

Cannot run the camera at Full Configuration Mode.
(Please contact our sales department regarding connections not listed
above.)

(9) Trigger Delay Referenced Value (measured value with Fujikura

DXLC-2P-PC-(L)M-GC50/125-25R Optical cable)
About 700ns (Circuit Fixed delay) + (5ns x L:Optical cable length (m))

(10) Video Delay Less than 1Line (Refer to the spec of camera to be connected.)
(11) Serial Communications 9600bps fixed

Note: Set the frame grabber at 9600bps.

(12) Safety/Quality Standards UL: Conform to UL Standard including materials and others.

CE: Emission: EN55022:2010 (Class B)

Immunity: EN61000-6-2:2005

CL-OPT200T/R Rev.900-759-30-00

RoHS: Conform to RoHS
FCC: To be applied

(13) Durability Vibration

resistance

Acceleration : 98m/s2 (10G)

Frequency

: 20～200 Hz
Direction : X,Y, and Z, 3 directions
Testing time : 120min for each direction
Shock

resistance

No malfunction shall be occurred with 980m/s

2

(100G) for

±X, ±Y, and ±Z, 6 directions. (without package)

(14) Operation Environment Operation

Temeprature

-

5 ～ +45℃ With RH 20～ 80%

With no
condensastion

(15) Storage Environment

-25 ～ +60℃ with RH20 ～ 80% with no condensation

4.2. External Input/Output Signals

(1)GPIO FVAL output :No.3pin 6pins circular connector

(LVTTL output)

External T rigger input :No.4pin

IO Interface of 6 pins circular connector at rear

©2013 CIS Corporation. All rights reserved.

7

CL-OPT200T/R Rev.900-759-30-00

5. Function Settings

With internal dip switch, trigger signals input can be selected.

(1) SW2-1

・・・

OFF : (Initial Setting)

(1) SW2-2

・・・

OFF : (Initial Setting)

(2) SW2-3 Trigger input

selection

・・・

ON : 6 pins circular connector input

OFF : Camera Link (CC1) input (Initial Setting)
(3) SW3-1 Camera Link

Configuration

・・・

OFF : Base/Medium (Initial Setting)

ON : Do not use.
(4) SW3-2

・・・

OFF : Not used (Initial Setting)

(5) SW3-3

・・・

ON : Not used

・・・

OFF : Not used (Initial Setting)

©2013 CIS Corporation. All rights reserved.

8

CL-OPT200T/R Rev.900-759-30-00

6. External Connector Interface

6.1. 6pins circular connector HR10-7R-6PA (HIROSE) or equivalent (for both CL-OPT200T/R)

©2013 CIS Corporation. All rights reserved.

9

Pin No.

1 Power Input (DC+12V)
2 Power Input (DC+12V)
3 FVAL output
4 External Trigger Input
5 GND
6 GND

6.2. Camera Link Connector 12226-1100-00PL (SUMITOMO 3M)

CL-OPT200T CN1 (Camera Link In: Base side)

Pin No. Pin No.

1 NC/+12V(PoCL) 14 GND
2 X0- 15 X0+
3 X1- 16 X1+
4 X2- 17 X2+
5 Xclk- 18 Xclk+
6 X3- 19 X3+
7 SerTC+ 20 SerTC­8 SerTFG- 21 SerTFG+
9 CC1- 22 CC1+

10 CC2+ 23 CC2­11 CC3- 24 CC3+
12 CC4+ 25 CC4­13 GND 26 NC/+12V(PoCL)

1

14

13

26

CN2 (Camera Link In: Medium Side)

Pin No. Pin No.

1 NC 14 GND
2 Y0- 15 Y0+
3 Y1- 16 Y1+
4 Y2- 17 Y2+
5 Yclk- 18 Yclk+
6 Y3- 19 Y3+
7

100Ω

20 Terminated
8 Z0- 21 Z0+
9 Z1- 22 Z1+

10 Z2- 23 Z2+
11 Zclk- 24 Zclk+
12 Z3- 25 Z3+
13 GND 26 NC

CL-OPT200T/R Rev.900-759-30-00

CL-OPT200R CN1 (Camera Link Out: Base side)

Pin No. Pin No.

1 GND/+12V(PoCL) 14 GND

25 X0- 12 X0+
24 X1- 11 X1+
23 X2- 10 X2+
22 Xclk- 9 Xclk+
21 X3- 8 X3+
20 SerTC+ 7 SerTC­19 SerTFG- 6 SerTFG+
18 CC1- 5 CC1+
17 CC2+ CC2­16 CC3- CC3+
15 CC4+ CC4­13 GND 26 GND/+12V(PoCL)

1

14

13

26

CN2 (Camera Link Out: Medium side)

Pin No. Pin No.

1 NC 14 GND

25 Y0- 12 Y0+
24 Y1- 11 Y1+
23 Y2- 10 Y2+
22 Yclk- 9 Yclk+
21 Y3- 8 Y3+
20

100Ω

7 Terminated
19 Z0- 6 Z0
18 Z1- 5 Z1+
17 Z2- 4 Z2+
16 Zclk- 3 Zclk+
15 Z3- 2 Z3+
13 GND 26 NC

6.3. Optical Module Connector AFBR-57D9AMZ (AVAGO) (for both CL-OPT200T/R)

LC duplex Connector

©2013 CIS Corporation. All rights reserved.

10

CL-OPT200T/R Rev.900-759-30-00

7. LED Status Indication

LED lights up when the camera, cable, fiber optic cable are linked normally. If it does not light up, please confirm the
followings:

z Camera link cable, camera, and fiber optic cable are not connected.
z No camera link CLK input
z Data transmission failed via optical transmission
z No power supplied to CL-OPT200T/R

8. Selection of Power Feeding Method

With internal dip switch, power feeding method can be changed.

(1) CL-OPT200T
SW1

・・・

ON : Feed the power to the converter unit via 6 pins circular

connector. No power is feeded to the camera.
(When non-PoCL camera is connected.)

(Initial Setting)

OFF : Feed the power to both of the converter unit and the

camera via 6pins ciruclar connector.

(When PoCL or PoCL-Lite camera is connected.)
(2) CL-OPT200R
SW1

・・・

ON : Feed the power to the converter unit via 6 pins circular

connector.

(Initial Setting)

OFF : Feed the power to the converter unit via the frame

grabber board.

(When PoCL frame grabber board is connected.)

©2013 CIS Corporation. All rights reserved.

11

CL-OPT200T/R Rev.900-759-30-00

©2013 CIS Corporation. All rights reserved.

12

9. Precautions for Power Over Camera Link (PoCL)

CL -OPT200R (Receiving unit) can oper ate with power fed via the fr ame grabber board, but the f ollowing
specification does not meet PoCL standard.
When feeding the power via PoCL, please confirm with the power feeding specifications of the frame
grabber board.

(1) The normal output timing of CLK output from the CL-OPT200R to the frame gr abber board shall be

maximum 10s after the last power input for the camera, the CL-OPT200T, or the CL-OPT200R.

(2) The intermittent CLK or LVAL/FVAL from the CL-OPT200R may be output to the frame grabber

board, while the camera, the CL-OPT200T, and CL-OPT200R are connected.

10. Connection Example

PoCL Feeder

connection

LC duplex Optical Cable　：　Within 150 meters

DXLC-2P-PC-50M-GC50/125-2SR

(ﾌｼﾞｸﾗ社製)

Camera Link

(Base Configuration)

Mini-CL Cable Within

meters

D26-3120-00C-300

友3M社製）

Mini-CL Cable Within
3 meters

1MD26-3560-00C-300
（住友3M社製）

Camera Link

Frame Grabber Bord

CL-OPT200R

CL-OPT200T

3

1S

（住

Circuit

CL IN(M)CL IN(B)

OPT OUTDC IN

CL-OPT200T

CL OUT(M) CL OUT(B)

OPT IN DC IN

CL-OPT200R

Image Data

T

r

i

g

g

e

r

S

ig

n

a

l

Circuit

Trigger Signal

Power
Supply

(SW2-3)

(SW2-3)

(SW1)

(SW1)

CL-OPT200T/R Rev.900-759-30-00

11. Dimensions

11.1. CL-OPT200T Dimensions

©2013 CIS Corporation. All rights reserved.

13

CL-OPT200T/R Rev.900-759-30-00

11.2. CT-OPT200R Dimensions

©2013 CIS Corporation. All rights reserved.

14

CL-OPT200T/R Rev.900-759-30-00

©2013 CIS Corporation. All rights reserved.

15

12. Cases for Indemnity (Limited Warranty)

We shall be exempted from taking responsibility and held harmless for damage or losses incurred by
the user in the following cases.

z In case damage or losses are caused by fire, earthquake, or other acts of God, acts by third party,

deliberate or accidental misuse by the user, or use under extreme operating conditions.

z In case indirect, additional, consequential damages (loss of business interests, suspension of

business activities) are incurred as result of malfunction or non-function of the equipment, we shall
be exempted from responsibility for such damages.

z In case damage or losses are caused by failure to observe the information contained in the

instructions in this product specification & operation manual.

z In case damage or losses are caused by use contrary to the instructions in this product specification

& operation manual.

z In case damage or losses are caused by malfunction or other problems resulting from use of

equipment or software that is not specified.

z In case damage or losses are caused by repair or modification conducted by the customer or any

unauthorized third party (such as an unauthorized service representative).

z Expenses we bear on this product shall be limited to the individual price of the product.

13. Product Service

In case of abnormal operation, contact the distributor from whom you purchased the product.