Cirrus Logic CDB5571 User Manual
CDB5571
100 kSps, 16-bit, High-throughput
Evaluation Board
Features
Analog Input Channels to the CS5571 ADC
Pre-configured to require a minimum number of external
connections to your data acquisition system.
All functionality accessible through the connector interface
and board-level options.
On-board 4.096 V Reference
Pre-configured for Master mode SPI™ communication to a
data capture system.
ΔΣ
ADC
General Description
The CDB5571 is a versatile tool designed for evaluating the functionality and performance of the CS5571 ADC (Analog-to-Digital
Converter). The SPI serial port on the CDB5571 evaluation board
is configured in Master mode and will start transmitting data after
power-up upon reset. This evaluation board is designed to connect
to your data capture system or will interface to the CapturePlus II
data acquisition system available from Cirrus Logic.
The CS5571 delta-sigma ADC produces fully settled conversions to
full specified accuracy at 100 kSps. This ability to produce fully settled conversions for every sample makes it suitable for converting
multiplexed input signals. To help evaluate this feature, the
CDB55 71 includes two single-ended analog inputs multiplexed into
the CS5571. The multiplexer can be switched at the CS5571 ADC
sample speed and the ADC will produce fully settled conversion data
for each input channel.
All evaluation board functionality for evaluating the CS5571 ADC is
accessed through the connector interface and board-level options.
Schematics in PADS™ PowerLogic™ format are available for
download at:
http://www.cirrus.com/en/products/pro/detail/P1120.html
ORDERING INFORMATION
CDB5571 Evaluation Board
.
www.cirrus.com
Copyright Cirrus Logic, Inc. 2009
(All Rights Reserved)
OCT ‘09
DS768DB4
CDB5571
TABLE OF CONTENTS
1. INTRODUCTION .......................................................................................................................3
1.1 Overview ............................................................................................................................ 4
2. QUICK START ..........................................................................................................................5
3. HARDWARE DESCRIPTION ...................................................................................................6
3.1 Absolute Maximum Ratings ............................................................................................... 6
3.2 Power Supply ..................................................................................................................... 6
3.3 Analog Section ................................................................................................................... 6
3.3.1 Analog Input Buffers .............................................................................................. 6
3.3.2 Multiplexer ............................................................................................................. 7
3.3.3 ADC Reset ............................................................................................................ 7
3.3.4 Voltage Reference ................................................................................................ 7
3.3.5 ADC Reference Frequency ................................................................................... 7
3.4 Digital Section .................................................................................................................... 8
3.4.1 Hardware Configuration ........................................................................................ 8
3.4.2 SPI™ Serial Port Communications ....................................................................... 8
APPENDIX A. MAXIMIZING THE PERFORMANCE OF THE CS5571 ........................................ 9
A.1 PCB Layout Considerations .............................................................................................. 9
A.2 Hardware Considerations .................................................................................................. 9
APPENDIX B. BILL OF MATERIALS ........................................................................................ 10
APPENDIX C. SCHEMATICS ..................................................................................................... 11
APPENDIX D. LAYER PLOTS ................................................................................................... 16
APPENDIX E. CALIBRATION FUNCTION ................................................................................. 25
APPENDIX E. REVISION HISTORY ..........................................................................................26
LIST OF FIGURES
Figure 1. CDB5571 Block Diagram .................................................................................................4
Figure 2. CDB5571 Board Layout ................................................................................................... 5
Figure 3. Schematic - Block Diagram............................................................................................ 11
Figure 4. Schematic - Power Supplies .......................................................................................... 12
Figure 5. Schematic - Input Buffers and Multiplexer ..................................................................... 13
Figure 6. Schematic - CS5571 ...................................................................................................... 14
Figure 7. Schematic - Configuration & Misc. ................................................................................. 15
Figure 8. Top Silkscreen ............................................................................................................... 16
Figure 9. Top Solder Mask ............................................................................................................ 17
Figure 10. Top Routing.................................................................................................................. 18
Figure 11. Ground Plane ............................................................................................................... 19
Figure 12. Power Plane................................................................................................................. 20
Figure 13. Bottom Solder Mask..................................................................................................... 21
Figure 14. Bottom Silkscreen ........................................................................................................ 22
Figure 15. Top Solder Paste Mask................................................................................................23
Figure 16. Bottom Routing ............................................................................................................ 24
LIST OF TABLES
Table 1. Power Supply Connections ...............................................................................................6
Table 2. Analog Input Connections ................................................................................................. 6
Table 3. Analog Input Channel Selection ........................................................................................ 7
Table 4. Hardware Configuration Signals........................................................................................ 8
Table 5. Serial Interface Connections ............................................................................................. 8
2 DS768DB4
CDB5571
1. INTRODUCTION
The CDB5571 evaluation board is a platform for evaluating the CS5571 ADC performance. The evaluation board is designed to connect to the SPI serial port of a processor or data capture system or will interface directly to the CapturePlus II data acquisition system available from Cirrus Logic. The CapturePlus II
data acquisition system is a powerful integrated hardware/software tool designed to fully exercise the
CDB5571 and other Cirrus Logic evaluation boards.
The CDB5571 evaluation board is designed to simplify the hardware setup required to evaluate the
CS5571. Interfacing the CDB5571 evaluation board to a user-supplied data capture system can be as
simple as connecting the SPI port and using the CDB5571 default hardware configuration. In this configuration, simply press the Reset switch on the CDB5571 and it will automatically begin transmitting data to
the data capture system.
All evaluation board functionality for evaluating the CS5571 ADC is accessed through the connector interface and board-level options.
The CS5571 delta-sigma ADC produces fully settled conversions to full specified accuracy at 100 kSps.
The ability to produce fully settled conversions for every sample makes it suitable for converting multiplexed input signals. To help evaluate this feature, the CDB5571 includes two single-ended analog inputs
multiplexed into the CS5571. The multiplexer can be switched at the CS5571 ADC sample speed and
the ADC will produce fully settled conversion data for each input channel.
For detailed information on the CS5571 ADC, please reference data sheet DS768 at www.cirrus.com
.
DS768DB4 3
CDB5571
CS5571
M
U
X
VREF
4.096 V
XTAL
16 MHz
Communication/Control
Interface
Master/Slave
Serial Port
Digital Inputs
to ADC
Digital Outputs
from ADC
IN_A
IN_B
+2.5V GND -2.5V GND +3.3V GND
J8
J6
J7
CS3004
Single-ended
Analog Inputs
Figure 1. CDB5571 Block Diagram
1.1 Overview
The CDB5571 evaluation board has both analog and digital circuit sections. The analog section consists
of the CS5571 ADC, two analog input signal buffers, controlled through a multiplexer, that condition the
signals into the ADC, and a precision 4.096 V reference. The digital section consists of board operation
configuration control signals, reset circuitry, an SPI™ serial port, a jumper connection for initiating ADC
calibration, and an EEPROM for evaluation board identification.
The evaluation board operates from +2.5V, -2.5V, +3.3V and communicates through an SPI™ serial port.
Figure 1 illustrates the CDB5571 block diagram.
4 DS768DB4
2. QUICK START
Master/Slave SPI ADC MCLK Out
Signals to ADC & Mux
Buffer Enable Calibrate 4.096 V Reference
ADC Reset Analog Inputs
DC Supply
NOTES:
1. Shaded boxes marked with "OPT. CONFIG." are not necessary for operation in an end user product.
2. Calibration function has been removed from the device but still appears on the PCB. J2 must be shorted (grounded)
for proper operation. See Appendix E for details.
2
Figure 2. CDB5571 Board Layout
CDB5571
The CDB5571 evaluation board is designed to interface with a data acquisition system. To connect and
configure the CDB5571 perform the following initialization procedure:
1. Verify that the power supplies are off.
2. Connect the power supplies to the CDB5571 as shown in Table 1 on page 6.
3. Verify that the power is off to the analog input signal & control signal sources.
4. Connect the analog input signal source to the evaluation board per Table 2 on page 6. Verify from Table 4
on page 8 that the analog input channel selected is IN_A.
5. Configure the CDB5571 by connecting the control signal sources to the evaluation board as shown in
Table 3 on page 7. Apply logic-level inputs as required to override the resistor pull-ups/pull-downs.
6. Make connections to the SPI™ serial port connector as shown in Table 5 on page 8. The CS5571 ADC
serial port is configured by default to operate in the SSC (Synchronous Self Clocking) mode. Refer to the
CS5571 data sheet for more information on serial communication modes and signal timing.
7. Turn on the power supplies to the evaluation board.
8. Apply power to the signal source.
9. Press the Reset switch on the evaluation board.
10. The CS5571 ADC's SPI™ serial port should now be communicating data.
DS768DB4 5
3. HARDWARE DESCRIPTION
3.1 Absolute Maximum Ratings
Observe the following limits to ensure the CDB5571 component ratings are not exceeded.
• CS5571
– The absolute maximum supply voltage that can be applied to the +3.3V power supply
connection is +3.6V.
– The absolute maximum power supply voltage that can be applied between pins VL and V1-
is 6.1 V.
• CS3004
– The absolute maximum power supply voltage that can be applied between the +2.5V and
-2.5V power supply connections is +5.5V.
3.2 Power Supply
Power supply connections and requirements are specified in Table 1. below.
Table 1. Power Supply Connections
CDB5571
Power Supply
Requirement
+2.5 V DC, ±5%, <50 mA E5 E3 TP2, TP1 (GND)
-2.5 V DC, ±5%, <50 mA E9 E7 TP4, TP3 (GND)
+3.3 V DC, ±5%, <50 mA E16 E13 TP6, TP5 (GND)
Power Supply
Connection
Associated
Ground Return
Associated
T est Points
Important: It is recommended that all power supplies be isolated from utility ground to prevent the introduction of a ground loop. One ground connection may already exist through the serial port connection to
utility ground. Using the Cirrus Logic CapturePlus II system simplifies making connections to the
CDB5571 by providing electrical isolation between the two.
Using twisted/shielded wire will reduce electrical noise induced onto the power supply cables.
Power supplies are to be adequately regulated and sufficiently low noise to meet the application requirements.
3.3 Analog Section
3.3.1 Analog Input Buffers
The analog input signal connections to the input buffers are made at the IN_A and IN_B connectors, as
specified in Table 2.
Table 2. Analog Input Connections
Analog Input
Channel
IN_A J10 -2.048 V to +2.048 V 50 Ohms
IN_B J11 -2.048 V to +2.048 V 50 Ohms
Connection
Input Signal
Voltage Range I mpedance
There are two analog input channels on the evaluation board. Each analog input channel consists of a
low-noise amplifier configured as a unity gain non-inverting buffer. The buffers utilize a Cirrus Logic
CS3004 precision, low-noise, low-voltage, dual opamp.. These op-amps enable both the inputs and outputs of the analog input buffer to operate virtually rail to rail. The channel input impedance is 50 Ohms.
6 DS768DB4
CDB5571
The analog inputs are designed for connections to single-ended input signals referenced to ground. The
usable input voltage range is -2.048 V to +2.048 V. The theoretical input frequency range of the CS5571
is from DC to the Nyquist frequency of 50 kHz. The analog input buffer amplifiers are configured for a cutoff frequency of 16.8 kHz to band-limit noise into the ADC. Changing the cutoff frequency will change the
noise bandwidth accordingly.
3.3.2 Multiplexer
Analog input channel selection is controlled through the multiplexer. The multiplexer is configured with a
pull-down resistor on the MUX control line to enable input channel labeled "INPUT A" by default. To select
channel B, apply 3.3 V to the multiplexer input control line (MUX).
Signal levels for controlling the multiplexer that selects between analog input channels A and B is shown
in Table 3.
Table 3. Analog Input Channel Selection
Multiplexer
Control Input (MUX)
0V A
3.3 V B
Input Channel
Enabled
During multiplexing, the maximum sample rate for each channel is half that of the ADC’s maximum sample rate. Additionally, the Nyquist frequency for each channel is half of the ADC’s Nyquist frequency.
3.3.3 ADC Reset
The CS5571 ADC makes use of an externally generated power-on reset. Therefore, after power is applied to the ADC, the reset pin must be driven low then released. Pressing the Reset button generates a
reset cycle. A reset cycle can be generated at any time during ADC operation. The ADC RST
pin (active
low) is held inactive through a pull-up resistor.
3.3.4 Voltage Reference
The voltage reference IC provided generates a 4.096 V precision reference.
3.3.5 ADC Reference Frequency
The reference frequency for the CS5571 ADC is provided by a 16.000 MHz oscillator.
DS768DB4 7
CDB5571
3.4 Digital Section
3.4.1 Hardware Configuration
The CDB5571 evaluation board hardware comes pre-configured so the only connection required between
it and a data acquisition system is the serial port connection.
The hardware setup is reconfigurable through the hardware control interface connectors. Configure the
evaluation board by setting the appropriate control line to the appropriate logic level.
Table 4. Hardware Configuration Signals
Function Default Level Label Connector Test Point
Input Channel Select IN_A = Selected (Low) MUX J6, Pin 16 J3, Pin 2
Analog Input Buffers Buffers = Enabled (High) BUFEN J1 J3, Pin1
Serial Port Mode Sync. Self Clock = Enabled (High) SMODE J6, Pin 12 J3, Pin 3
Data Ready Flag Data Ready When Set (Low) RDY
Reset Reset = Inactive (High) RST
Bipolar / Unipolar Mode Bipolar = Enabled (High) BP / UP J6, Pin 2 J3, Pin 8
Digital Filter Dither Dither = Enabled (High) DITHER J6, Pin 4 J3, Pin 9
Serial Port Communication Chip Select = Enabled (Low) CS
Data Conversion Mode Continuous Conversion = Active (Low) CONV J8, Pin 12 E21
J8, Pin 10 J3, Pin 4
J6, Pin 6; S1 J3, Pin 6
J8, Pin 2 E23
3.4.2 SPI™ Serial Port Communications
The CS5571 ADC communications port features an SPI™ serial port. It can be configured for SSC mode
(Master) or SEC mode (Slave) mode as shown in Table 4. Test points are provided to monitor serial communications.
Connections to the serial interface are made according to the following table.
Table 5. Serial Interface Connections
Function Label Connector Test Point
Chip Select CS J8, Pin 2 E23
Serial Data Input SDI J8, Pin 4 E24
Serial Data Output SDO J8, Pin 6 E25
Serial Clock SCLK J8, Pin 8 E26
8 DS768DB4
Loading...