Circontrol CCL-WB2M-SMART series, CCL-WB2M-SMART TRI series, CCL-WB MIX-SMART series, CCL-WB MIX-SMART TRI series Instruction Manual

INSTRUCTION MANUAL

MODELS:

(*)

3G models also included

CCL-WB2M-SMART*
CCL-WB2M-SMART TRI*
CCL-WB MIX-SMART*
CCL-WB MIX-SMART TRI*

WALLBOX SMART Instruction manual

This document is copyrighted, 2013 by Circontrol, S.A. All rights are reserved.
Circontrol, S.A. reserves the right to make improvements to the products
described in this manual at any time without notice.

No part of this manual may be reproduced, copied, translated or transmitted in
any form or by any means without the prior written permission of the original
manufacturer. Information provided in this manual is intended to be accurate
and reliable. However, the original manufacturer assumes no responsibility for
its use, or for any infringements upon the rights of third parties that may result
from its use.
All other product names or trademarks are properties of their respective
owners.

V1.0, April edition 2013

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

CONTENTS

1 INTRODUCTION ................................................................................................................... 3

1.1 IMPORTANT SAFETY INFORMATION ........................................................................ 3

1.2 DESCRIPTION .............................................................................................................. 3

2 FEATURES ........................................................................................................................... 4

3 INSTRUCTIONS FOR USE .................................................................................................. 5

3.1 START RECHARGING PROCEDURE.......................................................................... 5

3.1.1 DISPLAY INFORMATION WHILE CHARGING .................................................... 7

3.2 STOP RECHARGING PROCEDURE ............................................................................ 8

3.2.1 DISPLAY INFORMATION WHEN RECHARGING ENDS .................................. 10

4 ETHERNET COMMUNICATIONS ...................................................................................... 11

4.1 PREREQUISITES ....................................................................................................... 11

4.2 NETWORK TOPOLOGY ............................................................................................. 12

4.3 STEP BY STEP LAN CONNECTION PROCEDURE .................................................. 13

4.4 SETUP WEB PAGE ..................................................................................................... 17

4.4.1 NETWORK SETUP ............................................................................................. 18

4.4.2 MODEM SETUP (only for 3G series) .................................................................. 18

4.4.3 PUBLIC ADDRESS MANAGER .......................................................................... 19

4.4.4 LOCALE SETUP ................................................................................................. 20

4.4.5 TIME SETUP ....................................................................................................... 20

4.4.6 DYNAMIC DNS SETUP ...................................................................................... 21

4.4.7 SECURITY SETUP ............................................................................................. 22

4.4.8 SYSTEM INFORMATION.................................................................................... 23

4.5 OTHER URL CONFIGURATION ................................................................................. 25

4.5.1 LOG WEB PAGE ................................................................................................. 25

4.5.2 MODEM STATUS (FOR 3G MODELS) .............................................................. 26

5 3G COMMUNICATIONS (FOR 3G MODELS) ................................................................... 27

5.1 STEP BY STEP CONFIGURATION ............................................................................ 27

6 CHARGE POINT OCPP INTEGRATION ............................................................................ 30

6.1 INTEGRATION SETUP WEB PAGE ........................................................................... 30

6.2 OCPP ENGINE SETUP WEB PAGE ........................................................................... 31

6.2.1 APPLICATION PARAMETERS ........................................................................... 32

6.2.2 POWERSTUDIO ENGINE................................................................................... 33

6.2.3 CHARGE BOX (CB) ............................................................................................ 34

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

6.2.4 OCPP SETTINGS ............................................................................................... 35

6.2.5 MANAGEMENT SYSTEM (CS) .......................................................................... 36

6.2.6 SSL CERTIFICATES ........................................................................................... 37

6.2.7 ACTIONS ............................................................................................................. 37

6.3 STEP BY STEP INTEGRATIONS PROCEDURE ....................................................... 38

7 URL SUMMARY TABLE .................................................................................................... 41

8 CHARGE STATION MONITORING .................................................................................... 42

8.1 USING CIRCARLIFE CLIENT ..................................................................................... 42

8.2 USING WEB BROWSER ............................................................................................. 43

9 CIRCARLIFE SCADA CLIENT ........................................................................................... 44

9.1 MENU BAR .................................................................................................................. 45

9.1.1 OPTIONS MENU ................................................................................................. 45

9.1.2 VIEWS MENU ..................................................................................................... 46

9.1.3 GENERAL MENU ................................................................................................ 47

9.2 TOOLBAR ................................................................................................................... 48

9.2.1 TOOLBAR SETUP MENU ................................................................................... 48

9.3 STATUS BAR .............................................................................................................. 49

9.4 SCADA GRAPHS ........................................................................................................ 50

9.4.1 GRAPHS TOOLBAR ........................................................................................... 52

9.5 SCADA TABLES .......................................................................................................... 53

9.5.1 TABLE PROPERTIES ......................................................................................... 54

9.6 NOTIFIED EVENTS..................................................................................................... 55

10 CCL1 ENGINE .................................................................................................................... 56

10.1 BOLLARD STATE SECTION ...................................................................................... 57

10.2 PLUGS SECTION ........................................................................................................ 58

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

1 INTRODUCTION

This manual contains all the information necessary for safe use of the electrical vehicle
charger and will help you get the best performance results from it.

This equipment incorporates the latest technology and offers the most advanced
service on the market in the area of EV chargers.

1.1 IMPORTANT SAFETY INFORMATION

 Read all the instructions before using and install this product.
 Do not use cables there are not in perfect conditions.
 Do not use this unit for anything other than electric vehicle charging.
 Do not modify this unit. If modified, Circontrol will reject all responsibility and the

warranty will be void.

 Comply strictly with current safety regulations according to your country rules.
 Do not make repairs or manipulations with the unit energised.
 Only trained and qualified personnel should have access to low-voltage

electrical parts inside the device.

 Check the installation annually by qualified technician.
 Remove from service any item that has a fault that could be dangerous for

users (broken plugs, caps that don’t close...).

 Use only original supplied spare parts.
 Do not use this product if the enclosure or the EV connector is broken, cracked,

open, or shows any other indication of damage.

1.2 DESCRIPTION

Smart post charging solution is special designed to charge EV using standardized
MODE 1 and MODE 3 according to European standard IEC_61851-1.

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

2 FEATURES

 Display: Two lines character display provide to user information of the charge

and detailed data as kWh and duration time.

 Connector Lock: Type 2 connector has a lock system to avoid disconnection

of EV meanwhile is charging.

 Light beacon: Three colour led indicates to user status of the wall mount unit.
 RFID: Authentication and Prepayment options.
 Ethernet: TCP/IP communication over an “Ethernet” compliant network

between the Wall mount and customer network is available.

 3G and GPRS (optional) for remote control or OCPP integrations.
 Energy metering: Integrated meter built is measuring power and energy

consumed by the EV during a charge.

 Real time monitoring: Using standard browser system allows access to the

unit and monitoring charge status.

 Remote control: Remote actions as start/stop charge are available.
 Charge data storage: System is capable to generate graphics and reports

according to data storage from recharging historic.

 OCPP integration: Standard communication protocol between charge points.

Allows charging stations connecting with central system allowing centralized
authentication, user authorization in real time and a wide variety of functions
related to recharge.

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

3 INSTRUCTIONS FOR USE

3.1 START RECHARGING PROCEDURE

Wallbox has two status led indicators for
each outlet. Green light means there is at
least one outlet available and ready to
start a recharge.

 Present a RFID card to the right side

of the WallBox unit.

 Wait until the display shows the

following message:

 Plug the cable into your car.
 Choose one available socket in the

WallBox mount unit

 Connect your cable to the unit.

Choose your plug

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

 Led Status indicator of the plug

connected changes to yellow.

 Display shows the following

message:

 System will lock the plug

automatically.

 If vehicle is not ready to charge,

this status will be permanent.

 When vehicle is ready to charge led

status indicator of the plug
connected will change from yellow to
blue.

 WallBox starts recharging.
 On display shows the following

information:

 Charge time
 Real time consumed energy

PLUG A: Starting

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

3.1.1 DISPLAY INFORMATION WHILE CHARGING

The display shows in scroll mode following messages when an EV is charging:

Plug A status

Real time consumed Energy of Plug A

Plug B status

Plug A recharging elapsed time

Show card

(Only if there is an available plug)

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

3.2 STOP RECHARGING PROCEDURE

Wallbox has two status led indicators for
each outlet:

 Blue light means there is one outlet

busy and recharging an electric
vehicle.

 Green light means there is at least

one outlet available and ready to start
a recharge.

 Present a RFID card to the right side

of the WallBox unit for 3 seconds.

 Led status indicator of the plug

connected change from blue to
green.

 On display shows the following

information:

IMPORTANT

For STOP recharging present same card that
was used for start recharge.

PLUG A: Disconnect the

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

 First, remove your cable from the

unit.

 Remove cable from your vehicle.

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

3.2.1 DISPLAY INFORMATION WHEN RECHARGING ENDS

The display shows in scroll mode following messages as a data summary when charge
ending.

Plug A recharging elapsed time

Total consumed Energy of Plug A

Show card

(Only if there is an available plug)

Total cost of recharging the vehicle

(Free = prepayment disabled)

Total cost of recharging the vehicle

Indicates Plug A has to be disconnected.

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

4 ETHERNET COMMUNICATIONS

Charge station can be configured and monitorized to establish owner preferences or
specific setup using integrated Ethernet communication port allocated in main
controller CCL1 device.

Once service PC is configured as bellow procedure and connection established with
the charge station, direct access to the device main setup page will be showed.

Charge station is shipped from the factory with default network setting of “DHCP
enabled”. It means that the charge station will try to obtain an IP address from a DHCP
server available on the network.

Step by step below guide detailed setup an IP address to the charging station in case
there is no DHCP server available on the network.

4.1 PREREQUISITES

Below table shows, hardware and software needed to setup and IP address to the
charge station.

Computer running one of the following

operating systems

- Windows XP (x86)

- Windows Vista (x86/x64)

- Windows 7 (x86/x64)

- Windows 8 (x86/x64)

Crossover Cable UTP Cat.5e or Cat6

Software needed: IPSetup.exe.

(Supplied by Circontrol)

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

4.2 NETWORK TOPOLOGY

Connecting pc with charge station needs to be done with static IP address and TCP/IP
v4 protocol. Next section shows how to do this configuration.

Below figure shows Ethernet connection topology and the IP addresses used in this
guide as example.

IP: 192.168.1.11
NETMASK: 255.255.255.0

IP: 192.168.1.10
NETMASK: 255.255.255.0

Crossover UTP

cable

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

4.3 STEP BY STEP LAN CONNECTION PROCEDURE

This section provides a step-by-step guide to be able to connect a laptop to the charge
station in order to see real-time status.

Step

Actions

1

Click on the network icon next to the clock of the taskbar.

Click on “Open Network and Sharing Center”

2

On the left pane, click the option: “Change adapter settings”.

3

Right click on “Local Area Connection” and then click on “Properties”

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

4

Select “Internet Protocol Version 4 (TCP/IP)” option and click “Properties”.

5

Setup IP address and subnet mask like as shown below:

Click OK twice to complete the process to assigning IP address to the
computer.

EXAMPLE

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

7

Execute IPSetup.exe utility.

8

Enter the following parameters:

 MAC of the CCL1 device (see lateral label in the device)
 IP address: i.e.(192.168.1.11)
 Netmask: i.e. (255.255.255.0)
 Gateway: leave default settings.

10

Wait 30 seconds approximately until the process is complete.

EXAMPLE

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

11

The process will complete when the following message appears.

If the message shown is the next one, check the following parameters.

- Check IP address entered.

- Check the MAC of the device entered.

- Try with another UTP CAT5e cable.

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

4.4 SETUP WEB PAGE

Setup web page allows managing networking setup, modem 3G setup, upgrading the
device and other options.

To access to the setup web page, open a web browser and enter the following
address:

NOTE: Remember to remove the quotes when entering an address into the web browser.

Direct link: http://”IP_ADDRESS”/html/setup.html

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

4.4.1 NETWORK SETUP

This section provides basic configuration of the network parameters.

Value

Description

Host name

Name of the device on the network

DHCP

Enable or disable the IP address assignment
by a DHCP server.

DHCP Client ID

Client ID associated to the DHCP Server (If
available)

Address

IP address assigned to the charge point

Netmask

Netmask of the network

4.4.2 MODEM SETUP (only for 3G series)

Devices with 3G modem integrated on the unit can enter on this section the parameters
of the modem provided by the mobile network operator.

Value

Description

APN

Access point name for mobile communications

User

Parameters assigned to the APN.

Password

Reset timer (hours)

Timer to reset the modem and mobile

communications

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

4.4.3 PUBLIC ADDRESS MANAGER

This section is only for OCPP integrations and allows setting the IP address to
establish connection between charge point and OCPP central system.

Value

Description

Address type

 Local address: When selected, private IP address will be

sent to OCPP central system. This option is valid if the
OCPP central system is connected to the same private
network of the charge point.

 Static address: When selected, enter a value on Public IP

textbox (IP address or a domain name).

 SIERRA Wireless Raven XE H2295EW: Select this option

only when SIERRA Wireless RAVEN XE router 3G is
connected on the network.

 TELIT HE863: Select this option only on 3G charge points

models where modem is integrated on the CCL1 device.

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

4.4.4 LOCALE SETUP

This section allows changing the language on the LCD screen.

Value

Description

Language

Allows selecting the unit language using a
dropdown.

4.4.5 TIME SETUP

This section allows setting the time and region unit time.

Value

Description

Primary NTP Server

Allows to synchronize the time through
internet automatically

Secondary NTP Server

Time zone

Allows selecting the regional unit time using
a dropdown.

Time

Actual date and time of the unit.

Time and date synchronization of the charge
point from computer connected.

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

4.4.6 DYNAMIC DNS SETUP

Dynamic DNS is a system that updates in real-time the public IP address assigned to a
domain name server.

Value

Description

Server

Allows selecting the type of Dynamic DNS Server using a
dropdown.

Hostname

Parameters provided by dynamic DNS server.

User

Password

Server

Port

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

4.4.7 SECURITY SETUP

All of these parameters are disabled by default. When enabled, it denies unauthorized
access to the web page configuration (setup.html) of the device and also prevents the
export or import of a new configuration of PowerStudio engine from an unauthorized
user.

Value

Description

Password

ON: authentication enabled
OFF: authentication disabled

Username

Username and password authentication for setup.html web
page.

New password

Password

Do not forget the credentials of the device. There is no way to reset the
device to default factory settings.

It will require returning the unit to the service centre.

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

4.4.8 SYSTEM INFORMATION

This section provides basically information about the unit.

Value

Description

MAC

Identifier of the network card of the unit

Version Upgrade

Version of the firmware currently installed
and link to the upgrade web page

Powerstudio version

Engine version of PowerStudio

Devices status

Link that allows viewing the status of the
configured devices.

4.4.8.1 SYSTEM UPGRADE

Upgrade web page allows to upgrade the firmware of the unit through a file with
*.upgrade extension.

This file is provided by your installer or manufacturer of the unit.

NOTE: Remember to remove the quotes when entering an address into the web browser.

Direct link: http://”IP_ADDRESS”/html/upgrade.html

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

4.4.8.2 POWERSTUDIO VERSION WEB PAGE

Powerstudio version web page allows viewing the following information:

 Current firmware version installed.
 Scada Platform version
 Available languages
 List of available driver devices that can communicate with the charge point.

NOTE: Remember to remove the quotes when entering an address into the web browser.

NOTE: it is reserved the right to change without notice the drivers on future firmware versions of

the charge point.

Firmware file transfer must not be interrupted. Failure of the file transfer
involves irreversible damage to CCL1 master controller and the correct
functionality of the equipment. It will require returning the unit to the service
centre.

Ensure that the unit will not be affected or powered off while updating.

Direct link: http://”IP_ADDRESS”/services/system/info.html

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

4.4.8.3 DEVICES STATUS WEB PAGE

Devices status web page allows checking if all devices configured with CirCarLife
Scada Editor 4.0 Software are available and working properly.

NOTE: Remember to remove the quotes when entering an address into the web browser.

4.5 OTHER URL CONFIGURATION

There are more useful web pages installed on the master device. This section shows
the purpose of these web pages and how to access them.

4.5.1 LOG WEB PAGE

Log web page is a log that is created since charge point is powered ON. If charge point
is restarted this log is erased and immediately is created a new one.

These logs are not recorded and no way to consult older logs if the charge point has
shutdown before.

NOTE: Remember to remove the quotes when entering an address into the web browser.

Direct link: http://”IP_ADDRESS”/html/devstat.html

Direct link: http://”IP_ADDRESS”/html/log

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

4.5.2 MODEM STATUS (FOR 3G MODELS)

This website allows seeing real-time status of 3G connection.

NOTE: Remember to remove the quotes when entering an address into the web browser.

Value

Description

Connection

 3G communications status.
 Data access protocol used.
 Cell phone signal and coverage.

IP address

Public IP assigned to the charge point.

4.5.2.1 SIGNAL LEVEL TABLE

Following table shows some possible values of the integrated modem on the charge
point.

SIGNAL

DESCRIPTION

More than -80dBm

Good signal

Between -80dBm and -90dBm

Moderate signal

Less than -90dBm

Poor signal

Direct link: http://”IP_ADDRESS”/html/modem-status.html

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

5 3G COMMUNICATIONS (FOR 3G MODELS)

Once SIM card is inserted on CCL1 device, following parameters must be known in
order to set up 3G communications and Internet access:

 APN (Access Point Name)
 User
 Password

These parameters have to be provided by your mobile network operator of the SIM
card inserted.

5.1 STEP BY STEP CONFIGURATION

Step by step bellow shows how to configure the 3G communications service.

Step

Action

1

Open web browser and go to: http://”IP_ADDRESS”/html/setup.html

2

Locate Modem Setup section

3

Enter following parameters (Provided by your mobile network operator)

 APN
 User
 Password

4

Click on Save Setup

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

5

Go to following address: http://”IP_ADDRESS”/html/modem-status.html
It is required to enter PIN number the first time that SIM card is inserted into

CCL1 device.

Enter SIM PIN and click on Confirm button.

6

After entering pin number, it shows following message:

Wait a few seconds until modem is connected on the network.

7

When the 3G connection is successful, following message will appear on the
web page of modem status.

PIN number will not be required anymore after entering for the first time

and the device will start 3G communications automatically.

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

 Connection: Indicates the connection status and the type of connection

established.

 IP address: Public IP assigned by your mobile network operator

8

OPTIONAL STEP

Finally, it is recommendable to setup parameters of Dynamic DNS for update in
real-time the public IP address assigned to a domain name.

Dynamic DNS parameters can be introduced in setup web page.

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

6 CHARGE POINT OCPP INTEGRATION

6.1 INTEGRATION SETUP WEB PAGE

Integrations setup web page allows managing and enables the integrations available
on the dropdown list.

To access to the setup web page, open a web browser and enter the following
address:

NOTE: Remember to remove the quotes when entering an address into the web browser.

The selected default option is: none.
When this option is set to none, there is no integration enabled on the charge point. In

this way, all RFID showed can start a rechargement.

Available options:

- OCPP 1.2: Open Charge Point Protocol (OCPP) is an open protocol between
charging stations and managing central system.

Direct link: http://”IP ADDRESS”:65432

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

6.2 OCPP ENGINE SETUP WEB PAGE

This website allows to setup parameters of the integration selected on the previous
section.

First time is running OCCP engine on the charge point, it starts as configuration mode
and all fields are empty. The data is always saved even when the charge point is
powered off or even the OCPP engine is stopped.

To access to the OCCP engine setup web page, open a web browser and enter the
following address:

NOTE: Remember to remove the quotes when entering an address into the web browser.

Direct link: http://”IP ADDRESS”:8080

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

6.2.1 APPLICATION PARAMETERS

This section is for configuring the OCPP engine website. It is recommended leaving the
default settings.

Value

Description

Administration TCP port

Port number where the OCPP engine
website is hosted.

By default: 8080

Administrator

Administrator username.

By default: admin

New admin password

Password for administrator user.

By default: 1234

If a new password is entered, it will be
applied after saving new configuration.

Repeat admin password

8080

admin

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

6.2.2 POWERSTUDIO ENGINE

OCPP Engine is a service running in parallel with PowerStudio and it is required to add
these parameters on this section.

Value

Description

Host URL

URL where PowerStudio is hosted.

By default: http://127.0.0.1

Port

PowerStudio port. By default: 80

User – System level

Username and password authentication
configured on PowerStudio.

Default factory parameters:

Username: admin

Password: 1234

Password

User – Edit level

Username and password configured in
the security section of setup.html website.

Default factory parameters:

Username: anonymous

Password: anonymous

Password

http://127.0.0.1

80

admin

1234

anonymous

anonymous

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

6.2.3 CHARGE BOX (CB)

All of the parameters shown below must be assigned by OCPP central system
administrator.

Please contact to your OCPP central system administrator to get the configuration
parameters.

Value

Description

Charge Box ID

Charge point identifier

Protocol

Protocol type. If HTTPS is selected,
make sure to have CS Server CA
certificate.

OCPP Listening port (internal)

Listening port from charge point. Make
sure the ports configured are opened on
the gateway.

OCPP Listening port (public)

User (for the CB server)

Authentication parameters.

New password

Repeat password

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

6.2.4 OCPP SETTINGS

Select properly values according to OCPP central system parameters. Please contact
to your administrator to select the correct values.

Value

Description

Use local white-list

Yes: store a list of authorised users on
the charge point.

No: Authorization is consulted for each
RFID card shown.

Use OCPP time synchronization

Time synchronization between charge
point and OCPP central system.

Compress OCPP messages

Sending compressed messages between
charge point and central system.

NOTE: Before enabling this option
consult to your OCPP administrator if
central system allows this function.

Energy for Start/Stop transaction

Partial: Send partial energy consumption
while vehicle is charging.

Total: Send total energy values of
energy meter.

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

Stop charge if StartTransaction rejects the

user

Set this option according to your central
system.

Heartbeat interval

Heartbeat send interval (in seconds) for
the back-end system.

Connection timeout

Timeout (in seconds) before connecting
to the central system.

Meter value sample interval

Meter value sample send interval (in
seconds) for the back-end system.

NOTE: Put 0 seconds to send meter
values only when charge point starts or
stops charging a vehicle.

6.2.5 MANAGEMENT SYSTEM (CS)

This section provides to the charge point where OCPP central system is located and if
it is requires authentication.

Please contact to your OCPP central system administrator to get the configuration
parameters.

Value

Description

Host URL

Address where OCPP central system is
located

User

Authentication for central system.

Password

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

6.2.6 SSL CERTIFICATES

Secure Sockets Layer (SSL) provides authentication and privacy of information
between charge point and central system on Internet. Consult your OCCP central
system administrator for the CS Server certificate.

Value

Description

CS Server CA certificate

Central System file certificate supplied by
your central system administrator.

CB Server CA certificate

Upload charge box file certificate
supplied with charge point unit.

6.2.7 ACTIONS

Final options to complete the OCCP engine configuration.

Value

Description

Save settings and apply.

Restore data entered.

Import using a configuration XML file.

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

6.3 STEP BY STEP INTEGRATIONS PROCEDURE

Step

Action

1

Open web browser and enter following address:

This page allows selecting and enabling the integration type on the CCL1
device.

2

By default, there is no integration configured on the CCL1.

Select desired integration and click on Save setup button.

4

Enter a new address on the web browser:

This page allows setup the integration enabled in previous steps.

5

Fill the blank fields following parameters as your central system administrator.
Click on Save setup to confirm.

Direct link: http://”IP ADDRESS”:65432/

Direct link: http://”IP ADDRESS”:8080/

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

7

Enter a new address on the web browser:

Locate Public address Manager section shown as below:

The selected default option is: Local address

 To configure CCL1 3G series go to next step.
 To configure CCL1 without 3G connectivity go to step number 9.

8

This step is only for CCL1 3G series.

Change address type from “Local address” to “TELIT HE863” on Public
address Manager section inside Setup web page.

To finish go to step 10.

Direct link: http://”IP_ADDRESS”/html/setup.html

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

9

This step is only for CCL1 or other devices without 3G connectivity.

1. Change address type from “Local address” to “Static address” on
Public address Manager section inside Setup web page.

2. Enter Public IP address or a domain name.

To finish go to next step.

10

Click on Save setup to confirm.

Wait a few seconds until CCL1 restarts.

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

7 URL SUMMARY TABLE

Following table shows a summary of the entire URL available as described in previous
sections.

DESCRIPTION

URL

Setup

http://”IP_ADDRESS”/html/setup.html

Upgrade

http://”IP_ADDRESS”/html/upgrade.html

PowerStudio version

http://”IP_ADDRESS”/services/system/info.html

Devices status

http://”IP_ADDRESS”/html/devstat.html

Log

http://”IP_ADDRESS”/html/log

Modem status

http://”IP_ADDRESS”/html/modem-status.html

Integration enable/disable

http://”IP_ADDRESS”:65432

Integration engine configuration

http://”IP_ADDRESS”:8080

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

8 CHARGE STATION MONITORING

The IP address assigned in last section it will be useful to connect to the charge station
to monitor the real-time status.

Exist two ways to connect to the charge station:

- CirCarLife client software. (Supplied by Circontrol)

- Internet web browser.

8.1 USING CIRCARLIFE CLIENT

Step

Action

1

Execute CirCarLife Client software.

2

Go to: General -> Connect

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

3

Enter IP address and port shown in the last example.

- IP address:

- Port: 80

Click OK to connect to the charge point.

8.2 USING WEB BROWSER

It is needed to have installed the latest version of java to access to the monitoring
page. Download it from: www.java.com

Step

Action

1

Execute your web browser and enter the following address:
i.e.(http://IP_ADRESS) (monitor page will open automatically)

2

Wait while the client software is starting.

EXAMPLE

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

9 CIRCARLIFE SCADA CLIENT

CirCarLife Scada client software allows displaying and reporting all parameters
generated by devices connected to the engine of the charge point.

Client platform is implemented in Java and can be executed on many devices.

Devices connected to the charge point may vary depending on model purchased.

CirCarLife Scada client is divided on 4 sections:

1. Menu bar

2. Toolbar

3. Screen information

4. Status bar

Following section describes in detail each of the points mentioned above.

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

9.1 MENU BAR

Menu bar is located at the top and provides access to all available client features.
There are three main menus, "Options", "Views" and "General".

9.1.1 OPTIONS MENU

Option

Description

Properties

Displays properties of the currently active view. This option
can be active or not depending on the view in progress.

Print

Print currently active view. This option can be active or not
depending on the view in progress.

Export

Exports currently active view. This option can be active or
not depending on the view in progress.

Exit

Close the client software.

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

9.1.2 VIEWS MENU

Option

Description

Previous

Displays the previous view.

Next

Displays the next view (If available).

Historic

Displays any view previously consulted.

Study

Displays graph and tables views.

Devices

Device list shortcut.

Events

Displays the events log or the active events window.

Device status

Display the general status of all connected devices.

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

9.1.3 GENERAL MENU

Option

Description

Toolbar

Displays or hides the toolbar.

Statusbar

Displays or hides the status bar.

Alarm if it not
communicate

Audible alarm if communication is lost between charge
point and computer connected.

Events actions

List of actions enabled in the client software.

Connect

Connects with another CirCarLife Engine.

Logout

Closes the current session. Only available when the user
has connected to engine that requires authentication.

Language

Changes the client application language.

Look and feel

Changes the appearance of the client application (Skin).

Graphs properties

Changes graph appearance.

About

Displays client application information.

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

9.2 TOOLBAR

Toolbar contains the most frequent options used in the client software.

Option

Description

Previous

Displays the previous view.

Next

Displays the next view. If available.

Down arrow

Displays any view previously consulted.

Devices

Device list shortcut.

Graph

Creates a graph.

Table

Creates a table.

Events

Displays event history

Properties

Displays the properties window of the current view.

Print

Allows us to print the current view.

9.2.1 TOOLBAR SETUP MENU

It is possible to hide or display buttons for the toolbar. Right-click on the toolbar and
following setup menu appears:

NOTE: The toolbar may be hidden using the “General” menu. The menu bar may be hidden

using the “Enable menu and toolbar” option in the editor “Preferences”. Using this latter method
it will not be possible to make it appear again from the client application.

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

9.3 STATUS BAR

Status bar is located at the bottom of the client software and it contains general
information about status of CirCarLife Scada engine connected.

OVERVIEW

Status

Description

Online CirCarLife Scada engine and
working properly.

Offline CirCarLife Scada engine.

Incidences

Description

One or more devices are not
communicating.

See device status section to find witch
device is not communicating.

One or more devices are not reporting.

One or more events are active.

 Double-click over icon showed to see details.

NOTE: Status bar can be hidden using the "General” option in the client application menu. It

may also be hidden using the “Enable menu and toolbar” option in editor “Preferences”. In the

latter case it will not be possible to make it appear again from the client application.

Engine status

Engine name, IP and port

Incidences

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

9.4 SCADA GRAPHS

One of the most powerful tools of client software is graphs tools of the devices.
Following image shows variables selection window under CCL1Engine where it is

possible to select Plug A and Plug B on the charge point.

At first it appears the available plugs from the charge station. Select the desired plug to
proceed with the creation of the graph.

The system automatically chooses the representation period and the grouping of data,
which can obviously be changed later.

Default parameters should be displayed as a week and the time period is typically 30
minutes.

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

Picture bellow shows the aspect of the graph generated by the client software.

Graph tool has following sections:

 Title: Situated on the upper area. It is a text describing the represented

variables.

 Representation areas: Data represented by bars for energy or by lines for

power. Each area contains some common characteristics:

- Key: Provides general information about the variables that are
represented in the area.

- Y-Axis: Provides information on the units of the variables that are
represented in this axis and the range of values that are being
displayed.

- X-axis: Typically, this is the time axis and is located at the bottom of the
representation area. Here the time interval being represented may be
seen. Usually predefined time intervals are represented (day, month,
etc.). But the user can choose the most suitable as can be seen later.

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

- Drawing area: Contains the actual figure representing the variables of
the area in question. There is a drawing area for each area of
representation.

 Graph toolbar: Contains a series of actions that can be performed on the

graph. Depending on the type of graph it will contain more or fewer options.

9.4.1 GRAPHS TOOLBAR

Graphs always have a toolbar at the bottom of the window that allows different actions
related to the data represented.

Option

Description

Back

Displays the previous interval of data.

Next

Displays the next interval of data.

Go to

Allows choosing a closed graph interval.

Grouped by

Allows choosing standard graph interval by day, week,
month or year.

Period

Sampling period variables.

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

9.5 SCADA TABLES

Another important client tool is Scada table tool.
First, it is necessary to choose the device to display its recorded variables and click on

table button option.
Once table button is pressed, a discriminator window appears:

CCL1Engine has two types of tables:

- Standard: sampling variable (energy, power, voltage) depending on the
meter installed on the charge point.

- Charge: summary of recharges on the charge point.

Following image shows the appearance of table recharges:

Table tool has following sections:

 Title: data period displayed.
 Body: it contains a series of columns with the values registered.
 Toolbar: personalization data showed in the table.

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

Table toolbar has same options and functionality as explained on toolbar graphs
section.

9.5.1 TABLE PROPERTIES

It is possible to configure some aspects using the table “Properties” option. This option
can be accessed using the “Options” menu, “Properties” submenu, or directly with the
“Properties” button on the main toolbar.

Table properties window

Using this option it is possible to add new variables to the table in the same way as
they are added to the graph, by clicking on “Add”.

It is also possible to delete variables from the table selecting the desired variables and
clicking on the “Delete” button.

User can print the current graph displayed using “Print” option on the “Options” menu of
the main menu or the “Print” button of the upper toolbar.

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

9.6 NOTIFIED EVENTS

CirCarLife Scada client enables current events to be viewed in real time, both the
simple events that are active as well as those that must also be acknowledged by the
user.

Events not requiring user acknowledgement are displayed in a pop-up window, which
may be accessed via the “Views” menu option, then “Events” and finally “Active events”
or directly from the status bar by clicking on the icon indicating there are active events
in the system.

Notified events window

Note that an event with an acknowledgement date and a deactivation date will
disappear from the list of events reported.

This window allows event acknowledgement. Select from the events to be
acknowledged from the events list and click the “Recognize events” button at the
bottom. The event acknowledgement date is shown. When an event is disabled it will
disappear from the list. If a previously acknowledge event is acknowledged again the
operation will not produce any effect.

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

10 CCL1 ENGINE

CCL1 engine is the application of recharging Wallbox Smart and it is showed as a main
screen when CirCarLife Scada client is connected on the CCL1 device.

Following image shows the aspect of the charge point engine:

The engine is divided on two sections:

- Bollard state: describes general state of the charge point.

- Plug status: plug status and other useful information.

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

10.1 BOLLARD STATE SECTION

This section describes the general state of charge point.

Any of these options may not appear on the charge point. It depends on the hardware
of the unit purchased or by software configuration.

Status

Leakage

Charge point leakage status

Normal operation

Channel 3 tripped

Tamper switch

Tamper switch status

Normal operation

Rear cover removed

Tilt
(sensor inside CCL1 device)

Charge point tilt status

Normal operation

Charge station tilted

If any of the points mentioned above is in status, charge point will be out of service
(plug A and plug B) until event is resolved.

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

10.2 PLUGS SECTION

This section describes the plug status and other useful information. Each plug looks the
same configuration as shown below:

Following table shows the status of each option showed on plug section.

Description

Status

Plug status

Plug available

Starting

recharge

Plug in use

Fault

Car connected

Vehicle connection status

Car connected

Car not connected

Connector lock

Connector lock status

Locked plug

Unlocked plug

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

Description

Reserved

Reservation status

0 = No reservation

Charge

Starts a charge from remotely point.

Stop charging in progress

Pauses charging in progress.

Enable

Enable or disable the plug.

Leakage

RCD plug status.

Normal operation

Channel 1 or 2 tripped

Charge relay

Indicates contactor status

Voltage is being supplied to
the vehicle.

No voltage is being
supplied to the vehicle.

Active Energy (kWh)

Total charge measured energy

Partial active energy

(kWh)

Partial energy meter of the last charge

Charge request date

Date of the last charge request

Charge begin date

Starting date of the last charge

Charge end date

End date of the last charge

Charge time

Duration of the last charge

Last charge stop

Reason for the last charge stop.

Status: Reserved

CIRCONTROL, S.A. – Innovació, 3 – 08232 – Viladecavalls (Barcelona)

Tel.: [phone] – Fax: [phone]

Web: www.circontrol.com – E-mail: [e-mail]

WALLBOX SMART – INSTRUCTION MANUAL

C / Innovació, 3

Pol. Ind. Can Mitjans

08232 - Viladecavalls

Barcelona - Spain

Tel: [phone]

Fax: [phone]

www.circontrol.com