CipherLab CP60G, CP60, CP60GCE Reference Manual

Download

Windows Embedded Compact 6.0

CP60 / CP60G

Version 1.01

(CE)

PREFACE

COPYRIGHT

is the proprietary information of CIPHERLAB CO., LTD. and its respective legal owners; it is protected by copyright laws and international copyright treaties, as well as other intellectual property laws and treaties, with all rights reserved.

In no event and by no part shall this document be reproduced, stored in a retrieval system, or transmitted in any form or by any means including but not limited to electronic, mechanical, photocopying, and recording without the prior written consent of CIPHERLAB CO., LTD. Any reverse engineering of software is also prohibited.

DISCLAIMER

The information herein is subject to change without notice. The information and the intellectual property herein are confidential between you and CIPHERLAB CO., LTD. and remain the exclusive property of CIPHERLAB CO., LTD. and its respective legal owners. Should you find any problems in this document, please report them to CIPHERLAB in writing. CIPHERLAB does not warrant this document is error-free.

TRADEMARK RECOGNITION

CipherLab logo is a registered trademark of CIPHERLAB CO., LTD. Windows Embedded Compact (Windows CE) is a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries. All other brands, products and services, and trademark names are the property of their registered owners. The editorial use of these names is for identification as well as to the benefit of the owners, with no intention of infringement.

CONTACT

For product consultancy and technical support, please contact CIPHERLAB’s sales representative in your local area. You may also visit CIPHERLAB web site for more information.

CIPHERLAB CO., LTD.

Website:

http://www.CipherLab.com

FOR UNITED STATES

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful int erference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

SAFETY NOTICES

RADIO WAVE EXPOSURE AND SPECIFIC ABSOR PTION R ATE (SAR) INFORMATION

This mobile computer model CP60G has been designed to comply with applicable safety requirements for exposure to radio waves. These requirements are based on scientific guidelines that include safety margins designed to assure the safety of all persons, regardless of age and health.

The radio wave exposure guidelines employ a unit of measurement known as the Specific Absorption Rate, or SAR. Tests for SAR are conducted usi ng standardized methods with the phone transmitting at its highest certified power level in all used frequency bands.

While there may be differences between the SAR levels of various phone models, they are all designed to meet the relevant guidelines for exposure to radio waves. SAR data information for residents in countries that have adopted the SAR limit recommended by the International Commission of Non-Ionizing Radiation Protection (ICNIRP), which is 2 W/kg av eraged over ten (10) gram of tissue (for example European Union, Brazil and Australia):

The highest SAR value for this model phone when tested by CIPHERLAB for use at the body is 1.35 W/kg (10g).

FOR UNITED STATES

THESE PRODUCT MODELS HAVE BEEN CERTIFIED IN COMPLIANCE WITH THE GOVERNMENT’S REQUIREMENTS FOR EXPOSURE TO RADIO WAVES.

The CP60 series mobile computer has been designed to comply with applicable safety requirements for exposure to radio waves. Your mobile computer is a radio transmitter and receiver. It is designed to not exceed the limits* of exposure to radio frequency (RF) energy set by governmental authorities. These limits establish permitted levels of RF energy for the general population. The guidelines are based on standards that were developed by international scientific organizations through pe riodic and thorough evaluation of scientific studies. The standards include a safety margin designed to assure the safety of all individuals, regardless of age and health.

The radio wave exposure guidelines employ a unit of measurement known as the Specific Absorption Rate (SAR). Tests for SAR are conducted using standardized methods with the product transmitting at its highest certified power level in all used fr equency bands. While there may be differences between the SAR levels of various product models, they are all designed to meet the relevant guidelines for exposure to radio waves.

The highest reported SAR values for body-worn accessory and simultaneous transmission are 0.76W/kg, and 1.27W/kg respectively for CP60G. The highest reported SAR values for body-worn operation are 1.03W/Kg for CP60. For body-worn operation, the product has been tested when positioned a minimum of 15 mm from the body without any metal parts in the vicinity of the product.

Before a WWAN model is available for sale to th e public in the US, it must be tested and certified by the Federal Communications Commission (FCC) that it does not exceed the limit established by the government-adopted requirement for safe exposure*. The tests are performed in positions and locations (i.e., by the ear and worn on the body) as required by the FCC for each model. The FCC has granted an Equipment Authorization for this phone model with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. While there may be differences between the SAR levels of various phones, all mobile phones granted an FCC equipment authorization meet the government requirement for safe exposure. SAR information on this phone model is on file at the FCC and can be found under the Display Grant section of FCC ID Q3N-CP60G. Additional information on SAR can be found on the Cellular Telecommunications & Internet Association (CTIA) website at

* In the United States and Canada, the SAR limit for mobile phones used by the public is 1.6

watts/kilogram (W/kg) averaged over one gram of tissue. The standard incorporates a margin of safety to give additional protection for the public and to account for any variations in measurements.

http://www.fcc.gov/oet/fccid after searching on

http://www.phonefacts.net.

FOR PRODUCT WITH LASER

CAUTION

This laser component emits FDA / IEC Class 2 laser light at the exit port. Do not stare into beam.

SAFETY PRECAUTIONS

RISK OF EXPLOSION: IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

 The use of any batteries or charging devices, which are not originally sold or

manufactured by CipherLab, will void your warranty and may cause damage to human body or the product itself.

 DO NOT disassemble, incinerate or short circuit the battery.  DO NOT expose the scanner or the battery to any flammable sources.  For green-environment issue, it's important that batteries should be recycled in a proper

way.

 Under no circumstances, internal components are self-serviceable.  The charging and communication cradle uses an AC power adapter. A socket outlet shall

be installed near the equipment and shall be easily accessible. Make sure there is stable power supply for the mobile computer or its peripherals to operate properly.

CARE & MAINTENANCE

 This mobile computer is intended for industrial use. The mobile computer is rated

IP65/67, however, the mobile computer can get damaged when being exposed to extreme temperatures or soaked wet.

 When the enclosure of the mobile computer gets dirty, use a clean and wet cloth to wipe

off the dust. DO NOT use/mix any bleach or cleaner. Always keep the LCD dry.

 For a liquid crystal display (LCD) or touchscreen, use a clean, non-abrasive, lint-free

cloth to wipe dust off the screen. DO NOT contact the surface with any pointed or sharp object.

 If you want to put away the mobile computer for a period of time, download the

collected data to a host computer, and then take out the battery pack. Store the mobile computer and battery pack separately.

 When the mobile computer resumes its work, it takes some time for the main and

backup batteries to become fully charged.

 If you shall find the mobile computer malfunctioning, write down the specific scenario

and consult the sales representative in your local area.

 Keep the mobile computer away from any magnets and magnetic fields to prevent the

laser engine from malfunctioning.

DECLARATION OF CONFORMITY

RELEASE NOTES

Version Date Notes

1.01 Aug 22, 2014

1.00 Oct 18, 2013

 Replace Declaration of Conformity  Replace screenshots to match latest OS version  Modify notes for swapping main battery in 1.2.1 Power Menu, 1.4.1

Main Battery Setup, and 1.4.2 Charge Batteries - Replace Main Battery Pack

 Revise 2D scan mode options to Laser, Presentation Mode and Auto

Aim in 2.1.2 General Settings – Scanner Preferences

 Add 5.1 Access Cellular WAN  Add GPRS Manager to 7.2 Control Panel  Add description in 7.3 Connection Settings

 Initial release

CONTENTS

PREFACE ...............................................................................................- 2 -

Disclaimer...........................................................................................- 2 -

Trademark Recognition...........................................................................- 2 -

Contact..............................................................................................- 2 -

For United States..................................................................................- 3 -

Safety Notices......................................................................................- 3 -

Radio wave exposure and Specific Absor ption Rate (SAR) information...............- 3 -

For United States...............................................................................- 4 -

For Product with Laser........................................................................ - 4 -

Safety Precautions.................................................................................- 5 -

Care & Maintenance............................................................................... - 5 -

Declaration of Conformity .......................................................................- 6 -

RELEASE NOTES.......................................................................................- 8 -

INTRODUCTION........................................................................................... 1

About This Document .................................................................................1

Features.................................................................................................2

Inside This Package....................................................................................2

Accessories .............................................................................................2

USE MOBILE COMPUTER................................................................................ 3

1.1. Take a Tour ...........................................................................4

1.1.1. Overview ..............................................................................4

1.1.2. Inside Battery Chamber.............................................................5

1.1.3. Before Initial Use ....................................................................5

1.2. Power on ..............................................................................6

1.2.1. Power Menu...........................................................................6

1.3. Notifications ..........................................................................8

1.4. Battery.................................................................................9

1.4.1. Main Battery Setup ................................................................ 10

1.4.2. Charge Batteries ................................................................... 13

1.4.3. Monitor Battery Level ............................................................. 16

1.4.4. Power Management................................................................ 20

1.5. Keypad............................................................................... 21

1.5.1. Physical keypad .................................................................... 21

1.5.2. On-screen Keyboard ............................................................... 30

1.5.3. Change On-screen Input Method................................................. 35

1.5.4. Edit Text ............................................................................ 36

1.6. Touch Control ...................................................................... 37

1.6.1. Use Touchscreen ................................................................... 37

1.6.2. Screen Orientation................................................................. 37

1.6.3. Adjust Backlight.................................................................... 39

1.6.4. Calibration .......................................................................... 41

1.7. Memory .............................................................................. 42

1.7.1. Data Loss Caution.................................................................. 42

1.7.2. Check Storage ...................................................................... 42

1.7.3. Insert SD Card ...................................................................... 45

1.8. Direct Data Communication...................................................... 46

1.8.1. Use Cable............................................................................ 46

1.8.2. Use Cradle........................................................................... 47

1.8.3. Syncing Tools ....................................................................... 48

1.8.4. Sync Partnership ................................................................... 48

1.8.5. 1st USB Sync ......................................................................... 49

1.8.6. Disconnect USB ActiveSync....................................................... 50

1.8.7. ActiveSync Actions to Take....................................................... 51

1.9. Volume and Audio.................................................................. 56

1.9.1. Audio Playback ..................................................................... 56

1.9.2. Volume Control..................................................................... 56

DATA CAPTURE .........................................................................................59

2.1. Configure Reader .................................................................. 60

2.1.1. Launch Reader Config............................................................. 60

2.1.2. General Settings.................................................................... 61

2.1.3. Symbology........................................................................... 68

2.1.4. Miscellaneous....................................................................... 71

2.1.5. Reader Config Option Menu ...................................................... 72

2.2. Read Printed Barcodes............................................................ 77

CAMERA ..................................................................................................79

3.1. Launch Camera..................................................................... 80

3.1.1. Camera Screen ..................................................................... 80

3.1.2. Camera Toolbar .................................................................... 81

3.2. Take Pictures ....................................................................... 82

3.2.1. Camera Settings.................................................................... 83

3.3. View Pictures ....................................................................... 84

OPERATING SYSTEM....................................................................................85

4.1. Desktop.............................................................................. 86

4.1.1. Taskbar .............................................................................. 87

4.1.2. Start Menu .......................................................................... 88

4.1.3. Customize Desktop and Start Menu ............................................. 89

4.2. Managing Programs ................................................................ 93

4.2.1. Launch Program.................................................................... 93

4.2.2. Switch between Active Tasks .................................................... 94

4.2.3. Exit a Program...................................................................... 94

4.2.4. Install Applications ................................................................ 95

4.3. Suspend & Reset Mobile Computer.............................................. 98

4.3.1. Suspend Mobile Computer ........................................................ 98

4.3.2. Wake Up Mobile Computer ....................................................... 99

4.3.3. Reset Mobile Computer ........................................................... 99

RADIOS.................................................................................................. 101

5.1. Access Cellular WAN..............................................................102

5.1.1. Install SIM Card....................................................................102

5.1.2. Turn On Cellular Data ............................................................103

5.1.3. GPRS Manager .....................................................................106

5.2. Use Wi-Fi ...........................................................................112

5.2.1. Power On Wi-Fi....................................................................112

5.2.2. Launch SCU ........................................................................114

5.2.3. Status Tabbed Page...............................................................115

5.2.4. Configuration Tabbed Page......................................................116

5.2.5. Diagnostics Tabbed Page ........................................................131

5.3. Use Bluetooth......................................................................138

5.3.1. Bluetooth Profiles Supported ...................................................138

5.3.2. Change Blutooth Name...........................................................138

5.3.3. Turn On/Off Bluetooth...........................................................140

5.3.4. Set Bluetooth Visibility...........................................................141

5.3.5. Launch BT Connect ...............................................................142

5.3.6. Search for Bluetooth Devices ...................................................143

5.3.7. Pair Bluetooth Devices ...........................................................144

5.3.8. Bluetooth Data Transfer .........................................................148

5.3.9. Re-Connection.....................................................................158

5.3.10. Preferred Services ................................................................159

5.3.11. Manage Local Services ...........................................................160

5.3.12. BT Manager ........................................................................162

5.4. Use GPS.............................................................................168

5.4.1. Launch GPS.........................................................................168

MORE APPLICATIONS................................................................................. 169

6.1. Button Assignment................................................................170

6.1.1. Launch Button Assignment ......................................................170

6.1.2. Redefine Keys .....................................................................171

6.1.3. Main Menu..........................................................................173

6.1.4. Keypad Modes .....................................................................177

6.2. GPS Viewer.........................................................................181

6.2.1. Launch GPS Viewer ...............................................................181

6.2.2. View NMEA-based Data...........................................................183

6.3. Signature Utility...................................................................184

6.3.1. Launch Signature Utility .........................................................184

6.3.2. Capture Signature.................................................................185

6.3.3. View or Edit Existing Signatures ................................................186

6.3.4. Preferences ........................................................................187

MANAGE MOBILE COMPUTER ....................................................................... 189

7.1. Update OS Image..................................................................190

7.1.1. USB Update ........................................................................190

7.2. Control Panel ......................................................................191

7.3. Connection Settings ..............................................................199

7.4. Taskbar and Start Menu Settings ...............................................202

SPECIFICATIONS....................................................................................... 203

Platform, Processor & Memory...................................................................203

Communications & Data Capture ................................................................203

Electrical Characteristics..........................................................................204

Physical Characteristics ...........................................................................205

Environmental Characteristics....................................................................206

Programming Support..............................................................................206

Accessories ..........................................................................................207

SCAN ENGINE SETTINGS ............................................................................. 209

Symbologies Supported ............................................................................210

LASER (SE955 & SE965HP).......................................................................... 213

Symbology Settings.................................................................................213

Miscellaneous....................................................................................218

AIM Code ID – Code Characters................................................................218

AIM Code ID – Modifier Characters............................................................219

2D IMAGER (SE4500DL).............................................................................. 223

Symbology Settings.................................................................................223

1D Symbologies..................................................................................223

2D Symbologies..................................................................................230

Miscellaneous....................................................................................231

PHYSICAL KEYPAD REFERENCE TABLE ........................................................... 233

Numeric Keypad ....................................................................................233

Using Alpha, Shift & Fn Keys ..................................................................233

QWERTY Keypad ....................................................................................235

Using Alpha, Shift & Fn Keys ..................................................................235

INTRODUCTION

Thank you for choosing CipherLab products. CipherLab welcomes another Windows Embedded by introducing CP60 Series Mobile Computer. Powered by Windows Embedded Compact 6.0, the mobile computer delivers better user experience and advances enterprise mobile computing.

The mobile computer has transflective LCD to hold up the readability in a wide range of light conditions, courtesy of the supplementary backlight enabled by a built-in ambient light sensor. Also on board is a G-sensor to save power according to the mobile computer’s motion and posture. G-sensor also enables screen orientation when the device is posed sideways or upright. Furthermore, the mobile computer has integrated a built-in e-compass and gyroscope, both of which provide useful functions in navigation.

The series sports satisfactory data connections by integrating a communication port for direct data exchange. For wireless data connections it hosts each Bluetooth and 802.11b/g module while a HSPA+ (3.8G) module is provided on option.

Dedicated to data capture, the mobile computer has essential 1D (laser) reader or 2D imager. A high-spec 5 mega-pixel camera also comes inside to take pictures to deliver better documentation for users.

Rated with IP65/67, the rugged CP60 is light-weighted and easy to cradle in your hand, and will be your good help on field works.

ABOUT THIS DOCUMENT

This guide distills the information about CP60 Series Mobile Computer. Subjects discussed include the mobile computer’s physical features, platform basics, software and applications, and part of the accessories to boost the mobile computer’s performance.

We recommend that you keep one copy of this manual at hand for the quick reference for necessary maintenance.

CP60 Mobile Computer (CE) Reference Manual

FEATURES

 Rugged yet smoothened outlined, with hand strap for secure hold  IP65/67-rated tough form to survive drop, shock, heat, cold, and impervious to

moisture/dust

 Windows CE 6.0 OS, TI DM3730 1GHz CPU  512MB SDRAM to run application programs  4GB NAND flash to store OS, applications, settings and so on  Storage expansion: Up to 32GB MicroSDHC  Sunlight-readable screen to enhance the viewability of outdoor use  Ambient light sensor to enable supplementary backlight for LCD and keypad  G-sensor for power management and screen orientation  Gyroscope sensor and E-compass for direction and location sensing  2 symmetric side-triggers for ambidextrous scanning  Total data solution — supporting Bluetooth, 802.11a/b/g/n and HSPA+  Built-in GPS receiver to deliver location discovery information  5 mega-pixel camera for taking pictures  C++ and .Net programming support

INSIDE THIS PACKAGE

The mobile computer ships with the following items. Save the box and packaging material in case of future need to store or deliver the mobile computer.

 Mobile Computer  Rechargeable Li-ion battery pack (standard/high capacity)  Stylus  Screen protector  Hand strap  Product CD  Quick Start Guide

ACCESSORIES

Optional accessories to enhance the mobile computer’s performance are:

 Snap-on Charging and Communication Cable (USB or RS-232)  Charging & Communication Cradle  Pistol Grip  Belt Holster for CP60 with Pistol Grip  Belt Holster with Shoulder Strap for CP60 without Pistol Grip  4-slot Battery Charger  Snap-On Car Charging Kit  Vehicle Mount Cradle  4-slot Terminal Cradle

Chapter 1

USE MOBILE COMPUTER

Before the mobile computer takes part in your work, get to know it first. This chapter includes the basic features of the mobile computer including the power supply, memory, and the units that bridge users with the mobile computer. This chapter helps you set the mobile computer to work at the earliest.

1. IN THIS CHAPTER

1.1 Take a Tour ................................................................ 4

1.2 Power on.................................................................... 6

1.3 Notifications................................................................ 8

1.4 Battery....................................................................... 8

1.5 Keypad..................................................................... 21

1.6 Touch Control............................................................ 37

1.7 Memory.................................................................... 42

1.8 Direct Data Communication......................................... 46

1.9 Volume and Audio...................................................... 56

CP60 Mobile Computer (CE) Reference Manual

1.1. TAKE A TOUR

This section shows the major components on the mobile computer and inside battery chamber. You will also learn how to power on/off the mobile computer and how the mobile computer gives information about its status.

1.1.1. OVERVIEW

Figure 1: Overview

No. Description No. Description

1 Receiver (reserved) 2 Sensors (proximity sensor & light sensor) 3 Status LEDs 4 Touchscreen 5 Scan key 6 Reset button (recessed in keypad) 7 Power button 8 Keypad 9 Microphone (reserved) 10 Charging and communication port 11 Side trigger (user-definable) 12 Application key 13 Scan window 14 Stylus (with attaching cord) 15 Camera 16 Camera flash 17 Speaker 18 Handstrap 19 Battery door 20 Battery door latch 21 Side trigger (user-definable) 22 Volume rocker

Chapte

Use Mobile Compute

1.1.2. INSIDE BATTERY CHAMBER

Inside the battery chamber of the mobile computer are the sockets for SIM card and storage card. Each is equipped with a hinged cover.

Battery chamber

SIM card slot

SD card slot

Figure 2: Inside Battery Chamber

1.1.3. BEFORE INITIAL USE

Prior to using the mobile computer for the first time, we recommend applying the protecti ve film over the LCD. This will prevent scratching the touchscreen during daily usage, and also help enhance the durability of the touchscreen.

To apply the LCD protective film:

1) Upon delivery, the touchscreen of the mobile computer is covered with a thin transparent film. Peel off and discard this film.

2) Wipe the touchscreen with a clean, non-abrasive, lint-free cloth.

3) Carefully apply the LCD protective film to the touchscreen by aligni ng its edges with the

edges of the touchscreen. Make sure the film adheres tightly to the surface.

The mobile computer is then ready for usage.

CP60 Mobile Computer (CE) Reference Manual

Tap

1.2. POWER ON

To power on the mobile computer, press the Power butto n sitting at the upper right of the keypad. The mobile computer powers on.

1.2.1. POWER MENU

The CP60 mobile computer features a power menu. This menu allows you to select whether you would like to power off the mobile computer, enter suspension, or enter sleeping mode for main battery replacement.

To enter this power menu, press the power button for more than three seconds. A menu will open on-screen with a countdown bar at the bottom.

Tap to enter sleeping mode for main battery pack replacement

Menu options are as follows:

Action to take

Swap Battery

Suspend (default)

Description

If you would like to replace the main battery pack on the mobile computer, select this option to let the mobile computer enter sleeping mode.

After the main battery has been replaced, wake up the mobile computer by pressing the power button. All applications and tasks will remain active.

When the mobile computer is not under frequent use, select this option to let the mobile computer enter suspension and save power. This is the default function, and when no option is selected in the power menu, the mobile computer will automatically enter suspension after 5 seconds.

When you need to use the mobile computer once more, resume it by pressing the power button or central scan key. All applications and tasks will remain active.

See also Suspend & Reset Mobile Computer.

to suspend mobile computer

to power off mobile computer

to return to previous screen

Time remaining before mobile computer enters suspension

Power Off

Chapte

Select this option if yo u would like to p ower off the mob ile computer . This will close all applications and tasks currently running. All unsaved data will be lost.

To power on the mobile computer, press the power button.

Use Mobile Compute

Cancel

Selecting this option will close the menu and return to the previously active screen. All applications and tasks will remain active.

Note: If you wish to replace the main battery pack on the mobile computer, aside from

taking the steps above, please also make sure the following requirements are met. Otherwise, the mobile computer might function abnormally, and will require system reset as described in

(1) Make sure the backup battery on the mobile computer is not drained out. Check

Battery Level

before taking any actions.

Reset Mobile Computer.

Backup

(2) After selecting Swap Battery in the power menu, proceed to replacing the battery as

soon as possible.

CP60 Mobile Computer (CE) Reference Manual

1.3. NOTIFICATIONS

The mobile computer features visible, audible, and tactile feedback to draw users’ prompt awareness of the mobile computer’s contiguous events such as barcode reading, wireless/mobile data connections, and battery charging.

STATUS LED

Three LED lights are located on the upper-right corner of the mobile computer. Their functions are:

Matter

Scanning Good Read

(Left)

Radios (Middle)

Battery Charging

(Right)

LED Color Action Description

Indicates good reading of the scanned barcode. Enable/Disable this LED light on the Reader

Green Green, flashes once

Blue Blinking Wi-Fi, Bluetooth or mobile data in use.

Green, solid

Orange, solid

Green, Orange, Red

Red, solid

Red, fast blinking continuously

Config good read LED via API deployment, see the CP60 Programming Guide for details.

Battery is nearly fully charged (battery level>95%).

Battery is charging, and battery level is sufficient for the mobile computer to power on.

Battery is charging, but battery level is too low for the mobile computer to power on.

Charging error that may be caused by temperature dropping below 0°C or exceeding 35°C. See also

Notification Settings page. To set the

Charge Batteries.

SPEAKER

The mobile computer has a speaker on the back for audio signaling and playback. The speaker sounds for system events, application warnings, on-screen item selection and

physical keypad stroke. In noisy environments, the speaker remains efficacious with the help of a Bluetooth headset. To control sound volume, see

Volume Control.

The speaker also sounds for successful barcode reading, which can be controlled on the Reader Config

Notification Settings page. Speaker good read sound is also programmable

through API deployment. For details, see the CP60 Programming Guide.

VIBRATOR

The mobile computer owes its tactile feedback to the vibrator built inside. Vibration delivered to the mobile computer alerts users of its currents status.

Working based on user’s sense, the vibrator is particularly helpful when the mobile computer is serving in a noisy environment.

Same as the speaker and LED light, the vibrator also works for good barcode reading. Enable/disable vibration and set its duration on the Reader Config page. Alternatively, program the vibrator through API deployment to have it vibrate when a successful reading occurs. For details, see the CP60 Programming Guide.

Notification Settings

Chapte

Use Mobile Compute

1.4. BATTERY

The mobile computer is fed by two batteries, main battery pack and backup battery. The main battery is removable and replaceable from the battery chamber while the backup battery is mounted on the main board inside the mobile computer.

When the mobile computer is shipped, the main battery is stored in a package separated from the mobile computer, which keeps it in good condition for future use.

MAIN BATTERY

The main battery is a Li-ion battery pack that comes in two sizes, a standard 3.7V/3600mAh pack and a high capacity 3.7V/4400mAh pack. The standard battery will take aroun d 4 hours to charge to full, while the high capacity battery pack will require approx imately 6 hours charging to reach full battery level. The working time of the mobile computer varies by its working states. See operate under different conditions.

Operating Time for details on how long the mobile computer will

1.4.1. MAIN BATTERY SETUP

To secure main battery in place, the battery door is equipped with two l atches, one on each side. After pressing the battery door in, turn the door latches inwa rds to lock the battery door in place.

Battery door latches

Figure 3: Battery Door Latches

Chapte

To install the main battery pack, follow through the steps below by referencing to the illustrations:

Use Mobile Compute

Figure 4: Main Battery Setup

CP60 Mobile Computer (CE) Reference Manual

1) Loosen the handstrap and pull it downwards so the metal hook is positioned at the lower edge of the Velcro band

2) Unhook the hand strap by pressing the square metal ring lightl y in the middle and lifting it upwards in a single motion.

Note: The lower end of the handstrap can be le ft as is without detaching. After the main battery is installed, the handstrap can be hooked back into place.

3) On the outer sides of the battery door are two door latches. Pull them outwards to unlock battery door.

4) Lift up the lower end of the battery door to remove it.

5) Position the main battery pack into the battery chamber with the contact pins facing

down. Fix the bottom edge first.

6) Press the upper end of the main battery inwards until the clip at the top “clicks” into place.

7) Replace the battery door. Fix the upper edge first and then press the lower edge in. Push the door latches back to their original position.

8) Secure the handstrap hook back into its groove.

Note:

(1) When main battery level drops to low level, charge it ASAP or replace it with a charged one. (2) Always press the power key and select Swap Battery in the Power Menu

before replacing the main battery pack. Otherwise, the mobile computer might function abnormally, and will require system reset as in Reset Mobile Computer

. (3) The battery door must be secured in place for the mobile computer to operate. (4) Any improper handling may reduce battery life.

Chapte

Use Mobile Compute

1.4.2. CHARGE BATTERIES

Due to shipment, it is likely that the main battery and backup battery won’t be fully charged when you receive the package. Before setting the mobile computer to work, charge the main battery to full by direct charging via a power adapter (with the help of a Snap- on Charging & Communication Cable or Charging & Communication Cradle).

Some key facts about charging batteries:

Charging Time

 Main battery: It takes approximately 4 hours to charge the standard size main battery, and 6

hours to charge high capacity battery to full (via direct charging with power adapter). The battery charging LED above the touchscreen (the one to the right) lights red or orange during charging (depending on the battery level at the moment), and lights green when the mobi le computer is nearly 100% charged.

 Backup battery: The backup battery is rechargeable by both main battery and power adapter.

It takes about 5 hours to charge it to full, however it does not need to be fully charged for the mobile computer to work.

Charging Temperature

 It is recommended that batteries be charged at room temperature (18°C~25°C) for optimal

performance.

 Charging stops when temperature drops below 0°C or exceeds 35°C. In this case the battery

charging LED will be continuously blinking in red.

Power Consumption

 When all radios (802.11 a/b/g/n, Bluetooth, mobile data (HSPA+), GPS) are active on battery

power, main battery level drops substantially.

 In order to prevent the system from shutting down due to depletion of the main battery, we

suggest that you keep a fully charged battery for replacement or have the mobile computer access the radios on external power.

The following guides how to charge batteries.

CP60 Mobile Computer (CE) Reference Manual

DIRECT CHARGING USING SNAP-ON CABLE

Direct charging of the mobile computer relies on the Snap-on Charging & Communication Cable (hereinafter “snap-on cable”). There is a power jack on the connector of this cable to connect external power.

Prior to charging, install the main batt ery as described in

Main Battery Setup. Then follow

the steps below:

1) Attach the snap-on cable to the mobile computer.

2) Plug the head of the power adapter cord into the power jack located on snap-on cable’s

connector.

3) Connect the power adapter to a power outlet. To output data to your PC or laptop, connect the snap-on cable (either through USB or

RS-232 connection) to it. See

Direct Data Communication for follow-ups.

When data transmission is required.

Figure 5: Direct Charging Using Snap-on Cable

Chapte

Use Mobile Compute

DIRECT CHARGING USING CRADLE

Direct cradle charging makes use of a Charging & Communication Cradle (hereinafter “cradle”). The cradle is one of the accessories you can opt for.

Prior to charging, install main battery as described in

Main Battery Setup. Then follow the

steps below:

1) Seat the mobile computer into the cradle.

2) Connect the cradle to an external power source using the power adapter.

To output data to your PC or laptop, connect the mobile computer and your PC with a microUSB cable. See

Direct Data Communication for follow-ups.

Only when data transmission is required.

Figure 6: Direct Charging Using Cradle

REPLACE MAIN BATTERY PACK

The Cradle holds a separate charging compartment for the main battery pack. This allows the mobile computer and a separate main battery pack to be charged either individually or simultaneously. We advise you to keep a fully charged battery at hand at all times using the Cradle.

If the main battery level is running low and you decide to replace it with a fully charged one, follow the procedure in

Note: If the process for swapping batteries is not followed, you might need to

Computer for it to function normally.

Power Menu to swap the battery.

Reset Mobile

CP60 Mobile Computer (CE) Reference Manual

1.4.3. MONITOR BATTERY LEVEL

The main battery is the only source that feeds the mobile computer to work. It also supplies the backup battery on main board to retain the data stored in DRAM. Hence when main battery level gets low, recharge it or change it as soon as possible. Most critically, back up the important data from time to time to protect your work.

MAIN BATTERY LEVEL

To check the main battery level:

1) Tap Start | Settings | Control Panel | Power

Power Properties window opens showing Battery tabbed page. Main battery level is summarized under Power label as “Good”, “Low” or “Very Low”. Precise battery l evel is also shown in percentage under the Main batteries label.

Depending on whether the main battery is being charged, charging status will show as “Main battery”, meaning the mobile computer is on battery power, “Charging”, meaning that the main battery is being charged by the adapter, or “External”, meaning that the adapter is connected but the main battery is finished charging.

Power adapter is not connected.

Power is connected and main battery is being charged.

Main battery level descriptions are as follows:

Description

Good

Low

Very Low

Battery Status

Main battery level is good (40~100%). Main battery level is low (20~39%). Charging is recommended. Main battery level is very low (<19%) and needs to be charged

immediately.

Chapte

Use Mobile Compute

BATTERY STATUS ICONS

The OS features a couple of icons that deliver main battery status. These icons can be found on the taskbar, which is settled at the bottom of every screen.

Battery charging icon

Battery level is illustrated by the following icons :

Icon

Battery Status

Main battery level is 91%~100%. Main battery level is 71%~90%. Main battery level is 51%~70%. Main battery level is 21%~50%. Main battery level is 11%~20%. Main battery level is 1%~10%. Charge or replace main battery immediately!

Main battery is being charged from external power.

Mobile computer is connected to external power, but main battery level is full and does not need charging.

CP60 Mobile Computer (CE) Reference Manual

LOW BATTERY ALERT

When main battery level drops below 40%, the mobile computer prompts “Main Battery Low” for a recharge. When further reduced to under 20%, the mobile computer prompts “Main Battery Very low” to solicit your immediate action.

Low battery may incur shutdown to the mobile computer and cause DRAM data damage. Always save data before running short of power or keep a fully charged battery at hand for replacement.

Note: Constant usage of the mobile computer at low battery level can affect battery life. For

maximum performance, recharge the battery periodically to avoid battery drain out and maintain good battery health.

When main battery drains out, the mobile computer shuts down automatically. Backup battery takes over to hold DRAM data for 30 minutes if it is fully charged. When this occurs, replace main battery pack immediately to avoid data loss.

Chapte

Use Mobile Compute

BACKUP BATTERY LEVEL

1) To check backup battery level, tap Start | Settings | Control Panel | Power . On Battery tabbed page of Power Properties window, backup battery level is

summarized as “Good”, “Low” or “Very Low” under the Power label.

Backup battery level descriptions are as follows:

Description Battery Status

Good

Low

Very Low

Backup battery level is good. Backup battery level is low. Charging is recommended. Backup battery level is very low and needs to be charged immediately.

LOW BATTERY ALERT

When backup battery level drops to “Very Low”, the mobile computer prompts a “Backup Battery Very Low” warning to alert users that backup battery level is almost drained out.

Backup battery is rechargeable by the main battery pack or the power adapter. Low backup battery puts DRAM data in great danger. Always save data from time to time or keep a fully charged battery at hand for replacement.

Once backup battery drains out completely, the data in DR AM is gone. Any data that has not been saved will be lost!

CP60 Mobile Computer (CE) Reference Manual

1.4.4. POWER MANAGEMENT

Power issues are critical for portable devices. Always turn off the features you don’t need on the mobile computer in order to save power. To extend battery life as long as possible, always take the following actions:

 Suspend the mobile computer when it isn’t actively in use. See

Computer

 Turn down LCD backlight brightness as described in

LCD timeout as described in

 Auto Sync the mobile computer with your PC less frequently. See

Communication

 If you are using any “push e-mail” or any automatic syncing service on the mobile

computer, change the syncing schedule to manually check updates

 When Wi-Fi, Bluetooth, mobile data (HSPA+), or GPS isn’t used, turn it off. See

Adjust Backlight, and set a shorter

Suspend & Reset Mobile Computer

Suspend Mobile

Direct Data

Radios

Chapte

Use Mobile Compute

1.5. KEYPAD

The mobile computer has a physical keypad and a touchscreen to receive user’s input. Among the two, the touchscreen provides more intuitiveness in interacting with the device.

This section shows how to input text using physical keypad an d on-screen keyboard. To know how to operate the mobile computer using the touchscreen, see

Touch Control.

1.5.1. PHYSICAL KEYPAD

The physical keypad on the front of the mobile computer bears much resemblance to laptop or PC keyboards. It is either a numeric type or a QWERTY one, each wedging a set of “enhanced keys” along the top and a set of character keys at the lower half. Both keypads support multi-key operation, which normally requires two keys hit simult aneously, one of which is a modifier key.

As for entering text, the numeric and QWERTY keypad are equally capable of entering numbers, letters, symbols and punctuations. Both also receive supplementary backlight along with the screen.

Figure 7: Numeric Keypad Figure 8: QWERTY Keypad

ENHANCED KEYS

Enhanced keys are arranged along the top of the physical keypad, separate from the character keys. Use these “enhanced keys” to launch actions on the mobile computer and OS, operate the active application, or switch the physical keypad between input modes. Navigation keys are included also to move the caret in a text input field, and to select between applications on the desktop.

Figure 9: Enhanced Keys

CP60 Mobile Computer (CE) Reference Manual

Enhanced keys can be categorized into five groups and are explicated as follows:

Key Group

ACTION KEYS

OS KEYS

Description

The Scan key is an action key which delivers the function below:

Key Press

Reads barcodes

Scan Key

Turns on/off screen backlight

Backlight Key

The following tabulates OS keys and their functions. Some of them are engraved in orange, which means Function key needs to be pressed beforehand in

order for the keys to function properly.

Key Press

Windows

Opens beforehand.)

 Confirms input in an input field. (Requires Function Key

Start Menu. (Requires Function Key pressed

pressed beforehand.)

 Delivers the same function as the “OK” button on the title

bar of the active window. (Requires beforehand.)

Send Key available for function assignment in CipherLab utility

Button Assignment.

Function Key pressed

NAVIGATION KEYS

FUNCTION KEY

End Key available for function assignment in CipherLab utility

Button Assignment.

 Opens the previous screen worked on.  Closes a menu of an application, or an opened dialog.

Tab

The buttons right below Scan key are the up/down/right/left navigation keys:

They move the caret in an input field. In certain applications, they navigate vertically or horizontally among highlighted items.

Function key applies its action when used in conjunction with other keys. Together they make the OS take actions or produce functions and more.

Function key comes with an LED indicator beside it which behaves as follows:

 Navigates among the highlight items in some applications.  Enters Tab character, which means it moves the caret to

the next tab stop.

through

 When Fn key is pressed once, the LED indicator lights up in orange, and the

function engraved in orange on the keypad is delivered to the next pressed key. The LED goes off once another key is pressed.

 When Fn key is pressed twice, the LED indicator stays lit, and the function

engraved in orange on the keypad is delivered to all pressed keys. This mode will continue until Fn key is pressed again.

In addition to the LED light, the icons

on the Taskbar will display once

Chapte

Function mode is triggered.

Use Mobile Compute

Mode Description

The Fn key is also effective by pressing and holding it and then pressing the desired key.

When other text input modes are activated at the moment, pressing the Fn key will alter the input mode and the icon on the

QWERTY Keypad for details on other text input modes.

Function is delivered to the next pressed key. Function is delivered to all pressed keys.

Taskbar. See Numeric Keypad and

[ALPHA] KEY

[Alpha] key changes keypad input mode. When [Alpha] key is pressed once, [alpha] mode is activated temporarily, and the LED indicator next to the physical key lights up in blue accordingly. This mode will end after a single key has been pressed. Upon pressing any key, keypad input mode will resume back to default, and the LED indicator will turn off.

When [Alpha] key is pressed twice, [alpha] mode is activated permenantly, and the LED indicator next to the physical key stays lit. Press the key again to quit this mode and return to default.

With combined use of the Shift key six input modes to the physical keypad. Mode availability however depends on keypad type, numeric or QWERTY. On a numeric keypad, 6 text input modes are provided, while on a QWERTY keypad, 2 modes are available.

The icons

on the Taskbar signify current input state.

, the [alpha] key delivers a maximum of

 Numeric keypad input modes triggered by [Alpha] key:

Mode Description

Physical keypad enters an alphabetic character indicated in blue for the first key pressed.

Physical keypad enters alphabetic character indicated in blue for all keys pressed.

 QWERTY keypad input modes triggered by [Alpha] key:

Mode

Description

Physical keypad enters a number or symbol indicated in blue for the first key pressed.

Physical keypad enters numbers or symbols indicated in blue for all keys pressed.

CP60 Mobile Computer (CE) Reference Manual

NUMERIC KEYPAD

Numeric keypad wedges a set of character keys at the lower half. They are laid out similar to a telephone keypad, and additionally featured are an

, Backspace key , and Shift key that enable more sophisticated text input.

Numeric keypad enters numbers 0 through 9 by default. Symbols * through ) and

key, Tab key , Enter key

alphabetic characters can be entered by combined use of the [Alpha] key

. See Keypad Modes for more details.

Key Description

 Opens the previous screen worked on.  Closes a menu of an application, or an opened dialog.

Tab

 Navigates among the highlight items in some applications.  Enters Tab character, which means it moves the caret to the next tab stop.

Executes a command or confirms input. For text input, it inserts a break between paragraphs.

and Shift key

Backspace

Space

Shift Shift key changes keypad input mode of keys 0-9. When Shift key is

Erases the characters to the left of caret. Inserts a blank space where caret is. (Alpha key required beforehand.)

pressed once, [Shift] mode is activated temporarily, and the LED indicator next to the physical key lights up in green accordingly. This mode will end after a single key has been pressed. Upon pressing any key, keypad input mode will resume back to default, and the LED indicator will turn off.

When Shift key key is pressed twice, [Shift] mode is activated permenantly, and the LED indicator next to the physical key stays lit. Press the key again to quit this mode and return to default.

Chapte

Use Mobile Compute

KEYPAD MODES

With combined use of the [Alpha] key key and Shift key , enables eight input modes for keys 0-9 on the physical keypad. The icons on Taskbar signify the

current input state.

 Numeric keypad input modes:

Mode Description (Keys 0-9) Trigger and Withdrawal

Default mode.

This mode remains until

Press once to enter this mode.

Input mode returns to default once a key is pressed.

Press twice to enter this mode.

Input mode returns to default by pressing

No icon

Keypad enters numbers only.

Keypad enters the first typed key as a symbol.

Keypad enters all typed keys as symbols.

Mode Description (Keys 2-9) Trigger and Withdrawal

Keypad enters the first typed key as an alphabetic letter.

Press once to enter this mode.

Input mode returns to default once a key is pressed.

or is pressed.

again.

Keypad enters the first typed key as a capitalized alphabetic letter.

Keypad enters all typed keys as alphabetic letters.

Keypad enters all typed keys as alphabetic

Press and once to enter this mode.

Input mode returns to default once a key is pressed.

Press once and twice to enter this mode.

Input mode returns to default once a key is pressed.

Press twice to enter this mode.

Input mode returns to default by pressing

Press

twice and once to enter this mode.

again.

CP60 Mobile Computer (CE) Reference Manual

letters and capitalizes the first one.

Input mode returns to default by pressing

again.

Jumps to mode after a singl e key is pressed.

Keypad enters all typed keys as capitalized alphabetic letters.

Press both and twice to enter this mode.

Input mode returns to default by pressing

again.

Note:

(1) For details about key, see [Alpha] Key. (2) Only keys 2-9 are used for alphabetic input. The remaining keys “0” and “1” are used for

entering symbols and/or spaces only. Refer to the blue writing engraved on the keypad to check the characters these two keys input under various [Alpha] modes.

TEXT INPUT

To enter text by numeric keypad:

 Numeric Input

The numeric keypad enters numbers 0-9 by default when neither Shift key

 Literal Input

is pressed.

key nor

1) To enter a single letter, press

enter the letter in uppercase, press Shift key

key once so appears on the Taskbar. To

additionally to trigger mode.

To enter multiple letters, press key twice so appears on the Taskbar. Additionally, press Shift key letter in uppercase, or press it twice to activate

once to activate mode and enter the first

mode in wh ich all letters are

entered in uppercase.

2) Continuously press a key engraved with blue wr iting until th e character you desire is entered.

 Symbols Input

To enter a single symbol, press Shift key

once so is seen on the Taskbar.

To enter multiple symbols, press Shift key twice to activate mode.

2) Press one or more text input keys until the desired symbol is entered.

Chapte

Use Mobile Compute

QWERTY KEYPAD

QWERTY keypad also arranges its character keys in the lower half and features them in a compact “QWERTY” layout as its name suggests.

QWERTY keypad is a pared down version of an average laptop’s keyboa rd that bears also an

key, Tab key , Enter key , Backspace key , Shift key , and space key

QWERTY keypad enters alphabetic characters by default. To enter numbers and some symbols, press [Alpha]

Key Description

Backspace

Erases the characters to the left of caret. Executes a command or confirms input. For text inp ut, it inserts a bre ak between

paragraphs.

key. See [Alpha] Key for more details.

Space

Inserts a blank space where the caret is.

 Opens the previous screen worked on.  Closes a menu of an application, or an opened dialog.

Tab

Shift Shift key changes keypad input mode. When Shift key is pressed once,

 Navigates among the highlight items in some applications.  Enters Tab character, which means it moves the caret to the next tab stop.

[Shift] mode is activated temporarily, and the LED indicator next to the physical key lights up accordingly. This mode will end after a single key has been pressed. Upon pressing any key, keypad input mode will resume back to default, and the LED indicator will turn off.

When Shift key key is pressed twice, [Shift] mode is activated permenantly, and the LED indicator next to the physical key stays lit. Press the key again to quit this mode and return to default.

CP60 Mobile Computer (CE) Reference Manual

KEYPAD MODES

With combined use of the key, Shift key enables four input mo des for t he phys ical keyp ad. The icons

on Taskbar signify current input state.

 QWERTY keypad input modes:

Mode Description Trigger and Withdrawal

No icon

Keypad enters lowercase letters.

Keypad enters the first typed key as a capitalized letter.

Keypad enters all typed keys as capitalized letters.

Keypad enters the first typed key as a number/symbol.

Keypad enters all typed keys as numbers/symbols.

Default mode.

This mode remains until

Press once to enter this mode.

Input mode returns to default once a key is pressed.

Press twice to enter this mode.

Input mode returns to default by pressing again.

Press once to enter this mode.

Input mode returns to default once a key is pressed.

Press twice to enter this mode.

Input mode returns to default by pressing

or is pressed.

again.

Note:

(1) For details about key, see [Alpha] Key. (2) The follow ing input modes are also available on the QWERTY keypad, however their

functions overlap with those denoted above:

Mode Description

Same input as

Jumps to

Same input as mode.

mode.

mode after a single key is pressed.

TEXT INPUT

To enter text using QWERTY keypad:

 Literal Input

1) The QWERTY keypad enters lowercase letters a-z by default when neither

nor Shift key

is pressed.

Chapte

Use Mobile Compute

key

To enter a letter in uppercase, press Shift key To continuously type in uppercase, press Shift key

2) Press keys to enter text as desired.

 Numeric or symbols Input

1) To enter a single number/symbol, press

Taskbar.

To enter multiple numbers/symbols, press Press a key engraved with blue-color character to enter number(s) and symbol(s)

2) as desired.

so appears on the Taskbar.

twice to trigger mode.

key once so appears on the

key twice to trigger mode.

CP60 Mobile Computer (CE) Reference Manual

1.5.2. ON-SCREEN KEYBOARD

The OS provides users with an on-screen keyboard. Compared to a physical keypad, the on-screen keyboard bears likeness to a laptop keyboard as it has modifiers keys arranged on the left edge and features a “QWERTY” layout. The on-screen keyboard supports entering a series of diacritics for European languages by tapping a modifier key.

The on-screen keyboard auto-opens in some applications while in others it doesn’t unless you tap on a field that accepts input.

In case the on-screen keyboard doesn’t open automatically, tap the keyboard icon

on the taskbar and select Keyboard to open it. On-screen keyboard opens and readies to enter lowercase letters, numbers, and a few frequently used symbols.

On-screen keyboard opens.

Backspace

Input modifier

Caps Lock

Shift key

Ctrl key

Taskbar

Input modifier

Enter ke

Navigation keys

Opens menu to hide on-screen keyboard

Space bar

Chapte

Use Mobile Compute

MODIFIER KEYS

Although the touchscreen is a resistive single-touch type, use of modifier keys, which normally involves hitting two keys, are still available on on-screen keyboard.

On on-screen keyboard there are five modifier keys, which are seated at the left edge. These keys work as follows:

1) Press a modifier key on on-screen keyboard.

The on-screen keyboard enters modifier state.

2) Press the second key.

The desired performance will be produced to the active application or screen at the moment.

CP60 Mobile Computer (CE) Reference Manual

Modifier keys are explicated as follows:

Key

Ctrl key

Shift key

Caps Lock

Input modifier

Description

Once tapped, it becomes color-inverted active application when a character key is tapped. It quits once the said action is triggered or when it is tapped again.

For example: Tap Windows environment usually selects all content on the active screen. Once “A” is tapped, the on-screen keyboard quits Ctrl state.

Once tapped, it becomes color-inverted quits once a character key is tapped or it is tapped again.

To enter all caps, use Caps Lock Once tapped, it becomes color-inverted

characters typed. It doesn’t quit until it is tapped again. This key does not affect numbers, punctuation marks, or symbols.

Once tapped, it becomes color-inverted such as ä, æ, ë, ï, ö, ú or letter variants such as ß and ç which are needed for European languages. It quits once a character key is tapped.

key and then tap key “A” to produce Ctrl+A function, which in

and causes a special action from OS or the

and capitalizes the (one) letter typed. It

and capitalizes all the alphabetic

and presents a series of accented vowel s

Tap

key on on-screen keyboard.

key becomes color-inverted .

Then tap a character key.

Chapte

Letter variant “ü” is entered

Use Mobile Compute

After the letter variant “ü” is entered, the on-screen keyboard restores to normal English alphanumeric layout.

Diacritical letters and letter variants are presented bother lowercase and uppercase.

Lowercase

Uppercase

CP60 Mobile Computer (CE) Reference Manual

OTHER KEYS

Key Description

Tab key

Backspace

Enter key

Navigation keys Move caret in an input field. In certain applications, they navigate vertically or

Navigates among the highlight items in some applications. For text input, it inserts Tab character, which means it moves caret to the next tab stop.

Erases the characters to the left of caret.

Executes a command or confirms input. When text input, it inserts a break between paragraphs.

horizontally among highlight items.

Spacebar

Inserts a blank space where the caret is.

CHANGE KEYBOARD ORIENTATION

The mobile computer is built-in with a G-sensor and su pports screen orient ation, wh ich is enabled by default. So when the mobile computer turns sideways or upright, the screen changes its orientation, and on-screen keyboard also readjusts itself to the new orientation.

Upright (Portrait Mode) Sideways (Landscape Mode)

To disable automatic screen rotation, see Screen Orientation.

Chapte

Use Mobile Compute

1.5.3. CHANGE ON-SCREEN INPUT METHOD

Aside from the on-screen keyboard, the CP60 mobile computer features another on-screen input method called Transcriber, which is a handwriting recognition sof tware that can be used within any application. It supports text input on any part of the screen, and also recognizes entire words instead of individually written letters.

To enable Transcriber as the on-screen input method:

1) Tap the keyboard icon

on the taskbar.

A context menu pops up.

2) Select Transcriber for handwriting recognition. You may start to input text by

handwriting. You may also access Transcriber Options to set

handwriting direction and pen properties, and enable handwriting gestures for other functions. Note these options are accessible only when Transcriber is selected as the active input method on the taskbar.

CP60 Mobile Computer (CE) Reference Manual

1.5.4. EDIT TEXT

On the mobile computer, you may cut, copy, and paste text within an application or across applications by the menu commands. Some applications don’t support editing some or all of the text they display while others may offer their own way to edit text.

EDIT TEXT IN INPUT FIELDS

To edit text in a text input field:

1) Tap where you want to edit text.

Caret moves to the desired place and manifests itself as a vertical bar that blinks to indicate where the typed or pasted text will be inserted.

2) Type, paste or delete text.

To paste text, see

Paste Text.

SELECT TEXT

When you see some text on a page you want to copy, select it first by tapping and dragging the caret so the desired text is highlighted.

CUT OR COPY TEXT

After a text is selected, tap the Edit menu on the title bar of the active window to open an option menu that includes Copy/Cut commands. Tap them to copy/cut the selected text.

PASTE TEXT

Within the OS, texts can be copied to and from certain applications. To paste text:

1) Tap the text field where you want to paste the text.

2) Tap the Edit menu on the title bar of the active wi ndow and select the Paste command.

Chapte

Use Mobile Compute

1.6. TOUCH CONTROL

The mobile computer’s LCD is overlaid by a resistive touch panel and thus forms a resistive touchscreen. Since a resistive touchscreen locates the user’s touch by the force appli ed on it, by operating with the stylus one can apply minimum force to trigger actions from the touchscreen.

Touch control is one of the main ways to interact with the mobile computer. It provides the ability to manipulate icons, buttons, menu commands, the on-screen keyboard, or any on-screen items.

1.6.1. USE TOUCHSCREEN

The mobile computer comes with a stylus. Use it to touch-operate the mobile computer. Apply the gestures below to work on the touchscreen:

 Tap – Touch any item on the screen such as an application icon or a setting icon to work

on it, or touch any key on the on-screen keyboard to type it.

 Tap and hold – Touch an item on the screen and do not release until an action occurs.  Drag – Touch and hold an item for a moment and then, without release, move the item

on-screen until you reach the target.

 Double-tap – Touch quickly twice on certai n screens to zoom. For example, double-tap

a section of a webpage in a web browser to zoom that section so it fits the width of the screen. Some applications such as map-info applications support picture zooming with double-tap.

 Rotate screen – On most screens, the screen rotates as the mobile computer changes

its orientations between upright and sideways.

1.6.2. SCREEN ORIENTATION

The mobile computer has a built-in G-sensor for screen orientation. In order to enable automatic screen orientation:

1) Tap Start | Settings | Control Panel | Screen Rotation

CP60 Mobile Computer (CE) Reference Manual

Screen Rotation window opens with three orientation modes to select from and an option to suspend the mobile computer when the screen is facing down.

Three screen orientation modes

Allows mobile computer to enter suspension when facing down

2) Tap the modes that you wish to enable. The tapped item will light up to indicate it is

currently enabled.

apped items will light up

3) Tap OK on the title bar to apply the changes.

The mobile computer will then automatically switch between the enabled modes according to its physical orientation. For instance, if Portrait and Landscape modes are enabled, the touchscreen will switch between upright and sideways view accordin g to the user’s holding position. However, if only Portrait (upright) mode is enabled, the touchscreen will stay in upright mode regardless of the mobile computer’s orientation.

Chapte

Use Mobile Compute

SIGNATURE MODE

The signature mode is for combined usage with the CipherLab application Signature. With this mode enabled, the screen will immediately rotate 180° when the fr ont of th e mobil e computer is tilted outwards, which is convenient for signing by a second party.

Note: If no modes are selected in Screen Rotation, the mobile computer’s touchscreen

will be fixed in portrait mode.

1.6.3. ADJUST BACKLIGHT

Screen backlight can be adjusted manually or automatically. Upon shippin g, the mobile computer is set to automatic adjustment, which helps saves power. Alternatively you can set the backlight manually according to your preferences.

MANUAL BACKLIGHT ADJUSTMENT

To adjust screen backlight:

1) Tap Start | Settings | Control Panel | Backlight Setting .

Brightness tabbed page opens with a checkbox to enable manual backlight setting, and

slidebars for setting screen and keypad backlight levels By default, Manual backlight setting is unchecked. The light sensor embedded on the

front of the mobile computer will detect current lighting environments, and screen and keypad backlights will adjust automatically according to the backlight profiles set under the Profile tabbed page.

When Manual backlight setting is checked, screen and keypad backlights will stay at the set level and will not adjust automatically.

Brightness tabbed page

Select whether to enable manual backlight setting

Slide to set backlight level as desired

2) Tap Save in the lower right corner to apply the settings.

CP60 Mobile Computer (CE) Reference Manual

AUTOMATIC BACKLIGHT PROFILES

The mobile computer stores three backlight profiles to represent backlight level under different environments. These can be configured according to user’s likings.

To set backlight profiles:

1) Tap Start | Settings | Control Panel | Backlight Setting .

Brightness tabbed page opens.

2) Uncheck Manual backlight setting to enable profile function.

3) Switch to the Profile tabbed page.

Three profiles, Dark, Bright, and Brightest are available in the drop-down box. Select the profile you would like to modify and use the slidebars below to set the backlight levels to your preferences. The screen backlight will change temporari ly to show the effect.

To restore profile settings to default, tap the Default button at the top right corner.

Tap the drop-down box to select between different profiles

4) Tap Save in the lower right corner to apply the settings.

Tap to restore the backlight profile settings to default

Slide to set backlight level as desired

Chapte

Use Mobile Compute

1.6.4. CALIBRATION

A resistive touchscreen needs calibration to work accurately after serving for a period of time. Calibration aligns the coordinates of the touch panel and the LCD underneath to improve touch accuracy.

To calibrate the touchscreen:

1) Tap Start | Settings | Control Panel | Stylus

2) Tap Calilbration tabbed page.

Calibration tabbed page opens. Tap Recalibrate button to open the calibration

screen.

3) Using the stylus, tap firmly at the center of the cross that appears on-screen. Five

crosses will appear in sequence. Follow the on-screen instructions to save the new calibration settings or restore the old

settings. Once completed, the screen returns to Calibration tabbed page.

CP60 Mobile Computer (CE) Reference Manual

1.7. MEMORY

The mobile computer packs the following internal memory units to retain data and instructions from users:

 Internal Storage: Random-access Memory (RAM) and Flash Memory

512MB SDRAM for temporary storage and fast access of active applications. When the main battery pack is absent, SDRAM is fed by backup battery to retain data.

4 GB NAND flash memory is used to store the OS (Windows Embedded Compact 6.0), application files, settings, and user data.

 External Storage

Insert a storage card to increase the mobile computer’s storage capacity. Supported are MicroSDHC cards up to 32GB.

1.7.1. DATA LOSS CAUTION

When main battery is absent or used up, backup battery on the main board takes over to supply power to the mobile computer. A fully charged backup battery retains SDRAM data and suspends the mobile computer for 30 minutes.

Note if you are leaving the mobile computer to sit for a couple of days, data loss will occur when both main and backup batteries drain out. Consider backing up data before putting away the mobile computer.

1.7.2. CHECK STORAGE

INTERNAL STORAGE

To check internal memory size:

1) Tap Start | Settings | Control Panel | System

Information

revealing information about the mobile computer’s assemblage and hardware/firmware components, including device manufacturer, device ID, memory size, and firmware/software version. Both RAM and internal storage size are listed.

Expand to view information on memory size

. System information opens

Chapte

RAM

To check RAM usage on the mobile computer:

Use Mobile Compute

1) Tap Start | Settings | Control Panel | System

2) Tap Memory tabbed page.

This page delivers capacity and usage of the SDRAM onboard. Memory is divided into Storage memory and Program memory.

 Storage memory: RAM used for file storage, such as the OS, applications, files and data.  Program memory: RAM used for running applications.

RAM used for OS file storage

Memory tabbed page

RAM used for running applications

USER DATA

“User data” is a partition which stores data in the non-volatile flash memory of the mobile computer. Data or programs stored in this directory will not be erased even after hardware reset. To check the remaining storage capacity for user data, tap Start | Settings | Control Panel | Storage

Information

label.

, and check the USER_DATA

CP60 Mobile Computer (CE) Reference Manual

EXTERNAL STORAGE

For external storage, tap Start | Settings | Control P anel | Storage Information . The available space on the storage card is shown under the Storage Card label. (If no storage card is installed on the mobile computer, the available space will be shown as 0.)

CP60 Mobile Computer (CE) Reference Manual

1.7.3. INSERT SD CARD

Day-to-day use of the mobile computer might cause the available internal storage to run short. Equip the mobile computer with an external memory uni t to expand storage capacity.

Follow the steps below to install a SD card:

1) Power off the mobile computer.

2) Place the mobile computer face-down on a flat and soft surface.

3) Remove the battery door and main battery pack as described in

Battery chamber is opened.

4) Using a screwdriver, remove the battery chamber back cover.

5) Locate the SD card socket inside battery chamber. (See

Inside Battery Chamber.) The

SD card socket is equipped with a hinged cover.

6) Push the hinged cover to the open position.

7) Swivel up the cover.

8) Insert SD card into the cover slot in

Main Battery Setup.

Figure 10: Inserting SD Card

the direction indicated metal contact pins should face down

9) Put down the hinged cover and lock it into place.

10) Restore the battery chamber back cover, main battery pack and the battery door.

. The

CP60 Mobile Compute

(CE) Reference Manual

1.8. DIRECT DATA COMMUNICATION

“Direct” data connection means “hardwired” data connection between the mobile computer and a Windows-based PC as opposed to wireless connection. Direct data connection relies on a RS-232 cable or a USB cable (sometimes plus an auxiliary cradle) between the two mentioned devices. Once the mobile computer and PC are “directly” connected with each other by a RS-232 or USB-cable, they can sync data with each other.

1.8.1. USE CABLE

Direct data communication using a cable:

1) Connect the mobile computer to your PC with a Snap-on Charging and Communication Cable (either USB or RS-232 type) .

2) On the mobile computer, tap Start | Settings | Control Panel | USB Connection

3) To connect the mobile computer and PC via ActiveSync, select ActiveSync Advance Network Mode or ActiveSync Serial Mode.

To treat the mobile computer as an external storage device, select Mass Storage – SD Card.

4) Tap OK on the title bar to apply the settings. If one of the first two options are selected, ActiveSync will automatically detect

connection between the two and prompt for data synchronization. See

Syncing Tools and subsequent sections to know how to use ActiveSync.

Figure 11: Direct Data Comminucation Using Cable

Chapte

Use Mobile Compute

1.8.2. USE CRADLE

Direct data communication using a cradle:

1) Seat the mobile computer in a Charging and Communication Cradle (hereinafter “cradle”).

2) Connect the cradle to your PC with a USB cable. Fix the cable to both sides. ActiveSync will automatically detect connection between the two and prompt for data

synchronization. See

Syncing Tools and subsequent sections to know how to use ActiveSync.

Note: The cradle supports USB Host Mode via a USB OTG cable.

Figure 12: Direct Data Communication Using Cradle

CP60 Mobile Compute

(CE) Reference Manual

1.8.3. SYNCING TOOLS

Microsoft’s syncing tools enables users to update or back up the data on their mobile computers to desktop computers.

Two syncing tools are featured by Microsoft - ActiveSync and Windows M obile Device Center (“WMDC”). Which tool to use depends on which OS is running on your PC. See the rule below:

Windows Vista or Windows 7

Windows XP SP3 and earlier

ActiveSync and WMDC can be downloaded from Microsoft’s website. Download and install the right one on your PC.

Hereafter in this manual, we will focus on ActiveSync only. For WMDC usage, see its documentation or help file.

Syncing Program

WMDC

ActiveSync

1.8.4. SYNC PARTNERSHIP

Once a direct connection is established between the mobile computer and your PC as described in

Sync Partnership

Synchronization Relationship

Use Cable or Use Cradle, they are able to form the following ties:

Services

 Allows the mobile computer and PC to sync data with each other.  Allows PC to add and remove programs to/from the mobile

computer.

 Allows PC to browse files on the mobile computer.  Alllows PC to copy files to/from the mobile computer.  Allows PC to back up the files on the mobile computer.

Temporary Relationship (Mobile computer works as a “guest” to PC)

 Allows PC to add and remove programs to/from the mobile

computer.

 Allows PC to browse files on the mobile computer.  Allows PC to copy files to/from the mobile computer.  Allows PC to back up the files on the mobile computer.

Note that data stored on external storage (the SD card) cannot be synchronized. See

ActiveSync Actions to Take for details about the mentioned services.

Chapte

Use Mobile Compute

1.8.5. 1ST USB SYNC

This section will guide you through USB syncing. For Bluetooth syncing, see Bluetooth

ActiveSync

To connect ActiveSync using USB:

1) Download the right syncing tool as described in

2) Connect the mobile computer and your PC as described in

3) On your PC, run the syncing program.

ActiveSync should detect the mobile computer. Sync Setup Wizard launches and prompts to set up

4) Press Next for “Synchronization Relationship”, or press Cancel for “Temporary Relationship” if you don't plan to connect to the PC on a regular basis.

If you have pressed Next, follow the on-screen instructions and select the data categories you would like to synchronize. Once confirmed, synchr onization will begin shortly, and when the process is finished, ActiveSync wind ow will show “Synchroni zed” to indicate that the data on the mobile computer and PC are identical.

Sync Partnership between two computers.

Syncing Tools and install it on your PC.

Use Cable or Use Cradle.

A “Synchronization Relationship” is established between the mobile computer and the PC

CP60 Mobile Compute

(CE) Reference Manual

If you have pressed Cancel, Microsoft ActiveSync opens showing “Guest” and “Connected”. The mobile computer and the PC are connected but the data is not synchronized.

A “Temporary Relationship” is established between the mobile computer and the PC

Note: If you encounter trouble during USB ActiveSync connection, tap Start | Settings |

PC Connection and make sure “Enable direct connections to the desktop computer” is selected. Tap Change Connections and check that USB Serial is selected as the connection method.

1.8.6. DISCONNECT USB ACTIVESYNC

To disconnect USB ActiveSync:

1) On your PC, open ActiveSync by double-clicking its icon ActiveSync opens.

2) From the menu bar, click File | Connection Settings. [Connection Settings] window opens.

3) Deselect Allow USB connections.

4) Press the OK button to apply the change and quit setting.

This way when you plug your mobile comput er the next time, ActiveSync won’ t attempt to connect to it.

in the notification area.

Chapte

Use Mobile Compute

1.8.7. ACTIVESYNC ACTIONS TO TAKE

Once “Synchronization Relationship” or “Temporary Relation ship” is established between two computers, a variety of actions can be taken to enhance resource sharing between them as previously mentioned in

In summary, “Synchronization Relationship” outshines “T emporary Relat ionship” by bein g capable of syncing Microsoft Office Outlook data. However “Temporary Relationship” provides satisfactory file sharing if you don’t want to synchronize information.

See the following to know what actions to take with ActiveSync:

ADD/REMOVE PROGRAMS

Note basically the applications to be installed to the mobile computer need to be installed on your PC first. So download the application programs to your PC first and install them on your PC so they can be installed onto the mobile computer later.

Many application programs are installed in different ways. Read their installation guides or documentation to know how they are installed. If you are installing an application that cannot be installed on your PC first, try to install it right from the mobile computer. See

Install Applications for more details.

Sync Partnership.

To install an application on the mobile computer:

1) Connect two computers as described in

2) Sync two computers as described in

Use Cable or Use Cradle.

1st USB Sync.

3) On the PC, from the menu bar of Ac tiveSync, select Tools | Add/Rem ove Programs.

ActiveSync starts to search for the application programs installed on your PC and opens its [Add/Remove Programs] dialog which lists those found. Each entry comes with a check box on the left. An unchecked box means the program is yet to install to the mobile computer while a checked one means an installed program.

CP60 Mobile Compute

(CE) Reference Manual

4) Select the application program(s) to install to the mobile computer, and deselect the application program(s) to uninstall from the mobile computer.

5) Press the OK button. ActiveSync proceeds to install programs and/or remove programs to/from the mobile

computer.

6) Follow the on-screen instructions on both your PC and the mobile computer to proceed.

Noteworthy facts:

 Normally the application program(s) downloaded from external resources are installed

to the mobile computer’s directory at My Device\Program Files. However sometimes there are exceptions and the actual situation depends on the application.

 You can also uninstall applications directly on the mobile computer rather than on the PC.

Uninstall Applications for more details.

See

 If you would like to uninstall a program that isn’t listed in the [Add/Remove Programs]

dialog, browse to it on the mobile computer by tapping My Device desktop. Tap and hold it, and select Delete from the context menu that pops up.

on the

ADD APPLICATION SHORTCUTS TO START MENU

ActiveSync features “Explore” to add an application shortcut to Start menu where it is easier to launch the application.

To add an application shortcut to Start menu:

1) Connect two computers as described in

2) Sync two computers as described in

Use Cable or Use Cradle.

1st USB Sync.

3) On the PC, from ActiveSync’s menu bar, select Tools | Explore Device, or from its toolbar, press Explore

button.

Chapte

Use Mobile Compute

The mobile computer’s internal storage root directory “Mobile Device” opens presenting a few folders (and files).

4) Add File Shortcuts to Desktop Double-click My Windows Mobile-Based Device .

5) Double-click Program Files.

Program Files folder opens. This is where the downloaded applications are normally installed on the mobile computer’s local storage.

In the folder, each sub-folder stores an application.

6) Open the folder of the application to create shortcut for.

7) Find the executable file of that application. Right-click on it and select Copy from the

context menu that comes up.

8) Browse to My Device\Windows\Programs.

9) Right-click any vacant spot in the folder and select Paste shortcut from the context

menu that comes up. A shortcut to the application is added to the mobile computer’s Start menu.

Note: You can also copy & paste by the sequence Create Shortcut -> Cut -> Paste. You can also add an application shortcut to Start menu directly on the mobile computer. See

Add Items to Start Menu for more details.

CP60 Mobile Compute

(CE) Reference Manual

ADD ITEM SHORTCUTS TO DESKTOP

To add a shortcut of an application or file to the mobile computer’s desktop:

1) Connect two computers as described in

2) Sync two computers as described in

Use Cable or Use Cradle.

1st USB Sync

3) On the PC, from ActiveSync menu bar, select Tools | Explore Pocket PC, or from its toolbar, press Explore

button.

The mobile computer’s internal storage root directory “My Device” opens presenting a few folders.

4) Browse to the file to create shortcut for.

5) Right-click on the file and select Copy from the context menu that comes up.

6) Browse to My Device\Windows\Desktop.

7) Right-click any vacant spot in the folder and select Paste shortcut from the pop-up

menu that comes up. A shortcut to the file is added to the mobile computer’s desktop.

Note: You can also copy & paste by the sequence Create Shortcut -> Cut -> Paste.

You can also add a file shortcut to the desktop directly on the mobile computer. See Add

Items to Start Menu

or more details.

REMOVE ITEMS FROM START MENU

To remove an added shortcut from Start menu, simply use ActiveSync’s Explore to delete the shortcut from My Device\Windows\Programs folder.

You can also remove an added shortcut from Start menu directly on the mobile computer.

Add Items to Start Menu for more details.

See

CREATE NEW FOLDERS

To create a new folder on the mobile computer:

1) Connect two computers as described in

2) Sync two computers as described in

On the PC, from ActiveSync menu bar, select Tools | Explore Device, or from its toolbar, press Explore

button.

The mobile computer’s internal storage root directory “My Device” opens presenting a few folders (and some files).

3) Browse where you want to create a folder.

4) Right-click any vacant spot there.

Context menu opens

5) Select New Folder. A new folder is created.

Use Cable or Use Cradle.

1st USB Sync.

Chapte

Use Mobile Compute

BACKUP DATA

To best protect your work, back up the data on your mobile computer regularly. You may choose to manually back up using ActiveSync to copy & paste the files to your PC.

USB PASS-THROUGH NETWORKING

ActiveSync supports “Pass-Through Networking” whereby the mobile computer networks using your PC’s data connection.

For security, disable network bridging on the PC, especially the bridging to a Remote NDIS adapter. For more information on network bridging, see Windows Help on the PC.

After sync partnership is set up between the mobile computer and your PC:

1) On your PC, from the menu bar of ActiveSync, select File | Connection Settings. [Connection Settings] window opens.

2) For This computer is connected to, select a network which your PC should connect to when passing through ActiveSync. Options are:

Option

Automatic Auto-detects proxy.

Description

 This option detects if a proxy should be used when passing connections

through the PC. If yes, configure the proxy on the mobile computer.

 This option best suits connecting to a PC (laptop) that may be used at

home (with no proxy), as well as to a corporate network (with proxy).

Work Network Always uses proxy.

 This option assumes a proxy should be used when passing connections

through the PC, and uses whatever proxy is already configured on the mobile computer.

 This option best suits connecting to a PC that is always on corporate

network.

The Internet Never uses proxy.

 This option assumes no proxy is necessary when passing connections

through the PC.

 This option best suits connecting to a PC connected directly to the

Internet through ISP (at home)

3) Select Open ActiveSync when my device connects.

4) Press OK button to apply the change and quit settings.

CP60 Mobile Compute

(CE) Reference Manual

1.9. VOLUME AND AUDIO

1.9.1. AUDIO PLAYBACK

Use a Bluetooth headset for audio playback and hands-free telephone c ommunication. See

Use Bluetooth.

Note: Bluetooth headsets that communicate via A2DP are not supported.

1.9.2. VOLUME CONTROL

The mobile computer has two volume control facilities – the physical volume rocker perched on the left side of the mobile computer and the on-screen vo lume gauge featured by the OS.

Both the physical rocker and the on-screen gauge can be used to control the system volume, including event sounds, notifications and media playback.

PHYSICAL VOLUME ROCKER

Use the physical volume rocker to turn up and down system volume.

Volume changes made with the physical volume rocker will also be reflected on the

On-screen Volume Gauge.

Turns up and down system volume

Figure 13: Physical Volume Rocker

ON-SCREEN VOLUME GAUGE

The on-screen volume gauge can also be used to adjust system volume:

1) Tap Start | Settings | Control Panel | Volume & Sounds.

Volume & Sounds Properties window opens showing a slider to adjust system volume and a few checkboxes to select the occasions to play system sounds for.

Slider bar and buttons to adjust system volume

Checkboxes to select when to play system sounds

Chapte

2) Adjust the settings to meet your needs. When finished, tap OK on the taskbar to apply the settings.

Note: When using the physical volume rocker to adjust system volume, make sure Volume

& Sounds window is not the active window on-screen.

Use Mobile Compute

CP60 Mobile Compute

(CE) Reference Manual

Chapter 2

DATA CAPTURE

Although highly converged, the mobile computer is also a dedicated barcode reader. The mobile computer is shipped with either a (laser) 1D reader or 2D imager. A number of symbologies are supported and data about them can be decoded and collected.

After data has been collected, the mobile computer can output it locally to applications installed on the mobile computer or to the host computer so data storage, advanced data analysis and more special services can be performed.

This chapter describes how to collect data with reader modules. Note: The mobile computer allows three forms of data capturing, either by laser scanning,

2D imaging or capturing colored images via the digital camera. Laser scanning and imaging are described in this chapter. For digital camera usage, see

Camera.

2. IN THIS CHAPTER

2.1 Configure Reader....................................................... 60

2.2 Read Printed Barcodes................................................ 77

CP60 Mobile Computer (CE) Reference Manual

2.1. CONFIGURE READER

The mobile computer is capable of reading printed barcodes. The reader module can be a either a (laser) 1D reader or a 2D imager. The mobile computer is installed with a CipherLab utility Reader Config to configure the scan engine built inside. Use it to create a profile of settings that best suits your needs.

2.1.1. LAUNCH READER CONFIG

To launch Reader Config:

1) Tap Start | Settings | Control Panel | Reader Configuration

Reader Config launches in context with the reader module(s) on board the mobile computer. On the main settings page are three sections: General Settings, Symbology and Miscellaneous.

Click to open option menu

Opens scan test page for reading barcodes

Click to exit the application

Reader Config opens showing a main menu with three sections

Click to open Start menu

The following will guide to settings provided in each of the three sections.

Chapter 2 Data Capture

2.1.2. GENERAL SETTINGS

General Settings is where all reader settings are accessed from except for symbologies settings. Tap the green arrow next to each item to enter the sub-menu for that gi ven item.

General Settings

The functions under General Settings include:

 Scanner Preferences  Data Output  Enable Reader - enabled by default  Notification Settings

Tap to enter each sub-menu

CP60 Mobile Compute

(CE) Reference Manual

SCANNER PREFERENCES

Scanner Preferences page can be entered by tapping the given item on the Reader Config main settings page. The options provided in this page differ a ccording to the type of

scan engine (either 1D or 2D) built within the mobile computer. To open Scanner Preferences page:

1) Open Reader Config as described in

Launch Reader Config.

Reader Config settings page opens.

2) Tap the arrow next to Scanner Preferences. Scanner Preferences settings page opens.

Featured settings are different for 1D (laser) reader and 2D imager:

1D (laser) reader settings 2D imager settings

Chapter 2 Data Capture

1D (LASER) READER SETTINGS

Setting Description Default

Decode Timeout Sets the maximum time for the decoding process during a

scan. Configurable between 1 sec to 9 sec.

3 sec

Redundancy Level Sets how many successful readings should be done before

linear barcodes such as Codabar, MSI, and Interleaved 2 of 5 can be decoded. Levels 1 to 4 available.

The readings needed for each level are as follows:

Level Description

Level 1 The following barcodes must be

successfully read twice before being decoded: Codabar, MSI, Industrial 25 (Discrete 25), Interleaved 25.

Level 2 All barcodes must be successfully read

twice before being decoded.

Level 3 All barcodes must be successfully read

twice before being decoded, except for the following which must be read three times: MSI, Industrial 25 (Discrete 25), Interleaved 25.

Level 4 All barcodes must be successfully read

Scan Angle Sets the scan angle for laser scan engine. Options to

choose between are Wide Angle and Narrow Angle.

Scan Mode Sets the reader’s scanning behavior. Options available are

Continuous and Laser modes.

three times before being decoded.

Level 1

Wide Angle

Laser

Timeout Between Symbols Sets the time for the barcode reader to resurrect its ability

to once more decode a barcode it just decoded.

 Only applied in Continuous mode

1 sec

CP60 Mobile Compute

(CE) Reference Manual

2D IMAGER SETTINGS

Setting Description Default

Decode Timeout Sets the maximum time for the decoding process during a

scan. Configurable between 1 sec to 9 sec.

3 sec.

Redundancy Level Sets how many successful readings should be done before

linear barcodes such as Codabar, MSI, and Interleaved 2 of 5 can be decoded. Levels 1 to 4 available.

Security Level Sets the security level to ensure decoding accuracy

considering the printed quality of barcodes such as Code 128, Code 93, and UPC/EAN. The higher the level is, the more security is ensured. Options are:

Level Description

0 With this default, the scan engine is aggressive

enough to decode most “in-spec” barcodes.

1 Select this level if misdecodes have occurred.

It fixes most misdecodes.

2 Select this level if Level 1 should fail to

eliminate misdecodes.

3 Select this level if Security Level 2 should fail

to prevent misdecodes. However, as this level actually impairs the decoding ability of the decoder, a safer solution would be to improve

Inter-Char Gap Size Sets the intercharacter gap size for Code 39 and Codabar.

Switch between Normal and Large.

the quality of the bar codes to read.

Level 1

Level 0

Normal

Scan Mode Sets the reader’s scanning behavior. Options available are

Laser, Presentation Mode and Auto Aim.

Laser

 Laser: Decoding process is activated by trigger event

and continues until trigger event ends, a valid decode happens or decode session time-out is reached.

 Presentation Mode: The imager engine attempts to

decode when an object appears in its field of view. Sleeping state is not entered when this mode is activated.

 Auto Aim: Red aiming pattern is turned on when the

imager engine detects motion. A trigger event will then activate decoding. If 2 seconds go by without any activity, the aiming pattern goes off.

Decoding Illumination Enables an LED light beam to aid barcode reading. Selected

(Enabled)

Decode Aiming Pattern Projects a crosshair at the center of the laser light beam to

facilitate barcode reading.

Picklist Mode When selected, only barcodes aligned at the crosshair of

the laser light beam will be decoded.

Selected (Enabled)

Deselected (Disabled)

Chapter 2 Data Capture

DATA OUTPUT

Data Output allows users to set the way to output decoded data. To open Data Output settings page:

1) Open Reader Config as described in Reader Config main menu opens.

2) Tap the arrow next to Data Output. Data Output settings page opens.

Launch Reader Config.

[Data Output] settings

WHERE TO OUTPUT

Keyboard Emulation setting controls where the decoded data is to be output.

Setting

Keyboard Emulation Treats decoded data as typed text and outputs it to the active

Descriptions Default

application locally on the mobile computer or remotely on a computer. Options are:

 Disable – Disables Keyboard emulation whereby decoded

data won’t be output.

 Input on local machine – Passes decoded data locally to the

active application on the mobile computer. Simply run an application such as Wordpad to collect decoded data.

 Input on remote PC – Passes decoded data to the active

application on the remote computer connected. Set up a remote PC connection to collect data. (Note this option is unable to pass double-byte characters such as Big-5 or Unicode characters.)

Input on local machine

CP60 Mobile Compute

(CE) Reference Manual

HOW TO OUTPUT

After the output destination is set, configure how to output decoded data, i.e. the “format” to present decoded data.

Setting

Auto Enter Adds an ENTER character before or after each scanning act.

Description Default

Decoded This function saves the trouble pressing [Enter] key to confirm each scan. Options are:

data +

Enter

 Disable  Decoded data + Enter  Enter + Decoded data

Auto Enter character Adds a key code before or after the decoded data. This

setting is available only when [Auto Enter] is enabled. Options are:

Carriage

Return

 None  Carriage Return  Tab  Space  Comma  Semicolon

Display Code Type Prefixes the output data with code type information. Deselected

(Disabled)

Show Code Length Suffixes the output data with code length information. Deselected

(Disabled)

Prefix Affi xes 0 to 10 characters to the left of the output data. Tap

the keyboard icon character table for entering the prefix.

next to the input field to open a

 Prefixes containing invisible characters are supported.

Suffix Affixes 0 to 10 characters to the right of the output data. Tap

the keyboard icon character table for entering the suffix.

next to the input field to open a

 Suffixes containing invisible characters are supported.

Field Delimiter Sets the delimiter to separate the output barcode data to the

following pieces: code type, decoded barcode data, and code length (if applicable). Options are:

Comma

 Comma  Semicolon  Full stop

ENABLE READER

Features a checkbox to enable or disable reader scanning ability. When enabled, light beam will be sent out each time the trigger (scan key) is pressed.

Chapter 2 Data Capture

NOTIFICATION SETTINGS

Notification Settings enables audible, visible and tactile feedback for scanning go od read, which helps notify the user of a successful decoding.

To open Notification Settings page:

1) Open Reader Config as described in

Launch Reader Config.

Reader Config main menu opens.

2) Tap the arrow next to Notification Settings. Notification Settings page opens.

[Notification Settings]

Setting

LED

Vibrator

Beeper Select a sound

Enable LED when good read

Vibrator

Vibration duration Sets the duration for tactile feedback (vibration). --

Description Default

Selects to enable/disable LED light (left) for scanning good read. See

Enables/disables tactile feedback (vibration) for good read.

Sets the beeper sound for scanning good read. Users can choose to mute the beeper sound, or configure the beeper between sounds 1 to 9.

Status LED for details.

Deselected (Disabled)

Sound 1

CP60 Mobile Compute

(CE) Reference Manual

2.1.3. SYMBOLOGY

Symbology section sets the symbologies to read, and also enables/disables some feature(s) for a symbology to read, such as:

 Customize and transmit start/stop characters  Verify/transmit check digits  Enable/disable addon digits  Convert to another symbology  Transmit symbology ID

Symbology

To open Symbology settings page:

1) Open Reader Config as described in Reader Config main menu opens.

2) Tap the arrow next to 1D Symbologies (or 2D Symbologies in the case of a 2D imager).

Launch Reader Config.

Chapter 2 Data Capture

Symbology settings page opens listing all symbologies which can be decoded.

1D Symbologies 2D Symbologies

SYMBOLOGY SETTINGS

Tap the arrow next to each symbology checkbox to access detailed settings for that symbology.

CP60 Mobile Compute

(CE) Reference Manual

GENERAL PREFERENCES

For certain symbologies, common settings are grouped together and displayed in a detailed settings page for that barcode family. To open the general settings page for a set of symbologies, tap the arrow next to General Preference.

General settings are provided for Composite Code, Postal Code, and UPC/EAN families.

For details about the featured settings:

 See Appendix II: 1D Laser  See Appendix III: 2D Imager

Symbology Settings.

Chapter 2 Data Capture

2.1.4. MISCELLANEOUS

This section allows enabling code ID transmission fo r easy identification of the scanned barcode, and enabling picklist mode to enhance decoding accuracy.

Miscellaneous

Setting

Transmit AIM Code ID Sets whether to include AIM code ID character in the

Description Default

decoded data. For AIM code ID, see the following:

 Appendix II: 1D Laser Symbology Settings  Appendix III: 2D Imager Symbology Settings

Deselected (Disabled)

CP60 Mobile Compute

(CE) Reference Manual

2.1.5. READER CONFIG OPTION MENU

Reader Config provides an option menu which is accessible on the menu bar of the main settings page. This menu allows you to import/export all settings in a re-usable format , reset all settings back to factory default, view copyright and version information, and exit the application.

Chapter 2 Data Capture

RESET TO FACTORY DEFAULTS

This function restores all settings in the Reader Config application to default. To enable Factory Reset:

1) Open Reader Config as described in Reader Config main menu opens.

2) Tap Menu button on the menu bar to open the option menu.

3) Tap Reset to Factory defaults.

4) A warning dialog appears confirming whether to restore all application settings back to

default. Tap Yes to reset or No to close the dialog.

Launch Reader Config.

A warning dialog pops up to confirm if reset should be performed

CP60 Mobile Compute

(CE) Reference Manual

IMPORT AND EXPORT

Reader Config supports saving the settings and exporting them as an .xml file. Previously exported symbology and scanner settings can be imported again on the mobile

computer. This can also be used to implement identical Reader Config settings on two or more devices.

To import settings:

1) Open Reader Config as described in Reader Config main menu opens.

2) Tap Menu button on the menu bar to open the option menu.

3) Tap Import in the option menu.

A page opens allowing you to select a previously saved profile.

Launch Reader Config.

Select a previously exported profile

4) Select the profile you would like to apply and tap OK. In a few seconds a prompt will appear on the mobile computer to indicate settings have been imported successfully.

Chapter 2 Data Capture

To export settings:

1) Open Reader Config as described in Reader Config main menu opens.

2) Tap Menu button on the menu bar to open the option menu.

3) Tap Export.

An export page opens allowing you to enter and select information about the prof ile to be saved.

Launch Reader Config.

Enter a name for the profile to save

4) Enter file name, storage folder and location. Tap OK to export. A prompt will appear on-screen to notify that settings have been exported.

CP60 Mobile Compute

(CE) Reference Manual

ABOUT

Tap About in the Reader Config option menu to display software version and copyright information.

Information about the software

Chapter 2 Data Capture

2.2. READ PRINTED BARCODES

Aside from output to destinations as per Keyboard Emulation settings, Reader Config provides a Scan Test feature for quick viewing of decoded data.

To perform test scanning of barcodes:

1) Open Reader Config as described in

2) Tap Scan Test on the menu bar.

A Test Scan Form opens for displaying the scanned data.

3) Aim the scanning window at the printed barcode to read and press the scan key (or any of the two side triggers).

Launch Reader Config.

The scanning light beams to read the printed barcodes. The scanning light goes off once data is decoded, or decoding timeout is reached.

Figure 14: Read printed barcodes

CP60 Mobile Compute

(CE) Reference Manual

The decoded data will appear on the page. When finished viewing, tap on the title bar to leave the test scan page.

Tap to exit the test scan page

To display more information such as barcode type and length, configure the reader as in

Data Output.

You may also configure the reader module(s) as described in

Configure Reader before

starting to collect data.

TEST SCAN MENU

Tap the Menu button to save the decoded data as a .txt file, clear all data shown on the screen, or exit the Test Scan page.

Tap to save the decoded data as a .txt file

Tap to clear all the data onscreen

Tap to exit Test Scan

Chapter 3

CAMERA

The mobile computer is equipped with a 5.0 mega-pixel camera. The OS also has an integrated camera application for taking pictures and storing them on the mobile computer’s storage where they can be viewed, edited and output.

The camera application provides users with customization that allows better image documentation.

This chapter will guide you to use the camera. Note: When the camera is active, the 2D imager will be temporarily out of service. To

re-launch the reader module, close the camera application.

3. IN THIS CHAPTER

3.1 Launch Camera ......................................................... 80

3.2 Take Pictures ............................................................ 82

3.3 View Pictures ............................................................ 84

CP60 Mobile Computer (CE) Reference Manual

3.1. LAUNCH CAMERA

To launch the camera:

1) Tap Start | Programs | Camera Capture

Camera application opens and is ready to take pictures.

3.1.1. CAMERA SCREEN

Camera opens showing a subject area on the screen, and a toolbar at the top.

Toolbar

Exits camera application

Camera screen

Chapter 3 Camera

3.1.2. CAMERA TOOLBAR

The camera toolbar allows users to take and save pictures, view saved images, adjust camera settings, enable camera flash light and view information of the application.

Button

Description

Views pictures saved on the mobile computer’s internal storage. Supported file formats include .bmp and .jpg files.

Saves the picture taken (or the image opened) to the mobile computer’s internal storage.

Triggers camera shutter button to take a picture.

Opens

Enables/disables camera flash light.

Camera Settings.

 Flash light default settings can be adjusted in Camera

Settings

Opens a dialog that delivers application version information.

CP60 Mobile Computer (CE) Reference Manual

3.2. TAKE PICTURES

To take a picture:

1) Open camera as described in

Launch Camera.

2) Enable/disable camera flash and adjust picture quality or other settings according to your preferences. See

Camera Settings.

3) Frame your object on the screen.

4) Press the Enter button on the keypad to take the picture.

After the picture is taken, a preview of it will appear brief ly on the screen.

 To save the taken picture, tap the settings button

on the toolbar. By default, pictures taken will be stored under My Device\Windows\CameraCapture\Image in .jpg format. To change the default storage path, see

 To discard the taken picture, tap the exit button

Camera Settings.

at the top right corner of the

preview screen.

ap to close the application ap to close the preview screen

Preview of picture taken

Chapter 3 Camera

3.2.1. CAMERA SETTINGS

The camera supports changing resolution, flash light mode, camera effect, brightness, and default file storage format and location.

To access camera settings:

1) Open camera as described in

2) Tap the

button in the toolbar.

Launch Camera.

A dialog appears on-screen showing various option settings.

Available settings are detailed as below:

Item

Resolution The mobile computer supports the following resolutions: 240x320, 480x640,

Flash light Sets the default flash light setting as Off, On or Auto. Flash light can also be

Feature Sets camera effect between Mono, Sepia, Negative, or Off. Image Format Sets the format of the saved picture as .jpg or .bmp. EV Sets exposure value between 1 and 5 in increments of 1. Default image store Changes the default path to store the pictures taken.

Description

960x1280, 1200x1600, 1536x2048, 1944x2592.

controlled using the

Camera Toolbar.

CP60 Mobile Computer (CE) Reference Manual

3.3. VIEW PICTURES

To view a taken picture or an image stored on the mobile computer:

1) Tap the

2) Browse to the desired path and select the file to view.

The picture will be displayed in the preview screen below.

3) When finished viewing, tap the exit button screen.

button on the toolbar.

at the top right corner of the preview

Chapter 4

OPERATING SYSTEM

The mobile computer is powered by Windows Embedded Compact 6.0, a member of Windows Embedded family. Windows Embedded Compact 6.0 bears much similarity to desktop OS, and users rely only on a few basic gestures such as tap, double-tap and drag to navigate within the OS.

4. IN THIS CHAPTER

4.1 Desktop ................................................................... 86

4.2 Managing Programs ................................................... 93

4.3 Suspend & Reset Mobile Computer............................... 98

Chapter 4 Operating System

4.1. DESKTOP

Desktop is where all features on the mobile computer are accessed from. Basic operations on the desktop:

 Tap the Start button

to open the Start menu.

 Double-tap an application icon to open it.  Customize the desktop by changing the background and the items to display. See

Customize Desktop and Start Menu for more details.

Take a look around the desktop:

Application icon

Taskbar

Items on the desktop include:

Icon

Description

File explorer for the mobile computer’s internal storage.

Recycle bin.

Shortcut for Internet Explorer.

Shortcut for Windows Media Player.

Shortcut for Microsoft WordPad.

Shortcut which opens \My Device\My Documents directory.

Shortcut for Remote Desktop Connection.

Shortcut which enables Transcriber as the active input mode.

Chapter 4 Operating System

4.1.1. TASKBAR

At the bottom of the screen is the taskbar, which is divided into the following sections:

 Start button: opens Start menu  Task button section that shows a minimized window button of t he current application or

task open on-screen

 Notification area which displays icons for connection status of the mobile computer, as

well as system time

 A keyboard icon for switching input mode  A task icon to switch between active applications or re-open the desktop

Displays icons for connection status

Switches input mode

Opens Start menu

Task button section

Shows system time

Switches task

STATUS ICONS

The OS presents the following icons for users. Note there may be application-specific icons not included here.

Icon

Description

External power source connected and charging.

External power source connected, but battery level is full.

Battery icons indicate the amount of power remaining in the main battery. The higher the green level, the more power in the main battery.

When the battery icon changes to red, main battery level is low a nd needs charging immediately.

Numeric keypad enters symbols; QWERTY keypad enters uppercase letters.

 These input mode icons display only when Shift key is pressed.

Numeric keypad enters alphabetic letters; QWERTY keypad enters numbers/symbols.

 These input mode icons display only when Alpha key is pressed.

Keypad Function mode is on.

 These input mode icons display only when Function key is pressed.

PC connection icon that appears when ActiveSync connection is established.

A specific wireless connection is terminated or has failed. Double-tap the icon to open a window to check IP information. Included connections are:

 Bluetooth PAN  802.11a/b/g/n  WWAN

CP60 Mobile Computer (CE) Reference Manual

 Ethernet

A specific wireless connection has been established successfully. Double-tap the icon to open a dialog to check IP information. Included connections

are:

 Bluetooth PAN  802.11a/b/g/n  WWAN connection  Ethernet

Indicates the Wi-Fi mod ul e is e nab led . T h e more the green bars, the stronger the signal. Yellow or red bars indicate poor signal, and a cross indicates no connection is made.

Indicates the status of cellular data connection. See Cellular Data Status Icons for details on the status of cellular data connection.

4.1.2. START MENU

Tap the Start button on the taskbar to open the Start Menu.

Start menu

Options

Programs Accesses programs stored in the directory My Device\Windows\Programs. Favorites Accesses favorite links to webpages that are stored under the directory

Documents Accesses recently opened documents stored under the directory

Settings

Description

My Device\Windows\Favorites.

My Device\Windows\Recent.

Provides access to the following:

 Control Panel  Network and Dial-up Connections  Taskbar and Start Menu

Run Opens a program, folder or document as specified.

CipherLab CP60G, CP60, CP60GCE Reference Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

PREFACE

COPYRIGHT

DISCLAIMER

TRADEMARK RECOGNITION

CONTACT

FOR UNITED STATES

SAFETY NOTICES

RADIO WAVE EXPOSURE AND SPECIFIC ABSOR PTION R ATE (SAR) INFORMATION

FOR UNITED STATES

FOR PRODUCT WITH LASER

SAFETY PRECAUTIONS

CARE & MAINTENANCE

DECLARATION OF CONFORMITY

RELEASE NOTES

INTRODUCTION

ABOUT THIS DOCUMENT

FEATURES

INSIDE THIS PACKAGE

ACCESSORIES

USE MOBILE COMPUTER

1.1. TAKE A TOUR

1.1.1. OVERVIEW

1.1.2. INSIDE BATTERY CHAMBER

1.1.3. BEFORE INITIAL USE

1.2. POWER ON

1.2.1. POWER MENU

1.3. NOTIFICATIONS

1.4. BATTERY

1.4.1. MAIN BATTERY SETUP

1.4.2. CHARGE BATTERIES

1.4.3. MONITOR BATTERY LEVEL

1.4.4. POWER MANAGEMENT

1.5. KEYPAD

1.5.1. PHYSICAL KEYPAD

1.5.2. ON-SCREEN KEYBOARD

1.5.3. CHANGE ON-SCREEN INPUT METHOD

1.5.4. EDIT TEXT

1.6. TOUCH CONTROL

1.6.1. USE TOUCHSCREEN

1.6.2. SCREEN ORIENTATION

1.6.3. ADJUST BACKLIGHT

1.6.4. CALIBRATION

1.7. MEMORY

1.7.1. DATA LOSS CAUTION

1.7.2. CHECK STORAGE

1.7.3. INSERT SD CARD

1.8. DIRECT DATA COMMUNICATION

1.8.1. USE CABLE

1.8.2. USE CRADLE

1.8.3. SYNCING TOOLS

1.8.4. SYNC PARTNERSHIP

1.8.5. 1ST USB SYNC

1.8.6. DISCONNECT USB ACTIVESYNC

1.8.7. ACTIVESYNC ACTIONS TO TAKE

1.9. VOLUME AND AUDIO

1.9.1. AUDIO PLAYBACK

1.9.2. VOLUME CONTROL

DATA CAPTURE

2.1. CONFIGURE READER

2.1.1. LAUNCH READER CONFIG

2.1.2. GENERAL SETTINGS

2.1.3. SYMBOLOGY

2.1.4. MISCELLANEOUS

2.1.5. READER CONFIG OPTION MENU

2.2. READ PRINTED BARCODES

CAMERA

3.1. LAUNCH CAMERA

3.1.1. CAMERA SCREEN

3.1.2. CAMERA TOOLBAR

3.2. TAKE PICTURES

3.2.1. CAMERA SETTINGS

3.3. VIEW PICTURES

OPERATING SYSTEM

4.1. DESKTOP

4.1.1. TASKBAR

4.1.2. START MENU