Cineversum CM 100 Installation Manual
CM 100
R9827341
R9827342
Ceiling support
R9827341
Ceiling support with pulley
How to mount the Ceiling Support to the ceiling is for both products the same.
For the support without pulley, skip the paragraphs handling about the pulley on the next pages.
Ceiling support without pulley
R9827342
231231
CAUTION
THIS SUPPORT IS DESIGNED FOR USE ONLY WITH
THE BARCO 800 AND 1000 SERIES PROJECTORS.
USE WITH OTHER APPLIANCES MAY RESULT IN IN-
STABILITY CAUSING POSSIBLE INJURY
SEE ALSO PAGE 2
Art no : R5975693 rev-06
Date: 03/06/98 Page 1Installation guidelines
CM 100
R9827341
R9827342
CAUTION
INSTALLING THE SUPPORT MOUNT SHOULD BE
PERFORMED ONLY AFTER YOU ARE THOROUGHLY
FAMILIAR WITH ALL OF THE FOLLOWING SAFETY
CHECKS AND INSTALLATION GUIDELINES.
TO DO OTHERWISE INCREASES THE RISK OF HAZ-
ARDS AND INJURY TO THE USER.
WARNING
THE CEILING SHOULD BE CAPABLE OF SUPPORT-
ING A WEIGHT OF AT LEAST 800Kg (1765 LBs).
IF IT CANNOT, THE CEILING MUST BE REINFORCED.
IMPROPER INSTALLATION MAY RESULT IN SERIOUS
PERSONAL INJURY.
WARNING
THIS SUPPORT IS PROVIDED WITH FOUR SECURITY
CHAINS.
NOT INSTALLING THE SECURITY CHAINS MAY RE-
SULT IN SERIOUS PERSONAL INJURY.
Date: 03/06/98 Page 2Installation guidelines
CM 100
R9827341
R9827342
Lowered ceiling
Cord support
Upper support
Screwed rods
Lower support
Projector
Date: 03/06/98 Page 3Installation guidelines
CM 100
CONTENTS INSTALLATION GUIDELILNES
R9827341
R9827342
1. Mounting instructions for the upper
support to the ceiling.(Fig. 1)
a. Position of the upper support on the
ceiling.
b. Mounting of the 4 screwed rods on the
upper support.
) LJ
) LJ
) LJ
2. Projector placement on lower support.
(Fig. 3)
a. Projector placement on support.
b. Location of controls for projector-position
correction.
3. Mounting instructions of the cord to lift up
the projector.
a. Mounting the cord support on the upper
support.(Fig 2)
b. Cord insertion between the upper and lower
support.(Fig.4-5)
c. Cord fixation (Fig. 4)
4. Lifting up and fixing the lower support (with
projector) on the screwed rods.
5. Alignment of the projector-support assem-
bly
a. Projector water-level adjustment.
b. Adjustment "projector axis perpendicular" on
the screen surface.
c. Projector movement for- or backward.
) LJ
) LJ
) LJ
Date: 03/06/98 Page 4Installation guidelines
CM 100
R9827341
R9827342
INSTRUCTIONS FOR CEILING MOUNTING SUPPORT
CAUTION: THIS SUPPORT IS DESIGNED FOR USE ONLY WITH THE BARCO 801, 808,
1000, 1100, 1200, 1208, 1209, 1500, 1600, 5000, 5100, 8000 and 8100 SERIES
PROJECTORS. USE WITH OTHER APPLIANCES MAY RESULT IN INSTABILITY
CAUSING POSSIBLE INJURY.
INSTALLATION GUIDELINES:Refer to illustrations for detail.
PRECAUTION: installing the ceiling mount requires the presence of minimum two
persons, familiar with mechanical installations. A third assistent is recommended.
1. Mounting instructions for the upper support to the ceiling.
WARNING
THE CEILING SHOULD BE CAPABLE OF SUPPORTING A WEIGHT OF AT LEAST
800Kg (1765 LBs). IF IT CANNOT, THE CEILING MUST BE REINFORCED.
IMPROPER INSTALLATION MAY RESULT IN SERIOUS PERSONAL INJURY.
a. Fixation of the upper support to the ceiling.
Refer to the installation manual of the projector to know the throwing distance (PD) of the projector to the screen.
(distance Screen-front support projector).
Mounting-distance upper support from the screen (see fig. 5)
Attention: (refer to fig. 3-4) Keep in mind that the mentioned distance corresponds with a projector mounting with
the screwed rods in the fixation holes 2. This fixation allows to move the projector 5cm for- or backward without
changing the upport support mounting, see point 5c.
The mounting-distance PD' from the screen to the front of the UPPER SUPPORT is equal to the value, found
inthe mounting table of the installation manual of the projector (value PD), minus 11 cm.
PD' = PD - 11cm.
Date: 03/06/98 Page 5Installation guidelines
CM 100
R9827341
R9827342
Fixation of upper support to the ceiling
Fixation procedure in case of a flat solid ceiling
The metallic bridge, welded in the centre of the upport support, could be helpfull in the following way:
- Attach the upper support, front of the support at the correct distance from the screen, to the ceiling with
a bolt of diameter 10mm through the hole in the metallic bridge.
- Move the support into correct position, perpendicular to the screen.
- Mark the 10 fixation holes on the ceiling.
- Remove the upper support and drill 10 holes in the ceiling in order to be able to insert bolts which garantee
a pull downward of at least 800Kg (1765 LBs).
- Attach the upper support to the ceiling with 10 bolts.
Test the fixation to the ceiling for safety and rigidity under moderate side
loads (swaying) and test to at least 800 Kg (1765 LBs) pull downward for
safety.
b. Mounting of the 4 screwed rods. (refer to fig. 2-6)
Screw one nut on each screwed rod. Screw the four rods fully in the welded nuts on the upper support and
secure each rod by fastening nut 1 (see : fig6).
Determination of the lenght of the screwed rods
The lenght of the screwed rods is to be determined as follows (refer to fig. 6):
- the height of the lowered ceiling, if there is one.
- the position of the top side of the screen with regard to the ceiling.
For the latter, consult the installation manual of the projector. In the manual you can read the correction
value A. With this value A is it possible to calculate CD (distance between the ceiling and the top side op the
support, fixed on the projector).
CD = A + B with A = correction value (see installation manual)
with B = distance between the top of the screen and the ceiling.
Explanation of fig 6:
- Case 1: Lowered ceiling 2 in fig. 6 considered as main ceiling
Lenght of the screwed rods: [CD-H4]
- Case 2: there is a lowered ceiling 2.
Lenght of the screwed rods: [CD+H1-H4]
Saw the screwed rods to the necessary lenght and screw on each rod a nut 2.
Date: 03/06/98 Page 6Installation guidelines
Loading...