CIG WF180 Users Manual

WF-180 Wireless Access Point

Thank you for buying this product. The following information aims to give you general
information about product introduction, product overview and installation procedure and
so on.

1. Introduction

WF-180 is a dual-band 2x2streams and chains indoor Wi-Fi AP, which is complied with the
IEEE802.11n standard and designed for high-density deployments in offices, schools,
hospitals and hotels that require premium performance.
Having together MIMO (Multiple-in&Multiple-out) technology with high-throughput mode
techniques, WF-180 works with most wireless terminals to builds a high capacity Wi-Fi
network.

2. Package List

• AP x1

• Wall bracket x1

• Ceiling bracket x 1

• Screw x1

• Cable tie x1

3. Product Overview

No.

Name

Function

LEDs

See LED Definition

LAN Port

10/100/1000M Base-T Ethernet ports (RJ-45), used as a
WAN port and used for being powered by PoE function.

带格式的: 缩进: 左侧: 0 厘米

带格式表格

Console port

Also names as RJ-11, used to manage WF-180 software.

Reset button

Pressing the button longer than 5s to restore the device to
factory defaults and reset the device.

DC power connector

used for connecting the power adapter

USB port

supports a USB 2.0 connector(Support up to 0.5A)

Kensington Lock Slot

What is the function?For additional security

4. Installation

Before you start, To reduce the risk of bodily injury, electrical shock, fire, and equipment
Damage, read all warnings and precautions in this guide before
Installing or maintaining product.read all caution and safety statement in this document.

Caution

To avoid risk of injury from electrical shock or energy hazard, installation and service

of this product must be performed by qualified service personnel.

Make sure the AP fits securely on the ceiling tile rail when hanging the device from

inthe ceiling, because poor installation could cause it to fall onto the peoplefall and make
body injury and equipment damage.

Safety Statement

• To avoid the abnormal work, do not install the device near the power line,
electric lamp, power grid, or in any forceful power grid place

• Ensure the power adapter is grounded well if install the device indoor.

• Install other lightning protection equipment near the device if necessary,

because the lightning protection module inside the device is basic.

• Use the steady power grid to provide the power to the device, which is to avoid
the abnormal work.

• Use a less than 50m network cable to connect the PoE port, which is to acquire
the steady power. The network cable complies with the DC resistance
definition in the YD/926.2 protocol.

Installation Environment

• Operating ambient temperature: 0℃ ~ 45℃

• Operating ambient humidity: 5% ~ 95% non-condensing

Installation mode:

• Wall mounting and ceCelilingmounting.

带格式的: 字体: 非加粗, 字体颜
色: 自动设置

带格式的: 字体: (中文) 宋体, 非
加粗, 字体颜色: 自动设置

带格式的: 字体: 小四, 字体颜色:
浅蓝

带格式的: 段落间距段前: 0.5 行,
段后: 0.5 行

带格式的: 段落间距段前: 0.5 行,
段后: 0.5 行

Installation tool:

• Screws and screw-driver

Installation site:

Please ensure the visibility of product and no tall buildings and woods block
between them.

Installation procedure

Wall mounting

1. Drive two screws fist in the wall. The distantbetween two screws mounted on
the wall is 40mm.

2. Align bracket with the screw, and then pull down the bracket with up to down

direction until it has been fixed tightly.

带格式的: 段落间距段前: 0.5 行,
段后: 0.5 行

带格式的: 段落间距段前: 0.5 行,
段后: 0.5 行

带格式的: 段落间距段前: 0.5 行,
段后: 0.5 行

带格式的: 字体: (默认) Arial,
(中文) 宋体, 小四

3. Align the securing slothookof AP with bracket, and push AP from up to down until
it has been lockedsecured fully.

Ceiling mounting:

1. Fasten ceiling rails by pushing bracket as the indicated direction

带格式的: 段落间距段前: 0.5 行,
段后: 0.5 行

带格式的: 字体: (默认) +西文正
文, (中文) +中文正文, 五号