CicloSport CicloNAVIC 50 Instruction Manual

Table of contents

1. General informations .............................................................................................. 3

2. Operational setup ................................................................................................... 3

2.1 Charging........................................................................................................ 3

2.2 Installing the handlebar bracket..................................................................... 3

2.3 Attaching to the handlebar bracket................................................................ 4

2.4 Attaching to the wristband (optional) ............................................................. 4

2.5 Using the protective cover............................................................................. 4

3. Using the buttons.................................................................................................... 5

3.1 Overview ....................................................................................................... 5

3.2 Button functions............................................................................................. 5

4. Usage..................................................................................................................... 6

4.1 Main mode..................................................................................................... 6

4.2 Bike info mode 1............................................................................................ 7

4.3 Bike info mode 2............................................................................................ 8

4.4 Menu mode ................................................................................................... 8

4.5 Data logging function (recording)................................................................... 9

4.6 Mark a POI (Point of Interest)........................................................................ 9

4.7 Navigation ................................................................................................... 10

4.8 Compass ..................................................................................................... 11

4.9 Backlight...................................................................................................... 11

5. Setting mode ........................................................................................................ 11

GPS INFO......................................................................................................... 11

ODOMETER...................................................................................................... 11

SETTING........................................................................................................... 12

CLEAR DATA.................................................................................................... 12

POWER MODE................................................................................................. 12

TIME ZONE....................................................................................................... 12

CALIBRATION .................................................................................................. 13

UNIT.................................................................................................................. 13

TRACK.............................................................................................................. 13

LANGUAGE ...................................................................................................... 14

6. Connect with PC / PC evaluation.......................................................................... 15

6.1 Installation ................................................................................................... 15

6.2 Using CicloGuide......................................................................................... 16

7. Service and maintenance..................................................................................... 19

8. Trouble shooting................................................................................................... 20

9. Guarantee............................................................................................................. 21

10. Technical Data.................................................................................................... 22

11. Guarantee certificate .......................................................................................... 23

Note: In order to use all functions of the CicloNAVIC 50 in the correct way, please read through this operating manual carefully.

Congratulations !

By purchasing the CicloNAVIC 50 you have acquired high-level GPS-datalogger with

electronic compass and navigation function.

1. General informations

The CicloNAVIC 50 is equipped with a GPS receiver and is so able to calculate and record distance and speed. With the program CicloGuide the recorded tours can be displayed on the PC.

Additionally the CicloNAVIC 50 offers the possibility to reconstruct a tour (with a maximum of 50 waypoints) which was created on the PC. The directional sign in the display is shown by arrows.

For this the the reception of GPS-satellite signals is required. During the first use it can last a bit, to receive the first GPS-signals. The reception of the GPS-signal is shown by vertical bars beside the battery symbol in the upper part of the display.

Attention: whoever carries out sport should have a general medical check up on his/her general state of health – especially beginners, persons older than 35 years of age and anyone who has suffered from illnesses or injuries in the past. It is recommended that a doctor be consulted in any case in the presence of risk factors, such as smoking, high blood pressure, high cholesterol values, diabetes, lack of exercise and excess weight.

2. Operational setup

2.1 Charging

To charge the CicloNAVIC 50 remove the rubber plug on the backside of the CicloNAVIC

50. Connect the mini-USB-plug of the USB-cable with the CicloNAVIC 50 and the USB-plug

with a USB-port on your PC. Charging time is about 2,5 hours.

During the charging a corresponding symbol is shown in upper left display. After the charging remove mini-USB-plug and close rubber plug.

2.2 Installing the handlebar bracket

The handlebar bracket can be mounted on the handlebar (pict. A-1) or on the stem (Abb. A-2).

For using it on the stem rotate the upper part of the bracket. Open the 4 screws, rotate it 90° to the left and assemble it again with the 4 screws (pict. B).

Remove the protective tape from the underside of the handlebar bracket, place the handlebar bracket in the required position on the handlebar (or on the stem) and press it down slightly. Secure it with the cable ties

2.3 Attaching to the handlebar bracket

To insert the CicloNAVIC 50 into the handlebar bracket, rotate it 45° to the left, insert it and then turn it to the right until it engages

To unlock, rotate the CicloNAVIC 50 45° to the left and remove it.

2.4 Attaching to the wristband (optional)

To use the CicloNAVIC 50 also e.g. during hiking an additionally wristband is available (at your dealer). The wristband can be fixed on the wrist, but also on the upper arm. To insert the CicloNAVIC 50 into the wristband operate as described in chap. 2.3.

2.5 Using the protective cover

This package also contents a silicon protective cover for the CicloNAVIC 50. This is useful to protect the CicloNAVIC 50 e.g. of heavy rain during a ride.

Insert the CicloNAVIC 50 into the cover, so that the big opening is on the display and the small opening is on the back.

After use during wet weather the protective cover should be taken off for better drying.

3. Using the buttons

3.1 Overview

3.2 Button functions

Button

LR-Taste

LL-Taste

UL-Taste

UR-Taste

Option

Press 3 sec. Press short

Press short

Press 3 sec.

Press short Press 3 sec.

Press short

Function

• Power on / off the CicloNavic 50

• Backlight on / off

• Switch to next mode or display When in submenu: back to previous mode / display

• Call up POI-menu

• Confirm / set function or setting

• Call up recording menu

• Scroll to requested function or setting

• Show data of previous tour (in Bike info mode)

4. Usage

The CicloNAVIC 50 has four different displays (modes). By short pressing LL-button you can switch from one mode (display) to the next mode (display).

These modes are:

• Main mode

• Bike info mode 1

• Bike info mode 2

• Menu mode

There are additionally three different sport modes (Walk mode, Bike mode, User mode), to optimize specific settings (e.g. memory interval for waypoints, turn radius and so on) of the CicloNAVIC 50 depending on the chosen kind of sport). These sport modes can be chosen in the settings of the menu mode. A symbol in the upper right display of the main mode shows which sport mode is currently chosen.

Note: in order to calculate distance and speed, a recording has to be started before you start the tour (see chap. 4.5)

4.1 Main mode

Main mode (Main display) appears directly after switching on the CicloNAVIC 50 (to switch on press LR-button 3 sec.).

This display shows functions like e.g. current speed and distance, compass and – if started – the navigation by showing arrows in the compass ring.

You can choose by yourself which two functions shall be shown in the middle lines of the display. For this shortly press UL-button in main mode, now upper display line starts blinking. By always shortly pressing UR-button you can scroll between the possible functions, by short pressing UL-button the function is confirmed and stored and now the lower line starts blinking. Here you can choose and store the function in the same way.

Functions:

• Current speed Shows current speed in kilometer per hour (kph) or miles per hour (mph).

• Ride time Shows current riding time.

• Distance Shows current distance.

• Remaining distance Shows the still remaining distance to target point (during a navigation)

• Remaining ride time Shows the estimated remaining ride time to target point (during a navigation)

• Average speed

• Maximum speed

• Current altitude

Shows the current altitude (meter/m or feet/ft).

• Variance altitude Shows the variance (difference) of the current altitude to the altitude at start time (meter/m or feet/ft).

4.2 Bike info mode 1

This mode appears after main mode (with short pressing LL-button). It shows specific tour data (depending on the speed) of the current or last recorded tour. Note: a recording has to be started in order to calculate these values. For this press UL-button 3 sec., display shows small popup with symbols. Press again UL-

button and recording is started (the recording symbol is then shown in the bottom line on the right in the display), see also chap. 4.5.

By short pressing UR-button it shows also the data of the two tours before this one. The counter in the bottom line shows which one of the last three tours is displayed at the moment.

4.3 Bike info mode 2

Appears after bike info mode 1 and shows more details of the tour. Like in bike info mode 1 it can show data of the last three tours.

4.4 Menu mode

Appears after bike info mode 2. Here you can see the POIs, BackTracks (recorded tours), the via PC uploaded tour and theme navigations and also you can do all necessary settings (see chap. 5).

Choose the requested function (with UR-button) and confirm with UL-button.

Options:

POI

Shows all stored POIs (see chap. 4.6).

BACK TRACK

Here you can choose one of the already stored (recorded) tours for ‚BackTrack’ navigation. This means you can go back the tour from end to start point. And you can also choose if you like to go back ‘direct’ (beeline from end to start point) or in ‘sequence’ (same way back as before).

+ 17 hidden pages