CIAudio D-200 Brochure
32
SPL!
MAGAZINE
Home
Entertainment
In the recent years Class D amplifiers are getting in
creasingly popular with car audio amplifiers especially in the
kilowatt class, something Class AB amplifiers never could
achieve and Class A amplifiers is decidedly unfashionable
(see the attached feature on Amplifier Classes Hierarchy)
save for a stubborn few. Class D home amplifiers are
starting to appear – Linn, TacT, Bel Canto EVO, NuForce
and now CI Audio. With Class D efficiency means you can
achieve good power delivery without having to up sizing
power supplies. Transistors are cheap but power supplies
(transformers and capacitors) cost as much as 50%~70%
the asking price of a typical AB amplifier. So it pays to
either maximize efficiency or allows a greater degree of
miniaturization.
The D-200 comes in a compact monobloc package,
the all-aluminum casing is well built and finished. There isn’t
an on/off switch – the front panel button merely mutes the
amplifier. The power supply feed through the power deter
mines if the amplifier is turned on. A rear switch would be
nice. Either way, it points to the D-200’s best left on 24/7.
The innards of the amplifier is sheer simplicity. The
amplification module is attached to the rear panel and
that’s where the heat gets dumped. The large toroidal
transformer and the two large 10,000uF caps dominate.
The review sample comes with balanced input and a pair
of single ended RCA to balance XLR adapter (Cardas, no
less) is provided. You can order the amplifier with just
single ended input. Rated at 200 watts per channel into 8
ohms and a 325 watts into 4 ohms, the D-200 should have
no problems with typical loudspeaker loads save for a few
cases. The amps weigh only about 7 kg each, on first look
it certainly doesn’t belong to the heavy weight class. In this
case, looks can be deceiving.
In my notebook, I read – typical Class D amplifier
– sound – low noise, quiet, clean sounding low frequen
cies, clean sounding high frequencies, analytical midrange,
perhaps dry and lacking emotion.
Boy, was I right and wrong on most counts. I am cer
tainly impressed with the clean sound, almost clinical but
in a very nice sort of way. I would not describe the D-200
was tube-like, tubes are far too muddy sounding most of
the time unless we are talking about some really expensive
tube amps. I am also most impressed with its no nonsense
rendition of the human voice, male voices in particular can
be an entrancing experience. The midrange may be analyti
cal but it is no way a dry and emotionless presentation.
The whole soundstage is airy with a wide spatial spread of
instruments without the sound bunching up into a mess
when it goes loud.
Bass end seems deep enough and well defined in
pitch. Some might like a riper, fuller sounding bass than
the D-200 but I believe the lack of low frequency distortion
makes for a more accurate balance. Perhaps this may take
a bit getting used to. Some would call the bass ‘fast’ mean
ing impressive leading edges with a less than impressive
decay. That is not quite what the D-200 is all about, the
Class D rocks!
Class D amplifiers are by technical reasons;
almost perfect in the way it goes about doing its
business. Think about all those amplifiers you have
used in the past, imagine how much power
goes
to waste, quite unthinkable when today’s oil prices peaks
at over USD60 a barrel and we are burning fossil fuel just
to listen to music! With technology, we should be able to
come up with the purrrrfect amplifier – one with
near 100%
efficiency, unconditionally stable into all loads, immeasurable levels of
distortion, great sound and so on. Well, we are getting there with Class
D amplifiers.
Monoblocs
CI Audio
D-200
33
SPL!
MAGAZINE
Class A amplifiers output stages operate at a constant current equal to
or greater than the current which the load requires. This means that the
output devices (Bipolar, Tubes, Mosfets, IGBTs) are never driven into cut
off. They conduct through 360 degrees of the output waveform. All analog
amplifiers have input and driver stages which pretty much all operate in
pure class A mode. They can because their heat dissipation is relatively low.
What are the disadvantages to pure class A amplifiers. Heat! A reasonable
powered amplifier dissipates enormous amounts of heat. Please refer to
the discussion on Amplifier Efficiency to see some simple calculations of
how efficient a class A amplifier is. For this discussion let’s use an average
figure of say 15% which is a conservative number. This means that for
every 100 watts of power into our amplifier, 85 watts go out as heat and
15 watts go to the loudspeakers! Not a very good situation if you must pay
the electric bill.
Class B amplifiers are the opposite of Class A. They only conduct
through 180 degrees of the output wave form and are all push-pull by
design. The output stage has device(s) for both halves of the waveform.
This means that when the positive device is conducting and sourcing current to the load, the opposite device is cut off (not conducting). This is kind
of analogous to two people on opposite ends of a rope. One pulls and the
other can relax and visa versa. During the time at which one person ceases
to pull and the other starts to pull, the rope is limp (in a cut off stage). This
is the region in which one half of the output stage stops conducting and
there is a short period of time before the other half begins conducting. This
time interval is what we call “crossover distortion”. It manifests itself as a
small time step on the sinewave on both the positive and negative going
halves of the sinewave.
In order to reduce this crossover distortion to a small value we introduce a small idling current in the output devices. This current is normally
in the order of milliamps. What this does is causes the output devices to
conduct for slightly more than the 180 degrees. Depending on the amount
of idle current introduced this may be up to 200 degrees and more. Technically the output stage runs in class A up to a very small power output.
Class A-B amplifiers are just a variation of a class B amplifier as
described above. Most amplifiers made today are A-B simply because a
pure class B would be unacceptable for audio owing to its high distortion at
crossover. Otherwise the two are identical.
Class D amps are Pulse Width Modulated switching power supplies
where the modulation is the audio signal. Typically a high frequency carrier (50KHz-500KHz) is converted to a triangle waveform. This triangle
waveform is fed into a comparator together with the incoming audio signal.
The resultant PWM waveform is fed into an output stage which alternately
switches either the positive switches on or negative switches on depending
on the polarity of the incoming waveform. Since the Mosfet switches are
either on or off, their efficiency is close to 100%. What little efficiency it
looses in the Mosfets are due to their finite on resistance and the losses
which occur during their transition from off to on and back to off states.
The high frequency pulse train must then be demodulated back to an
analog form in order that the loudspeaker can reproduce it. This is done
with a passive L-C filter whose cut off frequency is normally higher than the
highest audio frequency the amplifier is being asked to reproduce. So in a
20Hz-20KHz amplifier a 25-30KHz cut off filter would be used. Feedback is
nearly always implemented to get the distortion low, the output impedance
low and the noise low.
Amplifier Class Hierarchy
Performance
Value
RCP $3899 per pair
lack of distortion in the low frequencies makes for a very fast and
dynamic bass quality. The decay is somewhat less obvious, but
if you would listen carefully to, say a solo cello performance, you
would be most impressed with the level of energy in the bass frequencies, I can say for certain, the dying harmonics of the notes
decays in a natural and uncoloured manner.
Perhaps the only bugbear for one not familiar with typical
Class D amplifiers is the relative lack of ‘excitement’. They sound
too clean, too natural and so effortless that it almost begs for
something to stir the still waters. The D-200 instead deftly avoids
the non-persona of typical Class D amps for something is quite
likeable, quite musical (hah! There, I
said it!) and pretty nice to listen to. If
you are looking for something to impress in terms of sheer dynamics or
warm midrange, there are ‘better’
amps to be had. The question is, can
you live with such an amplifier?
The D-200 is not the first and
you can bet there will be more of
such amplifiers. Much has been said
of the D-200 performance can rival
that of amplifiers costing 4 times as
much. Either we have a lot of over priced amplifiers out there or
the D-200 is pretty exceptional for its asking price. Perhaps the
reality lies somewhere in between.
Loading...