Chungear Co CE10703 User Manual

CEILING FAN REMOTE CONTROLLER

OPERATION AND INSTALLATION INSTRUCTIONS

(Please keep this instruction pamphlet.)

IMPORTANT
YOU MUST SET CEILING FAN MANUAL SWITCH TO HIGH SPEED AND LIGHT
KIT (IF ANY) TO ON POSITION BEFORE OPERATING REMOTE CONTROL.

IMPORTANT POINTS TO REMEMBER:

1. Read and save these instructions.

2. Please note that all fixed wiring appliances should be installed by a qualified electrician.

3. The supply to the remote control receiver should be connected through a mains switch, i.e. existing wall
switch.

4. Disconnect from power supply at wall switch before working on remote control receiver or ceiling fan.

5. Install receiver into the ceiling fan canopy of the fan to ensure proper protection.

6. This unit is to be used for the control of ceiling fan and in an AC240V 50HZ power supply only.

7. Do not install in damp locations or immerse into water. (For indoor use only.)

8. Do not pull on or cut leads shorter.

9. Do not drop or bump the unit.

10. PLEASE NOTE: The battery will weaken with age and should be replaced before leaking takes place as this

will damage the transmitter. Dispose of used battery properly, keep the battery out of reach of children.

11. CAUTION: To reduce the risk of fire or injury, do not use this product in conjunction with any variable (rheostat)

wall control.

INSTALLATION INSTRUCTIONS

CAUTION: INCORRECT WIRE CONNECTION WOULD DAMAGE THIS RECEIVER.

1. Ceiling fan must be set at HIGH speed and light kit (If any) at ON position by pulling the “Pull Switch” after
installation.

2. Once the connection has been made, the receiver inserts into the drop rod hanging bracket. The canopy
comes up to cover the receiver and bracket.

LEARNING PROCESS

1~3seconds.

1. After installing the unit and power on, open battery cover (with battery, DC1.5V/

AAA*2pcs, installed), use a ball pen to press and hold the ”LEARN” key
FAN will be turn off and then FAN turn ON at medium speed, which indicate that
learning process finished. Please note that must press the “LEARNING KEY” within
30 seconds after power on. If just replace batteries, no need to re-learn.

2.

Please note that the transmitter can learn in multiple receiver, when doing learning
process please make sure not learn in other receiver.

FUNCTIONS OF TRANSMITTER

HI :Turn on the fan at high speed
MED : Turn on the fan at medium speed
LOW : Turn on the fan at low speed
OFF : Turn off the ceiling fan.
LIGHT ON/OFF: Press and release immediately to turn on or off the light

Ceiling Fan Remote Control

Wiring Connection

TR96C

Installation of transmitter wall
mount holder with two screws.

To assure continued FCC compliance:

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:

--Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the

equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an
experienced radio/TV technician for help.

CAUTION:

Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate
the equipment.

FCC ID：KUJCE10703

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.

IC：10786A-TR96C

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.

French:

Cet appareil radio est conforme au CNR d’Industrie Canada. L’utilisation de ce dispositif est autorisée seulement aux deux

conditions suivantes : (1) il ne doit pas produire de brouillage, et (2) l’utilisateur du dispositif doit être prêt à accepter tout

brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.