Chungear Co CE10507 User Manual
DC POWER CEILING FAN REMOTE CONTROL MANUAL
Step:
1.Install
the
1.5V/AAA
2pcs
batter
ies.
Within
30seconds
of
turning
the
Receivers
AC
power
ON.
Press
the
transmitter
’s“
LEARN
”
button.
Step:
2.Hold
the“LEARN
”
button
for
over
5
seconds,
once
the
receiver
has
detected
the
frequency,
the
receiver
will
make
sound,
Bi
Bi,
frequency
that
was
previously
selected
on
the
transmitter
.NOTE
:
After
theACpower
is
on,donot
press
any
other
button
on
the
transmitter
before
pressing
the“LEARN
”
button
,
Because
doing
so
will
cause
the
procedure
to
fail.After
completing
the
steps
above,
you
should
be
able
to
operate
the
ceiling
fan
and
light.
If
the
fanisnot
responding
to
the
transmitter,
NOTE
:
Remove
the
battery
if
not
used
for
long
periods
of
time
to
prevent
light
TR249A
LEARNING PROCESS
NOTE: The Hand Held Remote Control System is equipped with a learning frequency function which has
code combinations to prevent potential interference from other remote units.
twice. This will indicate the receiver has learned the
please turn the power off to the receiver. And repeat step 1 and 2.
damage to the hand held remote.
LIGHT FUNCTION SELECT SWITCH
If installed energy light onto ceiling fan, please slide the “light function select switch” to “O” position. If installed tungsten
light onto ceiling fan, please slide the “light function select switch” to “D” position.
FUNCTIONS OF TRANSMITTER
1. FAN SPEED：
1: Turn on ceiling fan at 1st speed (lowest speed)
2. Turn on ceiling fan at 2nd speed
3. Turn on ceiling fan at 3rd speed
4. Turn on ceiling fan at 4th speed
5. Turn on ceiling fan at 5th speed
6. Turn on ceiling fan at 6th speed (high speed)
: Turn off ceiling fan.
2. FAN TIMER: When the fan turned on.
2H ：Setting up that the ceiling fan will turn off after 2 hours automatically.
4H ：Setting up that the ceiling fan will turn off after 4 hours automatically.
8H ：Setting up that the ceiling fan will turn off after 8 hours automatically.
Press button can cancel fan timer setting.
3. --“F/R” :Hold this button 2 seconds to set fan wind direction up or down.
4. -- Natural breeze: Fan speed will modulate to simulate a natural breeze.
Press and turn the light on or off. DIMMER-Press and hold to dim or brighten
to the desired level and release.
(Tungsten only and light function select switch on “D” position.)
5. Installation of Transmitter Wall Mount Holder with Two screws.
To assure continued FCC compliance:
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the
equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an
experienced radio/TV technician for help.
CAUTION:
To assure continued FCC compliance:
Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate
the equipment.
FCC ID：KUJCE10507
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
Loading...