Chronomite SR 6240W, SR 8310W User Manual
®
SR-30 / 208 30 208 6240 0.65 43 34 28
SR-30 / 240 30 240 7200 0.65 49 39 33
SR-30 / 277 30 277 8310 0.65 57 45 38
SR-40 / 208 40 208 8320 0.65 57 45 38
SR-40 / 240 40 240 9600 0.65 66 52 44
TEMP RISE @
1.25 GPM
TEMP RISE @
1.50 GPM
MODEL AMPS VOLTS WATTS
TEMP RISE @
1.00 GPM
ACTIVIATION
GPM
INSTANT-FLOW SR - STANDARD FLOW
APPLICATION: commercial, industrial,
residential, lavatory, shower, kitchen/bar sink,
service sink, scrub sink
PRODUCT FEATURES
Unlimited hot water
â
Saves water and energy - 99% energy efficient
â
Vandal resistant rugged cast aluminum housing
â
Space saving compact size:
â
6-1/4" (H) x 9-5/8" x 2-3/4"
Meets applicable building codes
â
including ADA, UL, IAPMO,UPC.
Environmentally friendly
â
Made in the U.S.A.
â
Instant-Flow SR - Standard Flow
®
Chronomite Instant-Flow SR- Standard Flow models are
®
manufactured to provide reliable point-of-use hot water.
There is no pressure and temperature relief valve
needed (unless required by code), saving time and
money on installation.
Housing is fabricated from
rugged cast aluminum alloy.
Element assembly is fabricated from Celcon plastic.
Heating coils are nichrome.
Faucet flow controls and compression fittings are
supplied with each unit.
Member of
U.S.Green
Building Council
For the model being selected, please place the
corresponding amps, volts and temperature rise values
in the Guide Specifications to the right.
Water
Conserving
Product
Made in
the USA
GUIDE SPECIFICATION
Tankless Water Heater shall be a Chronomite
Laboratories Model
SR - _______ / _______
AMPS VOLTS
with Amps and Volts
to heat 1.0 gpm at a temperature rise of
°F
Unit shall be provided with Celcon waterways, and
Nichrome heating coils
OPTIONS
PA 765 ABS Housing (P)
m
Satin Finish Stainless Steel Housing (SS)
m
High Polish Finish Stainless Steel (SSP)
m
Pressure & Temp Relief Valve Assembly (TP)
m
_____
OPTIONS
Complies
with
Standards
for:
17 45 1 Hu rl ey St. :: Ci ty of In du st ry, CA 9 17 44 U.S .A .
Ph on e 80 0- 44 7- 49 62 :: 62 6- 93 7- 42 70
Fa x 62 6- 93 7- 42 79 :: ww w.c hr on om it e. co m
IFSR 04/01/14
®
INSTANT-FLOW SR - STANDARD FLOW
TECHNICAL DIMENSIONS
INSTANT-FLOW SR - STANDARD FLOW
Dimensions: 6-1/4" (H) x 9-5/8" x 2-3/4"
Weight: 5 lbs.
Materials: Rugged cast aluminum housing
Housing Color: White
Minimum Operating Flow Rate: 0.65 GPM
Minimum Operating Pressure: 25 PSI
Maximum Operating Pressure 150 PSI
Maximum Operating Temperature: 140°F
Listing: UL, IAPMO, UPC, ADA
GENERAL NOTES:
— 240V models when operated at 220V will have approximately a 15%
temperature decrease.
— 120V models when operated 110V will have approximately a 15%
temperature decrease.
— Per UL/IAPMO unit may not exceed maximum operating
temperature of 140°F
®
Celcon plastic element assembly
with nichrome coils
1/4"
1/4"
Chronomite Laboratories, Inc.
City of Industry, CA 91744 U.S.A.
5-3/4"
Front Service Panel
1-5/16"
1-1/8"
ø 3/16", 4 Mounting Holes
9-5/8"
2"
3-5/16"
Rear Electrical Knock-Out
ø 1" Access Hole
2-3/4"
1-1/8"
10-1/8"
2-3/4"
HOT
COLD
6-1/4"
INSTALLATION DIAGRAM
WIRING CONNECTION
Note: Heater to be
installed below the level
of all hot water outlets
serviced by the heater
3/8"
Cold Water
Faucet Feed
3/8" Hot Water Outlet
Compression
Instant-Flow
Heater
J-Box
Fittings (2)
HOT
COLD
5/8" x 3/8" x 3/8"
Three Way Angle
Stop Valve
3/8" Cold Water Inlet
Mounting Flanges (4)
Chronomite Laboratories assumes no responsibility for use of void or suspended data. © Copyright Chronomite Laboratories, Inc.
Member of Morris Group International, City of Industry, CA Please visit www.chronomite.com for most current specifications.
Company_______________________________________________________________________________________________________
Hot or
Neutral
Conduit
Refer to local
code for wire size
ATTENTION:
Unit must be hard wired.
NOTE: Heaters are single phase.
All tests are measured at
the output of the heater.
Hot
"GRD" is
earth
ground.
Model Number & Options_____________________________________________________________________Quantity_______________
Contact_________________________________________________Title____________________________________________________
Signature
& APPROVAL FOR
MANUFACTURING
(Approval for
Manufacturing)__________________________________________________________________Date ____________________________
SELECTION SUMMARY
PH. 800-447-4962
626-937-4270
FAX 626-937-4279
www.chronomite.com
IFSR 04/01/14
Loading...