Chromalox STAR-06A, STAR-05A, STAR-14A User Manual
(Supersedes PG435 )
PG435-1
VTS
161-304901-003
NOVEMBER, 2003
4
DATE
SALES
REFERENCE
DIVISION SECTION
Chromalox
®
STAR-05A, -06A and -14A Cart Kit
For Conversion of Fixed Style to Portable Style
© 2010 Chromalox, Inc.
STAR-06A Fixed Heater
Before Conversion
See Page 3 – Fig. 1
STAR-14A Fixed Heater
Before Conversion
See Page 4 – Fig. 1
STAR-05 Portable Heater
After Conversion
See Page 2 – Fig. 2
STAR-06A Portable Heater
After Conversion
See Page 3 – Fig. 2
STAR-14A Portable Heater
After Conversion
See Page 4 – Fig. 2
STAR-05A Fixed Heater
Before Conversion
See Page 2 – Fig. 1
4.5 kW FIXED STYLE HEATER
3
6
5
4.5 kW FIXED STYLE HEATE
R
6
FRONT VIE
W
BACK VIE
W
UPPER BRACKET
3/8 X 1-1/2"
BOLT WITH
LOCKWASHER
AND NUT
FRONT VIE
W
SIDE VIE
W
4 5/1
8 3/4"
9"
10 1/2
"
8
9
1
0
BACK VIEW
2
INSTRUCTIONS FOR CONVERTING
A FIXED STYLE INTO A PORTABLE STYLE
(Installation of Cart making it a Portable Heater Voids UL Listing)
1. The kit (168-053169-079) that converts a 4.5 KW fixed style radi-
ant heater into a portable includes the following parts. Verify that
all parts are included, if not, contact the Chromalox Service
Department at 1-800-368-2493.
(1)Lower Leg Assy. (7) 3/8-16 x 1-1/2” Long Bolts (4 Req’d)
(2)Upper Handle (8) 3/8-16 Nuts (2 Req’d)
(3)Front Leg (9) 3/8 Lockwashers (4 Req’d)
(4)Grip (10) 10-32 x 1/2” Long Self Tapping
(5)Grille Screw (2 Req’d)
(6)Cross Brace
2. Loosen nuts on upper bracket and remove bracket. Bolts, lock-
washers and nuts will be reused, but upper bracket can be disregarded.
3. Using the bolts, lockwashers and nuts removed in step 3, slide
one of the bolts in the extrusion grove to the 4-5/16” dimension
and one 3/8” bolt to the 8-3/4” dimension.
4. Place the cross brace (7) on the bolt and secure i n place using
the lockwashers and nuts provided.
5. Place lower leg assy. (1) onto brace and upper 3/8” bolts. Slide
the 3/8-16 x 1-1/2” long bolts through the cross b race (7) and the
lower leg (1). Secure in place with lockwashers and nuts provided.
6. Slide the two (2) 3/8-16 x 1-1/2” long bolts into the top center
extrusion. Locate one at 3/4” and the other at 2-1/4” as shown.
7. Place upper handle (3) onto two (2) bolts. Secure in place with
washers and nuts provided.
8. Slide grip (7) onto end of upper handle (5).
9. Stand heater vertically. If heater does not sit evenly, loosen nuts
that secure lower leg assy and adjust accordingly.
10.Rotate heater back until handle (3) is on floor.
11.Install front leg (4) with two 10-32 x 1/2” long self tapping
screws (11).
12.Snap grille (6) into lip of extrusion.
4.5 kW UNIT CONVERSION INSTRUCTIONS
Loading...