Chromagic Technologies HSM02 User Manual

HSM02 DOOR/WINDOW DETECTOR

The Door/Window Detector is a Z-Wave
with any Z-Wave
Z-Wave

TM

logo can also be used with it regardless of the manufacturer, and ours

TM

enabled network. Z-WaveTM enabled devices displaying the

can also be used in other manufacturer’s Z-Wave
of this Door/Window Detector on other manufacturer’s Wireless Controller menu
allows remote turn-on of connected modules and their connected lighting when the
Detector is triggered.

TM

enabled device and is fully compatible

TM

enabled networks. Inclusion

Trough association, device can be assigned as master/slave, and specify
which slave is going to be controlled by which master.

Reset Restore Detector to factory default.

The table below lists an operation summary of basic Z-Wave functions. Please
refer to the instructions for your Z-Wave

TM

Certificated Primary Controller to access

the setup function, and to include/exclude/associate devices.

Function Description LED Indication

No node ID The Z-Wave Controller does not allocate

a node ID to the unit.

Inclusion

Exclusion

Reset

1. Have Z-Wave Controller entered
inclusion mode.

2. Pressing tamper switch three times
within 1.5 second will enter inclusion
mode.

1. Have Z-Wave Controller entered
exclusion mode.

2. Pressing tamper switch three times
within 1.5 second will enter
exclusion mode.

1. Press tamper switch three times
within 1.5 second.

2-second on, 2-second
off

LED lights up once
whenever tamper switch
is pressed once.

Include to or Exclude from a Z-WaveTM Network

In the rear casing, there is a tamper switch which is used to carry out inclusion,
exclusion or reset. When power is first applied, its LED flashes on and off
alternately and repeatedly at 2-second intervals. It implies that it has not been
assigned a node ID and cannot work with Z-Wave enabled devices. The Detector
will stay “awake” for 5 minutes when power is first applied to allow time for
configuration. Please get familiar with the terms below before starting the
operations.

Function Description

Inclusion Add a Z-Wave enabled device (e.g. Detector) to Z-Wave network.
Exclusion Delete a Z-Wave enabled device (e.g. Detector) from the network.
Association After inclusion, you have to define the relationshipbetween devices.

2. Within 1 second, press and hold the
tamper switch until LED is off.

3. IDs are excluded and all of preset
value will be reset to factory default.

1. Have Z-Wave Controller entered
association mode.

2. When pressing tamper switch three
times within 1.5 second, the unit will
emit the NIF which implies that the
unit has entered association mode.

LED keeps on before
reset function has been
completed.
2-second on, 2-second
off

Association

Including a node ID allocated by Z-Wave Controller means inclusion. Excluding a node

ID allocated by Z-Wave Controller means exclusion.

Failed or success in including/excluding the node ID can be v iewed from the Z-Wave

Controller.

1

Choosing A Mounting Location

The Door/Window Detector is suitable for mounting in dry interior locations only.
Decide which doors/windows are to be protected by Door/Window Detectors,

(usually the front and back doors as a minimum will have Door/Window Detectors
fitted). Additional detectors may also be fitted where required to other vulnerable
doors or windows, (e.g. garage, patio/conservatory doors etc).

Note: Take care when fixing the Detect or to a met al frame, or mou nting within 1m of
metalwork (i.e. radiators, water pipes, etc) as this could affect th e radio range of the
device. If required, it may be necessary to space the magnet and detector away
from the metal surface using a plastic or wooden spacer to achieve the necessary
radio range.

Installation

1. Ensure that the system properly powered.
Factory default built in a CR2450 battery inside the detector and uses a Mylar
film to isolate battery from electric circuit of the detector. Remove the battery
Mylar film when ready to let the detector work.
If there is no battery inside the detector or need to replace a new battery please
insert the battery in 45° angle as below figure

2. Using the adhesive tape to fit detector on the door or window.

3. Fit the magnet to the moving part of the door/window opposite the detector
using the adhesive tape.

4. Ensure that the parallel gap between the magnet and detector is less than
20mm and that the matching line on the magnet is pointing towards and aligned
with the line on the detector. An alarm condition will be occurred if the gap is
greater than 35mm.

5. Remove the battery cover with the tamper switch not being pressed on the
detector (test mode), detach or close the magnet from the Detector, the LED on
the detector will illuminate.

6. After proper installation and test, put the battery cover back to the detector and
the detector enters the normal mode.

Note: After removing batteries, wait for 5 seconds to refit batteries.

Operation

1. The unit will stay “awake” for 5 minutes when power is first supplied to allow
time for configuration.

2. After the unit stays in sleep status, it can be woken up by pressing the tamper
switch continuously until the LED lights up once. The unit will enter sleep status
again after 10 seconds. If longer awake is desired, press tamper switch three
times within 1.5 seconds will prolong its awake period to 5 minutes.

3. With the tamper switch not being pressed, the unit enters test mode, which

allows the user to make a test. Detach the magnet from the Detector, the red
indicator LED on the Detector will illuminate.

4. When the tamper switch is pressed, the unit enters normal mode and the red

indicator LED on the Detector will not illuminate to conserve battery life when
the detector is triggered, (unless the battery is low).

2