Chroma Studio One 100 V User Manual

Chroma-Q®

Studio One 100 V™

User Manual

Version 1.0 September 2015, Software Version 1.6

PN: 638-0702

Studio One 100 V User Manual 1 V1.0 September 2015

www.chroma

-

q.com

Warranty Statement

Chroma-Q warrants to the original purchaser, with proof of purchase, that its delivered products shall be free from defects in

material and workmanship under normal use for a period of 12 months from date of shipment.

Chroma-Q will repair, or at its option, provide an equivalent item or replace, the defective product during the stated warranty

period. This warranty applies only to the repair or replacement of the product and only when the product is properly handled,

installed and maintained according to Chroma-Q instructions. This warranty excludes defects resulting from improper

handling, storage, installation, acts of God, fire, vandalism or civil disturbances. Purchaser must notify Chroma-Q in writing

within 14 days of noticing the defect. This warranty excludes field labour or service charges related to the repair or replacement of the product.

The warranty contained herein shall not extend to any finished goods or spare parts from which any serial number has been

removed or which have been damaged or rendered defective (a) as a result of normal wear and tear, wilful or accidental

damage, negligence, misuse or abuse; (b) due to water or moisture, lightning, windstorm, abnormal voltage, harmonic

distortion, dust, dirt, corrosion or other external causes; (c) by operation outside the specifications contained in the user

documentation; (d) by the use of spare parts not manufactured or sold by Chroma-Q or by the connection or integration of

other equipment or software not approved by Chroma-Q unless the Customer provides acceptable proof to Chroma-Q that

the defect or damage was not caused by the above; (e) by modification, repair or service by anyone other than Chroma-Q,

who has not applied for and been approved by Chroma-Q to do such modification, repair or service unless the Customer

provides acceptable proof to Chroma-Q that the defect or damage was not caused by the above; (f) due to procedures,

deviating from procedures specified by Chroma-Q or (g) due to failure to store, install, test, commission, maintain, operate or

use finished goods and spare parts in a safe and reasonable manner and in accordance with Chroma-Q’s instructions (h) by repair or replacement of engines without factory training.

The warranty contained herein shall not apply to finished goods or spare parts which are sold “as is”, as “second-hand”, as

used”, as “demo” or under similar qualifications or to Consumables (“Consumables” is defined as any part(s) of goods or

part(s) for use with goods, which part(s) of goods or part(s) for use with goods are consumed during the operation of the

goods and which part(s) of goods or part(s) for use with goods require replacement from time to time by a user such as, but not limited to, light bulbs).

The warranty contained herein shall not apply, unless the total purchase price for the defective finished goods or spare parts

has been paid by the due date for payment.

The warranty contained herein applies only to the original purchaser and are not assignable or transferable to any

subsequent purchaser or end-user.

This warranty is subject to the shipment of the goods, within the warranty period, to the Chroma-Q warranty returns

department, by the purchaser, at the purchasers’ expense. If no fault is found, Chroma-Q will charge the purchaser for the subsequent return of the goods.

Chroma-Q reserves the right to change the warranty period without prior notice and without incurring obligation and expressly disclaims all warranties not stated in this limited warranty.

Studio One 100 V User Manual 2 V1.0 September 2015

www.chroma

-

q.com

Disclaimer

The information contained herein is offered in good faith and is believed to be accurate. However, because conditions and

methods of use of our products are beyond our control, this information should not be used in substitution for customer's

tests to ensure that Chroma-Q products are safe, effective, and fully satisfactory for the intended end use. Suggestions of

use shall not be taken as inducements to infringe any patent. Chroma-Q sole warranty is that the product will meet the sales

specifications in effect at the time of shipment. Your exclusive remedy for breach of such warranty is limited to refund of

purchase price or replacement of any product shown to be other than as warranted.

Chroma-Q reserves the right to change or make alteration to devices and their functionality without notice due to our ongoing research and development.

The Chroma-Q Studio One 100 range has been designed specifically for the lighting industry. Regular maintenance should be performed to ensure that the products perform well in the entertainment environment.

If you experience any difficulties with any Chroma-Q products please contact your selling dealer. If your selling dealer is

unable to help please contact support@chroma-q.com. If the selling dealer is unable to satisfy your servicing needs, please

contact the following, for full factory service:

Outside North America: North America:

Tel: +44 (0)1494 446000 Tel: 416-255-9494

Fax: +44 (0)1494 461024 Fax: 416-255-3514

support@chroma-q.com support@chroma-q.com

For further information please visit the Chroma-Q website at www.chroma-q.com.

Chroma-Q and Studio One 100 V are trademarks, for more information on this visit www.chroma-q.com/trademarks.

The rights and ownership of all trademarks are recognised.

Important Notice:

As per the requirements in the Occupational Safety and Health Administration standards for product approval, please refer to

the OSHA web pages http://www.osha.gov/dts/otpca/nrtl/ for information on the list of Nationally Recognized Testing Laboratories (NRTLs) and the scope of recognition.

Studio One 100 V User Manual 3 V1.0 September 2015

www.chroma

-

q.com

Table of Contents

1.

1.1.

1.

Product overview

Product overviewProduct overview

Product overview ................................

................................................................

.................................... 4444

2.

2.2.

2.

Operation

OperationOperation

Operation ................................

................................................................

...........................................

......................

........... 5555

2.1 Unpacking the Units ....................................................................................................................................... 5

2.2 Cabling ......................................................................................................................................................... 5

2.3 Mounting ...................................................................................................................................................... 5

2.4 Optics ........................................................................................................................................................... 5

2.5 Control ......................................................................................................................................................... 6

2.6 DMX Protocol .............................................................................................................................................. 13

2.7 Thermal Performance .................................................................................................................................. 13

3.

3.3.

3.

Troubleshooting

TroubleshootingTroubleshooting

Troubleshooting ................................

................................................................

................................ 13

1313

13

4.

4.4.

4.

Specification

SpecificationSpecification

Specification ................................

................................................................

.....................................

..........

..... 14

1414

14

4.1 Technical Specifications ............................................................................................................................... 14

4.2 Drawings – Dimensions ............................................................................................................................... 15

5.

5.5.

5.

Ma

MaMa

Maintenance

intenanceintenance

intenance ................................

................................................................

.....................................

..........

..... 15

1515

15

Studio One 100 V User Manual 4 V1.0 September 2015

www.chroma

-

q.com

1. Product overview

The new Chroma

ChromaChroma

Chroma----Q® Studio One 100™

Q® Studio One 100™Q® Studio One 100™

Q® Studio One 100™ LED Par is designed to deliver the highest quality of white light from an LED

based fixture, for the most demanding applications.

Utilising core LED technology from the Chroma-Q premium performance lighting range, the multi-purpose fixture is ideal for a wide range of environments and provides a powerful, creative lighting tool.

The Studio One's custom optical design and fully homogenised output provides a smooth, uniform and defined 18° beam.

Theatrical grade dimming emulates the extremely smooth dimming curve of tungsten fixtures.

The Studio One 100 offers adjustable dimming frequencies to ensure flicker-free operation on cameras.

With the advanced feature set also including convection cooling for silent operation and a versatile mounting yoke, the Studio

One 100 is suitable for numerous TV, film, studio, exhibition & entertainment lighting applications - complementing the popular Chroma-Q Studio Force™ and Studio Force Phosphor™ LED fixtures ranges.

With a simple to use Infra-Red remote control included with each fixture, you can be up and running within minutes without

the requirement of a lighting console - saving time and labour with instant access to pre-set colour temperatures, on/off, dimming and effects.

To enable maximum flexibility with users' existing production inventory, the Studio One accepts industry-standard 6.25" accessories such as egg crates, barndoors and top hats.

Note: HANDHELD COLOUR METERS

• Handheld Colour Meters provide a limited measuring range for LED fixtures, which results in inconsistent and unreliable data.

• All photometric values listed in this document are based on testing and measurements conducted by certified independent laboratories with reference to the IES standards.

Studio One 100 V User Manual 5 V1.0 September 2015

www.chroma

-

q.com

2. Operation

2.1 Unpacking the Units

The Studio One 100 V package includes 1 unit fixture, power cord, power connector, colour frame, a Quick Start Guide and an IR Remote.

We recommend that you keep the original packaging in case the item needs to be returned.

2.2 Cabling

The Studio One 100 V is built with chassis mount powerCon connectors for power input and through; chassis mount XLR 5pin connectors for DMX control data input and through.

The enclosure is ground bonded.

XLR 5-pin Cable:

Power Cable:

Important Notice: The use of an opto-splitter for DMX signal distribution is highly recommended when several fixtures are

not plugged into the same power source.

2.3 Mounting

The Studio One 100 V is built with a split yoke system for floor mounting and overhead hanging applications. Secure the fixture with a safety bond when hung. A provision for a fixing hold is built into the fixture.

2.4 Optics

The Studio One 100 V is built with an optical lens that provides a fully homogenised beam angle of approximately ~ 18°.

Pin# Function

1 Ground (Screen) 2

Data Minus

3

Data Plus

4

Spare Data Minus

5

Spare Data Plus

International

Colour Code

North American

Colour Code

Connections

Green and Yellow Green Earth (E) Ground (Green) Blue White Neutral (N) Neutral (Silver) Brown Black Live (L) Hot (Gold)

Studio One 100 V User Manual 6 V1.0 September 2015

www.chroma

-

q.com

2.5 Control

The Studio One 100 V is controlled remotely via ANSI E1.11 USITT DMX512-A protocol or can operate as a standalone unit

with the wireless IR Remote. The control functions can be accessed through the LCD display at the rear of the fixture with 4

push buttons.

Back Arrow (Enter) Stores the menu choice

Up Arrow Increases (+) the mode level or value

Down Arrow Decreases (-) the mode level or value

Exit Back to the previous menu

Power-Up Display:

On power-up, the display shows the Brand, Model Name and Software Version for 5 seconds then goes on to show the Main

Menu. The Main Menu shows:

•

Model Name

•

DMX Status

•

DMX Address

•

Set Control Personality (Mode)

•

Number of Assigned Channels

Display Mode:

The LCD is backlit when you access the menus. This will switch off when left undisturbed for 10 seconds.

Personality:

The Studio One 100 V features a single Warm and Cold White LED engine which can be controlled through four Personality

modes:

Studio One 100 V User Manual 7 V1.0 September 2015

www.chroma

-

q.com

Display Ch Description

1-CTI 2 1 channel controls Color Temperature adjustment for all LEDs and 1 channel for Intensity control of all

LEDs. 2-WW CW 2 1 channel controls all Warm White LEDs and 1 channel controls all Cold White LEDs. 3-Master The unit is set as the Master unit. All settings of the Master unit will be repeated on all Slave units. 4-Slave The unit is set as the Slave unit. All settings of the Slave units follow the Master unit.

Wireless IR Remote:

The Studio One 100 V can be controlled via wireless IR Remote in standalone operation. The fixture is set in IR Remote

control by selecting IR Remote in the menu No DMX Present. Point the IR Remote towards the fixture.

The IR Remote features buttons for the following control options:

• On and Off

• Fade In and Out

• White

Color and Effects Buttons applicable to the Color One 100 units:

• 15 Colors

• 4 Effects: Full Color Scroll (Flash), Warm Color Scroll (Strobe),

• Fade In/Fade Out, and Cold Color Scroll (Smooth)

Studio One 100 V User Manual 8 V1.0 September 2015

www.chroma

-

q.com

Control Menu

•

Use the Up

UpUp

Up and Down

DownDown

Down arrows to navigate the control menu options

•

Press Enter

EnterEnter

Enter to select a control menu option

•

Press Enter

EnterEnter

Enter to save the setting, display shows Done and returns to the previous menu

•

Press Exit

ExitExit

Exit to return to the previous menu without saving

•

The display goes back to the Main Menu

Studio One 100 V User Manual 9 V1.0 September 2015

www.chroma

-

q.com

Main Menu

The Main Menu displays the following:

• Model name

• DMX status

• DMX start address

• Personality (Control Mode)

• Number of assigned channels

To set the DMX start address,

1. From the Main Menu, press Enter

EnterEnter

Enter....

2. Press Up

UpUp

Up or Down

DownDown

Down to adjust the DMX start address.

3. Press Enter

EnterEnter

Enter to save.

Display shows Done and returns to the Main Menu.

1-Personality

The Studio One 100 V can be set to operate in DMX controlled and standalone modes. Refer to the list below for details.

To set the Personality,

1. From the Main Menu, press Up

UpUp

Up or Down

DownDown

Down to access 1-Personality.

2. Press Enter

Enter Enter

Enter and then Up

UpUp

Up or Down

DownDown

Down to select the mode.

3. Press Enter

EnterEnter

Enter to save.

The display shows Done, returns to 1-Personality and then the Main Menu.

Personality – Software Version 1.6

Display Ch Description

1-CTI 2 Color Temperature + Intensity

2-WW CW 2 Warm White + Cold White

3-Master 0 Set as master unit in standalone

4-Slave 0 Set as slave unit in standalone

Studio One 100 V User Manual 10 V1.0 September 2015

www.chroma

-

q.com

2-No DMX Present

If DMX control signal from an external source is not detected, various standalone output options can be selected:

1-OFF Fixture has no light output

2-Hold Last Fixture holds the last valid DMX state

3-IR Remote Fixture is controlled via remote infrared control unit

4-Look 1 Fixture snaps to saved Look

5-Look 2 Fixture snaps to saved Look

6-Look 3 Fixture snaps to saved Look

7-Look 4 Fixture snaps to saved Look

8-Look 5 Fixture snaps to saved Look

To set the option when there is No DMX Present,

1. From the Main Menu, press Up

UpUp

Up or Down

DownDown

Down to access 2-No DMX Present.

2. Press Enter

EnterEnter

Enter, then press Up

Up Up

Up or Down

DownDown

Down to select the option.

3. Press Enter

EnterEnter

Enter to save.

The display shows Done, returns to 2-No DMX Present and then the Main Menu.

Studio One 100 V User Manual 11 V1.0 September 2015

www.chroma

-

q.com

3-Look Store

In this mode,

•

5 internal preset Looks are available for stand-alone operation (see No DMX Present).

•

Looks created from an external DMX console can be recorded in any of the 5 Look numbers and will be preserved on power down.

•

Looks that have been recorded can be modified in stand-alone operation.

•

Looks will be returned to default setting if reset is performed.

To recall a Look in stand-alone operation,

1. From the Main Menu, press Up

UpUp

Up or Down

DownDown

Down to access 3-Look Store.

2. Press Enter

EnterEnter

Enter and press Up

UpUp

Up or Down

DownDown

Down to select from Look 1 to 5.

3. Press Up

UpUp

Up or Down

DownDown

Down to increase or decrease the color temperature “CT

CTCT

CT” and intensity “IIII” from 0 to 100.

4. Press and hold Enter

EnterEnter

Enter to save the Look, the display shows Recorded and the Look turns On.

To record a Look created from a remote DMX console:

1. Set the fixture to the desired Personality.

2. Use an external DMX console to adjust the assigned channel levels and create the desired look or effect.

3. From the Main Menu, press Up

UpUp

Up or Down

DownDown

Down to select 3-Look Store

4. Press Enter

EnterEnter

Enter, press Up

UpUp

Up or Down

DownDown

Down to select the Look number and the display shows Record?

5. Press Enter

EnterEnter

Enter to record the Look and the display shows Recorded.

To create or modify a Look in stand-alone operation:

1. From the Main Menu, press Up

UpUp

Up or Down

DownDown

Down to select 3-Look Store

2. Press Enter

EnterEnter

Enter, press Up

UpUp

Up or Down

DownDown

Down to recall the Look number

3. Press Enter

EnterEnter

Enter and the display shows “CT” and “I” (Color Temperature and Intensity) at the top row and the

value below

4. Press Up

UpUp

Up or Down

DownDown

Down to increase or decrease the Intensity value.

5. Press and hold Enter

EnterEnter

Enter until the display shows Recorded.

Studio One 100 V User Manual 12 V1.0 September 2015

www.chroma

-

q.com

4-Technical

In this mode,

•

Software Version is displayed

•

DMX Data (value) of the channels are displayed

•

Internal temperature is displayed

•

The fixture can be set to 4 frequency options. The LED scan rate can be synchronised with the video camera to avoid a flickering effect.

Frequency options:

750 Hz 1500 Hz 3000 Hz 6000 Hz

•

Calibration data of the channels are displayed

To display the Software Version,

1. From the Main Menu, press Up

UpUp

Up or Down

DownDown

Down to access 4-Technical

2. Press Enter

EnterEnter

Enter, the display shows the Software Version

To display DMX Data,

1. From the Main Menu, press Up

UpUp

Up or Down

DownDown

Down to access 4-Technical

2. Press Enter

EnterEnter

Enter, Up

UpUp

Up or Down

DownDown

Down and select DMX Data

3. Press Enter

EnterEnter

Enter, the display shows the DMX channel value

To display the temperature of the LED Engine in the fixture,

1. From the Main Menu, press Up

UpUp

Up or Down

DownDown

Down to access 4-Technical

2. Press Enter

EnterEnter

Enter, Up

UpUp

Up or Down

DownDown

Down and select Temperature

3. Press Enter

EnterEnter

Enter, the display shows the LED Engine Temperature

To set the Frequency,

1. From the Main Menu, press Up

UpUp

Up or Down

DownDown

Down to access 4-Technical

2. Press Enter

EnterEnter

Enter, Up

UpUp

Up or Down

DownDown

Down and select PWM Frequency

3. Press Enter

EnterEnter

Enter, Up

UpUp

Up or Down

DownDown

Down and select a frequency option

4. Press Enter

EnterEnter

Enter to save

The display shows Done and returns 4-Technical and then Main Menu.

To display the Calibration data,

1. From the Main Menu

Main MenuMain Menu

Main Menu, press Up

UpUp

Up or Down

DownDown

Down to access 4-Technical

2. Press Enter

EnterEnter

Enter, Up

UpUp

Up or Down

DownDown

Down and select Calibration

3. Calibration data of the channels are displayed

Studio One 100 V User Manual 13 V1.0 September 2015

www.chroma

-

q.com

5-Reset

To reset the fixture to the factory default settings,

1. From the Main Menu, press Up

UpUp

Up or Down

DownDown

Down to access 5-Reset

2. Press Enter

EnterEnter

Enter, display shows reset?

3. Press and hold Enter

EnterEnter

Enter for 2 seconds, display shows Hold for 2 sec. and Done after 2 seconds, then

back to the Main Menu.

All control menu commands are reset to factory defaults:

DMX address 1

Personality CTI

No DMX Present Hold Last

Look Store 1

PWM Frequency 750Hz

2.6 DMX Protocol

DMX Personality:

Studio

StudioStudio

Studio One

OneOne

One 100

100100

100 VVVV

V1.

V1.V1.

V1.6666

1-CTI

[2 ch]

2-WW CW

[2 ch]

Channel 1 Color Temperature Warm White

Channel 2 Intensity Cold White

Total 2 DMX channels 2 DMX channels

2.7 Thermal Performance

The internal cooling system of the Studio One fixture is by convection and built with automatic protection. The fixture’s

automatic protection reduces the output when the internal temperature reaches the maximum limit due to extreme ambient conditions.

3. Troubleshooting

Troubleshooting is a process of elimination. First, rule out the other field factors (i.e. bad connections, faulty cables and power supplies). For technical support and/or parts, please contact your selling dealer or the offices listed in this manual.

Symptom Possible Cause Solution

Fixture does not respond to DMX control.

Set to wrong or different DMX address. Bad cable connecting DMX control and fixture. Bad in/through connection between adjacent fixtures.

Check DMX address and Mode settings. Check/replace DMX run from the console.

Low LED output. Internal temperature is over the limit. Check area ventilation.

Studio One 100 V User Manual 14 V1.0 September 2015

www.chroma

-

q.com

4. Specification

4.1 Technical Specifications

Product Code CHSONE100V Net Dimensions**

(Without Fixings – W x H x D)

214mm x 267mm x 232mm / 8.5" x 10.5" x 9" (Full open yoke)

Net Weight (Without Fixings) 3.8 kg / 8.5 lb Shipping Dimensions – Width x Height x Depth

406mm x 228mm x 292mm / 16" x 9" x 11.5"

Shipping Weight 5.5 kg / 12 lb Power & Connections Power Supply Built-in Power Input Rating 100-240V AC 50-60Hz 125VA Power Factor 0.5 Power Consumption 58W @ 120/230V AC Idle Power Consumption 3.5W @ 120V AC; 5.6W @ 230V AC Inrush Current 15A @ 120V AC; 36A @ 230V AC Typical Power & Current Measurements done with all LEDs at maximum intensity. Measurements made at nominal

voltage. Allow for a deviation of +/- 10%. Power connector In/Out powerCon Data Connectors In/Out XLR 5-pin Control Protocol ANSI E1.11 USITT DMX 512-A Cooling System Convection Operating Temperature 0°C to 40°C Construction Cast machined aluminium

Colour Black (custom colours available on request) Built-In Hardware Split yoke, 6.25” Accessory Holder IP Rating IP20 Approvals CISPR 15/EN55015& EN61547, FCC Part 15 Subpart B:2012 /

ICES-003:2012, CSA C22.2, UL 1573, IEC 60598 Control & Photometric LED Engines 1 LEDs Per Engine Warm White + Cold White Control Modes 2 channels Color Temperature + Intensity, 2 channels Warm White + Cold White

Dimming Curve Theatrical Wireless Control On / Off, Fade In, Fade Out Hot Lumen Output 2,100 Optics Fully Homogenised Beam Angle 18° (approx) Beam Distribution Symmetrical direct illumination CCT 3,000K - 6,100K CRI 86 Lamp Life L70 at 50,000 hours

**

For exact measurements please refer to the line drawings below

Studio One 100 V User Manual 15 V1.0 September 2015

www.chroma

-

q.com

4.2 Drawings – Dimensions

5. Maintenance

With care, the Studio One 100 requires little maintenance. However, as the unit is likely to be used in a stage environment

we recommend periodical internal inspection and cleaning of any resulting dust and cracked oil residue. If the front enclosure requires cleaning, wipe with a mild detergent on a damp cloth.

Chroma Studio One 100 V User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual