Chroma Inspire User Manual

Chroma-Q®

Inspire™

User Manual

Version 1.4 May 2014, Software Version 2.1

PN: 632-0700

Inspire User Manual 1 V1.4 May 2014

www.chroma

-

q.com

Warranty Statement

Chroma-Q warrants to the original purchaser, with proof of purchase, that its delivered products shall be free from defects in

material and workmanship under normal use for a period of 12 months from date of shipment.

Chroma-Q will repair, or at its option, provide an equivalent item or replace, the defective product during the stated warranty

period. This warranty applies only to the repair or replacement of the product and only when the product is properly handled,

installed and maintained according to Chroma-Q instructions. This warranty excludes defects resulting from improper

handling, storage, installation, acts of God, fire, vandalism or civil disturbances. Purchaser must notify Chroma-Q in writing

within 14 days of noticing the defect. This warranty excludes field labour or service charges related to the repair or replacement of the product.

The warranty contained herein shall not extend to any finished goods or spare parts from which any serial number has been

removed or which have been damaged or rendered defective (a) as a result of normal wear and tear, willful or accidental

damage, negligence, misuse or abuse; (b) due to water or moisture, lightning, windstorm, abnormal voltage, harmonic

distortion, dust, dirt, corrosion or other external causes; (c) by operation outside the specifications contained in the user

documentation; (d) by the use of spare parts not manufactured or sold by Chroma-Q or by the connection or integration of

other equipment or software not approved by Chroma-Q unless the Customer provides acceptable proof to Chroma-Q that

the defect or damage was not caused by the above; (e) by modification, repair or service by anyone other than Chroma-Q,

who has not applied for and been approved by Chroma-Q to do such modification, repair or service unless the Customer

provides acceptable proof to Chroma-Q that the defect or damage was not caused by the above; (f) due to procedures,

deviating from procedures specified by Chroma-Q or (g) due to failure to store, install, test, commission, maintain, operate or

use finished goods and spare parts in a safe and reasonable manner and in accordance with Chroma-Q’s instructions (h) by repair or replacement of engines without factory training.

The warranty contained herein shall not apply to finished goods or spare parts which are sold “as is”, as “second-hand”, as

used”, as “demo” or under similar qualifications or to Consumables (“Consumables” is defined as any part(s) of goods or

part(s) for use with goods, which part(s) of goods or part(s) for use with goods are consumed during the operation of the

goods and which part(s) of goods or part(s) for use with goods require replacement from time to time by a user such as, but not limited to, light bulbs).

The warranty contained herein shall not apply, unless the total purchase price for the defective finished goods or spare parts

has been paid by the due date for payment.

The warranty contained herein applies only to the original purchaser and are not assignable or transferable to any

subsequent purchaser or end-user.

This warranty is subject to the shipment of the goods, within the warranty period, to the Chroma-Q warranty returns

department, by the purchaser, at the purchasers expense. If no fault is found, Chroma-Q will charge the purchaser for the subsequent return of the goods.

Chroma-Q reserves the right to change the warranty period without prior notice and without incurring obligation and expressly disclaims all warranties not stated in this limited warranty.

Inspire User Manual 2 V1.4 May 2014

www.chroma

-

q.com

Disclaimer

The information contained herein is offered in good faith and is believed to be accurate. However, because conditions and

methods of use of our products are beyond our control, this information should not be used in substitution for customer's

tests to ensure that Chroma-Q products are safe, effective, and fully satisfactory for the intended end use. Suggestions of

use shall not be taken as inducements to infringe any patent. Chroma-Q sole warranty is that the product will meet the sales

specifications in effect at the time of shipment. Your exclusive remedy for breach of such warranty is limited to refund of

purchase price or replacement of any product shown to be other than as warranted.

Chroma-Q reserves the right to change or make alteration to devices and their functionality without notice due to our on going research and development.

The Chroma-Q Inspire range has been designed specifically for the lighting industry. Regular maintenance should be performed to ensure that the products perform well in the entertainment environment.

If you experience any difficulties with any Chroma-Q products please contact your selling dealer. If your selling dealer is

unable to help please contact support@chroma-q.com. If the selling dealer is unable to satisfy your servicing needs, please

contact the following, for full factory service:

Outside North America: North America:

Tel: +44 (0)1494 446000 Tel: 416-255-9494

Fax: +44 (0)1494 461024 Fax: 416-255-3514

support@chroma-q.com support@chroma-q.com

For further information please visit the Chroma-Q website at www.chroma-q.com.

Chroma-Q and Inspire are trademarks, for more information on this visit www.chroma-q.com/trademarks.

The rights and ownership of all trademarks are recognised.

Important Notice:

As per the requirements in the Occupational Safety and Health Administration standards for product approval, please refer to

the OSHA web pages http://www.osha.gov/dts/otpca/nrtl/ for information on the list of Nationally Recognized Testing Laboratories (NRTLs) and the scope of recognition.

Inspire User Manual 3 V1.4 May 2014

www.chroma

-

q.com

Table of Contents

1.

1.1.

1. Product overview

Product overviewProduct overview

Product overview ................................

................................................................

....................................

........

.... 4444

2.

2.2.

2. Operation

OperationOperation

Operation ................................

................................................................

...............................................

..............................

............... 4444

2.1 Unpacking the Units ....................................................................................................................................... 4

2.2 Cabling ......................................................................................................................................................... 4

2.3 Mounting ...................................................................................................................................................... 5

2.4 Optional Inspire Ceiling Installation Kit ............................................................................................................. 5

2.5 Optics ........................................................................................................................................................... 6

2.6 Control ......................................................................................................................................................... 6

2.7 DMX Protocol – Inspire ................................................................................................................................ 11

2.8 Thermal Performance .................................................................................................................................. 13

3.

3.3.

3. Troubleshooting

TroubleshootingTroubleshooting

Troubleshooting ................................

................................................................

....................................

........

.... 13

1313

13

4.

4.4.

4. Specification

SpecificationSpecification

Specification ................................

................................................................

.........................................

..................

......... 13

1313

13

4.1 Technical Specifications ............................................................................................................................... 14

4.2 Drawings – Dimensions ............................................................................................................................... 15

5.

5.5.

5. Maintenance

MaintenanceMaintenance

Maintenance ................................

................................................................

.........................................

..................

......... 15

1515

15

6.

6.6.

6. Ceiling Installation Procedure

Ceiling Installation ProcedureCeiling Installation Procedure

Ceiling Installation Procedure ................................

................................................................

.................................................

..................................

................. 16

1616

16

Inspire User Manual 4 V1.4 May 2014

www.chroma

-

q.com

1. Product overview

The new Chroma-Q® Inspire™ LED house light is a powerful multi-purpose creative lighting tool that utilises some of the

innovative core technologies found in the incredibly popular Chroma-Q Color Force™ range. The Inspire provides a choice of

beautiful whites, soft pastels and bold saturates - all from one fixture. By incorporating industry standard DMX-512 control,

the Inspire is able to integrate seamlessly with an existing DMX infrastructure and can be controlled by any DMX supported

lighting console. With fully homogenised colour mixing and a choice of three different lens options, the Inspire provides an

excellent selection of stunning mixed colours and ‘true’ whites, with no unsightly colour separation shadows. It also features an energy-efficient compact LED design providing reduced maintenance and running costs.

The Inspire fixture is built with a single light engine featuring 36 high powered LEDs (combination of white, red, green and

blue). Each model is equipped with a built-in power supply and can operate as a standalone unit or be remotely controlled

through the ANSI E1.11 USITT DMX 512-A protocol. The control options incorporate a choice of multiple channel intensity

control, effects and a dynamic Variable Effects Engine integrated in the software, which gives the user full control of the effects combination.

The product's robust anodised aluminium extruded construction houses a discreet cable management system and additional

protection built around the optics.

Note: HANDHELD COLOUR METERS

Handheld Colour Meters provide a limited measuring range for LED fixtures, which results in inconsistent and unreliable data.

All photometric values listed in this document are based on testing and measurements conducted by certified independent

laboratories with reference to the IES standards.

2. Operation

2.1 Unpacking the Units

The Inspire package includes 1 unit Inspire fixture, power connector (EU) or power cord (US), safety chain and a Quick Start Guide. We recommend that you keep the original packaging in case the item needs to be returned.

2.2 Cabling

The Inspire fixture utilises a powerCon connector for power input. The DMX control data input and through connections from

an external control console are via two XLR 5-pin connectors. The chassis are ground bonded.

Inspire User Manual 5 V1.4 May 2014

www.chroma

-

q.com

XLR 5-pin Cable: Power Cable:

Pin# Function

1 Ground (Screen)

2 Data Minus

3 Data Plus

4 Spare Data Minus

5 Spare Data Plus

Important Notice: The use of an opto-splitter for DMX signal distribution is highly recommended when several fixture units are not plugged into the same power source.

2.3 Mounting

The Inspire fixture is equipped with a built-in mounting bracket for overhead hanging applications. Secure the fixture with a safety bond. A provision for a fixing hold is built into the fixture.

2.4 Optional Inspire Ceiling Installation Kit

The Inspire fixture can be mounted on a ceiling with the Inspire Ceiling Installation Kit, which consists of the following items:

(See Table & Drawing below; see Ceiling Installation Procedure on page 16 of this User Manual)

1 Trim Ring Inspire Black

2 Bracket Hook

3 T-Nut ¼-20” Economy 15S

4 Angle support ceiling mounting

5 Screw Flanged Button Socket ¼-20 x ¾”

6 Washer

Caution: The angle supports of the ceiling installation kit must be mounted or attached to the

The angle supports of the ceiling installation kit must be mounted or attached to the The angle supports of the ceiling installation kit must be mounted or attached to the

The angle supports of the ceiling installation kit must be mounted or attached to the ceiling with the

ceiling with theceiling with the

ceiling with the

appropriate load capacity.

appropriate load capacity.appropriate load capacity.

appropriate load capacity.

International

Colour Code

North American

Colour Code

Connections

Green and Yellow Green Earth (E) Ground (Green)

Blue White Neutral (N) Neutral (Silver)

Brown Black Live (L) Hot (Gold)

Inspire User Manual 6 V1.4 May 2014

www.chroma

-

q.com

2.5 Optics

The Inspire fixture can be built with either Narrow, Medium or Wide lens. The beam angles are:

2.6 Control

The Inspire fixture can operate as a standalone unit or be controlled remotely via ANSI E1.11 USITT DMX512-A protocol. The control functions can be accessed through the LCD display at the rear of the fixture with 4 push buttons.

Power-Up Display:

On power-up and home position, the display shows the Main Menu:

•

model name

•

software version

•

the DMX address

•

current assigned mode

•

number of assigned channels

Display Mode:

The LCD is backlit when you access the menus. This will turn off when left undisturbed for 5 seconds.

Control Modes:

The Inspire fixture consists of a single LED engine with a combination of 6 Red LEDs, 6 Green LEDs, 6 Blue LEDs and 18 Neutral White LEDs for a total of 36 LEDs.

Narrow ~ 32°

Medium ~ 42°

Wide ~ 65°

Exit: Back to previous menu

Exit: Back to previous menuExit: Back to previous menu

Exit: Back to previous menu

Up Arro

Up ArroUp Arro

Up Arro

w: Increases (+) the mode level or value

w: Increases (+) the mode level or valuew: Increases (+) the mode level or value

w: Increases (+) the mode level or value

Down Arrow: Decreases (

Down Arrow: Decreases (Down Arrow: Decreases (

Down Arrow: Decreases (

----

) the mode level or

) the mode level or) the mode level or

) the mode level or

value

value value

value

Back Arrow: (Enter) Stores the menu choice

Back Arrow: (Enter) Stores the menu choiceBack Arrow: (Enter) Stores the menu choice

Back Arrow: (Enter) Stores the menu choice

Inspire User Manual 7 V1.4 May 2014

www.chroma

-

q.com

No. Display Ch Description

1 fxHSI 7 4 x channels for Effects + Hue, Saturation, Intensity

2 sRGBW 5 1 x Intensity Effects Channel + Red, Green, Blue, White

3 HSI 3 Hue, Saturation & Intensity

4 RGBW 4 Red, Green, Blue, White

11 Look sel 1 Look Select (Effects engine, programmable presets and user programmed Looks)

12 Mastr StndAlon Assigns the unit as Master in standalone operation

13 Slave StndAlon Assigns the unit as Slave in standalone operation

Internal FX engine

: integrated in the software is an internal Fx engine with variable parameters to create an unlimited

amount of unique lighting effects.

Control Menu

•

Use the Up

UpUp

Up and Down

DownDown

Down arrows to navigate the control menu options

•

Press the Back

BackBack

Back arrow (Enter) to select a control menu option

•

Press and hold the Back

BackBack

Back arrow (Enter) to save the setting

•

Press Exit

ExitExit

Exit to return to the Main Menu

Inspire User Manual 8 V1.4 May 2014

www.chroma

-

q.com

Main Menu

The Main Menu displays:

•

Model name

•

Control software version

•

DMX start address

•

Control Mode

•

Number of channels

DMX Address

To set the DMX start address,

1. From the Main Menu, press Enter

EnterEnter

Enter

2. Press Up

UpUp

Up or Down

DownDown

Down to adjust DMX start address

3. Press Enter

EnterEnter

Enter for 2 seconds to save and return to the Main Menu.

Control Mode

The Inspire fixture can be set to operate in 5 DMX controlled modes and 2 standalone modes. Refer to the list below for details.

To set the Control Mode,

1. From the Main Menu, press Up

UpUp

Up or Down

DownDown

Down to access the Control Mode

2. Press Enter

Enter Enter

Enter and then Up

UpUp

Up or Down

DownDown

Down to select the mode

3. Press Enter

EnterEnter

Enter for 2 seconds to save

The display returns to Control Mode and then the Main Menu.

Control Mode - Software Version 2.1

Mode Display Ch Description

1 fxHSI 7 4 x Effects, Hue, Saturation, Intensity

2 sRGBW 5 Intensity Effects, Red, Green, Blue, White

3 HSI 3 Hue, Saturation, Intensity

4 RGBW 4 Red, Green, Blue, White

11 Look sel 1 Look Select

12 Mastr StndAlon Unit assigned as Standalone Master

13 Slave StndAlon Unit assigned as Standalone Slave

When DMX is Lost

If DMX is not detected, various output options can be selected:

OFF Fixture has no light output

HOLD Fixture holds the last valid DMX state

LOOK 01 – 31 Fixture snaps to the selected Look

To set the option When DMX is Lost,

1. From the Main Menu, press Up

UpUp

Up or Down

DownDown

Down to access When DMX is Lost

2. Press Enter

EnterEnter

Enter, then press Up

Up Up

Up or Down

DownDown

Down select the option

3. Press Enter

EnterEnter

Enter for 2 seconds to save

The display returns to When DMX is Lost and then the Main Menu.

Inspire User Manual 9 V1.4 May 2014

www.chroma

-

q.com

Look Store

The Inspire fixture has 31 internal preset FX Looks for standalone operation, 1-23 are pre-programmed.

To replay a Look in standalone operation,

1. From the Main Menu, press Up

UpUp

Up or Down

DownDown

Down to access Look Store

2. Press Enter

EnterEnter

Enter, press Up

UpUp

Up or Down

DownDown

Down to select a Look

3. Press Enter

EnterEnter

Enter for 2 seconds to save

The display returns to Look Store and then the Main Menu.

The fixture plays back the assigned Look.

To replay a Look with a DMX console,

1. From the Main Menu, press Up

UpUp

Up or Down

DownDown

Down to access Control Mode

2. Press Enter

EnterEnter

Enter, then press Up

UpUp

Up or Down

DownDown

Down to select Look sel

Look selLook sel

Look sel

3. Press Enter for 2 seconds to save

4. Use the external DMX console with the assigned DMX channel to playback the various looks stored. (1-31 looks in 1 single channel)

The display returns to Control Mode and then the Main Menu.

Note: DMX has priority over internal Looks

Recording user programmed Looks:

Looks can be recorded to the internal flash memory by users and will be preserved on power down. However, looks will be returned to default setting if Reset is performed. There are two ways to record a look:

Simple, with DMX console

1. Set the fixture to the desired Control Mode.

2. Use an external DMX console to adjust the channel levels and create the desired look or effect.

3. Press Up

UpUp

Up or Down

DownDown

Down to select Look Store

4. Press Enter

EnterEnter

Enter, press Up

UpUp

Up or Down

DownDown

Down to select the Look number

5. Press Enter

EnterEnter

Enter for 2 seconds to save the Look

Advanced, standalone (DMX is unplugged)

1. From the Main Menu, press Up

UpUp

Up or Down

DownDown

Down to select Look Store

2. Press Enter

EnterEnter

Enter, then press Up

UpUp

Up or Down

DownDown

Down to select a Look

3. Press Enter

EnterEnter

Enter to access the memory data. The data is presented as two numbers separated by a letter “c”. The number to the left of the “c” is the channel number and to the right is the channel level. Pressing Up

UpUp

Up or Down

DownDown

Down up to the far end will show the Mode at which the selected Look was

programmed.

Proceed to edit the Mode, the channels numbers and levels of a selected Look.

To edit the Mode of a selected Look:

1. From the Main Menu, press Up

UpUp

Up or Down

DownDown

Down to select Look Store

2. Press Enter

EnterEnter

Enter, then press UUUUpppp or Down

DownDown

Down to select a Look

3. Press Enter

EnterEnter

Enter to access the memory data.

4. Press Up

UpUp

Up or Down

DownDown

Down up to the far end until Mode number is shown

5. Press Ente

EnteEnte

Enterrrr, then press Up

UpUp

Up or Down

DownDown

Down to adjust the Mode number

Inspire User Manual 10 V1.4 May 2014

www.chroma

-

q.com

6. Press Enter

EnterEnter

Enter to navigate back to the channel numbers

7. When editing is complete, press Enter

EnterEnter

Enter for 2 seconds to save

The modified Look will be stored in the selected Look Store number.

To edit the channel numbers and levels of a selected Look:

1. From the Main Menu, press Up

UpUp

Up or Down

DownDown

Down to select Look Store

2. Press Enter

EnterEnter

Enter, then press Up

UpUp

Up or Down

DownDown

Down to select a Look

3. Press Enter

EnterEnter

Enter to access the memory data.

4. Press Up

UpUp

Up or Down

DownDown

Down to select the channel number.

5. To edit the channel level, press Enter

EnterEnter

Enter and Up

UpUp

Up or Down

DownDown

Down to adjust the level (shown as 0-255).

6. Press Enter

EnterEnter

Enter to navigate back to the channel number.

7. When the desired effect is created press Enter

EnterEnter

Enter for 2 seconds to save

The modified Look will be stored in the selected Look Store number.

Technical

In this mode, the frequency setting of the fixture can be changed. The Inspire fixture has four frequency settings available - 1200, 2400, 4800, 9600. This allows for the LED scan rate to be synchronised with the video camera and avoid a flickering effect.

To set the frequency,

1. From the Main Menu, press Up

UpUp

Up or Down

DownDown

Down to select Technical

2. Press Enter

EnterEnter

Enter, then press Up

UpUp

Up or Down

DownDown

Down to select the Frequency

3. Press Enter

EnterEnter

Enter for 2 seconds to save

The display returns to Technical and then the Main Menu.

Reset to Default

To reset the fixture to the factory default settings,

1. From the Main Menu, press Up

UpUp

Up or Down

DownDown

Down to select Reset to Default

2. Press Enter

EnterEnter

Enter, display shows “reset?”

3. Press Enter

EnterEnter

Enter and hold until display shows “resetting” and “done” when complete

The display returns to Reset to Default and then the Main Menu.

All control menu commands are reset to factory defaults:

DMX address 001

Control Mode RGBW

When DMX is Lost HOLD

Look Store 01

Frequency 1200

Inspire User Manual 11 V1.4 May 2014

www.chroma

-

q.com

2.7 DMX Protocol – Inspire

DMX Personality Mode 1-2:

Inspire V2.1

Inspire V2.1Inspire V2.1

Inspire V2.1

Control Mode 1

[7ch]

fxHSI

Control Mode 2

[5ch]

sRGBW

Channel 1 Colour Speed

0-255 Variable speed of colour scrolling. Static at 0 to max at 255.

Intensity Effects 0 Static 1-63 Fade on, fade off. Variable, 63 fastest 64-127 Fade on, snap off. Variable, 127 fastest 128-191 Snap on, fade off. Variable, 191 fastest 192-255 Snap on, snap off (strobe). Variable, 255 fastest.

Channel 2 Colour Range

0 Full spectrum 1-255 Variable limit of spectrum for colour scrolling. Single colour at 1, full spectrum at

255.

Red

Channel 3 Colour Step

0-255 Variable control of smoothness of colour scrolling. Smoothest at 0. Most coarse is at

250. Rate will vary with scrolling speed. 255 will override effects and switch to RGB.

Green

Channel 4 Intensity Effects

0 Static 1-63 Fade on, fade off. Variable, 63 fastest 64-127 Fade on, snap off. Variable, 127 fastest 128-191 Snap on, fade off. Variable, 191 fastest 192-255 Snap on, snap off (strobe). Variable, 255 fastest.

Blue

Channel 5 Hue White Channel 6 Saturation Channel 7 Intensity

Total 7 DMX channels 5 DMX channels

DMX Personality Mode 3-4:

Inspire V2.1

Inspire V2.1Inspire V2.1

Inspire V2.1

Control Mode 3

[3ch]

HSI

Control Mode 4

[4ch]

RGBW

Channel 1 Hue Red Channel 2

Saturation Green

Channel 3

Intensity Blue

Channel 4

White

Total 3 DMX channels 4 DMX channels

Inspire User Manual 12 V1.4 May 2014

www.chroma

-

q.com

DMX Personality Mode 11:

Inspire V2.1

Inspire V2.1Inspire V2.1

Inspire V2.1

Mode 11

Mode 11 Mode 11

Mode 11

[1ch]

[1ch][1ch]

[1ch]

Look Select

Look SelectLook Select

Look Select

Channel 1

Channel levels and the corresponding Look numbers:

Channel Level (%) Look Description

0 OFF

1–2 1 Full Colour Scroll (5 sec)

3–5 2 Full Colour Scroll (10 sec)

6–9 3 Full Colour Scroll (30 sec)

10–11 4 Warm Colour Scroll (5 sec)

12–15 5 Warm Colour Scroll (10 sec)

16–19 6 Warm Colour Scroll (30 sec)

20–22 7 Cold Colour Scroll (5 sec)

23-25 8 Cold Colour Scroll (10 sec)

26–27 9 Color Colour Scroll (30 sec)

29-32 10 Red Full

33–35 11 Pink Full

36-38 12 Orange Full

39-42 13 Light Orange Full

43-45 14 Yellow Full

46-48 15 Light Yellow Full

49-51 16 Green Full

52-54 17 Light Green Full

56-58 18 Cyan Full

59-61 19 Light Cyan Full

62-64 20 Blue Full

65-68 21 Light Blue Full

69-71 22 3200 White

72-74 23 5600 White

75-78 24 Empty

79-81 25 Empty

83-85 26 Empty

86-88 27 Empty

89-91 28 Empty

92-94 29 Empty

95-97 30 Empty

98-100 31 Empty

Inspire User Manual 13 V1.4 May 2014

www.chroma

-

q.com

2.8 Thermal Performance

The internal cooling system of the Inspire fixture is by convection. When the internal temperature exceeds 75ºC, the output

of the fixture is reduced for automatic protection. This happens on rare and extreme conditions when ambient temperature is over 35ºC.

3. Troubleshooting

Troubleshooting is a process of elimination. First, rule out the other field factors (i.e. bad connections, faulty cables and power supplies). For technical support and/or parts, please contact your selling dealer or the offices listed in this manual.

Symptom Possible Cause Solution

Fixture does not respond to DMX control.

•

Set to wrong or different DMX address.

•

Bad cable connecting DMX control and fixture.

•

Bad in/through connection between adjacent fixtures.

•

Check DMX address and Mode settings.

•

Check/replace DMX run from the console.

Low LED output.

•

Internal temperature is over the limit.

•

Check area ventilation.

4. Specification

Inspire User Manual 14 V1.4 May 2014

www.chroma

-

q.com

4.1 Technical Specifications

Product Code CHINHLRGBW32A CHINHLRGBW42A CHINHLRGBW65A

Net Dimensions** (Without Fixings - Width x Height x Depth)

181mm x 404mm x 181mm / 7" x 16” x 7"

Net Weight (Without Fixings) 6 kgs / 13.5 lbs Shipping Dimensions – Width x Height x Depth

501mm x 380mm x 300mm / 20" x 15" x 12"

Shipping Weight 8 kgs / 18 lbs Power & Connections Power Supply Built-in Power Input Rating 100-240V AC 50-60Hz 120VA Power Factor 0.9 Power Consumption 120W @ 230V AC (Maximum Intensity); 7W @ 230V AC (Stand-by) Typical Power & Current Measurements done with all LEDs at maximum intensity. Measurements made at nominal

voltage. Allow for a deviation of +/- 10%. Power connector In/Out PowerCon (Input only) Data Connectors In/Out XLR 5-pin Control Protocol ANSI E1.11 USITT DMX 512-A Cooling System Convection Operating Temperature 0°C to 40°C Construction Anodised aluminium extrusion Colour Black Built-In Hardware Mounting bracket IP Rating IP20 Approvals CISPR 22/EN55022 & CISPR 24/EN55024, ICES-003 Issue 4:2004 / FCC Part 15 Subpart

B:2010, CSA C22.2 No. 166-M1983: R2008, UL 1573:2003 (R2010), UL SUBJECT 8750:

2009, IEC 60598-2-17 Control & Photometric LEDs 18 x Neutral White + 6 x RGB, total 36 LEDS LED Engines 1 LEDs Per Engine 36 Total LEDs 36 Control Modes 7 channels fxHSI, 5 channels sRGBW, 3 channels HSI, 4 channels RGBW, 1 channel Look sel,

Mastr StndAlon, Slave StndAlon Dimming Curve Theatrical Variable Effects Engine Yes Effects Parameters Colour speed, range, step, intensity effects Hot Lumen Output (Combined) 4,390 (N) 4,070 (M) 4,390 (W) Optics Fully Homogenised Beam Angle N @ 32° (approx.) M @ 42° (approx.) W @ 65° (approx.) Beam Distribution Symmetrical direct illumination CCT Adjustable 1,000 – 10,000K Colour Gamut Performance enhanced CRI 90 Lamp Life L70 at 50,000 hours

**

For exact measurements please refer to the line drawings below

Inspire User Manual 15 V1.4 May 2014

www.chroma

-

q.com

4.2 Drawings – Dimensions

5. Maintenance

With care, the Inspire fixture requires little maintenance. However, as the unit is likely to be used in a stage environment we recommend periodical internal inspection and cleaning of any resulting dust and cracked oil residue.

Do not spray liquids on the front or rear panel. If the front enclosure requires cleaning, wipe with a mild detergent on a damp cloth.

Inspire User Manual 16 V1.4 May 2014

www.chroma

-

q.com

6. Ceiling Installation Procedure

The Inspire fixture can be mounted on a ceiling with the Inspire Ceiling Installation Kit. The Inspire Ceiling Installation Kit

consists of the following items: (See drawing below with the reference numbers.)

Ref No

Ref NoRef No

Ref No Name

NameName

Name Description

DescriptionDescription

Description

1 Trim Ring Inspire Black A ring that holds and fastens the fixture in place (facing downwards)

with 4 slots for fixture trim height adjustment

2 Bracket Hook A bracket shaped with 2 hooks and built with 2 x ¼-20” pem nuts.

The 2 hooks are set on the edges of 2 extruded fins of the fixture.

The Trim Ring is fastened on the 2 pem nuts of the Bracket Hook.

3 T-Nut ¼-20” Economy 15S Nuts inserted into the extruded cavity between 2 extruded fins

4 Angle support ceiling mounting 2 angle bars that are mounted onto the ceiling

5 Screw Flanged Button Socket ¼-20 x ¾” Fastening screw

6 Washers

Disclaimer:

•

Installation should be carried out by an experienced professional. The instructions below are provided for

information only.

•

All work should be verified to meet Local and National Building Regulations, and Health and Safety Standards

in particular.

•

Ensure that the specified torque is applied to fasten the Trim Ring and Angle Supports.

•

The Angle Supports of the Inspire fixture must be fastened to the ceiling with the appropriate load capacity.

•

The use of a safety chain or other all arrest cable is strongly recommended as per standard rigging practice.

Inspire User Manual 17 V1.4 May 2014

www.chroma

-

q.com

6.1

Remove the Cap:

•

Position the fixture lens side up. Ensure

that the display screen at the rear/bottom

is resting on a clean scratch-free surface

and the female XLR-5 latch at the rear is

not pressed.

•

Unscrew the 2 x M3 FH screws at the

front to remove the Cap.

6.2 Insert the 2 Bracket Hooks

•

Insert and hook the 1st Bracket Hook to

set onto the edges of 2 straight extruded

fins (not curved).

•

The threaded side of the Bracket Hook

must be adjacent towards the external

side of the enclosure.

•

Insert and hook the 2nd Bracket Hook to

set onto the edges of the 2 straight

extruded fins (not curved) on the opposite

side.

6.3

Attach th

e Angle Supports to the Trim Ring

•

Attach the 1st angle support onto one side

of the trim ring.

•

Insert a flanged button head socket screw

through the hole in the angle support into

a trim ring slot and fasten a nut loosely.

•

Attach the 2nd angle support onto the

opposite side of the trim ring.

•

Insert a flanged button head socket screw

through the hole in the 2nd angle support

into the opposite trim ring slot and fasten a

nut loosely.

Bracket Hook on the opposite side

Bracket Hook

Angle Support

Nut

Flanged button head screw

Trim Ring

Inspire User Manual 18 V1.4 May 2014

www.chroma

-

q.com

6.4

Slide the Trim Ring and Angl

e Support assembly down onto the fixture

•

Align the 2 empty slots of the trim ring to

match the threads of the 2 bracket hooks

on the fixture.

•

Slide the trim ring down onto the fixture:

•

Match the 2 empty trim ring slots to the

bracket hook threads.

•

Match and insert the 2 loosely fastened

screw nuts into the slots between the fins.

6.5

Put the Cap back

•

Put the cap back and fasten with 2 x M3

FH screws (5.5 in-lb torque).

6.6

Fasten the Trim Ring to the 2 Bracket Hooks on the fixture

•

Adjust the trim height then fasten with the

4 flanged button socket screws and

washers onto the 2 Bracket Hooks on both

sides of the fixture.

Note:

Minimum torque for the ¼-20 in. flanged

button socket screw is 48 in-lb.

6.7

Tighten the screws on the

Angle Supports

•

Tighten the loosely fastened flanged

button socket screws on each of the angle

supports.

Note:

Minimum suggested torque for the ¼-20 in.

flanged button socket screw is 48 in-lb.

6.8 Install the fixture onto the ceiling

Slot for Nut

Slot for Bracket Hook

Cap

Screw & washers

Inspire User Manual 19 V1.4 May 2014

www.chroma

-

q.com

•

Turn the fixture with the Trim Ring and

Angle Supports lens side down.

•

Fasten the angle supports onto the

appropriate ceiling infrastructure.

Chroma Inspire User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual