Chroma AutoLED II Quick Start Manual

AutoLED II Quick Start Guide V1.053 AutoLED II Quick Start Guide V1.053 PN: 637-0701

Approvals & Disclaimer

The information contained herein is offered in good faith and is believed to be accurate. However,
because conditions and methods of use of our products are beyond our control, this information should
not be used in substitution for customer's tests to ensure that Chroma-Q products are safe, effective,
and fully satisfactory for the intended end use. Suggestions of use shall not be taken as inducements to
infringe any patent. Chroma-Q sole warranty is that t he product will meet the Chroma-Q sales
specifications in effect at the time of shipment. Your exclusive r emedy for breach of such warranty is
limited to refund of purchase price or replacement of any product shown to be other than as warranted.

Chroma-Q reserves the right to change or make alteration to devices and their functionality without notice
due to on-going research and development.

The Chroma-Q AutoLED II has been designed specifically for the lighting industry. Regular maintenance
should be performed to ensure that the products perform well in the entertainment environment.

If you experience any difficulties with any Chroma-Q products please contact your selling dealer. If your
selling dealer is unable to help please contact [e-mail]. If t he selling dealer is unable to
satisfy your servicing needs, please contact the following for full factory service:

Outside North America: North America:

Tel: [phone] Tel: [phone]
Fax: [phone] Fax: [phone]
[e-mail] [e-mail]

For further information please visit the Chroma-Q website at www.chroma-q.com.

Chroma-Q and AutoLED II are trademarks, for more information on this visit
www.chroma-q.com/trademarks.

The rights and ownership of all trademarks are recognised.

Quick Start Guide

Chroma-Q®

AutoLED II™

For a full product manual please visit www.chroma-q.com

Software Version 1.05

AutoLED II Quick Start Guide V1.053 AutoLED II Quick Start Guide V1.053

1. Overview

The new Chroma-Q®™ AutoLED II™ is a 6,500K CCT, Daylight Moving Yoke LED fixture with 48 cold white high p owered
LEDs. The model is equipped with a built-in power supply and remotely controlled through ANSI E1.11 USITT DMX 512-A
protocol.

2. Safety

Caution

1. This product is for professional use only. It is NOT intended for domestic or

outdoor use.

2. The bright flash of light during power-up & continuous strobe may cause epileptic seizure .

3. This product must be used with safety cable.

3. Cabling

The AutoLED II ut ilises an IEC chassis c onnector for power input. The DMX control data input and through connections from
an external control console are via two XLR 5-pin connectors. The chassis is ground bonded.

4. Mounting

The AutoLED II fixture base is floor mount. T he bottom of the fixture base has provisions to fasten the mounting bracket for
overhead truss mounting applications.
Note: Secure the fixture with a safety bond. Provision for a fixing hold is built into the fixture base.

5. Accessories

Louver: A louver is fastened to the front of the AutoLED II fixture head. The louver can be detached from the fixture head by
removing 2 screws.

Beam Shaper: An optional Beam Shaper attachment can be placed onto the front of the AutoLED II fixture head. The Beam
Shaper attachment is a diffuser film which can be controlled (On/Off) via DMX. There are 2 pins at the rear side of the Beam
Shaping Attachment. The 2 pins match the 2 holes at the front of the AutoLED II fixture head. To attach the Beam Shaper,

1. Remove the louver

2. Match the 2 pins underneath the Beam Shaper attachment to the holes on the LED head

3. Align, set and fasten (with 2 screws) the Beam Shaper attachment onto the LED head with the 2 pins in the holes

4. Set the Diffuser Control on the display screen. (See Control Menu > Setup Menu > Technical)

6. Moving Yoke Pan & Tilt Movement

1 DMX channel is assigned to each movement:

Pan 1 DMX channel

Pan (fine movement)

1 DMX cha

nnel

Tilt 1 DMX channel

Tilt (fine movement) 1 DMX channel

Maximum range of Movement & Direction:

Movement Range Direction

Pan 540° Normal or Reverse

Tilt 270° Normal or Reverse

7. Power Switch

The Power ON

ONON

ON/OFF

OFFOFF

OFF switch is located at the rear of the fixture base. The Touch Screen LCD display at the front of the fixture

base lights up to show the opening screen when the switch is turned to ON

ONON

ON.

8. Control

The control functions of the AutoLED II are a ccessed through the Touch Screen LCD display in front of the fixture. The
features of the Touch Screen LCD display are:

Screen menu title

The fixture name or mode name is displayed on top of the screen.

Control Information DMX address, footprint channels, mode name, values and indicators that appear after the command

buttons are tapped.

Command buttons

Buttons which can be tapped to access control functions and options.

Locked Default sets the screen to switch off & lock if untouched for 30 sec. Tap the screen to activate then

press & hold the lock symbol for 5 sec.

Control Menu

Main Menu: displays the fixture name, control information and the main command buttons:

Control Information:

Address DMX start address

Footprint DMX channels assigned

Diffuser Status: On/Off

Pan Dir Pan direction

Tilt Dir Tilt

direction

Command Buttons:

Chang e Add

Chang e AddChang e Add

Chang e Add

Change DMX start address

Setup Menu

Setup MenuSet up Men u

Setup Menu

Change internal settings

1. Tap a command button to access the control options available.

2. Tap App ly

ApplyApply

Apply to save or Escap e

Escap eEscap e

Escap e to return to Main Menu.

Chang e Add

Chang e AddChang e Add

Chang e Add

Change DMX Addre

ss

Use the numeric buttons t

o change the DMX start address,

Setup Menu

Setup MenuSetu p Menu

Setup Menu

In this menu, internal settings of the fixture can be re

-

configured.

Command Buttons:

Scree n

Scree nSc reen

Scree n

Display rotation, Lock screen

Techn ical

Techn icalTechn ical

Techn ical

DMX Data, Frequency, Upload Engine & Diff

user Control

Dire ction

Dire ctionDire ction

Dire ction

Pan Direction, Tilt Direction

Oper ation

Oper ationOpe ration

Oper ation DMX Lost, Fan Speed, Reset

Scree n

Scree nSc reen

Scree n

In this menu, the display screen can be set and locked.

Rotate Disp

Rotate DispRotate Disp

Rotate Disp

Rotate the display screen by 180 degree

LockS creen

LockS creenLockS creen

LockS creen Enable or disable display screen lock

Techn ical

Techn icalTechn ical

Techn ical

In this menu, the following command options are available:

DMX Da ta

DMX Da taDMX Da ta

DMX Da ta

DMX data can be accessed

Frequ ency

Frequ encyFrequency

Frequ ency The fixture can be set with four frequency options: 1200Hz

1200H z1200H z

1200H z,

2400 Hz

2400 Hz2400 Hz

2400 Hz, 480 0Hz

4800H z4800H z

4800H z, 9600 Hz

9600H z9600H z

9600H z

Uploa d ENG

Uploa d ENGUpload E NG

Uploa d ENG

LED Engine software can be up

loaded to the fixture from an

external source by activating this menu

Diffus CTL

Diffus CTLDiffus CTL

Diffus CTL

Beam Shaper

attachment is

enabled or disabled in the Diffuser

Control command. When Diffuser Control is On, the DMX channel
for Diffuser Control is added and the Footprint will have 6 DMX
channels.

Direc tion

Direc tionDirec tion

Direc tion

In this menu, the direction of the yoke and head Pan & Tilt movement can be set.

Oper ation

Oper ationOpe ration

Oper ation

In this menu, the following command options are available:

DMX Lo st

DMX Lo stDMX Los t

DMX Lo st

Select between

Last d ata

Last d ataL ast data

Last d ata or

No ou tput

No ou tputN o output

No ou tput

Fan Sp ee

Fan Sp eeFan Spee

Fan Sp ee

dddd

Select between

Low

LowLow

Low or

High

High H igh

High

Reset

ResetReset

Reset

Reset to

Factor y Default

Factor y DefaultFactor y Default

Factor y Default

or

User

User U ser

User

saved settings

Factory Default Settings:

DMX Address

– 1 Direction –

Normal

Lock –

Enable DMX Lost

– Last Data

Frequency – 1200Hz Fan Speed – High

Diffus CTL

– Off Reset -

Default

9. Further Information

Please refer to the Chroma-Q Au toLED II manual for more detailed information. A copy of the manual can be found at the
Chroma-Q website – www.chroma-q.com – under Support.