Christie WU7K-M, HD6K-M, HD12K-M, HD10K-M, DS+6K-M User Manual
...
Mirage M Series
USER MANUAL
020-100575-02
Mirage M Series
USER MANUAL
020-100575-02
NOTICES
COPYRIGHT AND TRADEMARKS
© 2010 Christie Digital Systems USA, Inc. All rights reserved.
All brand names and product names are trademarks, registered trademarks or trade names of their respective holders.
REGULATORY
The product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference when the product is operated in a commercial environment. The
product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of the product in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at the user’s own expense.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
이 기기는 업무용 (A 급 ) 으로 전자파적합등록을 한 기기이오니 판매자 또는 사용자는 이점을 주의하시기 바라며 , 가정 외의 지역에서 사용하는 것을
목적으로 합니다 .
GENERAL
Every effort has been made to ensure accuracy, however in some cases changes in the products or availability could occur which may not be
reflected in this document. Christie reserves the right to make changes to specifications at any time without notice. Performance specifications
are typical, but may vary depending on conditions beyond Christie's control such as maintenance of the product in proper working conditions.
Performance specifications are based on information available at the time of printing. Christie makes no warranty of any kind with regard to this
material, including, but not limited to, implied warranties of fitness for a particular purpose. Christie will not be liable for errors contained herein
or for incidental or consequential damages in connection with the performance or use of this material.
The product is designed and manufactured with high-quality materials and components that can be recycled and reused. This symbol
means that electrical and electronic equipment, at their end-of-life, should be disposed of separately from regular waste. Please dispose of the
product appropriately and according to local regulations. In the European Union, there are separate collection systems for used electrical and
electronic products. Please help us to conserve the environment we live in!
Canadian manufacturing facility is ISO 9001 and 14001 certified.
GENERAL WARRANTY STATEMENTS
For complete information about Christie’s limited warranty, please contact your Christie dealer. In addition to the other limitations that may be
specified in Christie’s limited warranty, the warranty does not cover:
a. Damage occurring during shipment, in either direction.
b. Projector lamps (See Christie’s separate lamp program policy).
c. Damage caused by use of a projector lamp beyond the recommended lamp life, or use of a lamp supplied by a supplier other than Christie.
d. Problems caused by combination of the product with non-Christie equipment, such as distribution systems, cameras, video tape recorders,
etc., or use of the product with any non-Christie interface device.
e. Damage caused by misuse, improper power source, accident, fire, flood, lightening, earthquake or other natural disaster.
f. Damage caused by improper installation/alignment, or by product modification, if by other than a Christie authorized repair service
provider.
g. For LCD projectors, the warranty period specified applies only where the LCD projector is in “normal use.” “Normal use” means the LCD
projector is not used more than 8 hours a day, 5 days a week. For any LCD projector where “normal use” is exceeded, warranty coverage
under this warranty terminates after 6000 hours of operation.
h. Failure due to normal wear and tear.
PREVENTATIVE MAINTENANCE
Preventative maintenance is an important part of the continued and proper operation of your product. Please see the Maintenance section for
specific maintenance items as they relate to your product. Failure to perform maintenance as required, and in accordance with the maintenance
schedule specified by Christie, will void the warranty.
Table of Contents
1: Introduction
1.1 Labels and Marking .....................................................................................................................1-1
1.1.1 Typographical Notations......................................................................................................1-2
1.2 Purchase Record and Service Contacts .......................................................................................1-2
1.3 Projector Overview......................................................................................................................1-3
1.3.1 How the Projector Works ....................................................................................................1-3
1.3.2 User Interface Overview......................................................................................................1-3
1.3.3 List of Components..............................................................................................................1-3
1.3.4 Key Features ........................................................................................................................1-4
1.4 Safety Warnings and Guidelines .................................................................................................1-5
1.4.1 General Precautions .............................................................................................................1-5
1.4.2 AC /Power Precautions........................................................................................................1-5
1.4.3 Lamp Precautions ................................................................................................................1-5
2: Installation and Setup
2.1 Projector Quick Setup and Installation........................................................................................2-1
2.2 Detailed Setup and Installation....................................................................................................2-5
2.2.1 About the Projector..............................................................................................................2-5
2.2.2 Projector Position and Mounting .........................................................................................2-8
2.2.3 Mounting..............................................................................................................................2-10
2.2.4 Adjusting Projector Height/Tilt ...........................................................................................2-10
2.2.5 Basic Optical Alignment......................................................................................................2-11
2.2.6 Advanced Optical Alignment ..............................................................................................2-12
2.2.7 Powering Down ...................................................................................................................2-14
2.2.8 Connecting Communications...............................................................................................2-15
2.2.9 Projector Communications ................................................................................................2-20
2.3 Connecting Sources .....................................................................................................................2-21
3: Operation
3.1 Using the Remote Keypad or Built-In Keypad ...........................................................................3-1
3.1.1 Remote Keypad Commands ................................................................................................3-4
3.2 Navigating the Menus..................................................................................................................3-8
3.3 Using Inputs and Channels ..........................................................................................................3-12
3.4 Channel Setup Menu ...................................................................................................................3-14
3.5 Adjusting the Image.....................................................................................................................3-17
3.6 Size and Position Menu ...............................................................................................................3-18
3.7 Image Settings Menu ...................................................................................................................3-21
3.8 Configuration - Adjusting System Parameters and Advanced Controls .....................................3-30
3.9 Lamp Menu..................................................................................................................................3-49
3.10 Secondary Input Switching Menu .............................................................................................3-51
3.11 Status .........................................................................................................................................3-51
3.12 Using Multiple Projectors..........................................................................................................3-51
3.13 Remote Control of the Projector................................................................................................3-55
3.14 Alarm Conditions ......................................................................................................................3-55
3.15 3D ..............................................................................................................................................3-56
Mirage M Series User Manual i
020-100575-02 Rev. 1 (11-2010)
Table of Contents
3.15.1 Requirements .................................................................................................................... 3-56
3.15.2 Active and Passive Stereo 3D Configurations .................................................................. 3-58
3.15.3 Example of 3D Multiple Display Setup............................................................................ 3-61
4: Web User Interface
4.1 Logging On ................................................................................................................................. 4-1
4.2 Navigating the Web User Interface............................................................................................. 4-2
4.2.1 Help Text............................................................................................................................. 4-2
4.3 Basic Operation........................................................................................................................... 4-3
4.3.1 Main Tabbed Page - General .............................................................................................. 4-3
4.3.2 Main Tabbed Page - Status ................................................................................................. 4-3
4.3.3 Main Tabbed Page - Lens ................................................................................................... 4-4
4.3.4 Tools Tabbed Page - Virtual OSD ...................................................................................... 4-4
4.3.5 Admin Tabbed Page - System............................................................................................. 4-6
4.3.6 Admin Tabbed Page- Users ................................................................................................ 4-8
4.3.7 Advanced Tabbed Page - RTE............................................................................................ 4-9
4.3.8 About Tabbed Page............................................................................................................. 4-13
5: Maintenance
5.1 Maintenance of the Cooling System........................................................................................... 5-1
5.1.1 Ventilation........................................................................................................................... 5-1
5.1.2 Optional Filters ................................................................................................................... 5-1
5.2 Maintenance of Optics ................................................................................................................ 5-2
5.2.1 Optical (Excluding Lens) .................................................................................................... 5-2
5.2.2 Cleaning the Lens................................................................................................................ 5-3
5.3 Replacing the Lamps................................................................................................................... 5-3
6: Troubleshooting
6.1 Power .......................................................................................................................................... 6-1
6.1.1 Projector Does Not Power ON............................................................................................ 6-1
6.2 Lamp ........................................................................................................................................... 6-1
6.2.1 Lamp Does Not Ignite......................................................................................................... 6-1
6.2.2 Lamp Suddenly Turns OFF................................................................................................. 6-2
6.2.3 Flicker, Shadows Or Dimness............................................................................................. 6-2
6.3 LCD............................................................................................................................................. 6-2
6.3.1 Blank Screen, No Menu Displaying ................................................................................... 6-2
6.4 Remote Keypad........................................................................................................................... 6-2
6.4.1 Remote Keypad Does Not Seem to Work .......................................................................... 6-2
6.5 OSD............................................................................................................................................. 6-3
6.5.1 The OSD Menu does not display ........................................................................................ 6-3
6.6 Ethernet....................................................................................................................................... 6-3
6.6.1 Trouble Establishing Communication with Projector......................................................... 6-3
6.7 Displays....................................................................................................................................... 6-3
6.7.1 The projector is on but there is no display .......................................................................... 6-3
6.7.2 Severe Motion Artifacts ...................................................................................................... 6-3
ii Mirage M Series User Manual
020-100575-02 Rev. 1 (11-2010)
Table of Contents
6.7.3 Image Appears ‘Squeezed’ or Vertically Stretched into Center of Screen..........................6-4
6.7.4 The Display is Jittery or Unstable........................................................................................6-4
6.7.5 The Display is Faint.............................................................................................................6-4
6.7.6 The Upper Portion of the Display is Waving, Tearing or Jittering......................................6-4
6.7.7 Portions of the Display are Cut Off or Warped to the Opposite edge .................................6-4
6.7.8 Display Appears Compressed (Vertically Stretched) ..........................................................6-4
6.7.9 Data is Cropped from Edges................................................................................................6-4
6.7.10 Display Quality Appears to Drift from Good to Bad, Bad to Good .................................6-4
6.7.11 Display has Suddenly Frozen ............................................................................................6-5
6.7.12 Colors in the Display are Inaccurate..................................................................................6-5
6.7.13 Display is Not Rectangular ................................................................................................6-5
6.7.14 Display is “Noisy” .............................................................................................................6-5
6.8 Web Interface ..............................................................................................................................6-6
6.8.1 After upgrading the projector software, the Web pages do not display correctly ...............6-6
6.8.2 Menu functions are not active..............................................................................................6-6
6.8.3 A backup or Interrogator file cannot be saved.....................................................................6-6
7: Specifications
7.1 Image Performance......................................................................................................................7-1
7.1.1 Pixel Format ........................................................................................................................7-1
7.1.2 Brightness (ANSI Lumens) ................................................................................................7-1
7.1.3 Contrast................................................................................................................................7-1
7.1.4 Luminance Uniformity ........................................................................................................7-2
7.1.5 Color Uniformity .................................................................................................................7-2
7.1.6 Color Primaries ....................................................................................................................7-2
7.1.7 Gamma.................................................................................................................................7-2
7.1.8 Grayscale/Color Resolution.................................................................................................7-2
7.1.9 Color Temperature...............................................................................................................7-2
7.1.10 Convergence ......................................................................................................................7-3
7.1.11 Blemishes...........................................................................................................................7-3
7.1.12 Pixel Defects ......................................................................................................................7-3
7.1.13 Image Artifacts ..................................................................................................................7-3
7.1.14 Picture Centering (with 1.4-1.8:1 HD lens).......................................................................7-4
7.2 Feature Set ...................................................................................................................................7-4
7.2.1 Airflow ................................................................................................................................7-4
7.2.2 Air Filters (Optional) ...........................................................................................................7-4
7.2.3 Dust Sealing.........................................................................................................................7-4
7.2.4 ILS (Intelligent Lens System)..............................................................................................7-4
7.2.5 Projection Lens Compatibility .............................................................................................7-4
7.2.6 Iris .......................................................................................................................................7-5
7.2.7 Automatic Fans ....................................................................................................................7-5
7.2.8 Constant Lamp Output Management...................................................................................7-5
7.2.9 Shutter .................................................................................................................................7-5
7.2.10 Lamps.................................................................................................................................7-6
7.2.11 Status LED.........................................................................................................................7-6
7.2.12 Electronics/SW .................................................................................................................7-6
Mirage M Series User Manual iii
020-100575-02 Rev. 1 (11-2010)
Table of Contents
7.3 Image Processor Performance..................................................................................................... 7-7
7.4 Input (Source Signal) Compatibility .......................................................................................... 7-7
7.4.1 Analog (Only) Input............................................................................................................ 7-7
7.4.2 Twin HDMI Input ............................................................................................................... 7-7
7.4.3 Dual Link DVI Input........................................................................................................... 7-7
7.4.4 Video Decoder Input........................................................................................................... 7-8
7.4.5 Dual SD/HD-SDI ................................................................................................................ 7-8
7.5 Control Signal Compatibility ..................................................................................................... 7-8
7.5.1 Projector Control................................................................................................................. 7-8
7.5.2 Control Receiver ................................................................................................................. 7-8
7.5.3 RS-232 ................................................................................................................................ 7-8
7.5.4 RS-422 ................................................................................................................................ 7-9
7.5.5 Ethernet ............................................................................................................................... 7-9
7.5.6 USB 2.0 Device Port .......................................................................................................... 7-9
7.5.7 GPIO ................................................................................................................................... 7-9
7.5.8 Built-In Keypad and Display .............................................................................................. 7-9
7.5.9 AMX/Crestron Support....................................................................................................... 7-9
7.6 Power Requirements ................................................................................................................... 7-9
7.6.1 Lamp Specification ............................................................................................................. 7-10
7.7 Physical Specifications ............................................................................................................... 7-10
7.7.1 Size...................................................................................................................................... 7-10
7.7.2 Adjustment .......................................................................................................................... 7-11
7.7.3 Weight................................................................................................................................. 7-11
7.7.4 Operating Position............................................................................................................... 7-11
7.8 Reliability and Serviceability...................................................................................................... 7-11
7.8.1 Reliability............................................................................................................................ 7-11
7.8.2 Serviceability ...................................................................................................................... 7-11
7.9 Environment................................................................................................................................ 7-11
7.9.1 Temperature/Humidity/Altitude.......................................................................................... 7-11
7.10 Accessories and Service Components ...................................................................................... 7-12
7.10.1 Service Components ......................................................................................................... 7-12
7.11 Regulatory................................................................................................................................. 7-12
A: Menu Tree
A.1 Mirage M Series Menu Tree ...................................................................................................... A-1
B: GPIO
B.1 GPIO Port................................................................................................................................... B-1
C: DMX / ArtNet
C.1 DMX and Real Time Events ...................................................................................................... C-1
C.1.1 DMX Channel Setup .......................................................................................................... C-2
iv Mirage M Series User Manual
020-100575-02 Rev. 1 (11-2010)
1 Introduction
Every effort has been made to ensure the information in this document is accurate and reliable; however,
due to constant research the information in this document is subject to change without notice.
USERS/OPERATORS: This manual is intended for trained users operating professional high-brightness
projection systems. Such users may also be trained to replace the lamp and air filter, but cannot install the
projector or perform any service functions on the Mirage M Series projector.
SERVICE: Only Christie accredited technicians knowledgeable about all potential hazards associated
with high voltage, ultraviolet exposure and high temperatures generated by the lamp and associated
circuits are authorized to 1) assemble/install the projector and 2) perform service functions inside the
projector.
This manual contains the following sections:
• Section 1 Introduction
• Section 2 Installation and Setup
• Section 3 Operation
• Section 4 Web User Interface
• Section 5 Maintenance
• Section 6 Troubleshooting
• Section 7 Specifications
• Appendix A: Menu Tree
• Appendix B: GPIO
• Appendix C: DMX / ArtNet
DISCLAIMER:
However, due to constant research, the information in this document is subject to change without notice. Christie Digital
Systems assumes no responsibility for omissions or inaccuracies. Updates to this document are published regularly, as
required. Please contact Christie Digital Systems for availability.
Every effort has been made to ensure the information in this document is accurate and reliable.
1.1 Labels and Marking
Observe and follow any warnings and instructions marked on the projector.
Indicates a hazardous situation which, if not avoided, will result in death or serious
injury. This signal word is to be limited to the most extreme situations.
Indicates a hazardous situation which, if not avoided, could result in death or serious
injury.
Indicates a hazardous situation which, if not avoided, could result in minor or moderate
injury. It may also be used without the safety alert symbol as an altermative to
“NOTICE”.
Mirage M Series User Manual 1-1
020-100575-02 Rev. 1 (11-2010)
Section 1: Introduction
1.1.1 Typographical Notations
The following notations are used throughout this manual:
• Keypad commands and PC keystrokes appear in bold, small caps, such as
• References to specific areas within the current document appear italicized and underlined. When viewed
online, the text appears in blue indicating a direct link to that section. For example, Section 2 Installation and
Setup.
• References to other documents appear italicized and blue. When viewed online, the text appears in blue
indicating a direct link to that section. For example, refer to Service Manual.
• References to software menus and available options appear bold, such as Main menu, and available options
appear italicized, such as Preferences.
• User input or messages that appear on screen, in status display units or other control modules appear in
Courier font. For example. “No Signal Present”, Login: christiedigital.
• Error codes, LED status codes appear bold, e.g.
LP, A1, etc.
• Operational states of modules appear capitalized, such as power ON/OFF.
1.2 Purchase Record and Service Contacts
Whether the projector is under warranty or the warranty has expired, Christie’s highly trained and extensive
factory and dealer service network is always available to quickly diagnose and correct projector malfunctions.
Complete service manuals and updates are available for all projectors. Should a problem be encountered with
any part of the projector, contact your dealer. In most cases, servicing is performed on site. If you have
purchased the projector, fill out the information below and keep with your records.
POWER, INPUT, ENTER etc.
Table 1.1
Dealer:
Dealer or Christie Sales/Service Contact Phone Number:
Projector Serial Number*:
Purchase Date:
Installation Date:
* The serial number can be found on the license label located on the back of the projector.
Table 1.2 Ethernet Settings
Default Gateway:
DNS Server:
Projector DLP Address:
Projector Mgmt IP Address:
Subnet Mask:
1-2 Mirage M Series User Manual
020-100575-02 Rev. 1 (11-2010)
1.3 Projector Overview
The Mirage Mirage M Series family of high resolution video/
graphics 3 chip 1080p HD, SXGA+, and WUXGA projectors,
see Table 1.3 Mirage M Series Projectors. These projectors are
based on next generation DLP® technology provided by Texas
Instruments.
1.3.1 How the Projector Works
The projector accepts data/graphics and video input signals for
projection onto front or rear screens. Light is generated by dual
mercury lamps, then modulated by three Digital Micro-mirror
Device (DMD) panels that provide digitized red, green or blue
color information. Light from the “ON” pixels of each panel is
reflected, converged and then projected to the screen through a
single front lens, where all pixels are perfectly superimposed as
a sharp full-color image.
1.3.2 User Interface Overview
Section 1: Introduction
FIGURE 1-1 - MIRAGE M SERIES
The projector can be controlled via a menu system displayed on the image. The menu system can be controlled
by an IR remote, wired remote or through the built-in keypad. The LCD screen and built-in keypad
allow some functions to be controlled without the need of an OSD display, and provide a quickly accessible
interface to view error reporting. The functions on the OSD can also be controlled using the Christie Serial
Protocol, via a serial or Ethernet connection to the projector. The Web interface provides access to the menu
system as a Virtual OSD (On-screen display) and to features that maintain the projector’s software and
settings.
1.3.3 List of Components
Ensure the following components were received with the projector:
Projector with Built-In Keypad (LCD status display)
IR remote keypad (includes two, 1.5V AA batteries and an XLR to mini-stereo cable conversion to wired)
Line cord
Lens Mount Security Screw (M6x10mm long, Qty. 2)
Lens Mount Security Screw (5mm Hex, Qty. 1)
Warranty Card
Web Registration Form
Mirage M Series User Manual 1-3
020-100575-02 Rev. 1 (11-2010)
Section 1: Introduction
1.3.4 Key Features
• Up to 10,500 lumens
• WUXGA Native resolution
• Dual Mercury Lamp illumination with either dual 200W or dual 350W lamps
• Iris contrast aperture providing up to 10,000:1 contrast ratio
• Ultra-compact design and weighs less than 55lbs
• 10-bit image processor electronics with modular design
• Fully sealed optical system
• Active fan control for minimum noise level
• User interchangeable projection lenses with no-tool mounting
• PIP and seamless switching
• LiteLOC for constant brightness maintenance
• Intelligent Lens System (ILS)
• Motorized lens mount for all models
• Auto-setup feature
• Integrated ChristieNET
• Networking ability through RS-232 and RS-422 connectors
• Status LED display on built-in keypad for easy projector status monitoring
• Control with remote keypad, wired remote, or built-in keypad
• Four input slots for Optional Input Modules
Refer to Section 7 Specifications for a complete list of technical specifications.
Table 1.3 Mirage M Series Projectors
Model Name Part Number
MIRAGE DS+6K-M 118-054100-XX
MIRAGE DS+10K-M 118-053109-XX
MIRAGE HD6K-M 118-052108-XX
MIRAGE HD10K-M 118-051107-XX
MIRAGE WU7K-M 118-056102-XX
MIRAGE WU12K-M 118-055101-XX
1-4 Mirage M Series User Manual
020-100575-02 Rev. 1 (11-2010)
1.4 Safety Warnings and Guidelines
1.4.1 General Precautions
FIRE HAZARD. Keep hands, clothes and all combustible material away from the
concentrated light beam of the projector. Position all cables where they cannot
contact hot surfaces or be pulled or tripped over.
All installation and maintenance procedures must be performed by a Christie
accredited service technician.
Section 1: Introduction
Do NOT look into the lens
Projector must be operated in an environment that meets operating specifications, as
listed in Section 7 Specifications.
1.4.2 AC /Power Precautions
Use only the AC power cord supplied. Do not attempt operation if the AC supply and
cord are not within the specified voltage and power range. Refer to the license label
on the back of the projector or Section 7 Specifications for rated voltage and power.
The projector is equipped with a 3-wire plug with a grounding pin. This is a safety
feature. If you are unable to insert the plug into the outlet, contact an electrician to
have the outlet replaced. NEVER defeat the safety purpose of the grounding-type
plug.
Do not allow anything to rest on the power cord. Locate the power cord where
persons walking on it or objects rolling over it cannot damage the cord.
1.4.3 Lamp Precautions
Never attempt to access the lamp while the lamp is ON. After turning the lamp OFF, it
is crucial that you wait at least 10 minutes before handling the lamp. This provides
sufficient time for the lamp cooling fans to properly cool the lamp. For all other
precautions critical for safe removal and replacement of the lamp, refer to 5.3
Replacing the Lamps
Mirage M Series User Manual 1-5
020-100575-02 Rev. 1 (11-2010)
.
2 Installation and Setup
This section explains how to install, connect and optimize the projector for delivery of superior image
quality. Illustrations are graphical representations only and are provided to enhance the understanding of
the written material.
2.1 Projector Quick Setup and Installation
The following instructions are for those preferring a quick setup. Refer to the remaining subsections for
detailed setup instructions.
Always power down the projector and disconnect all power sources before servicing or
cleaning.
Refer to Safety Warnings and Guidelines in Section 5 Maintenance.
STEP 1 - Installing a Projection Lens
The projection lens, shipped separately from the projector, must be installed prior to setting up the projector.
Remove the lens plug from the lens opening in the projector before installing the lens.
Retain the lens plug for projector transportation to protect the projector’s optical
components from dust and debris.
IMPORTANT! The lens seals the projector, preventing contaminants from entering the interior of the
projector. Never operate a projector without a lens.
LENS INSTALLATION
MPORTANT! Remove the rear lens cap from the lens. Keep the front lens cap on the lens to protect it
during installation.
1. Rotate the lens clamp to the OPEN position, see Figure 2-1 Locking Clamp Open.
FIGURE 2-1 LOCKING CLAMP OPEN
Mirage M Series User Manual 2-1
020-100575-02 Rev. 1 (11-2010)
Section 2: Installation and Setup
2. Align the lens interface plate with the lens mount. Align the lens electrical connector with the mating
connector on the lens mount. Fully insert the assembly straight into the lens mount opening without
turning. Press using your hand as shown in Figure 2-2 Lens Placement.
ensure that the lens is not inserted at an angle, as this can cause damage.
NOTE: When installing the lens,
FIGURE 2-2 LENS PLACEMENT
3. Remove the front lens cap.
4. While holding the lens flat against the lens mount, rotate the lens clamp clockwise to lock the lens
assembly in place. See Figure 2-3 & Figure 2-4.
FIGURE 2-3 FIGURE 2-4
5. For added stability such as motion applications, fasten the security screws provided with the lens-mount.
NOTE: There are two types of lens plate models. See Figure 2-5 & Figure 2-6.
2-2 Mirage M Series User Manual
020-100575-02 Rev. 1 (11-2010)
Section 2: Installation and Setup
FIGURE 2-5 FIGURE 2-6
6. Use a 5mm hex driver to fasten the red security screws provided with the lens mount (Figure 2-5), or hand
tighten the lens retaining screws attached to the lens (Figure 2-6). NOTES: 1) Recommended for heaviest
lenses such as 0.73:1 and 1.2:1. 2) The red security screws MUST be installed when hoisting the
projector overhead, or installing the projector in an overhead position.
Use of the lens red security screws or the lens retaining screws is required if the
projector is hoisted or installed in an overhead position.
STEP 2 - Positioning the Projector
2 people are required to safely lift and install the projector.
Place the projector on a sturdy, level surface and position it so that it is perpendicular to the screen at a suitable
distance. The further back the projector is positioned for the screen, the larger the image will be.
To level the projector adjust its 3 feet. With the projector positioned perpendicular to the screen the image will
appear rectangular instead of keystoned.
For more detailed instructions on positioning the projector refer to 2.2.2 Projector Position and Mounting later
in this section.
STEP 3 - Connecting a Source
Located at the back of the projector is the input panel where all source connections are made. Each input is
clearly labeled for easy identification. Depending on the type of option card installed, connect your source
using the appropriate cable(s), as follows:
• Analog Input Card, connect 3-, 4-, or 5-wire RGB source to Red/Pr, Green/Y, Blue/Pb, H/C and V using 3,
4 or 5 BNC connectors as required.
• Dual SD/HD - SDI Input Card, connect SDI (Serial Digital Interface) cable to one of the two inputs, 1-IN
or 2-IN. Both standard-definition (SD) and high-definition (HD) signals are accepted and automatically
recognized on either input.
• Dual Link DVI Input Card, connect a single or dual DVI video signal to the DVI-I connector, an analog
video signal to the DVI-I connector or an analog video signal to the VGA connector. The DVI signal may
contain HDCP (High-Bandwidth Digital Content Protection).
NOTE: The VGA connector does not support
active stereo input, but it can be used for dual input 3D mode.
Mirage M Series User Manual 2-3
020-100575-02 Rev. 1 (11-2010)
Section 2: Installation and Setup
• Twin HDMI Input Card, connect HDMI (High-Definition Multimedia Interface) cable to one of the two
inputs, 1-IN or 2-IN.
• Video Decoder Input Card, depending on the source you can apply the following;
• Composite video source to 1-CVBS, using a BNC Cable
input is selected as CVBS.
• A component signal on Inputs 4(Pr), 5(Y), 6(Pb) using BNC Connectors.
input, YPbPr.
• S-Video to one of the two, 2-SVID or 3-SVID using S-Video cable.
• S-Video using two BNC cables, with Luma (Y) connected to 4 (Sy) and Chroma (C) connected to 6 (Sc).
NOTE: Must be grouped as 1 S-Video + 1 CVBS.
• DMX512 Interface Card, has two 5pin XLR connectors - 1 (input) male and 1 (output) female. If there is
active communications on the DMX512 Interface card the power LED will blink between low intensity and
high intensity.
Refer to Section 2.3 Connecting Sources for more details.
STEP 4 - Connecting the Line Cord
IMPORTANT! Use the line cord provided with the projector, or ensure you are using a line cord, power plug
and socket that meet the appropriate rating standards.
requirements are listed on the license label, located at the back of the projector.
Connect the projector's line cord to the AC receptacle at the AC inlet of the projector, then push the wire clip
over the plug to retain it. This prevents the line cord from inadvertent disconnection. Plug the 3-pronged plug
end into a suitably rated grounded AC receptacle. Switch the projector ON. The switch is located just above the
AC receptacle.
NOTE: Same signal can be used on 4, 5 or 6 when
NOTE: Grouped as a component
NOTE: Voltage and current
Do not attempt operation if the AC supply and cord is not within the specified ratings.
On power down, wait 5-10 minutes for the fans to turn OFF before unplugging the
projector. Always switch off the projector before unplugging the AC line cord.
STEP 5 - Power up
After the AC Power has been switched on, the LCD display above the keypad indicates “Please wait” and the 4
LED status indicators on the top cover window switch on to amber. These indicate that the projector is
changing its state from powered down to standby. The message “Standby Mode” appears in the display when
the projector has completed its initialization and is ready for power up. The 2 lamp status LEDs will go off to
indicate that the lamps are off. The Power status LED will show amber, indicating that the projector is in
standby mode. The shutter LED will display amber, indicating the shutter is closed. Press and hold the power
button on the keypad or remote for 2 seconds, or press twice quickly. The lamps will power on and the fans will
come on.
NOTE: The default settings for the projector are to perform a lens calibration after the insertion of a new lens.
NOTE: See Section 3 Operation for a full description of the status indicators.
If this is the first time the projector has been powered up with the lens, expect a short period (about 15 seconds)
where the lens will move slightly.
STEP 6 - Selecting a Source
Press one of the input keys on the remote or built-in keypad to select and display the image for the source you
connected in Step 3.
2-4 Mirage M Series User Manual
020-100575-02 Rev. 1 (11-2010)
STEP 7- Adjusting Image
Adjust the image settings, such as Brightness, Contrast, Gamma, Focus, Zoom etc. using the direct keys on the
remote or built in keypad.
NOTE: Refer to Section 3 Operation for more details.
2.2 Detailed Setup and Installation
Always power down the projector and disconnect all power sources before servicing
or cleaning.
Section 2: Installation and Setup
Refer to Safety Warnings and Guidelines in
2.2.1 About the Projector
Section 5 Maintenance.
FIGURE 2-7 ABOUT THE PROJECTOR - REAR/SIDE VIEW
Built-in Keypad
The built-in keypad is located on the side of the projector. Use it similarly to the IR remote to control the
projector. An LCD display is located above the keypad for displaying projector status.
AC Receptacle
The AC receptacle is located at the back of the projector. Use this receptacle to plug in an appropriately rated
line cord.
NOTE: The power switch is located above the AC receptacle. Refer to Section 7 Specifications for
details.
Mirage M Series User Manual 2-5
020-100575-02 Rev. 1 (11-2010)
Section 2: Installation and Setup
Adjustable Feet
Located on the underside of the projector are three adjustable feet. Raise or lower these feet when positioning
the projector to ensure it is level on all sides so the displayed image will appear rectangular without any
keystone.
Refer to 2.2.4 Adjusting Projector Height/Tilt for instructions on how to adjust the projector’s feet.
Input Panel
All source connections are made to the input panel located at the back of the projector. Any of the available
optional input cards can be installed in the 4 option card slots. The slots are labelled 1 through 4. All option
cards have LEDs to indicate their status.
Cooling and Air Vents
There are numerous air vents located around the projector. It is important these vents remain unobstructed.
Adequate airflow through the projector will prevent it from overheating.
Kensington Lock Attachment
Located at the rear of the projector to the left of the AC receptacle, is a Kensington lock attachment point. This
provides the ability to secure the projector against possible theft.
Lamp Door
The lamp doors are located at the side of the projector, which provides easy access to the lamp module for
replacement. Refer to Section 5.3 Replacing the Lamps. The lamp doors are fitted with safety interlocks which
switch the lamp off when the door is opened. The lamp doors are provided with clear windows to indicate
when the lamps are on.
FIGURE 2-8 ABOUT THE PROJECTOR - FRONT VIEW
2-6 Mirage M Series User Manual
020-100575-02 Rev. 1 (11-2010)
Section 2: Installation and Setup
Front & Rear IR Sensors
The two IR sensors located on the projector receive transmissions from the IR remote from up to 100 feet
away. It is important to keep the transmission path to these sensors unobstructed for uninterrupted
communications with the projector. The rear IR sensor is located at the back of the projector between the status
LEDs and the front IR sensor is located next to the projector’s front nameplate.
Projection Lenses, Lens Mount and Other Features
The projector includes a motorized lens mount that allows automated lens control and adjustment: vertical and
horizontal offsets, zoom and focus. The lens mount can be fitted with any one of the available optional lenses –
see Section 7 Specifications.
• Zoom and Focus – There are two internal lens motors that allow for quick motorized adjustment of zoom
and focus. Adjust zoom to fit the displayed image on the screen and adjust focus to improve the clarity of the
image.
NOTES: 1) The projection lens is shipped separately from the projector. 2) Use the lens cap when
transporting the lens to avoid scratching and damaging the lens, which could affect your displayed image.
3) Motorized lenses should not be adjusted by hand without first setting them for manual operation,
otherwise the zoom and focus motors may be damaged. (Set in Menu>Configuration>Lens
Settings>Manual Zoom/Focus).
• Lens Offset – The motorized lens mount allows vertical and horizontal offset of the displayed image.
• Shutter – Standard on all models, the shutter allows you to turn the screen absolutely black when in the
“Closed” state.
• Iris Contrast Aperture – Enables adjustment of light output and contrast ratio.
Ambient Lighting
The high brightness of this projector is well suited for locations where ambient lighting might be considered
less than ideal. A typical room with ceiling lights and windows rarely requires special attention. Contrast ratio
in your images will be reduced if stray light directly strikes the screen. For example, when a shaft of light from
a window or floodlight falls on the image. Images may appear washed out and less vibrant. Avoid or eliminate
stray light sources directed at the screen.
Ventilation
The projector vents and louvers provide ventilation, both for intake and exhaust. Never block or cover these
openings. Do not install the projector near a radiator or heat register, or within an enclosure. To ensure
adequate airflow around the projector, allow free air exchange to the projector with a minimum clearance of
25cm (10”) on the left, right and rear sides of the projector from any walls or other obstructions.
NOTE: Do not
obstruct the air exchange to the projector.
Other Considerations
Other considerations and tips to improve your installation:
• Keep the ambient temperature constant and below 40°C (104F). Keep the projector away from heating and/
or air conditioning vents. Changes in temperature may cause drifts in the projector circuitry, which may
affect performance.
• Keep the projector away from devices that radiate electromagnetic energy, such as motors and transformers,
slide projectors, speakers, power amplifiers, elevators, etc.
Mirage M Series User Manual 2-7
020-100575-02 Rev. 1 (11-2010)
Section 2: Installation and Setup
• Use a screen size appropriate for the venue but not larger than required. Installing a large screen in a small
room is similar to watching television at a close range; too large a screen can overpower a room and interfere
with the overall effect. As a rule, be no closer than 1.5 times the width of the screen.
2.2.2 Projector Position and Mounting
Throw Distance
Throw distance is the distance measured from your projector’s front feet to the screen. This calculation
determines if there is enough room to install your projector with a desired screen size and if the image will be
of the right size for your screen.
To estimate the throw distance take the horizontal width of the screen and multiply it by the lens throw ratio.
The result determines approximately the distance the projector should be positioned from the screen to project
a focused image large enough to fill the screen. For example, using a 0.73:1 lens, throw distance would roughly
be 0.73 x screen width.
IMPORTANT! Use the lens and screen size to calculate the precise throw distance using the tables provided
in the Dealer Section of the Christie Website, PN 020-100221-XX. Due to lens manufacturing
tolerances for lens focal length, actual throw distance can vary
same nominal throw ratio.
±5% between lenses with the
FIGURE 2-9 THROW DISTANCE
Vertical and horizontal position
The correct vertical and horizontal position of the projector in relation to the screen depends on the lens type
and the screen size. Ideally, the projector should be positioned perpendicular to the screen. This way, the image
will appear rectangular instead of keystoned (trapezoidal).
The vertical position of the image can be offset (that is moved above or below the optical axis) by adjusting the
motorized lens mount. The amount of vertical offset available depends on the type of lens installed in the
projector and can be limited if horizontal offset has been applied. Vertical offset can be expressed as the
percent of half the image height or the number of pixels of shift from lens center. Refer to Table 2.1 for the
vertical offset of each type of lens.
2-8 Mirage M Series User Manual
020-100575-02 Rev. 1 (11-2010)
Table 2.1 WUXGA Vertical Offset Ranges
WUXGA Lens Description Lens Part Number Minimum Offset
Lens ILS 0.73:1SX+/0.67:1HD 118-100110-XX ±22% ±132 pixels
Lens ILS 1.25-1.6SX+/1.16-1.49HD 118-100111-XX ±82% ±492 pixels
ALL OTHER LENSES ±112% ±672 pixels
Section 2: Installation and Setup
Above or Below
Lens Center
NOTES: 1)
Offsets are subject to ±7% centering tolerance. 2)% Offset = # of pixels of offset/half vertical panel
resolution x 100.
The horizontal position of the image can also be offset; that is moved to the left or right of optical center, by
adjusting the motorized lens mount. The amount of horizontal offset available depends on the lens installed
and if the image has already been vertically offset. Horizontal offset can be expressed as the percent of half the
image width or the number of pixels of shift to one side of lens center. Refer to Table 2.2 for the horizontal
offset of each lens type.
Table 2.2 WUXGA Horizontal Offset Ranges
WUXGA Lens Description Lens Part Number Minimum Offset
Above or Below
Lens Center
Lens ILS 0.73SX+/0.67HD 118-100110-XX ±6% ±58 pixels
Lens ILS 1.25-1.6SX+/1.16-1.49HD 118-100111-XX ±38% ±365 pixels
ALL OTHER LENSES ±54% ±518 pixels
NOTES: 1) Offsets are subject to ±7% centering tolerance. 2)% Offset = # of pixels of offset/half horizontal
panel resolution x 100.
Mirage M Series User Manual 2-9
020-100575-02 Rev. 1 (11-2010)
Section 2: Installation and Setup
2.2.3 Mounting
There are several methods for mounting the projector. In typical front and rear screen installations the projector
can be mounted to a secure and level surface, such as a table or cart. Carts are useful when the projector has to
be moved often. Lock the wheels on a cart, when it is in position, to prevent accidental movement during a
presentation.
Ceiling Mount
The projector can be inverted and suspended from the ceiling using a specially designed ceiling mount fixture
118-100108-XX. This mounting is recommended for those that want the projector out of plain view or have
limited amount of space for the projector. For more information, contact your dealer.
Only use Christie approved mounts designed for your projector. Refer to the
installation instructions and safety guidelines provided with the mount.
Special Mounting
The projector can also be rotated (front-to-back) up to 360 degrees and fixed in a rotated position without
affecting performance. However, the side-to-side tilt limit of the projector must not exceed +/-15 degrees, to
ensure optimal performance of the projector.
2.2.4 Adjusting Projector Height/Tilt
Adjusting Height
You can modify the height of the projector to remedy a slightly uneven mounting surface by adjusting the three
feet threaded into the bottom chassis. Turn each foot clock-wise or counter-clockwise until the projector is
level on all sides.
The front feet are adjusted by turning the collar, see Figure 2-10 Front Foot. The front feet do not rotate when
adjusted. The rear foot is adjusted by turning the entire foot, see Figure 2-11 Rear Foot.
FIGURE 2-10 FRONT FOOT FIGURE 2-11 REAR FOOT
2-10 Mirage M Series User Manual
020-100575-02 Rev. 1 (11-2010)
Adjusting Tilt
Section 2: Installation and Setup
1. Before adjusting tilt, ensure the projector is centered.
screen tilt, or measure this incline with a protractor at the screen.
2. Then tilt the projector to closely match the screen tilt angle by extending or retracting the projector’s 3
adjustable feet.
NOTE: 1) For an ideal installation, the lens surface should be centered and parallel to the screen - this
orientation helps to ensure optimized lens performance with minimal offset. Choose a sturdy mounting surface
that allows for this. If this position is not possible (such as when the projector is significantly higher than the
center of the screen), it is better to rely on offset rather than extra tilt.
2.2.5 Basic Optical Alignment
Only perform image alignment once the projector is fully assembled and powered up in its final location. Basic
image alignment ensures the image reflected from the DMDs is parallel to and well-centered with the lens and
screen. This initial optical alignment is the foundation for optimizing images on the screen and must be
completed before final boresight adjustments. Before beginning ensure the projector is properly positioned
relative to the screen.
Basic Optical Alignment Procedure
1. Display a test pattern: Appropriate for analyzing image focus and geometry, such as the “framing” test
pattern showing the cross-hair centered across the image. Press the T
the built-in keypad and press the soft key that displays Test on the LCD display.
NOTE: Check with site personnel for the degree of
EST key on the remote keypad or use
2. Course focus: Do a quick preliminary focus and (if available) zoom adjustment with the primary lens. Do
not worry about consistency across the image at this point, just center focus. It is good practice to have
zoom adjustment color and focus adjustment color in the center of its range.
3. Center the image in the lens: Holding a piece of paper at the lens surface, adjust offsets as necessary until
the image is centered within the lens perimeter. A full white field works best for this.
4. If necessary, center the image on the screen: If the projector is mounted off center to the screen axis,
then offset the lens as much as required. Aim the projector over slightly towards the center of the screen,
but use caution when doing so, as too much tilt will cause excessive keystone distortion. Lens offset will
not.
5. Re-check side-to-side leveling: With the framing pattern on screen, double-check projector leveling so
the top edge of the image is parallel to the top edge of the screen.
6. Throw Distance: Ensure the projector is positioned in the throw distance range for the particular lens.
Mirage M Series User Manual 2-11
020-100575-02 Rev. 1 (11-2010)
Section 2: Installation and Setup
2.2.6 Advanced Optical Alignment
Boresight Alignment Procedure
1. Display the Boresight Test Pattern by pressing the T
keypad and press the soft key that displays Test on the LCD display, then U
EST key on the remote keypad or use the built-in
P ARROW KEY to cycle to
Boresight, then Enter, see Figure 2-12 Boresight Pattern.
FIGURE 2-12 BORESIGHT PATTERN
2. Focus the image on cross-hair pattern I. Evaluate the focus on cross-hair image II and III. If all 3 images
are in focus, no further action is required. If boresight is required see step 3.
3. If boresight is required, refer to Figure 2-13 Cross-Hair Pattern to understand how the adjustment screws
on the lens mount affect the corresponding cross-hairs on the test pattern.
NOTE: The capscrew, (Figure 2-
14) may be under a plastic cap, remove and retain before adjusting.
4. Use a 5mm Allen™ key to loosen the 3 locking setscrews on the lens mount, see Figure 2-14 Screw
Locations, below. NOTE: The setscrews must be backed out several turns, so that they do not contact the
inner lens mount plate.
2-12 Mirage M Series User Manual
020-100575-02 Rev. 1 (11-2010)
Section 2: Installation and Setup
FIGURE 2-13 CROSS-HAIR PATTERN FIGURE 2-14 SCREW LOCATIONS
5. Fine tune the focus of cross-hair pattern I by adjusting the appropriate capscrew, see Figure 2-14 Screw
Locations. Adjust until the cross-hair image is in focus with minimal flare.
6. Adjust cross-hair pattern II, by adjusting the appropriate capscrew, see Figure 2-14 Screw Locations.
Adjust until the cross-hair image is in focus with minimal flare.
7. Adjust cross-hair pattern III, by adjusting the appropriate capscrew, see Figure 2-14 Screw Locations.
Adjust until the cross-hair image is in focus with minimal flare.
8. Repeat step 5, 6, and 7 as required until all 3 cross-hair patterns are in equal sharp focus. If the boresight is
acceptable, see step 11. If the boresight does not appear to be converging to an acceptable level of image
quality or if the lens will not focus over the correct range of throw distances, then the boresight requires
coarse adjustment, see step 9.
9. The original factory boresight can be recovered approximately by positioning the 3 setscrews, see Figure
2-14 Screw Locations. Position the setscrews flush with the front face of the lens mount plate and in
contact with the inner lens mount plate, see below Figure 2-15 Position Setscrew Flush. This may require
adjusting both setscrews and capscrews.
10. If further action is required. Repeat #2.
11. Lock the setscrews, and re-check the boresight quality. Tighten the setscrew enough to ensure they will not
shift.
Mirage M Series User Manual 2-13
020-100575-02 Rev. 1 (11-2010)
Section 2: Installation and Setup
2.2.7 Powering Down
The projector can be powered down by using one of
the following methods:
FIGURE 2-15 POSITION SETSCREW FLUSH
Remote Keypad/Built-In Keypad
• Press and hold P
OWER
OR
• Press P
OWER twice
OR
• Press P
DOWN key.
second key is not pressed immediately, a
OWER once, then immediately press the
NOTE: For Step 2 and 3, if the
FIGURE 2-16 POWERING DOWN/WEB USER INTERFACE
confirmation window will appear. The second key
press must be pressed within 1 second of the window appearing.
NOTE: After powering down, the Status LEDs cycle and the LCD displays the message “Cooling Down”, until
cool down is complete.
Web User Interface (UI)
1. From the Main Tab, Select Power>OFF.
NOTE: A window will display for confirmation on powering
down, see Figure 2-16.
2. Select Yes.
2-14 Mirage M Series User Manual
020-100575-02 Rev. 1 (11-2010)
Section 2: Installation and Setup
2.2.8 Connecting Communications
Remote Keypads
To control the projector, direct the projector’s IR remote towards the display screen or the projector’s IR sensors.
Alternatively, connect a wired (tethered) version of the remote to the XLR connector labeled as
projector’s input panel.
NOTE: The response to a wired keypad must also be enabled in the Communications menu—
see Section 4 Web User Interface for more information.
As an alternative to the projector’s keypad or remote, you may wish to communicate with the projector using a PC or
other controller. Such a device sends commands and receives feedback via serial links (RS-232 and RS-422RS-422), or
Ethernet communications to the projector, refer to the Serial Command document provided in the Dealer Section of the
Christie Website, PN 020-100224-XX.
1.) Serial Port Connections
RS-232 and RS-422, serial ports available on the projector: You can connect a device with a serial interface, such as a
computer to either of these connectors (not both) and control the projector remotely by entering specific serial
communication commands, see Section 3 Operation,COMMUNICATIONS - Submenu and the Serial Command
document provided in the Dealer Section of the Christie Website, PN 020-100224-XX.
WIRED KEYPAD on the
2.) Connecting RS-232
Two nine-pin D-sub connectors, labeled RS-232 IN and RS-232 OUT on the input panel, are dedicated to
serial communication, see Figure 2-17 Connecting RS-232. Using the appropriate serial communication
cables, connect the controlling source, such as a personal computer to the RS-232 IN connector. Set the
projector baud rate to match that of the computer. See Section 3 Operation for details on changing the
projector’s baud rate.
FIGURE 2-17 CONNECTING RS-232
3.) Connecting RS-422
To control the projector with a computer or other controlling device with RS-422 capability, connect a RS-422
serial communication cable between the controlling device and the RS-422 port on the projector, see Figure 2-
18 Connecting RS-422. RS-422 is better suited than RS-232 for serial communication over distances greater
than 50 feet.
Use the RS-422 port only if your device had RS-422 capability - always consult the
literature provided with your equipment before connecting
Mirage M Series User Manual 2-15
020-100575-02 Rev. 1 (11-2010)
Section 2: Installation and Setup
Ethernet Communications
Refer to Section 3 Operation for further information about setting up and using a projector connected via
Ethernet, and the Serial Command document provided in the Dealer Section of the Christie Website, PN 020-
100224-XX.
FIGURE 2-18 CONNECTING RS-422
Connecting Multiple Projectors
RS-232 NETWORK: To connect multiple projectors in a network with serial communication:
1. Connect the controlling source to the RS-232 IN connector of the first projector in the network.
2. Using another serial communication cable, connect one end to the RS-232 OUT connector and the other
end to the RS-232 IN connector of the next projector.
3. Continue this pattern of connection with all projectors in the network.
NOTE: The last projector in the
network will only have a connection to the RS-232 IN connector, see Figure 2-19 RS-232 Network.
FIGURE 2-19 RS-232 NETWORK
2-16 Mirage M Series User Manual
020-100575-02 Rev. 1 (11-2010)
Loading...