Christie One Mount Data Sheet

Installing a Christie One Mount/Christie One Mount Plus

This document provides instructions for installing the Christie One Mount or Christie One Mount Plus
and optional accessories to mount Christie projectors to a ceiling or truss.

Safety and warning guidelines

Read all safety and warning guidelines before installing the Christie One Mount/Christie One Mount
Plus.

Warning! If not avoided, the following could result in death or serious injury.

• SHOCK HAZARD! Disconnect the product from AC before installing, moving, servicing, cleaning,
removing components, or opening any enclosure.

• A minimum of two people or appropriately rated lift equipment is required to safely lift, install,
or move the product.

• FIRE HAZARD! Do not install near any devices that produce heat such as amplifiers, radiators,
heat registers, or stoves.

• Do not exceed the maximum load capacity of the product.

• Do not install on a structure susceptible to vibration, movement, or change due to impact.

Required tools

The following tools are required to install a Christie One Mount or Christie One Mount Plus.

• 3 mm hex key

• 5 mm hex key

Required components

Ensure the necessary components are available before installing a Christie One Mount or Christie One
Mount Plus.

• Christie One Mount (P/N: 108-506102-XX)

• Christie One Mount Plus (P/N: 140-117100-03)

• Christie One Mount extender rod (P/N: 121-125109-XX)

Installing a Christie One Mount Instruction Sheet 1
020-102437-02 Rev. 1 (04-2019)
Copyright © 2019 Christie Digital Systems USA, Inc. All rights reserved.

Installing a Christie One Mount/Christie One Mount Plus

• Christie One Mount Rigging kit (P/N: 121-126100-XX)

Prerequisites

Before installing Christie One Mount or Christie One Mount Plus, ensure the following is met for the
mount and the supporting structure.

• The maximum loaded a Christie One Mount can support is 24 kg (53 lbs).

• The maximum load a Christie One Mount Plus can support is 45 kg (99 lbs).

• Mount the ceiling plate to a structure capable of handling the combined maximum weight of
the projector with installed accessories and the mount.

• The installation of the ceiling mount and supporting structure must meet local building codes.

• Attach the ceiling plate to the supporting structure using all four holes (mounting screws and
bolts are not included with the mount).

• If mounting to ceiling studs, ensure that the mounting screws are anchored into the center of
the ceiling studs. Christie recommends using an edge-to-edge stud finder.

• Be aware of the mounting environment. If drilling and/or cutting into the mounting surface,
always make sure no electrical wires are in the wall.

• To prevent image vibration, Christie recommends not installing the fog filters on HS Series
projectors mounted with Christie One Mount Plus.

Installing a Christie One Mount/Christie One
Mount Plus

Follow these instructions to install a Christie One Mount or Christie One Mount Plus.

1. To determine the correct mount to use with your projector, refer to the Accessories section of
the Christie website (https://www.christiedigital.com/en-us/products/accessories), select
Ceiling Mounts > Christie One Mount or Christie One Mount Plus.

2. Position and securely fasten the ceiling plate to the ceiling.

3. Insert the calibration device into the ceiling plate and secure with the two setscrews.

Installing a Christie One Mount Instruction Sheet 2
020-102437-02 Rev. 1 (04-2019)
Copyright © 2019 Christie Digital Systems USA, Inc. All rights reserved.

Installing a Christie One Mount/Christie One Mount Plus

4. Position the projector adapter plate with adjustable arms on the bottom side of the projector.

5. Secure the adjustable arm plate to the projector by positioning the screws of the plate with the
designated holes on the bottom of the projector.

When mounting projectors with the Christie One Mount Plus, select the bolt size appropriate
for your projector and tighten to the specified torque.

• M6-1.0: length = 50 mm, torque = 16 Nm, with the 3 mm washer and rubber bushings

• M8-1.25: length = 55 mm, torque = 38 Nm, without washer

When mounting projectors with the Christie One Mount, select the bolt size appropriate for
your projector and tighten to the specified torque.

• M4-0.7: length = 35 mm, torque = 3.5 Nm

• M6-1.0: length = 35 mm, torque = 16 Nm

6. Use the four brass leveling standoffs to attach and level the adapter plate on the projector.

Projector standoffs are adjustable spacers which can be used to level the arms of the Christie
One Mount. The projector standoffs also ensure screws are centered when the projector is
attached to the mount.

Installing a Christie One Mount Instruction Sheet 3
020-102437-02 Rev. 1 (04-2019)
Copyright © 2019 Christie Digital Systems USA, Inc. All rights reserved.