How it Works
Christie
Loading...
DWU1052
User Manual
45 pgs12.82 Mb0
User Manual
114 pgs18.63 Mb0
User Manual
197 pgs57.29 Mb0
User Manual
158 pgs58.68 Mb0
User Manual
404 pgs43.55 Mb0
User Manual
127 pgs27.02 Mb0
User Manual
33 pgs12.58 Mb0

Christie DWU1052, DHD1052 User Manual

Technical User Manual
020-000857-01
Q Series
DWU1052/DHD1052
Projector
DWU1052/DHD1052
User's Manual (detailed) Operating Guide – Technical
Supported signals for COMPUTER IN
Resolution (H x V) Signal mode H. frequency
720 x 400 TEXT 37.9 85 VESA 640 x 480 VGA (60Hz) 31.5 59.9 VESA
VGA (72Hz) 37.9 72.8 VESA VGA (75Hz) 37.5 75 VESA VGA (85Hz) 43.3 85 VESA
800 x 600 SVGA (56Hz) 35.2 56.3 VESA
SVGA (60Hz) 37.9 60.3 VESA SVGA (72Hz) 48.1 72.2 VESA SVGA (75Hz) 46.9 75 VESA SVGA (85Hz) 53.7 85.1 VESA
832 x 624 Mac 16” mode 49.7 74.5 -
1024 x 768 XGA (60Hz) 48.4 60 VESA
XGA (70Hz) 56.5 70.1 VESA XGA (75Hz) 60 75 VESA
XGA (85Hz) 68.7 85 VESA 1152 x 864 1152 x 864 (75Hz) 67.5 75 VESA 1280 x 768 W-XGA (60Hz) 47.7 60 VESA 1280 x 800 1280 x 800 (60Hz) 49.7 60 VESA
1280 x 1024 SXGA (60Hz) 64 60 VESA
SXGA (75Hz) 80 75 VESA
SXGA (85Hz) 91.1 85 VESA
*1 1366 x 768 WXGA (60Hz) 47.7 59.8 VESA
1440 x 900 WXGA+ (60Hz) 55.9 59.9 VESA 1600 x 900 WXGA++ (60Hz) 60 60 VESA
1680 x 1050 WSXGA+ (60Hz) 65.3 60 VESA
1600 x 1200 UXGA (60Hz) 75 60 VESA 1920 x 1080 Full HD (60Hz) 67.5 60 VESA
*2 1920 x 1200 W-UXGA (60Hz)
Reduced Blanking
*1) Only for DHD1052 *2) Only for DWU1052
74 60 VESA
(kHz)
V. frequency
(Hz)
Rating
(continued on next page)
DWU1052/DHD1052 User's Manual - Technical
1
020-000857-01 Rev. 1 (12-2015)
Supported signals
Supported signals for HDMI / HDBaseT
Resolution (H x V) Signal mode H. frequency
(kHz)
V. frequency
(Hz)
720 x 400 TEXT 37.9 85 VESA 640 x 480 VGA (60Hz) 31.5 59.9 VESA
VGA (72Hz) 37.9 72.8 VESA
VGA (75Hz) 37.5 75 VESA
VGA (85Hz) 43.3 85 VESA 800 x 600 SVGA (56Hz) 35.2 56.3 VESA
SVGA (60Hz) 37.9 60.3 VESA
SVGA (72Hz) 48.1 72.2 VESA
SVGA (75Hz) 46.9 75 VESA
SVGA (85Hz) 53.7 85.1 VESA 832 x 624 Mac 16” mode 49.7 74.5
1024 x 768 XGA (60Hz) 48.4 60 VESA
XGA (70Hz) 56.5 70.1 VESA
XGA (75Hz) 60 75 VESA
XGA (85Hz) 68.7 85 VESA
1152 x 864 1152 x 864 (75Hz) 67.5 75 VESA 1280 x 768 W-XGA (60Hz) 47.7 60 VESA 1280 x 800 1280 x 800 (60Hz) 49.7 60 VESA
1280 x 1024 SXGA (60Hz) 64 60 VESA
SXGA (75Hz) 80 75 VESA
SXGA (85Hz) 91.1 85 VESA
1366 x 768 WXGA (60Hz) 47.7 59.8 VESA 1440 x 900 WXGA+ (60Hz) 55.9 59.9 VESA
1600 x 900 WXGA++ (60Hz) 60 60 VESA 1400 x 1050 SXGA+ (60Hz) 65.2 60 VESA 1680 x 1050 WSXGA+ (60Hz) 65.3 60 VESA 1600 x 1200 UXGA (60Hz) 75 60 VESA
*1 1920 x 1200 W-UXGA (60Hz)
74 60 VESA
Reduced Blanking
*1) Only for DWU1052
Rating
-
(continued on next page)
DWU1052/DHD1052 User's Manual - Technical
2
020-000857-01 Rev. 1 (12-2015)
Supported signals
Resolution (H x V) Signal mode H. frequency
(kHz)
V. frequency
(Hz)
Rating
720(1440) x 480i 480i 15.7 60 CEA 720(1440) x 576i 576i 15.6 50 CEA
720 x 480p 480p 31.5 60 CEA
720 x 576p 576p 31.3 50 CEA 1280 x 720p 720p (50Hz) 37.5 50 CEA
720p (60Hz) 45 60 CEA
1920 x 1080i 1080i (50Hz) 28.1 50 CEA
1080i (60Hz) 33.8 60 CEA
1920 x 1080p 1080p (50Hz) 56.3 50 CEA
1080p (60Hz) 67.5 60 CEA
(continued on next page)
DWU1052/DHD1052 User's Manual - Technical
3
020-000857-01 Rev. 1 (12-2015)
Supported signals
Supported signals for DVI-D
Resolution (H x V) Signal mode H. frequency
(kHz)
V. frequency
(Hz)
720 x 400 TEXT 37.9 85 VESA 640 x 480 VGA (60Hz) 31.5 59.9 VESA
VGA (72Hz) 37.9 72.8 VESA VGA (75Hz) 37.5 75 VESA VGA (85Hz) 43.3 85 VESA
800 x 600 SVGA (56Hz) 35.2 56.3 VESA
SVGA (60Hz) 37.9 60.3 VESA SVGA (72Hz) 48.1 72.2 VESA SVGA (75Hz) 46.9 75 VESA SVGA (85Hz) 53.7 85.1 VESA
832 x 624 Mac 16” mode 49.7 74.5
1024 x 768 XGA (60Hz) 48.4 60 VESA
XGA (70Hz) 56.5 70.1 VESA XGA (75Hz) 60 75 VESA
XGA (85Hz) 68.7 85 VESA 1152 x 864 1152 x 864 (75Hz) 67.5 75 VESA 1280 x 768 W-XGA (60Hz) 47.7 60 VESA 1280 x 800 1280 x 800 (60Hz) 49.7 60 VESA
1280 x 1024 SXGA (60Hz) 64 60 VESA
SXGA (75Hz) 80 75 VESA
SXGA (85Hz) 91.1 85 VESA 1366 x 768 WXGA (60Hz) 47.7 59.8 VESA 1440 x 900 WXGA+ (60Hz) 55.9 59.9 VESA 1600 x 900 WXGA++ (60Hz) 60 60 VESA
1400 x 1050 SXGA+ (60Hz) 65.2 60 VESA 1680 x 1050 WSXGA+ (60Hz) 65.3 60 VESA 1600 x 1200 UXGA (60Hz) 75 60 VESA
*1 1920 x 1200 W-UXGA (60Hz)
74 60 VESA
Reduced Blanking
*1) Only for DWU1052
Rating
-
(continued on next page)
DWU1052/DHD1052 User's Manual - Technical
4
020-000857-01 Rev. 1 (12-2015)
Supported signals
Resolution (H x V) Signal mode H. frequency
(kHz)
V. frequency
(Hz)
Rating
720(1440) x 480i 480i 15.7 60 CEA 720(1440) x 576i 576i 15.6 50 CEA
720 x 480p 480p 31.5 60 CEA 720 x 576p 576p 31.3 50 CEA
1280 x 720p 720p (50Hz) 37.5 50 CEA
720p (60Hz) 45 60 CEA
1920 x 1080i 1080i (50Hz) 28.1 50 CEA
1080i (60Hz) 33.8 60 CEA
1920 x 1080p 1080p (50Hz) 56.3 50 CEA
1080p (60Hz) 67.5 60 CEA
(continued on next page)
DWU1052/DHD1052 User's Manual - Technical
5
020-000857-01 Rev. 1 (12-2015)
Supported signals
Supported signals for SDI/DIGITAL1
Resolution (H x V) Signal mode H. frequency
720 x 480i 480i 15.7 60 720 x 576i 576i 15.6 50
1280 x 720p 720p (50Hz) 37.5 50
720p (60Hz) 45 60
1920 x 1080i 1080i (50Hz) 28.1 50
1080i (60Hz) 33.8 60
1920 x 1080sf 1080i (25Hz) 28.1 50
1080i (30Hz) 33.8 60
1920 x 1080p 1080p (50Hz) 56.3 50
1080p (60Hz) 67.5 60
Only support 3G-SDI Level-A signal.
NOTE
• Be sure to check jack type, signal level, timing and resolution before connecting
(kHz)
V. frequency
(Hz)
Rating
SMPTE SMPTE SMPTE SMPTE SMPTE SMPTE SMPTE SMPTE SMPTE SMPTE
this projector to a PC.
• Some PCs may have multiple display screen modes. Use of some of these modes is not possible with this projector.
• Depending on the input signal, full-size display may not be possible in some cases. Refer to the number of display pixels above.
• The signal is converted to the projector’s panel resolution before being displayed. The best display performance is achieved if the resolutions of the input signal and projector panel are
identical.
• Automatic adjustment may not function correctly with some input signals.
• The image may not be displayed correctly when the input sync signal is a composite sync or a
sync on G.
•
The illustrations in this manual are for illustrative purposes. They may differ slightly from
your projector.
DWU1052/DHD1052 User's Manual - Technical
6
020-000857-01 Rev. 1 (12-2015)
Connection to the ports
① ⑤④③②
⑥ ⑩⑨⑧⑦
⑪ ⑮⑭⑬⑫
①⑤ ④ ③ ②
⑥⑩ ⑨ ⑧ ⑦
⑪⑮ ⑭ ⑬ ⑫
Connection to the ports
Connection to the ports
NOTICE
►Use the cables with straight plugs, not L-shaped ones, as the
input ports of the projector are recessed. ►Only the signal that is input from the COMPUTER IN can be output from the
MONITOR OUT port.
A
B
A
COMPUTER IN, BMONITOR OUT
D-sub 15pin mini shrink jack
<Computer signal>
• Video signal: RGB separate, Analog, 0.7Vp-p, 75Ω terminated (positive)
• H/V. sync. signal: TTL level (positive/negative)
• Composite sync. signal: TTL level
<Component video signal>
• Video signal: Y with composite sync, Analog, 1.0±0.1Vp-p, 75Ω terminated Cb/Pb, Analog, 0.7±0.1Vp-p, 75Ω terminated Cr/Pr, Analog, 0.7±0.1Vp-p 75Ω terminated
• System: 480i@60, 480p@60, 576i@50, 720p@50/60, 1080i@50/60, 1080p@50/60
Pin Signal Pin Signal
1 Video Red, Cr/Pr 9 (No connection) 2 Video Green, Y 10 Ground 3 Video Blue, Cb/Pb 11 (No connection) 4 (No connection) 12
A
: SDA (DDC data)
5 Ground 13 H. sync / Composite sync. 6 Ground Red, Ground Cr/Pr 14 V. sync.
A
7 Ground Green, Ground Y
15
: SCL (DDC clock)
8 Ground Blue, Ground Cb/Pb
B
: (No connection)
B
: (No connection)
DWU1052/DHD1052 User's Manual - Technical
7
020-000857-01 Rev. 1 (12-2015)
Connection to the ports
①⑤④③
②⑥⑩⑨⑧
⑦⑪⑮⑭⑬
⑫
⑲⑱⑰
⑯
Connection to the ports
C
HDMI 1, DHDMI 2
HDMITM connector
CD
E
② ⑥ ⑩⑨⑧
① ⑤④③
⑦ ⑪ ⑮⑭⑬⑫⑲⑱⑰
Pin Signal Pin Signal Pin Signal
1 T.M.D.S. Data2 + 8 T.M.D.S. Data0 Shield 15 SCL 2 T.M.D.S. Data2 Shield 9 T.M.D.S. Data0 - 16 SDA 3 T.M.D.S. Data2 - 10 T.M.D.S. Clock + 17 DDC/CEC Ground
18
4 T.M.D.S. Data1 + 11 T.M.D.S. Clock Shield 5 T.M.D.S. Data1 Shield 12 T.M.D.S. Clock -
+5V Power
19 Hot Plug Detect 6 T.M.D.S. Data1 - 13 CEC 7 T.M.D.S. Data0 + 14 Reserved (N.C. on device)
⑯
E
DVI-D
DVI-D jack (digital to digital)
Pin Signal Pin Signal Pin Signal
1 T.M.D.S. Data2 - 9 T.M.D.S. Data1 - 17 T.M.D.S. Data0 ­2 T.M.D.S. Data2 + 10 T.M.D.S. Data1 + 3 T.M.D.S. Data2/4 Shield 11 T.M.D.S. Data1/3 Shield 19 T.M.D.S. Data0/5 Shield 4 - 12 ­5 - 13 - 21 ­6 DDC Clock 14 +5V Power 22 T.M.D.S. Clock Shield 7 DDC Data 15 Ground (for +5V) 23 T.M.D.S. Clock + 8 - 16 Hot Plug Detect 24 T.M.D.S. Clock -
DWU1052/DHD1052 User's Manual - Technical
8
18
T.M.D.S. Data0 +
20
-
020-000857-01 Rev. 1 (12-2015)
Connection to the ports
Connection to the ports
VIDEO
F
G
F
BNC jack
• Composite video signal, Analog, 1.0±0.1Vp-p, 75Ω terminator
• System: NTSC, PAL, SECAM, PAL-M, PAL-N, NTSC4.43, PAL(60Hz)
G
CONTROL
D-sub 9pin plug * About the details of RS-232C communication,
⑤ ④ ③
⑥⑦⑧⑨
①②
refer to the next section.
Pin Signal Pin Signal Pin Signal
1 (No connection) 4 (No connection) 7 RTS 2 RD 5 Ground 8 CTS 3 TD 6 (No connection) 9 (No connection)
DWU1052/DHD1052 User's Manual - Technical
9
020-000857-01 Rev. 1 (12-2015)
Connection to the ports
①⑤④③
②⑥⑧
⑦
①⑤④③
②⑥⑧
⑦
Connection to the ports
H
HDBaseT
RJ-45 jack
② ⑥ ⑧
① ⑤④③
Pin Signal Pin Signal Pin Signal
1 HDBaseT0+ 4 HDBaseT2+ 7 HDBaseT3+ 2 HDBaseT0- 5 HDBaseT2-
8 HDBaseT3-
3 HDBaseT1+ 6 HDBaseT1-
H
I
⑦
I
LAN
RJ-45 jack
② ⑥ ⑧
① ⑤④③
Pin Signal Pin Signal Pin Signal
1 TX+ 4 - 7 ­2 TX- 5 -
8 -
3 RX+ 6 RX-
DWU1052/DHD1052 User's Manual - Technical
10
⑦
020-000857-01 Rev. 1 (12-2015)
Connection to the ports
① ④③②
Connection to the ports
M
K
J
WIRELESS
①④ ③ ②
Only for USB wireless adapter.
Pin Signal
1 +5V 2 - Data 3 + Data 4 Ground
REMOTE CONTROL KIN, LOUT
Ø3.5 stereo mini jack
M
SDI/DIGITAL1
BNC jack x1
• SD/HD/3G-SDI signal, Digital, 0.8V±10%, 75Ω terminated
• System: SD-SDI signal: conforming to SMPTE ST 259-C standard
YCBCR 4:2:2 10-bit 480i, 576i
Single link HD-SDI signal: conforming to SMPTE ST 292 standard
YPBPR 4:2:2 10-bit 720p@50/60, 1080i@50/60, 1080sf@25/30
3G-SDI Level-A signal: conforming to SMPTE ST 424 standard
YPBPR 4:2:2 10-bit 1080p@50/60
J
L
DWU1052/DHD1052 User's Manual - Technical
11
020-000857-01 Rev. 1 (12-2015)
RS-232C Communication
RS-232C Communication
When the projector connects to the computer by RS-232C communication, the projector can be controlled with RS-232C commands from the computer.
For details of RS-232C commands, refer to RS-232C Communication / Network command table (
&21).
Connection
Turn off the projector and the computer.
1.
Connect the projector's CONTROL port and the computer's RS-232C port
2.
with a RS-232C cable (cross). Use the cable that ful lls the speci cation shown in  gure.
Turn the computer on, and turn the projector on after the computer has started up.
3.
Set the COMMUNICATION TYPE to OFF in the COMMUNICATION menu of the
4.
OPTION - SERVICE menu.
DWU1052/DHD1052 User's Manual - Technical
RS-232C
RS-232C cable
(cross)
RS-232C port
of the computer
9876
1
5432
CD (1) (1) RD(2) (2) RD TD (3) (3) TD DTR (4) (4) GND (5) (5) GND DSR (6) (6) RTS (7) (7) RTS DTS (8) (8) CTS RI (9) (9)
12
CONTROL
CONTROL port
of the projector
⑥⑦⑧⑨
①②
⑤ ④ ③
－
－
－
－
020-000857-01 Rev. 1 (12-2015)
Communication settings
1. Protocol
19200bps, 8N1
2. Command format
(h shows hexadecimal)
RS-232C Communication
Byte Number
Command
Action
<SET>
Change setting to
desired value [(cL)(cH)]
by [(bL)(bH)].
<GET>
Read projector internal setup value [(bL) (bH)] .
<INCREMENT> Increment setup value
[(bL)(bH)] by 1.
<DECREMENT> Decrement setup value
[(bL)(bH)] by 1.
<EXECUTE> Run a command [(bL)(bH)].
0 1 2 3 4 5 6
Header Data
Header
code
L H L H L H L H L H L H
BEh EFh 03h 06h 00h
Packet
Data
size
CRC
ag
(aL) (aH) 01h 00h (bL) (bH) (cL) (cH)
(aL) (aH) 02h 00h (bL) (bH) 00h 00h
(aL) (aH) 04h 00h (bL) (bH) 00h 00h
(aL) (aH) 05h 00h (bL) (bH) 00h 00h
(aL) (aH) 06h 00h (bL) (bH) 00h 00h
7 8 9 10 11 12
Action Type
[Header code] [Packet] [Data size]
Set [BEh, EFh, 03h, 06h, 00h] to byte number 0 to 4.
[CRC ag]
For byte number 5 and 6, refer to
command table
(&21).
RS-232C Communication / Network
[Action]
Set functional code to byte number 7 and 8. <SET> = [01h, 00h], <GET> = [02h, 00h], <INCREMENT> = [04h, 00h] <DECREMENT> = [05h, 00h], <EXECUTE> = [06h, 00h]
Refer to the Communication command table (
&above).
[Type] [Setting code]
For byte number 9 to 12, refer to RS-232C Communication / Network
command table (
&21).
Setting
code
DWU1052/DHD1052 User's Manual - Technical
13
020-000857-01 Rev. 1 (12-2015)
Loading...
+ 31 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use