MODEL
USER MANUAL
WFL8TOL52W
Thank you for choosing CHiQ brand washing machine.
Technical date
Model
WFL8TOL52W
Before beginning installation, read these instructions carefully. This will simplify installation and
ensure that the product is installed correctly and safely. Leave these instructions near the
product after installation for future reference.
This manual may contain images or content different from the model you purchased.
This manual is subject to revision by the manufacturer.
Rated washing capacity (kg) 8
Rated voltage 220--240V～
Rated frequency 50Hz
Rated power (W) 2000
Washing noise level (dB) 62
Spinning noise level (dB) 76
Spin speed (rpm) 1400
Water pressure (MPa) 0.03 ～ 1.0
Waterproofing grade IPX4
Water consumption
(litres per wash)
Energy consumption
(kWh per year)
Net weight (kg) 65
Outer dimension
(WxDxH mm)
81
308
600 X 577 X 847
Safety instruction. 2-3-4-5
Safety instruction
Disposal
Installation. 6-7-8-9
Unpacking,
Remove the transport bolts
levelling
Choosing the right location
Connecting the electricity and water supplies
Technical date
Description of the washing machine. 10-11
Control panel
Display
Preparing and sorting laundry. 12-13
Preparing the laundry
Sorting the laundry according to colour and degree of soiling
Sorting laundry according to their care label specifications
Wash cycles and options. 14-15
Table of wash cycles
M. Smart wash cycle
Ozone program
Drum lamp
Stains removal
How to use the appliance. 16-17-18
Before loading your first load of laundry
Daily use
Preparing the laundry
How to use the washing machine
Care and maintenance. 19-20-21
Cutting off water and electricity supplies
Cleaning the appliance’s exterior
Cleaning the drum
Descaling the washer
Caring for the door and drum of your appliance
Checking the water inlet hose
Cleaning the detergent dispenser
Cleaning the water inlet strainers
Cleaning the drain pump
Troubleshooting. 22-23-24
1
Safety instruction
Before using the appliance, read these safety
instructions. Keep them nearby for future reference.
These instructions and the appliance itself provide
important safety warnings, to be observed at all
times. The manufacturer declines any liability for
failure to observe these safety instructions, for
inappropriate use of the appliance or incorrect
setting of controls.
Young children (0-3 years) should be kept away from
the appliance. Young children (3-8 years) should be
kept away from the appliance unless continuously
supervised. Children from 8 years old and above
and persons with reduced physical, sensory or
mental capabilities or lack of experience and
knowledge can use this appliance only if they are
supervised or have been given instructions on safe
use and understand the hazards involved. Children
must not play with the appliance. Cleaning and user
maintenance must not be carried out by children
without supervision. Keep all laundry aids (including
detergent, bleach, fabric softener, etc.) out of the
reach of children.
PERMITTED USE
CAUTION: The appliance is not intended to be
operated by means of an external switching device,
Such as a timer, or separate remote controlled
system.
This appliance is intended to be used in household
and similar applications, it is not in applications
such as: staff kitchen areas in shops, offices and
other working environments; farm houses; by
clients in hotels, motels, bed & breakfast and Areas
for communal use in blocks of flats or in
launderettes.
Do not load the machine above the maximum
capacity (kg of dry cloth) indicated in the program
table.
This appliance is not for professional use. Do not
use the appliance outdoors.
Do not use any solvents (e.g. turpentine, benzene),
detergents containing solvents, scouring powder,
glass or general purpose cleaner, or flammable
fluids; do not machine wash fabric that have been
treated with solvents or flammable liquids.
Do not machine wash fiberglass materials (such
2
as curtains and windows coverings that use
fiberglass materials). Small particles may remain in
the washing machine and stick to fabrics in
subsequent wash loads causing skin irritation.
Fabric softeners, or similar products, should be used
as specified by the fabric softener instructions.
Remove all objects from packets such as lighters and
matches.
Make sure there is no water in the drum before
opening the door.
Never wash the carpet in the washing machine.
Keep pets away from the washing machine.
Exercise caution when pumping out hot detergent
solution.
Do not fill water during washing cycle manually.
Please close the loading door correctly, if it is
difficult to close it, please check if the laundry is
caught in the door.
Water may reach very high temperatures during the
wash cycle.
Do not reach into the appliance if the wash drum is
moving.
Do not temper with the controls.
Never open the door forcibly or use it as a step.
Do not allow anyone to climb, lean or hang on any
part of the washing machine including any
protruding components such as the appliance door
or a pullout shelf.
Safety instruction
INSTALLATION
The appliance must be handled and installed by two
or more persons – risk of injury. Use protective
gloves to unpack and install – risk of cuts.
The washing machine must be installed and
operated in a room with a drain.
Installation, including water supply (if any) and
electrical connections and repairs must be carried
out by a qualified technician. Keep children away
from the installation s ite. After unpacking the
appliance, make sure that it has not been damaged
during transport. In the event of problems, contact
the dealer or your nearest After-Sales Service. Once
installed, packaging waste (plastic, Styrofoam parts
etc.) must be stored out of reach of children – risk
of suffocation. The appliance must be disconnected
from the power supply before any installat ion
operation – risk of electric shock. During installation,
make sure the appliance does not damage the
power cable – risk of fire or electric shock. Only
operate the appliance when the installation has
been completed.
Do not install your appliance where it may be
exposed to extreme conditions, such as: poor
ventilation, temperatures below 5 ℃ or above
35℃.
Do not expose the washing machine in the place
with causticity or explosibility gas.(e.g. dust, steam
and gas, etc.)
Do not install the washing machine in a bathroom
or a room very wet.
The washing machine should not be installed in an
outdoor environment, not even where the area is
sheltered, because it may be very dangerous to
leave it exposed to damp, rain and thunderstorms.
When installing the appliance make sure that the
four feet are stable and resting on the floor,
adjusting them as required, and check that the
appliance is perfectly to level using a spirit level.
The appliance must not be installed behind a
lockable door, a sliding door or a door with a hinge
on the opposite side to that of the washer dryer, in
such way that a full opening of the washer-dryer
door is restricted.
Make sure that the ventilation openings in the base
of your washing machine (if available on your model)
are not obstructed by a carpet or other material.
When moving, do not lift the washing machine by
the knobs or detergent drawer, without lifting it by
the worktop or top lid; during transport, never rest
the door on the trolley.
The washing machine is fitted with transport bolts
to prevent any possible damage to the interior
during transport. Before using the machine, it is
imperative that the transport bolts are removed.
After their removal, cover the openings with the 4
enclosed plastic caps.
Connect the water inlet hose(s) to the water supply
in accordance with the regulations of your local
water company.
Use only the new hose-sets supplied with the
appliance to connect the appliance to water supply.
The old hose-sets should not be reused.
The supply water pressure must be in the
0.03—1MPa range,
3
Safety instruction
ELECTRICAL WARNING
It must be possible to disconnect the appliance from
the power supply by unplugging it if plug is
accessible, or by a multi-pole switch installed
upstream of the socket in accordance with the
wiring rules and the appliance must be earthed in
conformity with national electrical safety standards.
When the washing machine is installed, the mains
s o c k e t m u s t b e w i t h i n e a s y r e a c h .
Do not pull on the power cord or appliance to
unplug the machine.
When heating, the maximum current of the washing
machine is 10A, so please make sure that the power
supply system (voltage, current and the cable) is
applicable to the load of the applied appliance.
In order to ensure your safety, you must plug the
cable into a socket which connected to earth. And
please check your socket to make sure that it is
connected with reliable earth correctly.
Do not use extension leads, multiple sockets or
adapters.
The electrical components must not be accessible to
the user after installation.
Do not operate this appliance if it has a damaged
power cable or plug, if it is not working properly, or
if it has been damaged or dropped.
If the supply cord is damaged, it must be replaced
with an identical one by the manufacturer, its
service agent or similarly qualified persons in order
to avoid a hazard – risk of electric shock.
CLEANING AND MAINTENANCE
WARNING: Ensure that the appliance is switched off
and disconnected from the power supply and turn
off the water tap before performing any
maintenance operation; never use steam cleaning
equipment – risk of electric shock.
Use caution when draining hot water from the drum
such as during pump maintenance or when using
emergency door open procedure.
4
SERVICE
Do not repair or replace any part of the appliance
unless specifically stated in the user manual. Use
only authorized After-sales Service. Self or
non-professional repair may lead to dangerous
incident resulting in live or health threatening
and/or significant property damage.
In the event of fault and/or malfunction, turn off
the washing machine, close the water tap and do
not tamper with the machine. Immediately contact
the Customer Service Centre and only use original
spare parts.
Always unplug the washer-dryer from the power
supply before attempting any service. Disconnect
the power cord by grasping the plug, not the cord.
Before the appliance is removed from service or
discarded, remove the door to prevent children
from playing or hiding inside. Also remove the
power cord/plug.
Installation
DISPOSAL OF PACKAGE MATERIALS
The packaging material is 100% recyclable and is
marked with the recycle symbol .
The various parts of packaging must therefore be
disposed of responsibly and in full compliance with
local authority regulations governing waste
disposal.
DISPOSAL OF HOUSEHOLD APPLIANCES
This appliance is manufacture with recyclable or
reusable materials. Dispose of it in accordance with
local waste disposal
regulations. For further information on the
treatment, recovery and recycling of household
electrical appliances, contact your local authority,
the collection service for household waste or the
store where you purchased the appliance. This
appliance is marked in compliance with European
Directive 2012/19/EU. Waste Electrical and
Electronic Equipment (WEEE). By ensuring this
product is disposed of correctly, you will help
prevent negative consequences for the environment
and human health.
The symbol on the product or on the
accompanying documentation indicates that it
should not be treated as domestic waste but must
be taken to an appropriate collection center for the
recycling of electrical and electronic equipment.
5
Installation
Unpacking
1. Remove the washer from its packing.
2. Make sure that the washer has not been
damaged during the transportation process. If it
has been damaged, contact the retailer and do
not proceed any further with the installation
process.
Remove the transport bolts
CAUTION
DAMAGE TO THE APPLIANCE OR INJURY POSSIBLE
The machine is secured for transport with
transport bolts. Transport bolts that are not
removed can damage the drum during operation
of the machine, the washer will vibrate, and it
will be much noisier during spin cycles if the
transport bolts are not removed before use. Be
sure to remove all 4 transport bolts completely
before first use. Keep the transport bolts. If a
pedestal was purchased with the washer, it must
be installed first, prior to removing the transport
bolts. Please consult the pedestal installation
instructions.
In order to prevent transport damage during later
transport, be sure to re-install the bolts before
transport.
1. Undo the four transport bolts A and remove
them.
2. Remove the four spacers B. They will fall to the
floor when you tip the machine.
3. Insert the four cover caps C which will be found
in accessory bag.
6
Keep all the parts in safe place: you will need them
again if the washing machine needs to be moved to
another location.
Packaging materials should not be used as toys for
children.
Leveling the washer
Importance of leveling the washer
Your new washer uses high spin speeds to remove
water at the end of the wash cycle. It is important
that your washer is level and that all four washer
feet press with equal pressure against the floor. This
will help assure the quietest, most vibration-free
use of your washer.
Follow these steps:
1. Install the washer on a level and solid surfaces.
Preferably in a corner of a room.
2. If the floor is uneven (or out of level ) adjust the
washer feet as required to level the washer. Do
not place anything under the washer feet to help
level the washer.
3. Extend the washer feet no more than is
necessary. The more the feet are extended, the
more vibration the washer will experience. Start
with the washer feet turned all the way in and
adjust each foot as necessary.
4. Use a bubble level to check the top of the washer
to make sure it is level side to side and front to
rear.
5. Press down on each corner of the washer top to
make sure the washer doesn’t “wobble”. There
should be no “give” or movement. All four
washer feet should press equally against the floor.
This is just as important as the washer being level
to prevent vibration.
6. When the washer is level and does not wobble,
lock the washer feet in place by tightening the
locknuts against the washer bottom. Be sure to
do this without changing the height of the foot
(hold the foot while tightening the locknut)
Installation
Procedure for adjusting the washer feet:
1. After determining which washer feet need to be
extended, have someone lift up on the washer
slightly to take pressure off the foot to be
adjusted.
2. Turn the grey plastic foot to extend it downward
as far as necessary to raise the corner of the
washer the correct amount to level the washer.
3. When the height of the foot is correct, use a 17
mm open end wrench to tighten the locknut
against the washer bottom. The locknut should
be tighten against the bottom of the washer to
lock the foot in place.
Choosing the Right Location
● Locations the appliance is not to be
installed
In a damp place or where the appliance may be
-
exposed to rain, etc.(As this could cause electric
shock or fire)
Locations that are uneven, or unstable (As this
-
could cause vibration and noise).
In direct sunlight (As this could cause malfunction
-
or deformation)
Within, or on top of, unstable surfaces, including
-
but not limited to benchtops, timber shelving, or
cabinets
！
● Set-in Installation
-
-
(a) 3cm or more
(b)
(c)
(d)
(e)
！
CANTION: Do NOT install where temperatures
may reach freezing
Install the appliance with easy access to the
power plug and socket.
Install the appliance where there is enough space
around it.
above
5cm or more
behind
2cm or more on
the left side
2cm or more on
the right side
64cm or more
CAUTION: Do NOT let metallic portions of the
appliance come into contact with metal sinks or
other appliances.
7
Installation
Connection the electricity and water
supplies
Connecting the water inlet hose
1. Connect one end of
the water inlet hose
by screwing it to a
cold water tap using a
3/4 gas threaded
connection (see
figure).
Before performing
the connection, allow
the water to run freely until it is perfectly clear.
2. Connect another
end of the water inlet
hose to the washing
machine by screwing
it onto the
corresponding water
inlet of the appliance,
which is situated on
the top right-hand
side of the rear part of the appliance (see figure)
3. Make sure that the hose is not folded over or
bent.
The supply water pressure must be in the
0.03—1MPa range, the values indicated in the
Technical date table (see page 8).
If the inlet hose is not long enough, contact a
specialized shop or an authorized technician.
Never use second-hand water inlet hoses.
Use the new water inlet hose supplied with the
machine.
Connecting the
drain hose
Connect the drain
hose, without
bending it, to a
draining duct or a
wall drain situated
between 65 and
100cm from the floor;
The drain hose may be
connected to an under
sink trap. Before
connecting the drain
hose from the machine
ensure that any blanks
or removable ends
have been taken off
the spigot,
If it is placed over the
edge of the basin or
sink be sure the free
end of the hose
should not be under
water tap.
8
Installation
Electric connection
Before plugging the appliance into the mains socket,
make sure that:
· The socket is earthed and in compliance with the
applicable law.
· The socket is able to sustain the appliance’s
maximum power load indicated on the Technical
Date Plate fixed on the machine.
· The supply voltage is included within the values
indicated on the Technical Date Plate fixed on the
machine.
· When heating, the maximum current of the
washer-dryer is 10A, so please make sure that
the power supply system (voltage, current and
the cable) is applicable to the load of the applied
appliance.
· The socket is compatible with the washer’s plug.
If this is not the case, replace the socket or the
plug by a qualified electrician.
WARNING----THIS APPLIANCE MUST BE EARTHED.
THE FOLLOWING OPERATIONS SHOULD BE
CARRIED OUT BY A QUALIFIED ELECTRICIAN.
Do not use extension cables, multiple sockets or
adapters.
To remove the plug from the socket, grasp the
plug firmly and pull it out. Do not pull at the cable.
The electrical components must not be accessible
to the user after installation.
Do not connect the machine to electrical outlets
while your hands are wet or damp.
Do not operate this appliance when you are wet or
barefoot.
Do not operate this appliance if it has a damaged
power cable or plug, if it is not working properly, or
if it has been damaged or dropped.
WARNING! The company denies all liability if and
when these norms are not respected.
The water consumption of a cold wash cycle is no higher
than a warm cycle.
9
Description of the appliance
Control panel
A---WASH CYCLE SELECTOR KNOB: Used to set the
desired wash cycle (see “Table of wash cycles”).
· OFF position : Turn the knob to the “ ”
position to switch the machine off. If the machine is
switched off during a wash cycle, this wash cycle will
be cancelled.
B---TEMPERATURE button: Press to change the
water temperature for the current cycle, with the
changed temperature value appears on digital
display.
C---SPEED button: Press to change the spinning
speed for the current cycle, with the changed
spinning speed value appears on digital display.
· CHILD LOCK function: When the cycle is running,
if you want to activate the control panel lock, please
press and hold the SPEED button for approximately
3 seconds. When the indicator light is
illuminated, the control panel is locked. This means
it is possible to prevent wash cycles from being
modified accidentally, especially where there are
children in the home.
To deactivate the control panel lock, press and hold
SPEED button for approximately 3 seconds.
· Cancelling the buzzer:
Press and hold the SPEED button and ONE TOUCH
button together at the same time for at least 3
seconds, you can turn off the buzzer that sounds
during the washing cycle running.
· To activate the buzzer setting
Do the same operation as you did for cancelling. The
buzzer setting is activated after one beep.
10
D---OZONE button:
· Short press to select the ozone function, the
washer will process the OZONE program only
after the final spin cycle
· Long press to run the OZONE program directly.
Some programs cannot select the OZONE program.
E---RINSE button: Press to change the rinse
count for the current cycle, the changed rinse count
appears on digital display.
F---DELAY END button: Press to set the washer to
finish the selected wash cycle automatically at later
time. Choose a delay of 1 to 24 hours (in 1 hour
increments).
The hour value appears on digital display indicates
the time the wash cycle will finish.
The way to cancel Delay End function:
· Turn the wash cycle knob to reset the wash cycle.
G---ONE TOUCH button: Press to set the
M-Smart wash cycle.
For a detailed description, see→ Wash cycle and
options.
H---START/PAUSE button:
· Long press the button to start a wash cycle.
· Once the cycle has begun, if you want to pause
the wash cycle, please long press the button again.
If the DOOR LOCK symbol is not illuminated,
the door may be opened, you can add or take out
laundry.
To start the wash cycle from the point at which it
was interrupted, press the button again.
Description of the appliance
M-Display
The display is useful when programming the machine and provides a great deal of information.
1---Temperature indicator
When a program is selected, the default
temperature value of this program will appears on
the display, with the corresponding temperature
indicator light illuminated.
You can change the temperature value by pressing
the TEMPERATURE button. If all temperature
indicator light are off, it indicated the washer using
only cold water without utilized the washer’s heater
in this program.
2---SPINNING SPEED indicator
When a program is selected, the default spinning
speed value of this program will appears on the
display, with the corresponding spinning speed
indicator light illuminated.
You can change the spinning speed value by
pressing the SPEED button. If all spinning speed
indicator light are off, it indicate the washer does
not spin after the final drain process in this
program.
3---DOOR LOCK indicator
The lit symbol indicates that the door is
locked. To prevent any damage, wait
until the symbol turns off before opening the door.
To open the door while a cycle is in progress, press
the START/PAUSE button, if the DOOR LOCK symbol
is switched off the door may be opened.
4---CHILD LOCK indicator
The lit symbol indicates the CHILD LOCK
function is activated, the control panel is
locked (apart from the OFF position on the control
panel).
5---DELAY END indicator
The lit symbol indicates the DELAY END
function is activated. The countdown to
the end of the selected wash cycle will appear on
the digital display.
6---ONE TOUCH indicator
The lit symbol indicates the M-Smart
wash program is selected. There are three
ways to set the M-Smart wash program.
7---RINSE COUNT indicator
When the symbol lit, you can select the
rinse count, the selected rinse count will
appear on the digital display.
8---OZONE FUNCTION indicator
The lit symbol indicates that the OZONE
function is activated.
9---STAIN TYPE indicator
The STAIN TYPE symbol lit indicates the type of dirt
has been selected, the washer will optimally adjust
the cycle for removing the stains.
10---DIGITAL DISPLAY
1) Wash cycle
remaining
time
2) Delay end time
3) Temperature
4) Spin speed
5) Rinse count
6) Fault code
11
Preparing and sorting the laundry
Preparing the laundry
Notice: Damage to the appliance/fabric
Foreign objects (e.g. coins, paper-clips, needles,
nails) may damage the laundry or components in
the washing machine.
Therefore, note the following tips when preparing
your laundry:
Remove any loose
items or metal objects,
such as safety pins,
paper clips, etc. from
the laundry.
Brush sand, coins, etc. out of pocket and cuffs.
Close zips and button
up cushion covers,
duvet covers, etc.
Remove curtain runners, or secure them in a net
bag.
Particularly delicate items; such as tights or lace
curtains, or smaller
items, such as tiny
socks or handkerchiefs,
should only be
washed in a net bag or
pillow case.
Some items are best
turned inside out.
These included
knitwear, trousers,
T-shirts and
sweatshirts.
Make sure that the wire-cup bras are machine
washable.
! Make sure that wire-cup bras in a pillow case
which can be securely closed with a zip or button.
If the wire works itself out of the cup it may fall
through the holes of the drum and cause
extensive damage.
12
Sorting the laundry according to
colour and degree of soiling
Sort laundry items according to color, degree of
soiling and recommended wash temperature range.
Items of clothing can become discoloured.
Never wash new muti-coloured items together
with other items.
Wash white items separately from colored items.
Otherwise, white items may tend to become
grey.
Degree of soiling
Light soiling
No visible soiling or stains, but may have
absorbed some odor. This could include light
weight summer clothes such as T-shirts, shirts, or
blouses worn only once. Also to freshen bed
linen or guest towels
Normal soiling
Visible soiling and/or a few light stains. This could
include clothing such as T-shirts, shirts, or
blouses that nave been sweated in or worn
several times. Also tea towels, hand towels or
bed linen used for up to one week or more.
Curtains without stains that have not been
washed for up to a half year.
Heavy soiling
Visible soiling and stains. This could include
kitchen towels, fabric napkins, baby bibs,
children’s outer clothing or football jerseys and
shirts stained with grass or dirt. It could also
include working clothes such as overalls and
jeans and other clothing worn for outside work
and activities.
Preparing and sorting the laundry
Sorting laundry according to their
care label specifications
The symbols on labels of your garments will help
you in choosing the suitable wash program, the
right temperature, wash cycles, and ironing
methods. Don’t forget to give a glance to these
useful indications!
13
Wash cycles and options
Wash cycle
Max.
Load
(kg)
Description
Kind of detergent
Detergents
softe
ner
Universal
Special
Table of wash cycle
Temp.
℃
(Max)
Cotton 60 8 For pure cotton clothes L / P --- O
Allergy care 85 3
Mix 60 8
Wool 40 1
Baby care 85 5 For kid's wear L / P L O
Down Jacket 40 2
Underwear 60 4 For underwear. L / P L O
Bedding 60 5
Quick wash 40 1
Sanitize 85 3
Delicate 40 3 For washing delicate or soft clothes L / P --- O
Night
Special
Deep clean 60 8 For heavily soiled clothes L / P --- O
Rinse +Spin --- 8
Spin --- 8 For clothes which just needs spin --- --- ---
Drum clean 85 ---
M-Smart 40 5
L=gel-/liquid detergent P=Powder detergent O=Optional ---=No
If using liquid detergent, it is not recommended to activate the time delay.
Please follow the dosage recommendation on the powder or liquid detergent package.
We recommend by using:
Laundry powder 20℃ to 80℃
Wool detergent 20℃ to 40℃
Cotton, 40℃, 1400rpm and the intense option selected is recommended water and energy saving cycle for
normally soiled, everyday washing.
The detergent dosage: rated capacity*12.5g*75% and anti-foam aid is 16g.
Detergent dissolvent method: Dissolve the detergent first and pour the dissolved detergent into the machine
when the main wash starts.
14
60 8 For washing clothes in night L / P --- O
For clothes that need to remove
mites and allergens.
For mixed washing of cotton, linen
and chemical fiber fabrics
For wool which can be washed by
machine
For down jacket which can be
washed by machine
For large items such as blankets,
curtains and bedspreads
For small amount or lightly soiled
garments
For clothes needing sterilization
and decontamination
For clothes which just needs rinse
and spin
For cleaning the drum, no clothes in
drum
Special cycle which can be started
simply by pressing the ONE-TOUCH
button once.
L / P --- O
L / P --- O
--- L / P O
--- L / P O
L / P --- O
L / P --- O
L / P --- O
--- --- O
--- --- ---
L / P --- O
Wash cycles and options
M-Smart wash cycle
M-Smart wash cycle can intelligently detect the
weight of laundry and match different washing time
and temperature to realize intelligent washing.
" " is displayed in the detection stage after
the cycle is started, and the M-Smart wash cycle can
be entered by the following three methods.
When the washer is OFF, press and hold the
ONE-TOUCH button for at least 3 seconds, the
washer will run the M-Smart wash cycle directly,
with M-Smart indicator light illuminated.
Wh en the w ash er is ON , pre ss an d hol d
ONE-TOUCH button for at least 3 seconds, the
washer will run the M-Smart wash cycle directly,
with M-Smart indicator light illuminated.
Wh en t he wash er is O N, short press t he
ONE-TOUCH button, the M-Smart indicator light
illuminated, and then press the
START/PAUSE button, the washer runs the
M-Smart wash cycle.
Ozone program
When running the Ozone program, the water does
not fill into the machine, and the clothes are treated
with ozone. Two different Ozone programs can be
selected according to the following methods
1. Selection "Washing + Ozone" program
According to the type of clothes, select the
appropriate washing program. Short press the
"OZONE" button, and the running time of the
program displayed on the digital display will
increase correspondingly, indicating that the Ozone
function has been selected. If you want to cancel
Ozone function, short press the "OZONE" button
again
2. Selection Ozone program only
When cleaning the object (the surface of the object
should be free of oxidation and fading coating or ink
printed font or pattern), you can choose to run the
Ozone program only for cleaning. After the clothes
are put in, close the door, turn on the power, turn
the knob to turn on the machine, and press and
hold the button until the sound comes up, and the
Ozone program starts to run
Precautions for Ozone program
When running the Ozone program, ozone may
cause color fading on the surface of dark or easily
faded clothes or articles. It is recommended that:
---Only for cleaning white or light colored clothes.
---It is only used for the cleaning treatment of
objects without easy oxidation and fading coating or
printing characters or patterns with ink.
---The no fading and easy fading parts on the
clothes or objects to be cleaned must be separated
before ozone cleaning.
Drum lamp
How to turn on the drum lamp:
1. During selecting the wash cycle or setting the
wash option, the drum lamp is lighting.
2. When the machine running is paused, you can
turn on the drum lamp through opening the
door, and the drum lamp will go off 20
seconds later.
3. When the machine is running, you can turn on
the drum lamp by pressing any button.
4. When the machine is running, the drum lamp
will light automatically for a good washing
effect.
Stains removal
This option allows for selecting the type of dirt so as
to optimally adjust the cycle for removing the stains,
there are eight types of stains to choose from:
The washer adjusts the average washing
temperature, drum movement and soaking time to
the specific type of stain. Hot or cold water, gentle
or intensive washing and long or short soaking
ensure that the wash cycle sequences specially
adapted to each type of stain. Selecting this option
make sure that stains are treated in the best
possible way.
NOTICE: Pressing and holding the button
automatically runs through the set type of stains.
The wash cycle duration varies according to the type
of selected dirt type.
Oils , Food
based
Juice
Pigment
Blood
Milk
Red wine
Mud
Grass
15
How to use the appliance
Before loading your first load of
laundry
Your new washing machine was tested before
leaving the factory. This process involves running
various wash cycles. As a result, a small amount of
water may remain in the tub and drainage system.
Run a Drum Clean cycle with no laundry to clean
the system before your first load of laundry.
First add 1 to 2 tablespoons of detergent to the
chamber I. Then run the Drum Clean cycle.
Wait for the cycle to finish.
Daily use
Preparing the laundry
EMPTY POCKETS
· Coins, paper clips, etc. could damage the load
and the washing machine components.
· Tissues will break down during the wash cycle
and the fragments will have to be subsequently
removed by hand.
CLOSE ALL ZIPPERS, BUTTONS, AND HOOKS. TIE
ALL RIBBONS OR BELTS
· Insert the smaller garments (e.g. nylon hosiery,
belts, etc.) and garments with hooks (e.g.
braziers) into a fabric bag or a pillowcase with
zipper. Remove any rings from curtains, or else
place the curtains inside a fabric bag together
with the rings.
FABRIC TYPE/SYMBOL ON THE WASH LABEL
· Cottons, mixed fibres, easy care/synthetics, wool,
hand wash items.
· Color
Separate colored and white items. Wash new
colored articles separate.
· Size
Wash items of different sizes in the same wash
load, to improve washing efficiency and
distribution of the articles in the drum.
· Delicates
Wash delicate items separately; they require
gentle treatment.
16
How to use the washing machine
1. Load laundry
Open the door and load the laundry. Load the
articles one at a time loosely into the drum,
without overfilling. Observe the load sizes given
in the “Table of wash cycle”, Overloading the
machine will result in unsatisfactory washing
results and creased laundry.
2. Close door
Make sure that no laundry gets stuck between
door glass and rubber seal. Close the door so that
you can hear it click shut.
3. Open water tap
Make sure that the washing machine is
connected to the water mains. Open the water
tap.
4. Set the desired program
Select the required program with the “Program
selector” knob. The duration of the wash cycle is
shown on the display. The washing machine
automatically displays the default temperature
and spin speed settings possible for the selected
program. Adjust the temperature and/or spin
speed setting if needed with the relative buttons.
· Change temperature, if needed
Press the “Temperature” button to progressively
lower the temperature setting until cold wash
has been set (“---“will be shown on the display).
Pressing the button again sets the highest
possible setting.
· Change spin speed, if needed
Press the “spin” button to progressively decrease
the spin speed until the spin cycle is turned off
(“---” will be shown on the display). Pressing the
button again sets the highest possible setting.
· Select options, if needed
Press the button to select the option; the
respective symbol on the display illuminates.
Press the button again to cancel the option; the
light extinguishes.
How to use the appliance
!If the selected option is incompatible with the
program set, the incompatibility will be signaled by
a buzzer (3 beeps) and the corresponding indicator
light will flash.
!If the selected option is incompatible with another
previously set option, only the most recent
selection will remain active.
5. Add detergent
Pull out the detergent dispenser and add
detergent (and additives/softener) into the
relative compartments as described below.
Compartment 1:
Powder washing
detergent
Compartment 2:
Liquid washing
detergent
The liquid detergent
must not exceed the
“MAX” level.
Compartment 3:
Additives (Softener. etc.) The fabric softener must
not exceed the “MAX” level.
Observe the dosing recommendations on the
detergent pack.
Correct dosing of detergent/additives is important,
because:
· It optimizes the cleaning result
· It avoids irritating residues of surplus detergent
in your laundry
· It saves money by avoiding waste of surplus
detergent
· It protects the washing machine by avoiding
calcification of components
· It respects the environment by avoiding
unnecessary environmental burden.
! Do not use hand washing detergents because
these create too much foam.
! Use powder detergent for white cotton garments,
for pre-washing, and for washing at temperatures
over 60℃.
! Follow the instructions given on the detergent
packing.
6. Delaying the end of a program
· To set a program to end at a later time, see the
section “Control panel / DELAY END”.
7. Start program
· Press the “Start/Pause” . The relative
indicator lamp illuminates, the door locks and the
“Door locked” indicator lights up.
· To avoid overflow, do not open the detergent
dispenser during a running program anymore.
· The remaining program duration can vary. Factors
like unbalance in the wash load, or foam
formation, can have an effect on the program
duration.
8. Change the settings of a running program, if
needed
You can still change the settings while a program
is running. The changes will be applied, provided
the respective program phase has no finished
yet.
To change the settings of a running program:
· Press “Start/Pause” to put the running
program on pause.
· Change your settings.
· Press “Start/Pause” again to continue the
program.
If you have changed the program, do not add
detergent for the new program.
To prevent that a running program is changed by
accident (for instance by children), use the
“CHILD LOCK” (see section “Control panel /
SPEED”).
17
How to use the appliance
Pause a running program and open the door, if
needed
Press “Start/Pause” to pause a running
program.
Provided water level or temperature is not too high,
the “Door lock” indicator light turns off. You
can open the door, for example to add more laundry,
or to remove laundry which was loaded by mistake.
Press “Start/Pause” to proceed with the
program.
9. Cancelling a running program, if needed
· Turn the programme selector knob to “OFF”
position until the washing machine stops.
· If the water level and temperature are low
enough, the door unlocks may be opened.
· The door remains locked if there is water in the
drum. To unlock the door, switch the washing
machine on, select the “Spin” program and turn
the spin option off by setting the spin speed to
“--”.
· The water is emptied and the door unlocks at the
end of the program.
10. Switch off the washing machine after
program End
· At the end of the cycle, the message “End” is
shown on the display.
· The door can only be opened when the symbol
“Door locked” light turns off.
· Check that the “Door locked” indicator is off,
then open the door and take out the laundry.
· Turn the programme selector knob to “OFF”
position to switch the washing machine off.
Leave the door ajar to let the interior of the washing
machine to dry.
18
Care and maintenance
Your appliance is designed to give you years of
service. Observe the following instructions to
maintain and protect your appliance and keep it in
top operating condition.
WARNING
RISK OF ELECTRIC SHOCK HAZARD
To avoid risk of electric shock always disconnect the
washer from the power outlet prior to cleaning.
Never clean the washer with a pressure washer.
Cutting off the water and electricity
supplies
Turn off the water tap after every wash cycle.
This will limit wear on the hydraulic system inside
the washing machine and help to prevent leaks.
Unplug the washing machine when cleaning it
and during all maintenance work.
Cleaning the appliance’s exterior
WARNING
RISK OF EXPLOSION
To avoid risk of explosion never clean the washer
with flammable solvents.
Clean the appliance’s exterior surface when
required as follows:
- Use hot soapy water or a mild (non-abrasive)
cleaning agent.
- Rub dry with a soft towel.
- Remove residue immediately.
- Do not use high pressure spray.
Cleaning the drum
Metallic debris left in the drum can product rust
spots on the drum. Never use steel wool to try to
remove these. Use a chlorine-free cleaning agent
and follow the manufacturer’s instructions.
Descaling the washer
Provided that you use correct amounts of detergent
with you wash loads, descaling is not necessary. If
descaling the washer drum does become necessary,
please follow the descaling product manufacturer’s
instructions.
Small amounts of descaling agent can be used to
remove white spots on the washer drum caused by
lime or mineral deposits or small amounts of rust
caused by metal objects left in the drum.
NOTICE: Descaling agents contain acids which may
attack parts of the washing machine and may
discolor the laundry.
Caring for the door and drum of your
appliance
· Always leave the porthole door ajar in order to
prevent unpleasant odours from forming.
19
Care and maintenance
Checking the water inlet hose
Check the inlet hose at least once a year. If there are
any cracks, it should be replaced immediately:
during the wash cycle, water pressure is very strong
and very stong and a cracked hose could easily spilt
open.
Never use second-hand hoses.
Cleaning the detergent dispenser
If there is a buildup of residual detergent or
additives, or if the softener compartment is not
rinsed out well enough, it may be helpful to clean
the dispenser.
1. Open the detergent dispenser tray fully. Press
down on the drawer catch (1) and pull the the
tray (2) from the washer housing.
2. Remove the liquid detergent cover (3) by
grasping it and pulling it upwards from the
detergent dispenser tray.
3. Clean the liquid detergent cover and the
detergent dispenser tray by holding it under
runing water. Lightly wipe away any remaining
detergent residue.
4. Attach the liquid detergent cover and slide the
detergent dispenser tray back in place and close
the tray securely.
Tip: Do not operate the washer without the
detergent dispenser tray in place. Always keep the
tray completely closed.
Cleaning the water inlet strainers
If the washer water supply slows or stops
completely, the water inlet strainer may be blocked.
Cleaning is recommended every 6 months in any
event to reduce chances of valve blockage in areas
using hard water.
20
Normal water pressure from your home, that
remains in the supply hoses after turning off the
taps, will cause a small amount of water to drip out
when you remove the water supply hose from the
back of the washer. Be sure to close the taps
completely before removing the supply hoses to
minimize the amount of water.
Clean the stainer at the water tap end of
the hose
1. Remove the hose from the tap.
2. Rinse the strainer under the running water. Look
at the strainer to see if any visible debris is still
present. Rinse again if necessary to remove the
debris.
3. Reconnected the hose to the tap.
Clean the strainer at the washer end of
the hose
1. Remove the hose from the inlet on the back of
the washer.
2. Using narrow pliers, grasp and pull the strainer
from the inlet port.
3. Rinse the strainer under running water.
4. Reconnect the hose to the back of the washer
and turn on the water tap. Check to see if water
flows by starting a warm water wash cycle.
NOTICE: Check for leaks to be sure the rubber
washers are seated at both ends of the water supply
hose and the connections are properly tightened.
Care and maintenance
Cleaning the drain pump
WARNING
RISK OF SCALDING
Risk of hot water injury to skin !
Allow the water to cool down prior to actuating the
emergency door lock release.
You are responsible for ensuring all safety
precautions are followed when draining water from
washer and/or manually opening the washer door.
It may be necessary to clean the washer drain pump
if the washer fails to drain (sound of the water being
pumped from the washer cannot be heard when
the washer should be draining and other nearby
drains, such as a sink, are draining properly).
The washer pump can become blocked by loose
debris (a good reason to check the drum and
remove any visible debris after each load). Fabrics
that give off large amounts of fluff may also cause
blockage.
To access the washer drain pump, the service cover
must first be removed (see steps below). With the
service cover removed, proceed as follows:
1. If the washer has not been drained, try to drain it
now. Turn the program selector knob to the
Spin/Drain, select Spin Speed to No Spin and
press the Start/Pause button. Wait a few
moments to let the cycle drain the water from
the drum. If the pump is totally blocked, the
water will be unable to drain and the cycle will
end.
2. Shut off the tap so that no more water flows in
and has to be drained. Switch the appliance off.
Unplug the power plug.
3. Open the service cover.
water into a suitable container (up to
5.3U.S.gallon/20 liters of water may be drained).
Pull the sealing cap from the hose and lay the
hose over the side of the container and allow the
water to finish draining from the drum. When
finished, replace the sealing cap into the end of
the hose and restore the hose to its storage
location.
5. Turn the pump cover counterclockwise to remove
it. A small amount of residual water may flow out
when the cover is removed. Clean the interior of
the pump hosing, removing any debris or foreign
objects. Check to be sure the impeller where at
the back of the pump housing can now turn
freely. Remove any lint, debris or detergent
residue from the threads of the pump cover and
the pump cover housing. Replace the pump cover
by screwing tightly into position. Handle must be
vertically.
6. Close the service cover. Wipe up any spilled
water.
4. Use the pull-out drain hose located in the pump
access opening to drain the remaining
21
Troubleshooting
Problem
Possible cause / solutions
The machine does not
swtich on
The wash cycle does not
start
The machine does not fill
with water or “E02” in the
display
The machine does not drain
or spin or “E03” in the
display
The machine does not spin
· The Spin Speed is set to “OFF”.
The program takes too long
M-Smart wash cycle does
not activate
The machine is noisy
· There will always be some motor, pump and drum noise during spin.
Your washing machine could occasionally fail to work. Before contacting the service center, make sure that the
problem cannot be solved easily using the following list
· The appliance is not plugged into the socket fully, or not enough to make
contact.
· There is not power to the socket, or the fuse has blown in the mains plug.
· The door is not closed properly.
· The ON/OFF button has not been pressed.
· The START/PAUSE button has not been pressed.
· The water tap has not been turned on to allow water to flow into the
machine.
· A delayed start has been set.
· The water inlet hose is kinked.
· The water inlet hose is not connected to the water supply.
· The water pressure is too low.
· The water tap has not been turned on to allow water to flow into the
machine.
· There is no water supply to the house.
· The inlet valve filter is blocked.
· The START/PAUSE button has not been pressed.
The machine continuously
fills with water and
continually drains away or
Water left in the drum or
Stuck on wash
· The top of the drain hose is too low – It must be fitted at a height between
65 and 100 cm from the floor (see “Installation”).
· The drain hose is connected incorrectly to the sink trap allowing water to run
into the machine, the drain hose must be positioned higher than the bottom
of the sink to prevent water flowing down the drain hose..
· The end of the drain hose has been pushed too far down the standpipe, the
“U” bracket should be fitted 100mm from the end of the drain hose.
· The pump filter is blocked.
· The drain hose is kinked (see “Installation”).
· New Installation – The blanking cap or spigot has not been removed if
connected under a sink.
· The drain hose or sink trap is blocked.
· Program times will vary due to water pressure, the incoming water
temperature and if the wash load goes out of balance. This will increase the
program times accordingly (see “The machine wont spin properly” next
page).
· The feet have not been adjusted, enabling the machine to rock.
The machine vibrates a lot
during the spin cycle
22
· New Installation – Either the Transit Bolts including the plastic spacer, or the
Polystyrene Packaging have not been removed when installing the machine.
· The machine is trapped between cabinets and/or walls.
· The load is in a slight out of balance condition and machine is spinning, but
at a lower speed.
· After switching on the machine a cycle other than M-Smart wash cycle was
activated. Switch the machine off and press the One Touch button.
Troubleshooting
Problem
Possible cause / solutions
The machine wont spin
properly
· Out of Balance detected when attempting to go into a spin cycle – If this
happens the machine will continue to try to repeat the distribution of the
load required before the machine will go into higher spin speeds – This will
increase the program time accordingly. This is a safety feature to prevent
damage. Out of Balance can be caused by washing a single heavy item (eg
down, quilt, etc). – Try the programme again using a different load.
The machine leaks from
the dispenser
The machine leaks (other
than dispenser)
· The machine requires a service wash. Run a “Drum Clean” wash cycle with
detergent and no laundry.
· The water level is correct if it can be seen at the bottom of the door
General
· Your washing machine contains sensors that monitor progress during the
wash cycle (eg: Water level, Temperature, Out of balance loads, Wash
time/progress). Normally, if your machine successfully completes the cycle,
there is unlikely to be anything wrong!
· The dispenser drawer is blocked with detergent and requires cleaning.
· The water pressure is too high and requires turning down – turn down the
tap on the water supply pipe slightly and try again.
· The machine is tilting forwards – It must be level when in its final position.
· The inlet hose is loose, check both the cabinet and tap ends .
· The inlet hose is tight but still leaks, if so replace the rubber washers, or the
inlet hose is missing the rubber washer.
· The drain hose is not fixed in properly.
The machine smells
The machine door cannot
be opened.
The water level is too low
when the machine is
washing
There is too much foam
· The door will not open until the door lock indicator light goes out shortly
after the program has finished.
· If there is no power to the machine you need to perform the manual
unlocking procedure.
· The detergent is not suitable for machine washing (it should display the text
“for washing machines” or “hand and machine wash” or the like).
· Too much detergent was used – less detergent is required in soft water.
23
Fault codes
Fault type
Possible cause / solutions
E02
No inlet water
· Check whether the faucet is turned on? Whether the water
supply is cut off? Whether the water inlet hose and the filter of
the water inlet valve are blocked? and whether the water inlet
hose of the washing machine is frozen? In such case, please
contact the service center for repair.
E03
Abnormal water
drainage
U4
Door lock malfunction
· Close the door again, and then press the “START/PAUSE” button
to restart the program. If the fault still exists, please contact the
service center for repair.
The temperature in the
drum is high
Other faults
In case of the following faults, the fault state will be detected by the microcomputer system, with the buzzer
sounds issued and the following fault codes display:
· Clean the pump filter.
· Check whether the drain hose is bent, twisted or blocked? If the
fault still exists, please contact the service center for repair.
· Press the “START/PAUSE” button to suspend the washing
H
machine operation and wait for several minutes. When the
temperature in the drum drops to a safe range and the fault
code on the display is removed, press the “START/PAUSE”
button to continue the rest of the program..
EXX
Note: Be sure to check the fault cause and eliminate the fault before pressing the START/PAUSE button again. If
the fault code is removed, the washing machine will continue to run, and if the fault code still exists, please
unplug the power cord and call our customer service center for help as soon as possible.
Remember, you will be charged for a service call for problems caused by incorrect installation, as indicated on
pages 6 to 9.
Not emptying contents from pockets may cause pump or drain hose blockages, or may damage the machine.
Do not wash items which do not have a wash label, or wash items that are not intended as machine
washable
· Turn the washing cycle selector knob to the “OFF” position to
turn off the power supply, unplug the power cord, and contact
the service center for repair as soon as possible..
For any enquiries, please call the CHiQ Cusotmer care on: 1300 796 688.
24
Customer Service
1300 796 688
www.chiq.com.au
c
Changhong Electric (Australia) P/L all rights reserved.
Loading...