INSTRUCTION MANUAL FOR USE OF
BABY STROLLER “TRIA 3 in 1”
THE SAFETY OF PRODUCTS AND THE MATERIALS
USED FOR THEIR PRODUCTION IS GUARANTEED AND CERTIFIED
IN TEST LABORATORIES ACCORDING TO EN STANDARDS.
PLEASE READ CAREFULLY THIS INSTRUCTION MANUAL AND
KEEP IT IN A SAFE PLACE FOR FUTURE REFERENCE! IT CONTAINS IMPORTANT INFORMATION, INSTRUCTIONS AND RECOMMENDATIONS FOR THE STROLLER AND ITS SAFE USAGE
1
This set contains:
• Baby stroller, suitable for a child aged 6 months plus and weight up to 15 kg.
• Carry cot, suitable for a newborn baby to 6 months, weighing up to 9 kg, who cannot sit
unaided, roll over or push up on its elbows and knees.
• Car seat, weight group 0+, suitable for newborn babies and children weighing up to 13 kg.
The seat unit, carry cot and car seat can be installed in both directions, allowing face to
face and forward facing mode. The seat is equipped with a 5-point harness for the safety of the
child. The seat and canopy positions may be adjusted. The carrycot has a handle for carrying.
The car seat must be installed in a rear facing position in the vehicle. The car seat has a Y
safety belts.
The stroller and the carry cot are manufactured according to the requirements of the
Product Safety Directive 2001/95/EU of the European Parliament and The Council and with
European standard EN 1888 "Child care articles. Wheeled child conveyances. Safety requirements and test methods” and the regulations of national legislation and with EN 1466 - Child
care articles. Carry cots and stands. Safety requirements and test methods, the car seat is in
compliance with the requirements of Regulation 44 of the United Nations Economic Commission for Europe concerning the safe transportation of children.
ATTENTION! Your child will be protected to maximum extent only if you follow the guide-
lines and recommendations in this instruction manual! Pay special attention to the warnings
and secure all necessary safety precautions in order to prevent the risk of injury or impairment
and guarantee your child’s safety! You are solely responsible for the safety of your child, if you
don't follow exactly the instructions and safety recommendations in this manual! Make sure
that everybody who uses this stroller has read and understood this manual!
NOTE: For your convenience, the instruction manual of the car seat is supplied with the car
seat package.
1. Never leave your child unattended!
2. The seat of this stroller is not suitable for children under 6 months of age!
3. The seat unit must be used by children that are older than 6 months and can stay
in sitting position unaided!
4. The stroller is suitable for children weighing up to 15 kg, the car seat is for
children with weight up to 13 kg, and the carry cot is intended for babies weighing up to
9 kg, that cannot sit unaided, roll over or push up itself on elbows or knees. Not following these requirements can cause overloading, tension and instability, and may make
the construction unstable, and bring the stroller to tip-over and injure your child
seriously!
5. This stroller , car seat and the carry cot are intended for use for one child at a time!
It is dangerous to carry two or more children at a time in the stroller, car seat or carry
cot!
6. Always mount the carry cot in a face to face mode.
7. Use the products only for the purpose they were made.
8. Initial assembly, folding and unfolding to be done only by an adult!
9. Before each use check the good working order of the stroller, car seat and carry
cot and the stability of the assembly of the parts (seat unit, canopy, footrest, backrest,
bumper and handle) in the desired position! Discontinue usage if you find worn out or
loose joints, damaged or missing parts! There is big risk of injury of the child!
10. The maximum load for the storage basket is 3kg. The baggage carried must be
evenly distributed in the basket. Do not overload the storage basket! Do not use storage
basket as a child carrier!
11. Always attach the canopy to the backrest of the seat to prevent your baby from
accidentally slipping off or injury.
12. To avoid serious injury from falling or sliding out, always use the safety
harnesses. Always use the belts when your child is able to stay sitting unattended and
when it starts lifting itself up with hands and knees. Adjust the harnesses to snug fit
around your child, so they will not change their length and not be twisted. Periodically
check if they are firmly attached to the stroller construction and if they lock safely! The
harnesses must not be worn out or torn; the plastic buckles must be undamaged and
provide safe joining.
13. Before each use check the good working order of the brakes. Always engage the
brakes when the stroller has stopped and is not moving, especially on sloped surfaces
and when placing or taking your child out of it!
14. Make sure the stroller is fully unfolded and all locking mechanisms are engaged
before placing the child in the stroller in order to prevent sudden folding of the stroller.
15. When the child is sitting, its head must be below the upper end of the backrest.
16. Fold and unfold carefully in order to avoid finger entrapment! Make sure the child
is in safe distance away from the stroller when you make adjustments, when you fold or
unfold the stroller.
17. Never lift, fold, adjust or repair the stroller while the child is in it!
18. Keep the child away from any separable or moving parts.
19. Do not adjust the backrest while the child is in the stroller! The position of the
backrest of the seat should be adjusted only by adult.
20. Do not leave bags or other items in the stroller with the child or on the canopy!
Every load attached to the handle, bumper, and backrest or on the side of the stroller
will affect its stability. Do not overload the stroller! If you do, it may tip over and injure
the child.
2
SAFETY REQUIREMENTS AND WARNINGS!
3
21. Do not place items with long strings around your child's neck and do not attach
additional strings to toys to avoid strangulation!
22. Do not place an additional mattress in the cot!
23. Extra pads or pillows placed on the seat will impede the proper use of the safety
harnesses and will reduce the safety and stability of the child in the stroller!!
24. Always keep the front bumper locked while the child is in the stroller! Do not lift
the stroller by the front bumper, it is dangerous for the child!
25. Do not let your child stand in the stroller, climb or hang on it!
26. Do not allow your child to play with the stroller! It is dangerous to let children or
animals play or run close to or beneath the stroller!
27. The stroller should be used only at a walking speed! Do not use while jogging,
skating, running or performing other sport activity!
28. Do not use near pools, hot surfaces or other hazardous areas!
29. The carry cot must be placed only on even dry surface, at a safe distance from
stairs and escalators. Take extra care when going up or down a pavement or step!
30. Never use stroller on stairs or escalators! You may suddenly lose control of the
stroller or your child may fall and injure itself!
31. Do not make any changes or modifications to the stroller's construction,
because they may endanger your child’s safety! Only use spare parts or other components, which are recommended or supplied by the producer! In the contrary case the
producer is not responsible for the product’s safety. In case of problems contact the
dealer or an authorized repair service for advice and/or repair!
32. When the stroller is folded, keep it in a safe place away from children! Otherwise
the child can push the stroller down and hurt itself.
33. The plastic packaging of the product must be kept out of the reach of babies and
children at the time of and after unpacking. In this way you will avoid the risk of strangulation and/or asphyxiation (choking) caused by entanglement of the packaging around
the child or external blocking of the respiratory tract through the child's nose or mouth!
This stroller is supplied partially assembled. In order to complete the assembly, you don’t
need any tools.
Follow exactly the instructions given and check the pictures. Please, note that in most
cases after the completion of an operation you will hear a clicking sound.
IMPORTANT! After each operation, make sure that you have followed the instructions
correctly and the fixing is stable.
ATTENTION! Do not allow children younger than 3 years near the stroller during the
assembly or disassembly, in order to prevent the risk of injury or swallowing of small parts!
Keep your hands from finger entrapment, especially during folding or unfolding the stroller.
1. Handle grip
2. Canopy frame
3. Main connector
4. Front leg tube
5. Footrest
6. Front wheel
7. Wheel cap
8. Rear leg tube
9. Rear wheel
10. Break pedal (red)
11. Cross bars
12. Canopy holder
13. Handle tube
14. Folding levers
15. Seat unit connectors
16. Break release pedal (green)
17. Seat unit adjustment button
18. Seat unit Quick release button
19. Front bumper
20. Supporting tube
21. Link break wire
22. Folding mechanisms release button
23. Directional lock
24. Front wheel socket
25. Top part of the seat
26. Down part of the sear
27. Fixing hook
4
ASSEMBLY AND FUNCTIONS OF THE STROLLER
PARTS LIST
Place the folded frame of the stroller on a flat surface (fig.1-1). Release the fixing hook.
Grab the handle of the stroller and pull it up (fig.1-2), until the stroller is fully unfolded and
you hear a click (fig.1-3).
ATTENTION! Check if the mechanisms are well engaged.
Insert each front wheel in the front wheel sockets as shown in fig.2, until you hear a click.
Check if the wheel is well installed by trying to pull it out.
When you press button A, shown in fig.3, the wheel will disassemble from the tube.
ATTENTION! The good working order of the buttons is very important for the locking of
front wheels and for the safe use of this stroller.
5
UNFOLDING THE STROLLER
FRONT WHEELS
fig. 2
fig. 3
fig. 1
6
SWIVEL AND STRAIGHT MOTION OF THE FRONT WHEELS
REAR WHEELS
The front wheels can swivel (at 360°) or move straight.
ATTNETION! You must position the wheels in the position shown in fig.3, before fixing
them in swivel or straight motion.
Праволинейно Straight motion of the front wheels
The front wheels will move only straight, when you press down the lever В on each front
wheel (fig.3).
Swivel motion of the front wheels
Lift the lever B on each front wheel in order to activate the swivel function.
ATTENTION! When you move the stroller on uneven surfaces, it is better to fix the wheeels
in straight motion! For even surfaces it is recommended to use the swivel function. If you follow
these reccomendations, the wheels will move easyly and will wear out less.
Insert the rear wheel in the rear axel until you hear a click (fig.4). Make sure the wheels are
well fixed.
The parking device is located at the rear wheels.
Press down the red break pedal in order to engage the parking device (fig.5-1). Make sure
that the parking system is engaged. When you push the stroller gently it should remain still.
Press down the green break pedal to release the parking device (fig.5-2).
ATTENTION! When the stroller is not in motion, always use the parking device! Never
leave the stroller on a slope, even if the parking device is engaged if there is a baby in it!
ATTENTION! Please check whether both wheels are assembled property before using the
stroller.
fig. 4 fig. 5
7
CANOPY
FRONT BUMPER
To assemble the canopy, place its two brackets to the frame tube, as shown in fig.6. To
remove the canopy, pull it out.
ATTENTION! Always use the velcro at the back section of canopy and attach it to the seat.
The canopy can be opened or closed by pulling or pushing it by hand.
Insert the two ends of front bumper in the armrests holes, as shown in fig.7, until you hear
a click. To remove the bumper, press the buttons located at both sides of bumper and pull out
(fig.8).
ATTENTION! Always use the safety belts in combination with the front bumper.
fig. 6
fig. 7 fig. 8
8
SAFETY BELTS
SEAT UNIT
ATTENTION! Always use the safety belts when the baby is inside the stroller.
The stroller is equipped with a 5-point harness. Join the loose ends of the shoulder and
waist straps, as shown in Fig.9. Insert them in the central buckle until you hear a click (fig.10).
Adjust the length of the belts according to the baby’s growth. In order to unfasten the
harness, press the central buckle button as shown in Fig.10- and pull out the belts (fig.10-2).
Place the two plastic adaptors of the seat unit in the corresponding holes in the stroller’s
frame. If the seat is well fixed, you will hear a click. The seat can be mounted in two directions,
allowing face to face and forward facing mode (fig.11).
ATTENTION! Make sure the seat is well fixed and is stable before each use.
The seat can be adjusted in 3 positions. In order to adjust the backrest, press the two
buttons at the two sides of the seat (fig.12).
To deinstall the seat unit form the frame, press simultaniously the two buttons for quick
release of the seat as shown in fig.13 and pull out the seat.
fig. 9 fig. 10
fig. 11
fig. 12 fig. 13
9
PLACING OF THE FOOTCOVER
FOLDING OF STROLLER
Place part А of the footcover (fig.14) on the footcover (fig.15-1).
Thread the footcover through the front bumper (fig.15-2) and fasten at the front (fig.15-3).
ATTENTION! Make sure that the child is at a safe distance from the stroller during folding
and unfolding.
The stroller can be folded with and without the seat on the frame.
ATTENTION! If you want to fold the stroller with the seat installed, it must be in forward
facing mode and the backrest must be in most upright position.
When you fold the stroller with the seat installed, it must be in forward facing mode and the
backrest must be in most upright position.
To complete the folding, please follow these steps:
- Apply the parking device at rear wheels
- Remove the footcover..
- Position the seat in forward facing mode (fig.16А).
- Put the backrest in most upright position.
- Stay at the side of the handle.
- Press and hold the button for releasing (fig.16В-1) at the right side of the handle and
simultaneously pull the folding lever (fig.16В-2).
- Press the handle to the front (fig.16C), until the stroller is fully folded (fig.16D).
- Fix the stroller with the fixing hook.
fig. 14 fig. 15
fig. 16
10
CARRY COT
UNFOLDING OF THE CARRY COT
1. Unfold the two U shaped metal parts located at the inside of the carry cot , under the
mattress, to the sides of carry cot, until they are fixed in the holes (fig.17-1).
2. Lift the handle until you hear a click (fig.17-2).
3. Attach the fabric of the canopy to the fabric part of the carry cot by the velcro (fig.17-3).
4. Close the snap buttons at two sides of the canopy (fig.17-4).
1. Place the footcover on the carry cot and fasten the buttons on the outer side of the carry
cot (fig.18-1).
2. Align the other buttons and fasten them at the inner side of the carry cot as shown in
fig.18-2.
3. The carry cot is ready for use (fig.18-3).
PLACING THE FOOTCOVER ON THE CARRY COT
fig. 17
fig. 18
11
INSTALLING OF THE CARRY COT ON THE STROLLER FRAME
REMOVING OF THE CARRY COT
ATTENTION! ALWAYS INSTALL THE CARRY COT IN A FACE TO FACE MODE FOR A
NEWBORN BABY (fig.19А)!
To install the carry cot on the frame, position it in a face to face mode, align the carry cot
adaptors with the corresponding holes on the frame and press down until you hear a click
(fig.19-В).
ATTENTION! Make sure that the carry is well fixed before each use.
To remove the carry cot form the frame, press simultaniously the two buttons for quick
release of the cot as shown in fig.20 and pull out the cot.
fig. 19
fig. 20
A B
12
FOLDING THE CARRY COT
CAR SEAT
INSTALLING OF THE CAR SEAT ON THE STROLLER FRAME
To save space, the carry cot may be folded for storage.
ATTENTION! It is dangerous to fold the carry cot if it is installed on the frame and there is
a baby in it!
Remove the carry cot from the frame and follow the steps:
1. Press simultaneously the two buttons of the carry cot (fig.21-А) and close the canopy
(fig.21-В).
2. Remove the footcover and the mattress.
3. Lift the two U shaped parts, take them out of the holes and close them to the center of
the carry cot (fig.22).
4. The cot is now folded (fig.23).
fig. 21 fig. 22 fig. 23
fig. 24
13
DEINSTALL OF THE CAR SEAT FROM STROLLER FRAME
ATTENTION! ALWAYS INSTALL THE CAR SEAT IN A FACE TO FACE MODE FOR A
NEWBORN BABY!
To install the car seat:
1. Stay at the side of the handle and place the adaptors with markings L and R (fig.24-1)
on the stroller frame. The adaptor with marking L must be placed at the left side, and the
adaptor with letter R- at the right (fig.24-2). The adaptors are fixed when you hear a click
(fig.24-3).
2. You must position the car seat in a face to face mode.
3. Align the ends of the car seat with the adaptors (L/R) and press the car seat down, until
you hear a click (fig.25). Make sure the car seat is well fixed.
1. Press the quick release levers ”А” at both sides of the car seat (fig.26).
2. Grab the car seat by the handle and pull out until it detaches from the adaptors.
3. Remove the adaptors from the stroller frame by pressing the release buttons shown in
fig.27 and pull them out.
NOTE: All instructions for use and maintenance of the car seat are in a separate manual,
supplied with the car seat package.
fig. 25
fig. 26 fig. 27
14
CARE AND MAINTENANCE GUIDELINES
1. Regularly check all locking mechanisms, brakes, safety harnesses and buckles, joints
and fixing mechanisms to make sure that they function properly and are not damaged or worn
out.
2. Should you find loose, torn or damaged parts, they need to be repaired or replaced.
3. Brakes and wheels wear out faster than other parts. Replace them when necessary.
4. Regularly oil the driving mechanisms. Renew the rivets when necessary. It is recommendable to use silicone oil or silicone spray for oiling.
5. Dirty metal or plastic parts impede the normal function of your stroller. Clean your stroller
regularly and after that oil it.
6. Clean the fabrics, plastic parts and metal parts of the stroller with damp cotton cloth or
sponge and water or mild soap. The fabric (except the canopy) can be removed and
handwashed at 30°С. Do not machine wash. The fabric can be easily removed by means of
zippers and buttons.
7. Do not use abrasive, bleach, ammonia, spirit or other aggressive detergents.
8. Аfter cleaning always leave the stroller to fully dry and after that use it or store it.
9. Always store your stroller indoors. The effect of the environment – sea air, road covered
with salt, acid rains, etc., as well as storing in the open air lead to corrosion.
10. Do not store your stroller in wet environment. In case you stroller has been stored in wet
environment, you must first unfold it, wipe it with a dry cloth and leave it to dry out. Mold may
appear on your stroller if it was stored wet.
11. Heavy sun exposure makes the plastic parts wear out faster and the fabrics fade out.
12. Do not put other items on the stroller when you store it regardless of whether it is folded
or not, because you may damage it.
13. In case of problems with the normal use of the stroller, please contact the authorized
repair service for advice or repair.
14. A full check from the technician is recommended if you have stored the stroller for a
long period of time or want to use it for another child.
Fabric content:
Outer: 100% polyester
Filling: 100% polyester
KKTRS130xxx
1 Goliamokonarsko shosse, Plovdiv, BULGARIA
www.chipolino.com
Loading...