Page 1
IMPORTANT! KEEP THIS MANUAL FOR FUTURE REFERENCE
INSTRUCTION MANUAL
FOR USE OF CHILD RESTRAINT SYSTEM
„TECHNO”
This child restraint system is designed and manufactured
in compliance with the requirements of Regulation 44 of the United Nations
Economic Commission for Europe concerning the safe transportation of children, the provisions of the Product safety Directive 2001/95/EU of the European Parliament and The Council as well as the Consumer Protection Law of
Bulgarian Legislation.
Page 2
NOTICE
For universal child restraint , groups 0+, I , II and III
1. This is a “UNIVERSAL” CHILD RESTRAINT. It is approved to Regulation No 44, 04 series of
amendments, for general use in vehicles and it will t most, but not all, car seats.
2. A correct t is likely if the vehicle manufacturer has declared in the vehicle handbook that the
vehicle is capable of accepting a “universal” child restraint for these age groups.
3. This child restraint has been classied as “universal” under more stringent conditions than
those which applied to earlier designs which do not carry this notice.
If in doubt, consult either the child restraint manufacturer or the retailer.
N O T I C E
for semi-universal child restraint, groups 0+ and I
1. This is an ISOFIX CHILD RESTRAINT. It is approved to Regulation No 44, 04 series of amend-
ments, for general use in vehicles tted with ISOFIX anchorages systems.
2. It will t vehicles with positions approved as ISOFIX positions (as detailed in the vehicle handbook), depending on the category of the child seat and of the xture.
The mass group and the ISOFIX size class for which this device is intended is GROUP 0+ (0-13
kg), ISOFIX class D и GROUP I (9-18kg), ISOFIX class D.
NOTICE
for semi-universal child restraintq groups 0+, I , II и III
This child restraint is classied Semi-universal use and is suitable for xing into the seat positions
of the following car:
Seat positions in other cars may also be suitable to accept this child restraint. If in doubt, consult
either the child restraint manufacturer or the retailer.
NEVER INSTALL THE CAR SEAT IN FORWARD FACING POSTION BEFORE THE CHILD’S
WEIGHT EXCEEDS 9 kg!
CAR CAR REAR
Refer to
Vehicle list
Outer Centre
Yes Yes No
DO NOT FORGET THAT NO RESTRAINT SYSTEM CAN PROVIDE AB-
SOLUTE PROTECTION IN CASE OF A CRASH OR ROAD ACCIDENT!
DRIVE WITH CARE WHEN THERE IS A CHILD IN YOUR VEHICLE!
IN ORDER TO ENSURE THE SAFETY OF YOUR CHILD, FOLLOW
EXACTLY THE INSTRUCTIONS AND SAFETY RECOMMENDATIONS IN
THIS MANUAL!
MISUSE OF THE CAR SEAT WILL CONTRIBUTE TO REDUCING ITS SECURITY
AND SAFETY FEATURES! FAILURE OF THE GUIDELINES OF THIS
INSTRUCTION INCREASES THE
RISK OF SERIOUS INJURY OR DEATH!
CAUTION!
1
Page 3
It is prohibited to place the car seat in a vehicle
with a two-point seat belt.
Place the cars seat ONLY in a vehicle with a
3-point seat safety belt .
PLACE OF THE CAR SEAT IN THE VEHICLE
CAUTION! The child restraint is suitable for
use in vehicles, equipped with approved LAP/3POINT/STATIC/WITH RETRACTOR SAFETY
BELTS in compliance with ECE R16.
Do not place the restraint system on a vehicle seat equipped with air bag! This may
result in death or serious injury!
Review the instructions of the vehicle for information about airbags and conditions of transportation of children.
Do not install the car seat on that seat
in the vehicle.
“REARWARD FACING” installation
of the car seat is not recommended on a seat
equipped with air bag, which cannot be deactivated. Only use with 3-point seat belt and
airbag off or position of the vehicle seat as far
back as possible so the car seat to be away
from the air bag.
You can install car seat only if the vehicle seat is equipped with 3-point safety belt.
The rear outside seats are the most safety position of the vehicle for child under 12 years old. Install
the car seat on vehicle seat “ FORWARD FACING”. Do not install on side facing or rearward facing
vehicle seat. If any doubt about installation, please check your vehicle user manual, or contact the
vehicle supplier.
2
Page 4
Child restraint TECHNO
Group Method of installation in the vehicle Approved type of system
0+ and I
“Rearward
facing”
I
“Forward
facing”
II and III 3-point safety vehicle belt Universal
II and III 3-point safety vehicle belt + additional xing Semi-universal
3-point safety vehicle belt Universal
ISOFIX attachment+ top tether Semi-universal ISOFIX
3-point safety vehicle belt Universal
3
Page 5
CAUTION! NEVER LEAVE YOUR CHILD UNATTENDED!
CAUTION! DO NOT USE ANCHOR POINTS OTHER THAN THE ONES DESCRIBED IN THIS
MANUAL AND MARKED ON THE RESTRAINT SYSTEM.
CAUTION! NEVER INSTALL THE CHILD RESTRAINT IN THE DIRECTION OF VEHICLE MOVE
MENT AND FACING FORWARD BEFORE THE CHILD WEIGHT REACHES 9kg!
CAUTION! THE CAR SEAT SAFETY MUST BE PROPERLY ADJUSTED ACCORDING TO CHILD’S
HEIGHT, NOT TWISTED AND SNUG WELL AGAINST BABY’S BODY.
CAUTION! THIS CHILD RESTRAINT SHOULD NOT BE MODIFIED OR ADAPTED WITH NEW
FITTINGS, WITHOUT PREVIOUS AUTHORIZATION BY THE COMPETENT AUTHORITY.
CAUTION! KEEP AWAY FROM FIRE!
Installation in the vehicle and securing the child in the car seat to be done only by adult!
The hard parts and the parts of the child restraint made of plastic should be located and installed
so that when the vehicle is in normal use, they can not be trapped by a sliding seat or in a door of
the vehicle.
Do not allow the safety belts of the car seat and the vehicle to be twisted, frayed or torn, latches and
locks (buckles) must be always in good order and rmly xed.
If you nd uncertainty or defect in the structure, latches, straps or locking mechanisms of the car
seat or ISOFIX attachments , discontinue usage until removal of the damaged parts and replace
ment with new ones.
After a violent impact the car seat and belts may be damaged. therefore, it is recommended to re
place the car seat with new one.
Never use a second hand child restraint. it may have suffered structural damage, which may make
the child restraint extremely dangerous.
Do not use this car seat without its seat cover and do not replace it with a new one, unless supplied
by the manufacturer. The fabric parts are integral parts of the restraint system and its safety
features!
Always make sure that you are not carrying any unsecured objects, especially on the back shelf,
which, in case of an accident, may injure the car’s occupants
Do not put additional pads except the ones supplied from the manufacturer! Placing additional pads
may obscure the safety of your child.
Do not use spare parts and other components not supplied by the manufacturer. The manufacturer
assumes no responsibility for safety in the event that are used spare parts other than original.
It is recommended to cover the car seat if the vehicle is parked under strong sun shine – extreme
sun exposure will make the plastic to deteriorate and the fabric to fade. Please, check that the child
restraint has not become too hot before placing your child seat.
The child car seat does not replace the child's cot or bed. When a child needs a sleep, you have to
place him in a suitable baby stroller, baby crib or bed.
Do not attach objects with long cords or strings on the car seat in order to avoid danger of
suffocation!
Never place a child seat on beds, couches or similar soft surfaces!
Do not allow children to play with the product!
Do not remove stickers and warnings – they contain important information!
The packaging of the product must be kept out of the reach of children at the time of and after
unpacking in order to avoid the risk of strangulation!
4
Page 6
PRODUCT FEATURES
Child restraint restraint while traveling in a vehicle designed for children weighing from
0 to 36 kg, classied in weight groups:
• 0+ (0-13 kg): universal and semi-universal integral ISOFIX child restraint, ISOFIX class D.
The restraint system is installed in direction opposite to the direction of the vehicle and the child is
"rearward facing";
• I (9-18kg): universal and semi-universal integral ISOFIX child restraint, ISOFIX class D . The re
straint system is installed in direction opposite to the direction of the vehicle and the child is
"rearward facing" or in the direction of the vehicle and the child is “facing forward”;
• II (15-25kg): universal and semi-universal non-integral system for securing children. The restraint
system is installed in the direction of the vehicle and the child is “facing forward”;
• III (22-36kg): universal and semi-universal non-integral system for securing children. The restraint
system is installed in the direction of the vehicle and the child is “facing forward”;
ISOFIX attachments to vehicle (for groups 0+ and I);
Possibility for additional xing of the car seat groups II and III with ISOFIX connectors;
Top tether (only for groups 0+ and I, “REARWARD FACING“ car seat);
The restraint rotates 3600 on the base;
Backrest recline;
Head rest height adjustment;
5-point safety harness on the restraint;
Additional soft pads;
MAIN PARTS DIAGRAM
The pulling ring
Headrest
The belt guider in
Group II/III
Baby cushion
Shoulder pads
5 points harness
system & buckle
Crotch pad
Pull rod for
reclining
switch-lock
handle
Center adjuster
belt
Top tether
adjuster
Top tether
Hook
ISOFIX
Belt guider in
Group II/III
ISOFIX
release button
INSTRUCTIONS FOR USE
IMPORTANT!
• Follow exactly the instructions and sequence of installation steps and use of the product described
in the text and gures of this manual.
• Check the security of xing after each operation!
• ALWAYS CHECK THE SECURITY OF FIXING OF THE SAFETY BELTS!
• After each installation make sure that the seat belts are not twisted and are in the correct position
5
Page 7
INSTALLATION OF CAR SEAT GROUP 0+ AND GROUP I
For groups 0+ and I you can install the car seat on vehicle seat with 3-point safety belt of the vehicle or
with ISOFIX connectors:
“REARWARD FACING” group 0+ and I
ISOFIX+top tether
“FORWARD FACING” group I
3- point safety belt of the vehicle
At ISOFIX attachment, there are three anchor points - two ISOFIX connectors and top tether.
3- point safety belt of the vehicle
3- point safety belt of the vehicle
For groups II and III the car seat is installed with ISOFIX + 3-point safety belt of the vehicle or only with
3 – point safety belt of the vehicle. DO NOT USE THE TOP TETHER!
6
Page 8
INSTALLATION OF THE CAR SEAT WITH ISOFIX CONNECTORS
click
ISO FIX
ISOFIX attachment points
in the vehicle
push
push
push
shake
IMPORTANT! When the ISOFIX connectors are xed the indicators must show „green color” (4)! That
is conrmation for correct xing of the car seat.
CAUTION! After installation make sure that the car seat is rmly and securely secured to the vehicle
seat (5 and 6). If the seat shakes or the ISOFIX connectors are removed, repeat steps 1 to 4 to reinstall
the seat.
INSTALLATION OF THE CAR SEAT WITH ISOFIX AND TOP TETHER
“REARWARD FACING”
car seat
Install the ISOFIX connectors
tighten
upper anchor point
shake the car seat
Note: The upper anchor point is xed device on the trunk or the oor of the vehicle.
IMPORTANT! Tighten the belt of the top tether, until the indicator of top tether adjuster show „green
color” (3) If the indicator does not show green, reinstall.
CAUTION! After installation make sure the car seat is rmly and securely secured (4).
7
Page 9
INSTALLATION OF THE CAR SEAT groups 0+ and I
WITH 3-POINT SAFETY BELT OF THE VEHICLE
( “REARWARD FACING” )
CAUTION! Place the car seat in the vehicle “REARWARD FACING”! (1)
diagonal belt
pull
“REARWARD FACING”
car seat
Put it in a lying position - position “R”
remove the soft
pad
lap belt
WARNING!
MAKE SURE THE VEHICLE BELTS
ARE NOT TWISTED AND ARE IN
CORRECT POSITION!
vehicle belt
click
IMPORTANT! Make sure the vehicle belts are tightened and the car seat is well xed to the vehicle
seat.
8
Page 10
INSTALLATION OF THE CAR SEAT group I
WITH 3-POINT SAFETY BELT OF THE VEHICLE
( “FORWARD FACING )
CAUTION! Place the car seat in the vehicle “FORWARD FACING”! (1)
“FORWARD FACING”
car seat
vehicle belt
tighten the belts
diagonal belt
remove the soft pad
diagonal belt
lap belt
WARNING!
MAKE SURE THE VEHICLE BELTS
ARE NOT TWISTED AND ARE IN
CORRECT POSITION!
click
IMPORTANT! Make sure the vehicle belts are tightened and the car seat is well xed to the vehicle
seat.
9
Page 11
press
pull
5-POINT HARNESS OF THE CAR SEAT.
USE FOR GROUPS 0+ and I
IMPORTANT! Connect the
two metal tongues together
DO NOT INSERT THE METAL
TONGUES ONE BY ONE
Unfastening
“click”
pull the belt
press
After placing the child in the car seat and fastening the belt, pull the adjusting strap to secure the belt
(6). The seat belts should be adjusted according to the body and size of the child , snug well against
baby’s body and not loosened. The recommended distance between the belts and the body of the child
should be about 3cm (or two ngers).
INSTALLATION OF THE CAR SEAT GROUP II AND GROUP III
CAUTION! IN GROUP II AND III, THE SEAT IS FITTED TO THE VEHICLE SEAT WITH THE 3-POINT
BELT OF THE VEHICLE (DIAGONAL AND LAP). ISOFIX MOUNTING IS OPTIONAL AND CAN BE
USED FOR ADDITIONAL ATTACHEMENT OF THE CAR SEAT TO THE VEHICLE SEAT!
CAUTION! When using ISOFIX installation with combination with 3-point safety belt of the vehicle, DO
NOT PLACE THE TOP TETHER!
CAUTION! Only use position 1 for the seat recline!
IMPORTANT! The lap belt should cover the pelvis of the child, not the waist!
10
Page 12
“FORWARD FACING”
car seat
Place the seat to pos.1
diagonal belt
lap belt
ISO FIT
WARNING!
NOT TWISTED AND ARE IN
CORRECT POSITION!
“click”
lap belt
diagonal belt
MAKE SURE THE VEHICLE BELTS ARE
UNLOCKING OF ISOFIX CONNECTORS AND TOP TETHER
1
press
press
2
pull the button
back
3-release the ISOFIX
connectors
CAUTION! Do not unlock or remove parts of the ISOFIX system applying strength! If the ISOFIX system
is not unlocked, please repeat the steps shown in the gure
loosen
release the hook
Top tether
11
Page 13
ADJUSTING THE RECLINE OF THE CAR SEAT
Pull rod for reclining
positions for car seat “FORWARD FACING”
Pull the rod and move
positions for car seat
“REARWARD FACING”
TIGHTENING AND LOOSENING OF 5-POINT HARNESS OF THE CAR SEAT
The recommended distance between the belts and the body of the child should be about 3cm (or two
ngers).
press
button for adjusting
LOOSENING TIGHTENING
pull
Press the button for adjustment with one hand
and with the other pull the shoulder belts.
Pull the adjustment strap and tighten, holding
the shoulder straps with the other hand. Keep
the recommended distance of about 3mm
(two ngers) between the child’s body and the
shoulder straps!
LOOSENING
TIGHTENING
pull
CAUTION! The belts should not be twisted!
12
Page 14
ADJUSTING THE HEIGHT OF THE HEADREST
up
2
headrest
1
down
2
Groups 0+ and I
Groups I and II
IMPORTANT! Fix the headrest in suitable for your child position. Headrest should not be too high or too
low to the child’s head.
For groups 0 + and I the slot for shoulder straps should higher than the child’s shoulder!
For groups II and III the belts guide for groups II and III (of the head rest should be higher than the
child’s shoulder and the child’s head must be well protected both sides of the headrest.
Notice: Loosen the pulling ring, to x the chosen position.
ROTATION/CHANGE OF THE DIRECTION OF THE CAR SEAT
The seat of the car seat can be rotated at 360°. It can be xed in two positions – ‘FORWARD FACING”
and “REARWARD FACING”.
o
360
DO NOT USE THE CAR SEAT IF IT IS NOT
FIXED IN THE CHOSEN POSITION!
ALWAYS CHECK BEFORE DRIVING!
“REARWARD
FACING”
For groups 0+ and I
“FORWARD
For groups I, II, III
FACING”
Sideways facing
ONLY
for the convenience when
installing the car seat!
ATTENTION!
DON’T USE THIS POSI-
TION WHILE DRIVING!
rotate
1
pull
2
3
“click”
4
CAUTION! The seat is xed only in position “REARWARD FACING” or in position “FORWARD FAC-
ING”, when you hear click sound(3). Make sure the seat is xed in the chosen positon (4)!
13
Page 15
STORING THE 5-POINT HARNESS OF THE CAR SEAT FOR groups II and III
“click”
press
press
pull
REMOVAL OF THE FABRIC COVER OF THE CAR SEAT
CAUTION! Do not use the car seat without its fabric cover!
Unfasten the buckle of 5-point harness, x the headrest in the highest
position and lift the pad!
Follow the consequence of gure
from 1 to 5 below:
tighten
press
Separate the metal
buckle
Store the buckle
Remove the soft
Headrest
fabric cover
pads
14
Page 16
PLACING THE FABRIC COVER
Soft pad
fasten
For groups 0+ and I
For groups 0+ and I
CARE AND MAINTENANCE
Clean the fabrics, plastic parts and metal parts with damp cotton cloth or sponge and mild soap
Upholstery may be hand washed at 30OС using mild detergent!
Do not bleach! Do not tumble dry! Do not machine wash! Do not iron!
Do not use abrasive, bleach or other aggressive detergents.
Always after cleaning leave the car seat fully dry and after that use it or store it.
Harnesses must be cleaned with damp cloth and mild soap!
Do not wet or remove the stickers. They contain important information!
Always store your car seat indoors – on dry and clean place. Do not expose to direct environment
inuence - sun, rain, moisture and high temperature intervals.
Please, contact your authorized dealer for problems connected with the use or repair.
Fabric:
Outer: 100% polyester
Filling: 100% polyester
30°
Materials used: plastic, metal, textile
STKTH020xxx
15
Page 17
List of vehicles, suitable for xing of
semi-universal child restraint system,
model „TECHNO”
Child restraint system model „TECHNO” can be tted on the marked place in
the vehicle.
Child restraint system model „TECHNO” CANNOT be tted on the marked
place in the vehicle.
If your vehicle is not listed in this manual or it is not marked with or ,
then please refer to your vehicle’s handbook or contact the manufacturer for further
information.
Seat positions in other vehicles may also be suitable to accept the child restraint. If
in doubt, consult either the child restraint manufacturer or the retailer.
16
Page 18
1718192021
Page 19
Page 20
Page 21
Page 22
Page 23
Bulgaria, Plovdiv, Golyamokonarsko shosse Str. № 1
www.chipolino.com
Loading...