INSTRUCTION MANUAL FOR USE OF
BABY STROLLER “LUMIX”
THE SAFETY OF PRODUCTS AND THE
MATERIALS USED FOR THEIR PRODUCTION IS GUARANTEED
AND CERTIFIED IN LABORATORIES ACCORDING TO EN STANDARDS.
LUMIX
PLEASE, READ CAREFULLY THESE INSTRUCTIONS AND KEEP
THEM IN A SAFE PLACE FOR FUTURE REFERENCE! THIS
MANUAL CONTAINS IMPORTANT INFORMATION FOR THE SAFE
USE OF THIS STROLLER!
1
This stroller is suitable for use for babies aged 0+ months, weighing up to 15 kg. The
stroller is equipped with a 5-point safety harness to assure your child’s safety. The backrest, leg
rest and canopy can be adjusted according to baby’s needs. The seat unit may be mounted in
both directions – rear motion and forward facing. The handle is height adjustable.
The stroller is compatible with car seat Lumina, group 0+ for children weighing up to 13kg.
The car seat is sold separately.
This stroller has been designed and manufactured in accordance with the Product Safety
Directive 2001/95/EU of the European Parliament and the Council and to European standard
EN 1888:2003 "Child care articles. Wheeled child conveyances. Safety requirements and test
methods".
ATTENTION! Follow these instructions thoroughly! Following the instructions will ensure
the safe use of this product!
Pay special attention to the warnings and thus you will prevent possible serious injury of
your baby and guarantee its safety!
You are solely responsible for the safety of your child if you don't follow exactly the instructions and safety recommendations in this manual!
Make sure that everybody who uses this stroller has read and understood this manual!
Safety is a shared responsibility. Although this product has been manufactured according
to all safety standards and requirements, we need your help in order to keep your child safe.
1. Never leave your child unattended! Always keep child in view while in product!
2. The use for a child weighing more than 15 kg, may cause overloading and make the
construction unstable, causing the stroller to tip-over and injure your child!
3. This stroller is intended for use for one child at a time! Do not carry more than one child
at a time in the stroller!
4. Use the upright position of the seat when the child is able to sit alone without help and
push up on hands or knees.
5. The maximum load for the storage basket is 3 kg. Do not overload the storage basket!
Do not carry your baby in the storage basket!
6. Always fix the canopy to the back rest in order to avoid serious injury from falling or
sliding out!
7. Always use the safety belts in order to prevent sliding our of the stroller! After fastening
buckles, adjust belts length to snug fit around your child. Periodically check if the harness is
well attached to the stroller! The belts should not be torn or worn out, the buckles must be
without any damages in order to assure secure locking of the harness.
8. Assembly, unfolding and folding to be performed only by adults.
9. Check the stroller before each use. All parts must be well fixed and accessories must be
attached. Discontinue using your stroller if you find any damages, loosen, worn out, broken or
missing parts!
10. Always check the brakes before using the stroller! Always use brakes when the stroller
is not in motion, especially on slopes and when you take out our put in the baby in the stroller!
11. Make sure the stroller is fully unfolded and all locking mechanisms are engaged before
placing the child in the stroller!
12. Fold and unfold carefully in order to avoid finger entrapment!
13. Never lift, fold, unfold, set and repair while the child is in the stroller, because it can
suddenly fold and injure your child!
14. Keep the child away from moving parts!
SAFETY REQUIREMENTS
15. The back rest must be adjusted by an adult only! Do not adjust the back rest while the
child is in the stroller!
16. The seat/cot can be installed in two directions - mother facing (opposite motion
direction) and motion direction. Always make sure the seat is well fixed to the frame after
changing its direction.
17. To prevent a hazardous, unstable condition, never place purses, shopping bags,
parcels or accessory items other than the ones approved by the manufacturer on the handle or
canopy! Do not overload the stroller! Always balance your stroller in a way to keep it stable and
prevent the risk of tip-over!
18. Strings can cause strangulation! Do not place items with strings around your child's
neck, such as hood strings or pacifier cords.
19. When the seat is converted into a cot, do not put a mattress with width more than 20
mm. Do not place extra pads or pillows on the seat, as this may prevent the proper use of the
safety belts!
20. Always make sure that the front bumper is well attached at both ends while the child is
in the stroller! Do not lift the stroller by the front bumper, because this can lead to serious
injuries!
21. Do not allow your child to stand in the stroller or hang on it!
22. This product is not a toy; do not allow your child to use it as a toy!
23. To be used only at a walking speed! Do not use while jogging, skating, running, etc.!
24. Never use the stroller on stairs or escalators! You may suddenly lose control of the
stroller or your child may fall out! Use extra care when going up or down a step or curb!
25. In order to prevent shaking of the stroller when using on uneven surfaces , fix the front
wheels for straight motion only! The swivel function of the wheels is recommended for even
surfaces for smoother ride.
26. Do not use near pools, hot surfaces or areas that may be hazardous to a child!
27. Follow the maximum pressure of the air wheels given in this manual! Always check the
pressure before use! The pressure must not exceed 195 kPa!
28. Do not make any changes or modifications to the stroller’s construction! The safety of
this stroller is guaranteed by the producer and certified in test laboratories. Do not attempt to
repair the stroller by yourself in case of a problem. Contact the dealer or an authorized repair
service for advice and/or repair instead! The producer does not bear any responsibility for the
safety of the child in case there were used spare parts not approved by him!
29. Do not put any objects on top of the stroller, because this may damage it!
30. When the stroller is folded, keep it in a safe place out of reach of children!
31. The packaging of the product must be kept out of the reach of babies and children at
the time of and after unpacking. In this way you will avoid the risk of strangulation and/or
asphyxiation (choking) caused by entanglement of the packaging around the child or external
blocking of the respiratory tract through the child’s nose or mouth!
2
3
1. Front bumper
2. Safety buckle
3. Seat unit
4. Leg rest
5. Swivel lock
6. Handle height adjusting button
7. Folding lever
8. Canopy
9. Handle
10. Brake pedal
11. Rear wheel
12. Storage basket
13. Front wheel
PARTS LIST
button
1
2
1
2
3
4
ASSEMBLY AND FUNCTIONS
TO UNFOLD STROLLER
FRONT WHEELS
fig. 1
fig. 2 fig. 3
This stroller is supplied disassembled by the producer. You should follow the given instructions during the assembly. After the fixing you should hear a click. Always check if the connections are stable after every fixing and make sure you have followed the given instructions!
WARNING! Keep children under 3 years of age away during assembly in order to prevent
injury. Be careful during folding or unfolding the stroller in order to avoid finger entrapment!
Place the stroller frame on even surface. Release the folding latch (fig. 1-1) by pulling it out
with your hand (fig. 1-2) and stay at the side of the stroller handle. Grip the handle and lift it up
to unfold it (fig. 1-3). Make sure that the unfolded position is well fixed.
Attention! Before placing the child in the stroller, make sure all locking mechanism are
engaged and the unfolded position is well fixed.
button
Assemble
Disassemble
1
2
1
2
5
REAR WHEELS
BRAKES
fig. 4
fig. 5
To install front wheels, insert front wheel set peg into the plastic base until you hear a
“Click” – fig.2-1.
To disassemble: Press down the button on the plastic base and pull the wheel set out –
fig. 2-2.
The front wheels can move straight forward or swivel at 360°. When you press down the
latches (fig. 3), the front wheels will move only forward. If you lift the latches up, the wheels will
swivel at 360°.
ATTENTION! In order to prevent shaking of the stroller when using on uneven surfaces ,
fix the front wheels for straight motion only! The swivel function of the wheels is recommended
for even surfaces for smoother ride.
Align the cog hole with axle, push into the
axle until you hear a “click” – fig. 4-1. Make
sure that the wheel is well attached to the axle.
Repeat the same operation for the other
wheel.
To disassemble the rear wheels, press the
button, as shown in fig. 4-1 and pull out the
wheel - fig. 4-2. Repeat the same operation for
the other wheel.
The stroller is equipped with link bake
system. To activate the brake, press down the
brake pedal (fig. 5-1). To release the brake, lift
the brake pedal with your foot (fig. 5-2).
button
6
CANOPY
SEAT UNIT
FRONT BUMPER
fig. 6
Align the canopy plastic pegs with the slots
on seat sides, press tightly to insert the pegs
into the slots – fig. 6.
ATTENTION! After the canopy is mounted,
it can’t be removed.
Seat unit is reversible and can be installed
in forward or face-to-face position!
To assemble the seat unit, align seat pegs
with the holes on frame, insert into until it clicks
into place – fig. 7.
To disassemble seat unit: Press in both
buttons and pull up seat unit.
To assemble bumper bar: Align the bumper
bar pegs with holes in the front of seat unit
(fig. 8) and insert into it until you hear a “Click”.
Disassemble: Press down both buttons on
bumper bar and pull out.
ATTENTION! Do not assemble or disassemble the seat unit, while there is a child in it!
Before placing the child in seat, make sure that it is installed properly.
fig. 7
fig. 8
А B
button
button
А B
LEG REST
BACK REST
The leg rest can be adjusted in 3 positions.
To adjust leg rest: Press down both round
buttons to adjust leg rest – fig. 9.
Hold the plastic key with your fingers as
shown in fig. 10, to adjust the position in one of
the three recline positions.
Hold the keys and pull down the seat
(fig. 10A) to adjust the back rest in lying
position. To raise the back rest to sitting
position, pull up the backrest – fig. 10B.
To adjust the backrest to more reclined position, do as shown in fig. 11.
Press the button and pull the belt out in order to recline slightly the back rest (fig. 11А).
Press the button and move the adjuster up to lift the back rest (fig. 11B).
ATTENTION! Do not adjust the seat while child is in stroller. If you want to adjust the back
rest while the child is in stroller, the child must be in sitting position and not lean on the back
rest!
7
fig. 11
fig. 9
fig. 10
SAFETY HARNESS
HANDLE HEIGHT ADJUSTMENT
FOLDING OF STROLLER
To use restraint system fig. 12: To unlock
buckle, press in on center button and pull
harness out from each side.
To lock buckle, push each side of harness
back into buckle until each clicks in place.
Press down the button on handle centre to
adjust its height – fig. 13. There are 4 height
positions available. After each position you will
hear a “click”.
Stay behind the stroller. Apply the brake.
To fold the stroller pull up both folding levers and press down handle to fold the stroller. The
stroller will lock automatically into folded position Sequence of actions is shown in fig. 14.
8
fig. 12
fig. 13
fig. 14
15-1
15-2
15-3
15-4
AIR WHEELS RECOMMENDATIONS
You must check the air wheels before each use of the stroller. The proper maintenance and
pressure is important for their use.
The optimal pressure of the wheels should not exceed 195 kPa!
Pick out the tube head from the big side (fig.15-1, fig.15-2) and fix it to the other side
fig.15-3. Fix the tube by twisting and pump until you reach the optimal pressure (fig.15-4).
9
fig. 15
10
1. Insert the car seat adaptor into the receptor of the stroller. You must hear a click sound
in order to be sure that car seat adaptor and connector are secured (fig. 16).
2. Place the car seat into the car seat adaptor as shown in the figure. Please, check if the
car seat is securely locked with the car seat adaptor (fig. 17).
3. Press the two buttons on both sides in order to release the car seat and pull upwards to
remove the car seat from the car seat adaptor (fig. 18).
4. Press the lock on the car seat adaptor (1) to release the lock function and release the car
seat adaptor as shown (2). Remove both adaptors (fig. 19).
fig. 16
fig. 17
fig. 18
fig. 19
INSTRUCTION FOR INSTALL OF CAR SEAT “LUMINA”
ON STROLLER “LUMIX”
11
CARE AND MAINTENANCE
1. Periodically check all locking mechanisms, brakes, belts and buckles, joints and fixing
mechanisms, as well as wheels to make sure that they function properly and are not damaged
or worn out.
2. Should you find any damaged parts, discontinue the use until the problem is fixed!
3. Please, note that brakes and wheels wear out faster than other parts. Replace them
when necessary.
4. If you find any loose connections, worn out, broken or missing parts, they should be
repaired or changed.
5. If you find damage or if any function doesn’t operate well, discontinue the usage of the
stroller.
6. The maintenance of the wheels will prolong their life. Check the wheels before each use
for cuttings or other damages. The maximum pressure must be 195 kPa.
7. Regularly oil the joints, re-rivet when necessary. Regular oiling of the moving parts will
prolong the use of your stroller and will make folding and unfolding easier. Tip: Use silicone oil
or silicone spray for oiling.
8. Dirt could make difficult the function of your stroller. Clean your stroller regularly. Oil it
when necessary. Do not over-oil as this may contribute to the faster soiling of the over-oiled
parts.
9. Clean the fabrics, plastic parts and metal parts of the stroller with s damp cotton cloth or
sponge and mild soap.
10. Do not use abrasive, bleach or other aggressive detergents
11. Always leave the stroller after cleaning to fully dry before use or storage.
12. In case your stroller has been stored in wet environment, you must first unfold it and
leave it to dry out in a warm place. Your stroller may corrode due to environmental influences,
such as sea air, road salt, acid rain, etc., as well as storing outside. Always store your stroller
indoors.
13. Too much sun exposure can make the plastic parts wear out faster and the fabrics fade
out.
14. Please, contact your authorized dealer for problems connected with the use or repair of
this stroller.
15. A full check from the technician is recommended if you have stored the stroller for a
long period of time or want to use it for another child.
Fabric:
Shell: 100% polyester
Filling: 100% polyester
2012/AB
12
1 Golyamokonarsko shosse, Plovdiv, BULGARIA
www.chipolino.com
Loading...