CHINA ELECTRONICS Q11 User Manual

Block Outdoor Waterproof

Bluetooth® Speaker

Instruction Manual

Q11

1.

Power ON/OFF

2.

Mode - (Play/
Pause/Call Button)

3.

Charging Port

4.

Reset Button

What’s included:

1 x Block Speaker
1 x USB to Micro-USB charging cable
1 x Instruction Manual

LED Indicator

Charging: Glowing Red LED

•
Charging Complete: Red LED off

•
Pairing Mode: Flashing Blue LED

•
Connected: Slow Pulse, Blue LED

•
Low Battery: Flashing Red LED

•

Tech Specications

Pairing Name: “Block Speaker”

•
Battery capacity: 400mAh/3.7V

•
Listening Time (at max vol): 1.5 - 2 hours

•
Charging Time: 1 hour

•

5.

LED Indicator

6.

Line-In Cover

7.

Carrying Loop

8.

Foot/Base

Instructions:

Charging the speaker:

1.
Using a Regulated USB Adapter:

a

Connect the provided USB cable to a

•
regula ted USB adapter.
Connect the oposite, Micro-USB end of the

•
cable to the charging port on the speaker.
Plug the USB adapter into the outlet to

•
begin charging.
Using a Computer:

b.

Connect a USB cable to a USB outlet on

•
your computer.

Make sure the computer is on to begin

*

charging the speaker.

Connecting the speaker with Bluetooth:

2.
Press and hold the Power ON/OFF button

a.

until the tone sounds and Blue LED begins

ashing.

Once on, the speaker will enter Bluetooth

•
mode.
Using a Bluetooth enabled device, search

•
for “Block Speaker” from the list of
available options.
Blue LED will adjust to a solid glow once

•
paired successfully.
Using the Speaker:

3.
Mode Button:

a.

Short press: play/pause the audio

•
Short Press: answer incoming call

•
Short Press: hang up ongoing call

•
Long Press: disconnect Bluetooth device

•
Double Press: Redial most recent number

•
Track Selection/Volume:

b.

Use the audio device to control track

•
selectionand volume

Note: In order to charge device use only

*

accessory cable (provided with device) or
the cable included with your own device by
the manufacturer.

SAFETY PRECAUTIONS:

WARNING–When using this product, basic

•
precautions should always be followed,
including the following:
Read all the instructions before using the

1.
product.
Charge the speaker completely before

2.
initial use for best practices.
If the device does not respond once it

3.
is powered on, the battery capacity may
be low. Do not over charge the internal

4.
battery.

5.
Do not immerse into water or expose it to
moisture or weather conditions.

6.
Do not drop, knock, or shake. Rough
handling can damage the internal precision
component and its boards.

7.
Keep away from children, this device is
not a toy.

8.

Keep away from re or other sources of

heat. Expose to high temperatures may
cause it to explode.

9.
Do not short-circuit, as this may cause
damage to the unit.

10.

Unauthorized changed or modications

may void your right to use this product.

11.
While using, always comply with any
special regulations that may apply to the
area you are in and always turn off your
mobile device when its use is prohibited.

FCC Statement:

This device complies with Part 15 of the

•
FCC Rules. Operation is subject to the
following two conditions:
This device may not cause harmful

(1)

interference, and
This device must accept any interference

(2)

received, including interference that may
cause undesired operation.

Warning:

*

Changes or modications not expressly

approved by the party responsible for
compliance could void the user’s authority
to operate the equipment.

This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment
generates, uses and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may
cause harmful interference to radio
communications. However, there is no
guarantee that interference will not
occur in a particular installation. If
this equipment does cause harmful
interference to radio or television
reception, which can be determined by
turning the equipment off and on, the
user is encouraged to try to correct
the interference by one or more of the
following measures:
o Reorient or relocate the receiving antenna.
o Increase the separation between the
equipment and receiver.
o Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
o Consult the dealer or an experienced radio/TV
technician for help.

The device has been evaluated to meet general RF exposure
requirement. The device can be used in portable exposure
condition without restriction.

MADE IN CHINA