Chimera F2X Assembling Instructions

1

Outline - F2X Assembly Instructions

Basic Information

 Layout the parts, grouping by color codes. Poles are bundled in specific groups for your

convenience.

 Align tubes carefully as to not cross thread. Laying on the floor or a flat surface is helpful. Do not

force if you encounter undue resistance.

 Start the first bay on one side, and then complete the opposite side, working a bay at a time, adding

top perimeter tubes as you go - bay by bay.

 Position all the cross tubes tabs on the same side of the uprights, either all to left of all to right

throughout, except as noted for the ends (1). Slide all tabbed parts over the threads carefully.

 It is recommended to pre-assemble all cross tubes, including the light support assemblies (adjusting

and locking the light tube angles (2) for efficiency.

 Refer to the drawings for further instructions.

 It is recommended to lubricate the threads occasionally with Dry Slide Teflon Powder for easier

assembly.

 Swivel tube Tabs. Each cross tube, when assembled, should have a stationary tab on one end and a

swivel tab on the other end. This allows the tabs to be properly aligned during frame assembly. Tube
components that have the swivel tabs are identified by a stripe of red tape on the tab end (3).

(1)

[e-mail]

www.chimeralighting.com

1812 Valtec Lane

Boulder, Colorado 80301

Phone: [phone]

Fax: [phone]

Toll Free: [phone]

2

Start

Position all the bottom perimeter tubes first.

Cross Brace Assembly (10x20’ and 10x30’ only)

Layout a corner with a bottom long side tube, an assembled bottom end cross tube, one upright and an
end cap.

As you assemble, the threaded studs will all be pointing in the same direction.

Repeat this for the opposite side.

Next, assemble the bottom tubes of the next bay, with the upright tubes between the bays.

Now go back and finish the top tube sections of the first bay.

Continue this procedure throughout the remaining bays.

Bracing Tubes

The upright tubes that support the bracing cross tubes have Velcro

TM

strips on the top end. When laying

these out, position the uprights so when lifted into position, the VelcroTM is on the inside.

To assemble the bracing cross tubes:

1. attach a VelcroTM tube cross brace bracket on an upright on one side

2. insert bracing cross tube into its receptacle.

3. put opposite receiver onto the cross tube.

4. position the VelcroTM receiver unit on opposite side upright tube and slide this upward to produce
tight fit. Securely wrap with the VelcroTM wraps.

Finishing Frame

When the frame is completely assembled, check squareness - nudge as needed to help straighten. This
can be done by eye.

Now position the entire frame up on supports - off ground - on short stands, apple boxes, etc.

Attach web strap supports as per drawing details.

1. strap clips are positioned to inside (so they don’t rub against cover).

2. adjust until taut - not overly tight.

Attach all lights and wiring with cables over top edge and hang down the sides.

Test lights before proceeding. It is suggested that you have an electrician check your electricity
requirements. Check grounding carefully and make sure that the total light amperage is appropriate for
the circuit breaker ratings.

Attach the inner baffle - clip to frame as per the drawing detail. First attach to diagonal corners and then
the opposite diagonals and pull the fabric taut.

3

Lightbank Cover

CAUTION: take extreme care in next step to not get front diffuser dirty by dragging on the floor or
ground. You can put clean material down over a dirty surface - tape it securely so it doesn’t move. Raise
your F2X frame off the ground at this stage, but not too high, approximately 2 feet, either on short light
stands or apple boxes, etc.

Spread the cover and attach the four corner straps. Then lift and attach the end panels. Cover panels
go inside top tube, over, and out and then Velcro’s to itself.

Start to lift and attach side panels to every other bay. Finish by going around up to three times to tighten
and smooth out the entire cover.

Top cover is spread over the top of the unit and attaches first to ends and again is stretched to flatten
and smooth out material.

Rigging

The last step is to rig your F2 Lightbank. Your options are:

1. on light stands

2. rope and pulley

3. FOBA motorized systems – www.foba.com/eng/decken/decken.htm

Also see the assembly video in our video library: www.chimeralighting.com.