Polarizer (CF side) Super Wide View Anti-glare coating, 709.7(H) x 405(W)
Polarizer (TFT side) Super Wide View, 709.7(H) x 405(W).
1366
768
(Typical value measured at CMI’s module: V315B6-L01)
(Typical value measured at CMI’s module: V315B6-L01)
G=0.277, 0.598
B=0.145, 0.066
W=0.285, 0.293
(Typical value measured at CMI’s module: V315B6-L01)
5.8%Typ.
(Typical value measured at CMI’s module: V315B6-L01)
Haze:11% Hardness:3H
Haze:11% Hardness:3H
1.3 MECHANICAL SPECIFICATIONS
Item Min. Typ. Max. Unit Note
Weight 1150 g I/F connector mounting
position
Note (1) Please refer to the attached drawings for more information of front and back outline dimensions.
(2) Connector mounting position
Version 2.0 4 Date
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
The mounting inclination of the connector makes
the screen center within ±0.5mm as the horizontal.
+/- 0.5mm
(2)
ΚΚΚΚ
21 JAN 2011
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT SPECIFICATION
2. ABSOLUTE MAXIMUM RATINGS
2.1 ABSOLUTE RATINGS OF ENVIRONMENT
Item Symbol
Storage Temperature TST -20 +60 ºC (1), (3)
Operating Ambient Temperature TOP 0 50 ºC (1), (2), (3)
Altitude Operating A OP 0 5000 M (3)
Altitude Storage A ST 0 12000 M (3)
Note (1) Temperature and relative humidity range is shown in the figure below.
(a) 90 %RH Max. (Ta
(b) Wet-bulb temperature should be 39 ºC Max. (Ta > 40 ºC).
(c) No condensation.
Љ 40 ºC).
Relative Humidity (%RH)
Value
Min. Max.
Unit Note
Note (2) The maximum operating temperature is based on the test condition that the surface temperature
100
80
60
40
20
90
10
Operating Range
Storage Range
Temperature (ºC)
8060-20 400 20-40
of display area is less than or equal to 65 ºC with LCD module alone in a temperature controlled
chamber. Thermal management should be considered in your product design to prevent the
surface temperature of display area from being over 65 ºC. The range of operating temperature
may degrade in case of improper thermal management in your product design.
Note (3) The rating of environment is base on LCD module. Leave LCD cell alone, this environment condition
can’t be guaranteed. Except LCD cell, the customer has to consider the ability of other parts of LCD
module and LCD module process.
Version 2.0 5 Date
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
ΚΚΚΚ
21 JAN 2011
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT SPECIFICATION
2.2 ABSOLUTE RATINGS OF ENVIRONMENT (OPEN CELL)
Storage Condition: With shipping package.
Storage temperature range: 25±5
Storage humidity range: 50±10%RH
Shelf life: a month
2.3 ELECTRICAL ABSOLUTE RATINGS
2.3.1 TFT LCD OPEN CELL
Item Symbol
Power Supply Voltage Vcc -0.3 13.5 V
Input Signal Voltage VIN -0.3 3.6 V
Note (1) Permanent damage to the device may occur if maximum values are exceeded. Functional
operation should be restricted to the conditions described under normal operating conditions.
к
Value
Min. Max.
Unit Note
(1)
Version 2.0 6 Date
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
ΚΚΚΚ
21 JAN 2011
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT SPECIFICATION
3. ELECTRICAL CHARACTERISTICS
3.1 TFT LCD OPEN CELL
Parameter Symbol
Power Supply Voltage VCC 10.8 12.0 13.2 V (1)
Rush Current I
White - 0.51 - A
Power Supply Current
Differential Input High
Threshold Voltage
LVDS
Interface
Differential Input Low
Threshold Voltage
Common Input Voltage VCM 1.0 1.2 1.4 V
Differential input voltage |VID| 200 - 600 mV
Terminating Resistor R
Input High Threshold Voltage VIH 2.7 - 3.3 V CMOS
interface
Input Low Threshold Voltage V
Note (1) The module should be always operated within above ranges.
Horizontal Stripe- 0.6 0.72 A
Black
Ta = 25 ± 2ºC
Value
Min. Typ. Max.
- - 3.3 A (2)
RUSH
Unit Note
ICC
- 0.4 - A
+100 - - mV
V
LVT H
- - -100 mV
V
LVTL
- 100 - ohm
T
0 - 0.7 V
IL
(3)
(4)
Note (2) Measurement Conditions:
(Low to High)
(Control Signal)
SW
+12.0V
R1
1K
R2
1K
Q1 Si4435DY
VR1
47K
Q2
2N7002
Vcc rising time is 470us
C1
+12V
0.01uF
FUSE
C3
1uF
Vcc
(LCD Module Input)
0.9Vcc
0.1Vcc
GND
470us
Version 2.0 7 Date
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
ΚΚΚΚ
21 JAN 2011
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT SPECIFICATION
Note (3) The specified power supply current is under the conditions at Vcc =12V, Ta = 25 ± 2 ºC, fv = 60
Hz, whereas a power dissipation check pattern below is displayed.
a. White Pattern
Active Area
b. Black Pattern
Active Area
c. Vertical Stripe Pattern
Active Area
Note (4) The LVDS input characteristics are as follows:
Version 2.0 8 Date
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
ΚΚΚΚ
21 JAN 2011
www.panelook.com
Global LCD Panel Exchange Center
(+/
)
www.panelook.com
4. BLOCK DIAGRAM
4.1 TFT LCD OPEN CELL
RX0(+/-)
RX1(+/-)
RX2(+/-)
RX3(+/-)
RXCLK
SELLVDS
ODSEL
Vcc
GND
-
P-TWO 187053-30091)
093G30-B0001A or
PRODUCT SPECIFICATION
INPUT CONNECTOR
(STARCONN
FRAME BUFFER
TIMING
SCAN DRIVER IC
TFT LCD PANEL
(1366x3x768)
CONTROLLER
DC/DC CONVERTER &
REFERENCE VOLTAGE
DATA DRIVER IC
Version 2.0 9 Date
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
ΚΚΚΚ
21 JAN 2011
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT SPECIFICATION
5. INTERFACE PIN CONNECTION
5.1 TFT LCD OPEN CELL
CNF1 Connector Pin Assignment
Pin No. Symbol Description Note
1 VCC Power supply: +12V
2 VCC Power supply: +12V
3 VCC Power supply: +12V
4 VCC Power supply: +12V
5 GND Ground
6 GND Ground
7 GND Ground
8 GND Ground
9 SELLVDS Select LVDS data format (2)(6)
10 ODSEL Overdrive Lookup Table Selection (3)(6)
11 GND Ground
12 RX0- Negative transmission data of pixel 0
13 RX0+ Positive transmission data of pixel 0
14 GND Ground
15 RX1- Negative transmission data of pixel 1
16 RX1+ Positive transmission data of pixel 1
17 GND Ground
18 RX2- Negative transmission data of pixel 2
19 RX2+ Positive transmission data of pixel 2
20 GND Ground
21 RXCLK- Negative of clock
22 RXCLK+ Positive of clock
23 GND Ground
24 RX3- Negative transmission data of pixel 3
25 RX3+ Positive transmission data of pixel 3
26 GND Ground
27 TST_AGE Aging Mode (4)
28 NC No connection (5)
29 GND Ground
30 GND Ground
Note (1) Connector type: STARCONN 093G30-B0001A or P-TWO 187053-30091 or compatible
LVDS connector pin orderdefined as follows
Note (2) Low = Open or connect to GND: VESA Format, High = Connect to +3.3V: JEIDA Format.
Please refer to 5.5 LVDS INTERFACE
Note (3) Overdrive lookup table selection. The Overdrive lookup table should be selected in accordance to the
frame rate to optimize image quality.
Version 2.0 10 Date
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
ΚΚΚΚ
21 JAN 2011
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT SPECIFICATION
Low = Open or connect to GND, High = Connect to +3.3V
ODSEL Note
L or Open Lookup table was optimized for 60 Hz frame rate.
H Lookup table was optimized for 50 Hz frame rate.
Note (4) Ground or OPEN: Disable, High: Enable.
Note (5) Reserved for internal use. Left it open.
Note (6) LVDS signal pin connected to the LCM side has the following diagram.
R1 in the system side should be less than 1K Ohm. (R1 < 1K Ohm)
Version 2.0 11 Date
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
ΚΚΚΚ
21 JAN 2011
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
5.2 BLOCK DIAGRAM OF INTERFACE
R0-R7
-
-
Host
Graphics
Controller
LVDS Transmitter
THC63LVDM83A
(LVDF83A)
CNF1
Rx0+
-
Rx1+
Rx1-
Rx2+
-
Rx3+
-
CLK+
PRODUCT SPECIFICATION
51
Ө
100pF
51
Ө
51
Ө
51
51
51
51
51
51
51
100pF
Ө
Ө
100pF
Ө
Ө
100pF
Ө
Ө
100pF
Ө
-
LVDS Receiver
THC63LVDF84A
RxOUT
R0-R7
-
-
DCLK
Timing
Controller
R0~R7 : Pixel R Data
G0~G7 : Pixel G Data
B0~B7 : Pixel B Data
DE : Data enable signal
DCLK : Data clock signal
Note (1) The system must have the transmitter to drive the module.
Note (2) LVDS cable impedance shall be 50 ohms per signal line or about 100 ohms per twist-pair line when it is
used differentially.
Version 2.0 12 Date
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
ΚΚΚΚ
21 JAN 2011
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
5.3 LVDS INTERFACE
VESA LVDS formaΚʻ˦˘˟˟˩˗˦ʳ˼ː˟ʳʳ˸ʼ
JEDIA LVDS formaΚʻ˦˘˟˟˩˗˦ʳ˼ː˛ʼ
PRODUCT SPECIFICATION
R0~R7: Pixel R Data (7; MSB, 0; LSB)
G0~G7: Pixel G Data (7; MSB, 0; LSB)
B0~B7: Pixel B Data (7; MSB, 0; LSB)
DE : Data enable signal
Note (1) RSVD(reserved)pins on the transmitter shall be “H” or( “L” or OPEN)
Version 2.0 13 Date
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
ΚΚΚΚ
21 JAN 2011
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT SPECIFICATION
5.4 COLOR DATA INPUT ASSIGNMENT
The brightness of each primary color (red, green and blue) is based on the 8-bit gray scale data input
for the color. The higher the binary input, the brighter the color. The table below provides the assignment
Note (2) ˧˻˼ʳmodule is operated in DE only mode and please follow the input signal timing diagram beloΚʳ
Total
Display
Blank
˙
˶˿˾˼ʻ˴ʼ
˙
ˈ
ʳЊʳ˙
ˉ
ʳ Ѽʳ ˧ʳ Ѽʳ ˧˻ʳ Њʳ ˙
ʳ Ѽʳ ˧ʳ Ѽʳ ˧˻
˶˿˾˼ʻ˼ʼʳ
Fr6 57 60 63 Hz
Tv 778 806 888 Th
Tvd 768 768 768 Th
Tvb 10 38 120 Th
Th 1442 1560 1936 Tc
Thd 1366 1366 1366 Tc
Thb 76 194 570 Tc
ʳ
Tv=Tvd+T vb
Th=Thd+Thb
(6)
Ё
Ё
Ё
Ё
Version 2.0 16 Date
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
ΚΚΚΚ
21 JAN 2011
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT SPECIFICATION
INPUT SIGNAL TIMING DIAGRAM
DE
DCLK
T
h
Tvd
Tv
Tvb
Thd
DE
DATA
Valid display data (1366clocks)
Note (3) The input clock cycle-to-cycle jitter is defined as below figures. Trcl = I T1 – TI
Version 2.0 17 Date
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
ΚΚΚΚ
21 JAN 2011
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT SPECIFICATION
Note (4) The SSCG (Spread spectrum clock generator) is defined as below figures.
Note (5) The LVDS timing diagram and setup/hold time is defined and showing as the following
figures.
RXCLK+/-
RXn+/-
Tlvsu
Tlvhd
1T
14
LVDS RECEIVER INTERFACE TIMING DIAGRAM
Tc
3T
14
5T
14
7T
14
9T
14
11T
14
13T
14
Note (6) : (ODSEL) = H/L or open for 50/60Hz frame rate. Please refer to 5.1 for detail information
Version 2.0 18 Date
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
ΚΚΚΚ
21 JAN 2011
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT SPECIFICATION
6.2 POWER ON/OFF SEQUENCE
(Ta = 25 2 ºC)
To prevent a latch-up or DC operation of LCD module, the power on/off sequence should be as
the diagram below.
Power Supply
V
0.5
0
0
500ms
LVDS Signals
0
0
CC
ЉЉЉЉ
T
1
ЉЉЉЉ
10ms
ЉЉЉЉ
T
2
ЉЉЉЉ
50ms
ЉЉЉЉ
T
3
ЉЉЉЉ
50ms
ЉЉЉЉ
T4
ЉЉЉЉ
T
7
ЉЉЉЉ
T2
ЉЉЉЉ
T
8
ЉЉЉЉ
T3
Option Signals
(SELLVDS, ODSEL)
0V
0V
0.9 V
CC
0.1V
CC
Power On
T7
CC
0.9 V
cc
0.1V
T
3
T1
2
T
T4
VALI D
Power Off
8
T
Backlight (Recommended)
ЉЉЉЉ
ЉЉЉЉ
T5
T
6
500ms
100ms
50%
5
T
50%
6
T
Note (1) The supply voltage of the external system for the module input should follow the definition of Vcc.
Note (2) Apply the lamp voltage within the LCD operation range. When the backlight turns on before the LCD
operation or the LCD turns off before the backlight turns off, the display may momentarily become
abnormal screen.
Note (3) In case of Vcc is in off level, please keep the level of input signals on the low or high impedance.
T2<0, that maybe cause electrical overstress failures.
Note (4) T4 should be measured after the module has been fully discharged between power off and on period.
Note (5) Interface signal shall not be kept at high impedance when the power is on.
Power ON/OFF Sequence
If
Version 2.0 19 Date
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
ΚΚΚΚ
21 JAN 2011
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT SPECIFICATION
7. OPTICAL CHARACTERISTICS
7.1 TEST CONDITIONS
Item Symbol Value Unit
Ambient Temperature Ta
Ambient Humidity Ha
Supply Voltage VCC 5.0 V
Input Signal According to typical value in "3. ELECTRICAL CHARACTERISTICS"
Inverter Current IL
Inverter Driving Frequency FL
25±2
50±10
10.5
63
0.5
3
7.2 OPTICAL SPECIFICATIONS
The relative measurement methods of optical characteristics are shown as below. The following items
should be measured under the test conditions described in 7.1 and stable environment shown in Note (5).
Item SymbolCondition Min. Typ. Max. UnitNote
Red
Color
Chromaticity
Center Transmittance T%
Contrast Ratio CR
Response Time
White Variation
Viewing Angle
Green
Blue
White
Horizontal
Vertical
Rx
Ry 0.332
Gx
Gy 0.598
Bx
By 0.066
Wx
Wy
Gray to
gray
average
δW
θx+
-
θ
x
θY+
θ
-
Y
=0°, θY =0°
θ
x
˩˼˸˼˺ʳ˴˺˿˸ʳ˴ʳ˴˿ʳ
˷˼˸˶˼
With CMO module
θ
=0°, θY =0°
x
With CMO Module
θ
=0°, θY =0°
x
With CMO
Module@60Hz
=0°, θY =0°
θ
x
With CMO Module
CR≥20
With CMO Module
Typ.-0.03
- 5.8 % (1), (7)
2000 3000- (1), (3)
-
1.5 - (1), (6)
80 88 80
80
80
0.642
0.277
0.145
0.285
0.293
Typ+0.03
6.5 12
88 88 88 -
o
C
%RH
mA
KHz
-
-
-
-
-
-
-
-
ms (4)
Deg. (1), (2)
(1),(5)
Note (1) Light source is CMO’s BLU(V315B6-L01) and driving voltages are based on suitable gamma voltages.
The calculated method is as following:
1. Measure module’s and backlight’s spectrum. White and R, G, B are with signal input.
2. Calculate cell’s spectrum.
Note (2) Definition of Viewing Angle (θx, θy):
Viewing angles are measured by Autronic Conoscope Cono-80
Version 2.0 20 Date
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
ΚΚΚΚ
21 JAN 2011
www.panelook.com
Global LCD Panel Exchange Center
T
www.panelook.com
PRODUCT SPECIFICATION
θX- = 90º
6 o’clock
θ
y-
= 90º
x-
y-
Normal
θx = θy = 0º
θy-θy+
θx−
θx+
y+
12 o’clock direction
θ
y+
= 90º
x+
θX+ = 90º
Note (3) Definition of Contrast Ratio (CR):
The contrast ratio can be calculated by the following expression.
Contrast Ratio (CR) = L255 / L0
L255: Luminance of gray level 255
L 0: Luminance of gray level 0
CR = CR (5), where CR (X) is corresponding to the Contrast Ratio of the point X at the figure in Note
(6).
Note (4) Definition of Gray-to-Gray Switching Time:
Optical
Response
100%
90%
10%
0%
Gray to gray
Switching time
Gray to gray
Switching time
ime
The driving signal means the signal of gray level 0, 123, 168, 202, 230, 255. Gray to gray average time
means the average switching time of gray level 0, 123, 168, 202, 230, 255 to each other.
Note (5) Measurement Setup:
The LCD module should be stabilized at given temperature for 60 minutes to avoid abrupt
Version 2.0 21 Date
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
ΚΚΚΚ
21 JAN 2011
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT SPECIFICATION
temperature change during measuring. In order to stabilize the luminance, the measurement
should be executed after lighting Backlight for 60 minutes in a windless room.
LCD Module
LCD Panel
Field of View = 1º
CS-2000
500 mm
Light Shield
(Ambient Luminance < 2 lux)
Note (6) Definition of White Variation (δW):
Measure the luminance of gray level 255 at 5 points
δW = Maximum [L (1), L (2), L (3), L (4), L (5)] / Minimum [L (1), L (2), L (3), L (4), L (5)]
where L (X) is corresponding to the luminance of the point X at the figure below.
Vertical Line
W
W/4
W/2
3W /4
Horizontal Line
D
D/4D/23D/4
12
: Test Point
5
34
X
X=1 to 5
Note (7) Definition of Transmittance (T%):
Module is without signal input.
Transmittance =
Luminance of LCD module
Luminance of backlight
Active Area
Ϡ 100%
Version 2.0 22 Date
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
ΚΚΚΚ
21 JAN 2011
www.panelook.com
Global LCD Panel Exchange Center
n
www.panelook.com
PRODUCT SPECIFICATION
8. DEFINITION OF LABELS
8.1 OPEN CELL LABEL
The barcode nameplate is pasted on each module as illustration, and its definitions are as following
explanation.
CHI MEI
OPTOELECTRONICS
V320BJ2 –P01 Rev. XX
X X X X X X X XXXXN N N N
CHI MEI
OPTOELECTRONICS
V320BJ2 –P01 Rev. XX
E207943
MADE IN TAIWAN
GEMN
MADE IN CHINA
LEOO(or CAPG or CANO)
RoHS
Model Name: V320BJ2-P01
Revision: Rev. XX, for example: A0, A1… B1, B2… or C1, C2…etc.
Serial ID: X X X X X X X Y M D L N N N N
Serial No.
Product Line
Year, Month, Date
CMO Internal Use
Serial ID includes the information as below:
Manufactured Date:
Year: 2010=0, 2011=1,2012=2…etc.
Month: 1~9, A~C, for Jan. ~ Dec.
CMO Internal Use
Revisio
CMO Internal Use
Day: 1~9, A~Y, for 1st to 31st, exclude I ,O, and U.
Revision Code: Cover all the change
Serial No.: Manufacturing sequence of product
Product Line: 1 -> Line1, 2 -> Line 2, …etc.
Version 2.0 23 Date
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
ΚΚΚΚ
21 JAN 2011
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
9. PACKAGING
9.1 PACKING SPECIFICATIONS
(1) 18 LCD TV Panels / 1 Box
(2) Box dimensions : 970 (L) X 640 (W) X 319 (H)
(3) Weight : approximately 36Kg ( 18 panels per box)
9.2 PACKING METHOD
Figures 9-1 and 9-2 are the packing method
PRODUCT SPECIFICATION
Version 2.0 24 Date
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Figure.9-1 packing method
ΚΚΚΚ
21 JAN 2011
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT SPECIFICATION
Figure.9-2 packing method
Version 2.0 25 Date
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
ΚΚΚΚ
21 JAN 2011
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT SPECIFICATION
10. PRECAUTIONS
10.1 ASSEMBLY AND HANDLING PRECAUTIONS
(1) Do not apply rough force such as bending or twisting to the product during assembly.
(2) To assemble backlight or install module into user’s system can be only in clean working areas. The
dust and oil may cause electrical short or worsen the polarizer.
(3) It’s not permitted to have pressure or impulse on the module because the LCD panel will be
damaged.
(4) Always follow the correct power sequence when the product is connecting and operating. This can
prevent damage to the CMOS LSI chips during latch-up.
(5) Do not pull the I/F connector in or out while the module is operating.
(6) Use a soft dry cloth without chemicals for cleaning, because the surface of polarizer is very soft and
easily scratched.
(7) It is dangerous that moisture come into or contacted the product, because moisture may damage the
product when it is operating.
(8) High temperature or humidity may reduce the performance of module. Please store this product within
the specified storage conditions.
(9) When ambient temperature is lower than 10ºC may reduce the display quality. For example, the
response time will become slowly.
10.2 SAFETY PRECAUTIONS
(1) If the liquid crystal material leaks from the panel, it should be kept away from the eyes or mouth. In
case of contact with hands, skin or clothes, it has to be washed away thoroughly with soap.
(2) After the product’s end of life, it is not harmful in case of normal operation and storage.
Version 2.0 26 Date
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
ΚΚΚΚ
21 JAN 2011
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
11. Mechanical Drawing
PRODUCT SPECIFICATION
Version 2.0 27 Date
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
ΚΚΚΚ
21 JAN 2011
www.panelook.com
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.