CHIMEI INNOLUX N154Z6-L02 Specification
Global LCD Panel Exchange Center
ಖᙕ
ՠ܂
ᐉு
ߡۥ
ދป
A
TFT LCD Preliminary Specification
MODEL NO.: N154Z6 - L02
(Without Converter)
www.panelook.com
Doc. No.:
Issued Date: Jul. 24, 2008
Model No.: N154Z6 - L02
Preliminary
Customer :
pproved by :
Note :
2008-08-20
11:43:20 CST
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
PMMD III
Director
masao(׆إ
ႂ/#10936)
1 / 27
Director
(deputy)
Accept
Version 1.0
www.panelook.com
Global LCD Panel Exchange Center
REVISION HISTORY
www.panelook.com
Doc. No.:
Issued Date: Jul. 24, 2008
Model No.: N154Z6 - L02
Preliminary
- CONTENTS -
------------------------------------------------------- 3
1. GENERAL DESCRIPTION
1.1 OVERVIEW
1.2 FEATURES
1.3 APPLICATION
1.4 GENERAL SPECIFICATIONS
1.5 MECHANICAL SPECIFICATIONS
------------------------------------------------------- 4
2. ABSOLUTE MAXIMUM RATINGS ------------------------------------------------------- 5
2.1 ABSOLUTE RATINGS OF ENVIRONMENT
2.2 ELECTRICAL ABSOLUTE RATINGS
2.2.1 TFT LCD MODULE
2.2.2 BACKLIGHT UNIT
3. ELECTRICAL CHARACTERISTICS
3.1 TFT LCD MODULE
3.2 BACKLIGHT UNIT
------------------------------------------------------- 7
4. BLOCK DIAGRAM ------------------------------------------------------- 11
4.1 TFT LCD MODULE
4.2 BACKLIGHT UNIT
5. INPUT TERMINAL PIN ASSIGNMENT ------------------------------------------------------- 12
5.1 TFT LCD MODULE
5.2 BACKLIGHT UNIT
5.3 TIMING DIAGRAM OF LVDS INPUT SIGNAL
5.4 COLOR DATA INPUT ASSIGNMENT
5.5 EDID DATA STRUCTURE
6. INTERFACE TIMING ------------------------------------------------------- 18
6.1 INPUT SIGNAL TIMING SPECIFICATIONS
6.2 POWER ON/OFF SEQUENCE
7. OPTICAL CHARACTERISTICS ------------------------------------------------------- 20
7.1 TEST CONDITIONS
7.2 OPTICAL SPECIFICATIONS
8. PRECAUTIONS ------------------------------------------------------- 23
8.1 ASSEMBLY AND HANDLING PRECAUTIONS
8.2 SAFETY PRECAUTIONS
9. PACKING ------------------------------------------------------- 24
9.1 CARTON
9.2 PALLET
10. DEFINITION OF LABELS
10
.1 CMO MODULE LABEL
10.2 CMO CARTON LABEL
------------------------------------------------------- 26
2 / 27
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Version 1.0
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Doc. No.:
Issued Date: Jul. 24, 2008
Model No.: N154Z6 - L02
Preliminary
REVISION HISTORY
Version Date
Ver 1.0 Jul. 24,’08 All All Preliminary Specification was first issued.
Page
(New)
Section Description
3 / 27
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Version 1.0
www.panelook.com
Global LCD Panel Exchange Center
1. GENERAL DESCRIPTION
1.1 OVERVIEW
N154Z6 - L02 is a 15.4” TFT Liquid Crystal Display module with single LED Backlight unit and 30 pins
LVDS interface. This module supports 1680 x 1050 Wide-SXGA+ mode and can display 262,144 colors.
The optimum viewing angle is at 6 o’clock direction.
1.2 FEATURES
- Thin and High Brightness
- WSXGA+ (1680 x 1050 pixels) resolution
- DE only mode
- 3.3V LVDS (Low Voltage Differential Signaling) interface with 2 pixel/clock
- Meet RoHS requirement
www.panelook.com
Doc. No.:
Issued Date: Jul. 24, 2008
Model No.: N154Z6 - L02
Preliminary
1.3 APPLICATION
- TFT LCD Notebook
1.4 GENERAL SPECIFICATI0NS
Item Specification Unit Note
Active Area 331.128 (H) x 206.955 (V) (15.4 inch Diagonal) mm
Bezel Opening Area 335 (H) x 211.1 (V) mm
Driver Element a-si TFT active matrix - Pixel Number 1680 x 3 (RGB) x 1050 pixel Pixel Pitch 0.1971 x 0.1971 mm Pixel Arrangement RGB vertical stripe - Display Colors 262,144 color Transmissive Mode Normally white - Surface Treatment Hard coating (3H), Anti-glare - -
1.5 MECHANICAL SPECIFICATIONS
Item Min. Typ. Max. Unit Note
Horizontal (H) 343.5 344 344.5 mm
Module Size
Note (1) Please refer to the attached drawings for more information of front and back outline dimensions.
Vertical (V) 221.5 222 222.5 mm
Depth (D) --- 6.0 6.3 mm
Weight --- 515 530 g -
(1)
(1)
4 / 27
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Version 1.0
www.panelook.com
Global LCD Panel Exchange Center
2. ABSOLUTE MAXIMUM RATINGS
2.1 ABSOLUTE RATINGS OF ENVIRONMENT
Item Symbol
Storage Temperature TST -20 +60 ºC (1)
Operating Ambient Temperature TOP 0 +50 ºC (1), (2)
Shock (Non-Operating) S
Vibration (Non-Operating) V
Note (1) Temperature and relative humidity range is shown in the figure below.
(a) 90 %RH Max. (Ta Љ 40 ºC).
(b) Wet-bulb temperature should be 39 ºC Max. (Ta > 40 ºC).
(c) No condensation.
Note (2) The temperature of panel surface should be 0 ºC Min. and 50 ºC Max.
www.panelook.com
Min. Max.
- 220/2 G/ms (3), (5)
NOP
- 1.5 G (4), (5)
NOP
Value
Doc. No.:
Issued Date: Jul. 24, 2008
Model No.: N154Z6 - L02
Preliminary
Unit Note
Relative Humidity (%RH)
100
90
80
60
Operating Range
40
20
10
Storage Range
Temperature (ºC)
Note (3) 1 time for ± X, ± Y, ± Z. for Condition (220G / 2ms) is half Sine Wave,
8060-20 400 20-40
Note (4) 10 ~ 500 Hz, 0.5 Hr / Cycle, 1 cycles for each X, Y, Z.
Note (5) At testing Vibration and Shock, the fixture in holding the module has to be hard and rigid enough
so that the module would not be twisted or bent by the fixture.
The fixing condition is shown as below:
LCD Module
Side Mount Fixing Screw
gap=2mm
Bracket
Side Mount Fixing Screw
Stage
5 / 27
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Version 1.0
www.panelook.com
Global LCD Panel Exchange Center
2.2 ELECTRICAL ABSOLUTE RATINGS
2.2.1 TFT LCD MODULE
Item Symbol
Power Supply Voltage VCC -0.3 +4.0 V
Logic Input Voltage VIN -0.3 VCC+0.3 V
2.2.2 BACKLIGHT UNIT
Item
LED Light Bar Power Supply Voltage -5 * 8 3.4 * 8 V
LED Light Bar Power Supply Current -- 30 * 6 mA
Note (1) Permanent damage to the device may occur if maximum values are exceeded. Function operation
should be restricted to the conditions described under Normal Operating Conditions.
www.panelook.com
Value
Min. Max.
Value
Min Max.
Unit Note
Doc. No.:
Issued Date: Jul. 24, 2008
Model No.: N154Z6 - L02
Preliminary
(1)
Unit Note
DC
DC
(1), (2)
Note (2) Specified values are for LED (Refer to Section 3.2 for further information).
6 / 27
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Version 1.0
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Doc. No.:
Issued Date: Jul. 24, 2008
Model No.: N154Z6 - L02
Preliminary
3. ELECTRICAL CHARACTERISTICS
3.1 TFT LCD MODULE Ta = 25 ± 2 ºC
Parameter Symbol
Min. Typ. Max.
Power Supply Voltage Vcc 3.0 3.3 3.6 V Ripple Voltage VRP 50 mV Rush Current I
1.5 A (2)
RUSH
Initial Stage Current IIS 1.0 A (2)
Power Supply Current
LVDS Differential Input High Threshold V
LVDS Differential Input Low Threshold V
White 350 380 mA (3)a
Black
Lcc
TH(LVDS)
TL(LVDS)
490 520 mA (3)b
+100 mV
-100 mV
LVDS Common Mode Voltage VCM 1.125 1.375 V (5)
LVDS Differential Input Voltage |VID| 100 600 mV (5)
Terminating Resistor RT 100 Ohm
Power per EBL WG P
- TBD - W (4)
EBL
Note (1) The ambient temperature is Ta = 25 ± 2 ºC.
Value
Unit Note
V
V
(5),
=1.2V
CM
(5)
=1.2V
CM
Note (2) I
I
: the maximum current when VCC is rising
RUSH
: the maximum current of the first 100ms after power-on
IS
Measurement Conditions: Shown as the following figure. Test pattern: black.
(High to Low)
(Control Signal)
SW
+12V
+3.3V
R1
47K
R2
1K
47K
VR1
C1
1uF
Q1 2SK1475
C2
0.01uF
Q2
2SK1470
FUSE
C3
1uF
Vcc
(LCD Module Input)
7 / 27
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Version 1.0
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Doc. No.:
Issued Date: Jul. 24, 2008
Model No.: N154Z6 - L02
Preliminary
Vcc rising time is 470us
VCC
0V
I
RUSH
470us
0.1Vcc
0.9Vcc
+3.3V
100ms
I
IS
ICC
Note (3) The specified power supply current is under the conditions at Vcc = 3.3 V, Ta = 25 ± 2 ºC, f
Hz, whereas a power dissipation check pattern below is displayed.
a. White Pattern
b. Black Pattern
= 60
v
Active Area
Active Area
Note (4) The specified power are the sum of LCD panel electronics input power and the converter input
power. Test conditions are as follows.
(a) Vcc = 3.3 V, Ta = 25 ± 2 ºC, f
= 60 Hz,
v
(b) The pattern used is a black and white 32 x 36 checkerboard, slide #100 from the VESA file
“Flat Panel Display Monitor Setup Patterns”, FPDMSU.ppt.
(c) Luminance: 60 nits.
(d) The converter used is provided from
. Please contact them for detail information.
CMO doesn’t provide the converter in this product.
8 / 27
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Version 1.0
www.panelook.com
Loading...