Page 1
PRODUCT SPECIFICATION
Doc. Number:
□ Tentative Specification
□ Preliminary Specification
▓ Approval Specification
MODEL NO.: N140BGE
SUFFIX: P21
Customer:
APPROVED BY SIGNATURE
Name / Title
Note
Please return 1 copy for your confirmation with your
signature and comments.
Approved By Checked By Prepared By
楊竣傑
2011-12-21
09:43:38 CST
曹文彬
2011-12-13
15:07:01 CST
何銘杰
2011-12-08
14:34:16 CST
Version 2.0 21 December 2011 1 / 26
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
Page 2
PRODUCT SPECIFICATION
CONTENTS
1. GENERAL DESCRIPTION.........................................................................................................4
1.1 OVERVIEW ................................................................................................................................4
2. MECHANICAL SPECIFICATIONS .............................................................................................4
2.1 CONNECTOR TYPE..................................................................................................................4
3. ABSOLUTE MAXIMUM RATINGS.............................................................................................6
3.1 ABSOLUTE RATINGS OF ENVIRONMENT ..........................................................................6
3.2 ABSOLUTE RATINGS OF ENVIRONMENT (OPEN CELL) .................................................6
3.3 ELECTRICAL ABSOLUTE RATINGS (OPEN CELL) ............................................................7
3.3.1 TFT LCD MODULE ............................................................................................................7
4. ELECTRICAL SPECIFICATIONS...............................................................................................8
4.1 FUNCTION BLOCK DIAGRAM...............................................................................................8
4.2. INTERFACE CONNECTIONS .................................................................................................8
4.3 ELECTRICAL CHARACTERISTICS......................................................................................11
4.3.1 LCD ELETRONICS SPECIFICATION.............................................................................11
4.3.2 LED CONVERTER SPECIFICATION..............................................................................13
4.4 LVDS INPUT SIGNAL TIMING SPECIFICATIONS .............................................................15
4.4.1 LVDS DC SPECIFICATIONS ...........................................................................................15
4.4.2 LVDS DATA FORMAT......................................................................................................15
4.4.3 COLOR DATA INPUT ASSIGNMENT ............................................................................16
4.5 DISPLAY TIMING SPECIFICATIONS ...................................................................................17
4.6 POWER ON/OFF SEQUENCE ................................................................................................18
5. OPTICAL CHARACTERISTICS ...............................................................................................19
5.1 TEST CONDITIONS.................................................................................................................19
5.2 OPTICAL SPECIFICATIONS ..................................................................................................19
6. PACKING..................................................................................................................................22
6.1 CMI OPEN CELL LABEL........................................................................................................22
6.2 Package Reliability....................................................................................................................23
6.3 CARTON...................................................................................................................................23
6.4 PALLET.....................................................................................................................................24
7. PRECAUTIONS........................................................................................................................25
7.1 HANDLING PRECAUTIONS..................................................................................................25
7.2 STORAGE PRECAUTIONS ....................................................................................................25
7.3 OPERATION PRECAUTIONS.................................................................................................25
Appendix. OUTLINE DRAWING..................................................................................................26
Version 2.0 21 December 2011 2 / 26
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
Page 3
PRODUCT SPECIFICATION
REVISION HISTORY
Version Date Page Description
1.0 Nov, 24, 2012 All Spec Ver.1.0 was first issued.
Version 2.0 21 December 2011 3 / 26
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
Page 4
PRODUCT SPECIFICATION
1. GENERAL DESCRIPTION
1.1 OVERVIEW
N140B6-P21 is a 14.0 TFT Liquid Crystal Display with LED Driver ICs and a 40-pins-and-1ch-LVDS
circuit board. This product supports 1366 x 768 HD mode and can display 262,144 colors. The
backlight unit is not built in.
1.2 GENERAL SPECIFICATI0NS
Item Specification Unit Note
Screen Size 14.0” diagonal
Driver Element a-si TFT active matrix - Pixel Number 1366 x R.G.B. x 768 pixel Pixel Pitch 0.2265 (H) x 0.2265 (V) mm Pixel Arrange ment RGB vertical stripe - Display Colors 262,144 color Transmissive Mode Normally white - Surface Treat ment Hard coating (3H), Glare - -
2. MECHANICAL SPECIFICATIONS
item Min. Typ. Max. Unit Note
Horizontal (H) with PCB 318.15 318.35 318.55 mm
Horizontal (H) w/o PCB 318.15 318.35 318.55 mm
Vertical (V) with PCB 226 227 228 mm
Size
Vertical (V) w/o PCB 183.85 184.05 184.25 mm
Thickness (T) with PCB - 1.6 1.9 mm
Thickness (T) w/o PCB - 1.265 - mm
Weight - 170 g
I/F connector mounting position
Note (1) Please refer to the attached drawings for more information of front and back outline dimensions.
(2) Connector mounting position
The mounting inclination of the connector makes
the screen center within ±0.5mm as the horizontal.
2.1 CONNECTOR TYPE
Pin1 Pin40
(1) (2)
Please refer Appendix Outline Drawing for detail design.
Connector Part No.:IPEX-20455-040E-12
User’s connector Part No: IPEX-20453-040T-01 or equivalent
Version 2.0 21 December 2011 4 / 26
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
Page 5
2.1.2 LED Light-Bar Connector
IPEX 20488-010E-01
PRODUCT SPECIFICATION
Version 2.0 21 December 2011 5 / 26
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
Page 6
PRODUCT SPECIFICATION
3. ABSOLUTE MAXIMUM RATINGS
3.1 ABSOLUTE RATINGS OF ENVIRONMENT
Item Symbol
Min. Max.
Storage Temperature TST -20 +60 ºC (1)
Operating Ambient T emperature TOP 0 +50 ºC (1), (2)
Note (1) (a) 90 %RH Max. (Ta <= 40 ºC).
(b) Wet-bulb temperature should be 39 ºC Max. (Ta > 40 ºC).
(c) No condensation.
Note (2) The temperature of panel surface should be 0 ºC min. and 60 ºC max.
Relative Humidity (%RH)
100
90
Value
Unit Note
80
60
Operating
40
20
10
Storage Range
Temperature (ºC)
3.2 ABSOLUTE RATINGS OF ENVIRONMENT (OPEN CELL)
High temperature or humidity may reduce the performance of panel. Please store LCD panel
within the specified storage conditions.
80 60 -20 40 0 20 -40
Storage Condition: With packing.
Storage temperature range: 25±5 ºC.
Storage humidity range: 50±10%RH.
Shelf life: 30days
Version 2.0 21 December 2011 6 / 26
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
Page 7
PRODUCT SPECIFICATION
3.3 ELECTRICAL ABSOLUTE RATINGS (OPEN CELL)
3.3.1 TFT LCD MODULE
Item Symbol
Power Supply V oltage VCCS -0.3 +4.0 V
Logic Input Voltage VIN -0.3 VCCS+0.3 V
Note (1) Stresses beyond those listed in above “ELECTRICAL ABSOLUTE RATINGS” may cause
permanent damage to the device. Normal operation should be restricted to the conditions
described in “ELECTRICAL CHARACTERISTICS”.
Value
Min. Max.
Unit Note
(1)
Version 2.0 21 December 2011 7 / 26
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
Page 8
4. ELECTRICAL SPECIFICATIONS
4.1 FUNCTION BLOCK DIAGRAM
LVDS Display
Data & Clock
VCCS
GND
Data
CLK
V
EDID
EDID
EDID
INPUT CONNECTOR
TIMING ONTROLLER
DC/DC CONVERTER &
REFERENCE VOLTAGE
PRODUCT SPECIFICATION
SCAN DRIVER IC
TFT LCD
PANEL
GENERATOR
DA TA DRIVER IC
EDID
EEPROM
Converter
Input Signals
4.2. INTERFACE CONNECTIONS
PIN ASSIGNMENT
Pin Symbol Description Remark
1 NC No Connection (Reserve)
2 VCCS Power Supply (3.3V typ.)
3 VCCS Power Supply (3.3V typ.)
4 VEDID DDC 3.3V power
5 NC No Connection (Reserved for CMI test)
6 CLKEDID DDC clock
7 DATAEDID DDC data
8 Rxin0- LVDS differential data input
9 Rxin0+ LVDS differential data input
10 VSS Ground
11 Rxin1 - LVDS differential data input
12 Rxin1+ LVDS diff erential data input
13 VSS Ground
14 Rxin2- LVDS Differential Data Input
15 Rxin2+ LVDS Differential Data Input
16 VSS Ground
17 RxCLK- LVDS differential clock input
18 RxCLK+ LVDS differential clock input
19 VSS Ground
20 NC No Connection (Reserve)
LED CONVERTER
R0-R5, G0
G1~G5, B0, B1
B2-B5,HS,VS, DE
LVDS CLK
Version 2.0 21 December 2011 8 / 26
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
Page 9
PRODUCT SPECIFICATION
21 NC No Connection (Reserve)
22 VSS Ground
23 NC No Connection (Reserve)
24 NC No Connection (Reserve)
25 VSS Ground
26 NC No Connection (Reserve)
27 NC No Connection (Reserve)
28 VSS Ground
29 NC No Connection (Reserve)
30 NC No Connection (Reserve)
31 LED_GND LED Ground
32 LED_GND LED Ground
33 LED_GND LED Ground
34 NC No Connection (Reserve)
35 LED_PWM PWM Control Signal of LED Converter
36 LED_EN Enable Control Signal of LED Converter
37 NC No Connection (Reserve)
38 LED_VCCS LED Power Supply
39 LED_VCCS LED Power Supply
40 LED_VCCS LED Power Supply
Note (1) The first pixel is odd as shown in the following figure.
Version 2.0 21 December 2011 9 / 26
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
Page 10
PRODUCT SPECIFICATION
1,1
(odd)
2,1
3,1
1,2
(even)
2,2
1,3
(odd)
1,4
(even)
Pitch
1,Xmax
Pitch
Ymax,1
Ymax,
Xmax
4.2.2 LED CONVERTER OUTPUT PIN ASSIGNMENT
Pin Symbol Description Remark
1 NC No Connection (Reserve)
2 NC No Connection (Reserve)
3 LED1- LED Light Bar Feedback Channel
4
5
6
7 NC No Connection (Reserve)
8 LED+ LED Light Bar Input Power Supply
9 LED+ LED Light Bar Input Power Supply
10 LED+ LED Light Bar Input Power Supply
LED2LED3LED4-
LED Light Bar Feedback Channel
LED Light Bar Feedback Channel
LED Light Bar Feedback Channel
Version 2.0 21 December 2011 10 / 26
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
Page 11
PRODUCT SPECIFICATION
4.3 ELECTRICAL CHARACTERISTICS
4.3.1 LCD ELETRONICS SPECIFICATION
Parameter Symbol
Min. Typ. Max.
Power Supply V oltage VCCS 3.0 3.3 3.6 V (1)
Ripple Voltage VRP - 50 - mV (1)
Value
Unit Note
Inrush Current I
- - 1.5 A (1),(2)
RUSH
Mosaic - 250 280 mA (3)a
Power Supply Current
Black
lcc
- 270 300 mA (3)b
Note (1) The ambient temperature is Ta = 25 ± 2 ºC.
Note (2) I
: the maximum current when VCCS is rising
RUSH
I
: the maximum current of the first 100ms after power-on
IS
Measurement Conditions: Shown as the following figure. Test pattern: black.
+3.3V
Q1 2SK1475
VR1
R1
47K
Q2
2SK1470
C2
47K
R2
1K
0.01uF
(High to Low)
(Control Signal)
SW
+12V
C1
1uF
FUSE
C3
1uF
VCCS
(LCD Module Input)
VCCS rising time is 0.5ms
Version 2.0 21 December 2011 11 / 26
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
Page 12
PRODUCT SPECIFICATION
Note (3) The specified power supply current is under the conditions at VCCS = 3.3 V, Ta = 25 ± 2 ºC, DC
Current and f
a. Mosaic Pattern
= 60 Hz, whereas a power dissipation check pattern below is displayed.
v
b. Black Pattern
Active Area
Active Area
Version 2.0 21 December 2011 12 / 26
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
Page 13
PRODUCT SPECIFICATION
4.3.2 LED CONVERTER SPECIFICATION
Parameter Symbol
Value
Unit Note
Min. Typ. Max.
Converter Input power supply voltage
Converter Inrush Current
LED_Vccs
ILED
RUSH
6.0 12.0 21.0 V
- - 1.5 A (1)
Backlight On 3.0 - 3.6 V
EN Control Level
Backlight Off
0 - 0.5 V
PWM High Level 3.0 - 3.6 V
PWM Control Level
PWM Low Level
0 - 0.5 V
10 - 100 %
PWM Control Duty Ratio
5 - 100 % (2)
PWM Control Permissive Ripple
Voltage
PWM Control Frequency f
VPWM_pp
190 - 2K Hz (3)
PWM
- - 100 mV
LED Power Current LED_VCCS =Typ. ILED - 213 - mA (4)
Note (1) ILED
ILED
: the maximum current when LED_VCCS is rising,
RUSH
: the maximum current of the first 100ms after power-on,
IS
Measurement Conditions: Shown as the following figure. LED_VCCS = Typ, Ta = 25 ± 2 ºC, f
= 200 Hz, Duty=100%.
PWM
LED_VCCS(Typ)
Q1 IRL3303
VR1
R1
47K
R2
1K
47K
0.01uF
Q2
IRL3303
C2
(High to Low)
(Control Signal)
SW=24V
LED_VCCS(Typ)
C1
1uF
FUSE
C3
1uF
(LED Converter Input)
Version 2.0 21 December 2011 13 / 26
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
Page 14
PRODUCT SPECIFICATION
≤
∗
∗+≤
LED_VCC
LED_PWM
LED_EN
ILED
0V
0V
0V
ILED
VLED rising time is 0.5ms
0.5ms
90%
10%
Rush
100ms
ILED
IS
Note (2) If the PWM control duty ratio is less than 10%, there is some possibility that acoustic noise or
backlight flash can be found. And it is also difficult to control the brightness linearity.
Note (3) If PWM control frequency is applied in the range less than 1KHz, the “waterfall” phenomenon on
the screen may be found. To avoid the issue, it’s a suggestion that PWM control frequency should
follow the criterion as below.
PWM control frequency f
+ fN )33.0( f
should be in the range
PWM
fN
PWM
)66.0(
N : Integer )3( ≥N
f : Frame rate
Note (4) The specified LED power supply current is under the conditions at “LED_VCCS = Typ.”, Ta = 25
± 2 ºC, f
= 200 Hz, Duty=100%.
PWM
Version 2.0 21 December 2011 14 / 26
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
Page 15
PRODUCT SPECIFICATION
|
|
4.4 LVDS INPUT SIGNAL TIMING SPECIFICATIONS
4.4.1 LVDS DC SPECIFICATIONS
Parameter Symbol
Min. Typ. Max.
LVDS Differential Input High Threshold V
LVDS Differential Input Low Threshold V
LVDS Common Mode V oltage VCM 1.125 - 1.375 V (1)
LVDS Differential Input Voltage |VID| 100 - 600 mV (1)
L VDS Terminating Resistor RT 100 Ohm -
Note (1) The parameters of LVDS signals are defined as the following figures.
Single Ended
CM
V
0V
TH(LVDS)
-100 - - mV
TL(LVDS)
- - +100 mV
Value
Unit Note
V
CM
V
CM
VID|
(1),
=1.2V
(1)
=1.2V
Differential
4.4.2 LVDS DATA FORMAT
CLK+
Rxin2
Rxin1
Rxin0
T/7
IN20 IN19 IN18 IN17 IN16 IN15 IN14
DE B5 B4 B3 B2 Vsync Hsync
IN13 IN12 IN11 IN10 IN9 IN8 IN7
B1 G4 G3 G2 G1 B0 G5
IN6
G0 R3 R2 R1 R0
V
0V
V
IN5 IN4 IN3 IN2 IN1 IN0
R5
VID|
R4
Signal for 1 DCLK Cycle (T)
Version 2.0 21 December 2011 15 / 26
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
Page 16
PRODUCT SPECIFICATION
4.4.3 COLOR DATA INPUT ASSIGNMENT
The brightness of each primary color (red, green and blue) is based on the 6-bit gray scale data input
for the color. The higher the binary input the brighter the color. The table below provides the assignment
of color versus data input.
Data Signal
Color
R5 R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0
Black
Red
Green
Basic
Colors
Gray
Scale
Of
Red
Gray
Scale
Of
Green
Gray
Scale
Of
Blue
Note (1) 0: Low Level Voltage, 1: High Level Voltage
Blue
Cyan
Magenta
Yellow
White
Red(0)/Dark
Red(1)
Red(2)
:
:
Red(61)
Red(62)
Red(63)
Green(0)/Dark
Green(1)
Green(2)
:
:
Green(61)
Green(62)
Green(63)
Blue(0)/Dark
Blue(1)
Blue(2)
:
:
Blue(61)
Blue(62)
Blue(63)
0
1
0
0
0
1
1
1
0
0
0
:
:
1
1
1
0
0
0
:
:
0
0
0
0
0
0
:
:
0
0
0
Red Green Blue
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
1
1
1
0
1
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
0
0
0
0
0
1
1
1
1
0
1
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
0
0
0
1
1
1
0
1
0
0
0
:
:
0
0
0
0
0
0
:
:
0
0
0
0
1
0
:
:
1
0
1
Version 2.0 21 December 2011 16 / 26
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
Page 17
PRODUCT SPECIFICATION
4.5 DISPLAY TIMING SPECIFICATIONS
The input signal timing specifications are shown as the following table and timing diagram.
Signal Item Symbol Min. Typ. Max. Unit Note
DCLK Frequency 1/Tc 45 71 85 MHz -
Vertical Total Time TV 780 790 900 TH -
Vertical Active Display Period TVD 768 768 768 TH -
DE
Note (1) Because this module is operated by DE only mode, Hsync and Vsync are ignored.
DE
DCLK
DE
Vertical Active Blanking Period TVB TV-TVD 22 TV-TVD TH -
Horizontal Total Time TH 1408 1498 1800 Tc -
Horizontal Active Display Period THD 1366 1366 1366 Tc -
Horizontal Active Blanking Period THB
INPUT SIGNAL TIMING DIAGRAM
TC
TH-THD
T
HD
132
TH-THD
Tc -
DATA
Version 2.0 21 December 2011 17 / 26
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
Page 18
PRODUCT SPECIFICATION
4.6 POWER ON/OFF SEQUENCE
The power sequence specifications are shown as the following table and diagram.
Symbol
Min. Typ. Max.
t1 0.5 - 10 ms
t2 0 - 50 ms
t3 0 - 50 ms
t4 500 - - ms
t5 200 - - ms
t6 200 - - ms
t7 0.5 - 10 ms
tA 0.5 - 10 ms
tB 0 10 ms
tC 10 - - ms
tD 10 - - ms
tE 10 - - ms
tF 10 - - ms
Value
Unit Note
- Power Supply
for LCD, VCCS
- Interface Signal
(LVDS Signal of
Transmitter), VI
- Power Supply for
LED Converter,
LED_VCCS
- LED Converter
Dimming Signal,
LED_PWM
- LED Converter
Enable Signal,
LED_EN
0V
0V
0V
0V
0V
Power On
90%
10%
Power Off
t1
t2
Valid Data
t6 t5
90%
10%
tA
tC
PWM Signal
tE t
90%
tB
t
D
F
90%
10%
t3
t7
10%
10%
t4
Note (1) Please don’t plug or unplug the interface cable when system is turned on.
Note (2) Please avoid floating state of the interface signal during signal invalid period.
Note (3) It is recommended that the backlight power must be turned on after the power supply for LCD and the
interface signal is valid.
Version 2.0 21 December 2011 18 / 26
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
Page 19
PRODUCT SPECIFICATION
5. OPTICAL CHARACTERISTICS
5.1 TEST CONDITIONS
Item Symbol Value Unit
Ambient Temperature T a
Ambient Humidity Ha
25±2
50±10
Supply Volt age VCC 3.3 V
Input Signal According to typical value in "3. ELECTRICAL CHARACTERISTICS"
The measurement methods of optical characteristics are shown in Section 5.2. The following items
should be measured under the test conditions described in Section 5.1 and stable environment shown in
Note (5).
5.2 OPTICAL SPECIFICATIONS
Item Symbol Condition Min. Typ. Max. Unit Note
Contrast Ratio CR 500 600 - - (2), (3)
Response Time
Red
Color
Chromaticity
Green
Blue
White
Horizontal
Viewing Angle
Vertical
Note (0) Light source is the standard light source “C” which is defined by CIE and driving voltages are
TR - 3 8 ms
T
- 8 13 ms
F
Rx
Ry
Gx
Gy
Bx
By
θ
=0°, θY =0°
x
Viewing Normal Angle
Standard light source
“C”
Typ –
0.03
0.589
0.336
0.286
0.546
0.158
0.169
Typ +
0.03
Wx 0.313 Wy
θ
x
θ
x
θ
Y
θ
Y
+
+
40 45
CR≥10
-
40 45 15 20 40 45 -
0.329
o
C
%RH
(4)
-
-
(0),(2),
-
(5),(6)
-
-
-
Deg. (2), (5)
based on suitable gamma voltages. The calculating method is as following：
1. Measure Module’s and BLU’s spectrums. White is without signal input and R, G, B are with
signal input. BLU is supplied by CMI.
2. Calculate cell’s spectrum.
3. Calculate cell’s chromaticity by using the spectrum of standard ligh t source “C”
Version 2.0 21 December 2011 19 / 26
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
Page 20
PRODUCT SPECIFICATION
.67 ms
Note (1) Light source is the BLU which is supplied by CMO and driving voltages are based on suitable
gamma voltages. White is without signal input and R, G, B are with signal input. SPEC is judged
by CMO’s golden sample.
Note (2) Definition of Viewing Angle (θx, θy):
θX- = 90º
x-
6 o’clock
θ
y- = 90º
y-
Note (3) Definition of Contrast Ratio (CR):
The contrast ratio can be calculated by the following expression.
Contrast Ratio (CR) = L63 / L0
L63: Luminance of gray level 63
Normal
θx = θy = 0º
θy- θy+
θx−
θx+
y+
12 o’clock direction
θ
y+ = 90º
x+
θX+ = 90º
L 0: Luminance of gray level 0
CR = CR (1)
CR (X) is corresponding to the Contrast Ratio of the point X at Figure in Note (6).
Note (4) Definition of Response Time (T
, TF):
R
100%
90%
Optical
Response
10%
0%
Time
T
66
F
T
R
66.67 ms
Version 2.0 21 December 2011 20 / 26
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
Page 21
Note (5) Measurement Setup:
500
The LCD module should be stabilized at given temperature for 20 minutes to avoid abrupt
temperature change during measuring. In order to stabilize the luminance, the measurement
should be executed after lighting Backlight for 20 minutes in a windless room.
PRODUCT SPECIFICATION
Note (6) The listed optical specifications refer to the initial value of manufacture, but the condition of
LCD Module
LCD Panel
USB2000
CS-2000T
Field of View = 2º
Center of the Screen
mm
Light Shield Room
(Ambient Luminance < 2 lux)
the specifications after long-term operation will not be warranted.
Version 2.0 21 December 2011 21 / 26
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
Page 22
6. PACKING
6.1 CMI OPEN CELL LABEL
The barcode nameplate is pasted on each OPEN CELL as illustration for CMI internal control.
PRODUCT SPECIFICATION
Made in XXXX
N140B6-P21
(a) Model Name: N140B6 - P21
(b) Revision: Rev. XX, for example: C1, C2 …etc.
(c) Serial ID: X X
Serial ID includes the information as below:
(a) Manufactured Date: Year: 0~9, for 2010~2019
XXXXXXXYMDLNNNN
X X X X X Y M D L N N N N
Rev. XX
Rev. XX
Serial No.
Product Line
Year, Month, Date
CMI Internal Use
Revision
CMI Internal Use
Month: 1~9, A~C, for Jan. ~ De c.
Day: 1~9, A~Y, for 1
(b) Revision Code: cover all the change
(c) Serial No.: Manufacturing sequence of product
(d) Product Line: 1 -> Line1, 2 -> Lin e 2, …etc.
st
to 31st, exclude I , O and U
Version 2.0 21 December 2011 22 / 26
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
Page 23
PRODUCT SPECIFICATION
6.2 Package Reliability
(1) Carton Packing should have no failure in the following reliability test items
Test Item Test Conditions Note
ISTA STANDARD
Packing
Vibration
6.3 CARTON
Random, Frequency Range: 1 – 200 Hz
Top & Bottom: 30 minutes (+Z), 10 min (-Z),
Right & Left: 10 minutes (X)
Back & Forth 10 minutes (Y)
Non Operation
Figure. 6-3 Packing method
Version 2.0 21 December 2011 23 / 26
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
Page 24
6.4 PALLET
PRODUCT SPECIFICATION
Figure. 6-4 Packing method
Version 2.0 21 December 2011 24 / 26
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
Page 25
PRODUCT SPECIFICATION
7. PRECAUTIONS
7.1 HANDLING PRECAUTIONS
(1) The module should be assembled into the system firmly by using every mounting hole. Be careful
not to twist or bend the module.
(2) While assembling or installing modules, it can only be in the clean area. The dust and oil may cause
electrical short or damage the polarizer.
(3) Use fingerstalls or soft gloves in order to keep display clean during the incoming inspection and
assembly process.
(4) Do not press or scratch the surface harder than a HB pencil lead on the panel because the polarizer
is very soft and easily scratched.
(5) If the surface of the polarizer is dirty, please clean it by some absorbent cotton or soft cloth. Do not
use Ketone type materials (ex. Acetone), Ethyl alcohol, Toluene, Ethyl acid or Methyl chloride. It
might permanently damage the polarizer due to chemical reaction.
(6) Wipe off water droplets or oil immediately. Staining and discoloration may occur if they left on panel
for a long time.
(7) If the liquid crystal material leaks from the panel, it should be kept away from the eyes or mouth. In
case of contacting with hands, legs or clothes, it must be washed away thoroughly with soap.
(8) Protect the module from static electricity, it may cause damage to the C-MOS Gate Array IC.
(9) Do not disassemble the module.
(10) Do not pull or fold the LED wire.
(11) Pins of I/F connector should not be touched directly with bare hands.
7.2 STORAGE PRECAUTIONS
(1) High temperature or humidity may reduce the performance of module. Please store LCD module
within the specified storage conditions.
(2) It is dangerous that moisture come into or contacted the LCD module, because the moisture may
damage LCD module when it is operating.
(3) It may reduce the display quality if the ambient temperature is lower than 10 ºC. For example, the
response time will become slowly, and the starting voltage of LED will be higher than the room
temperature.
7.3 OPERATION PRECAUTIONS
(1) Do not pull the I/F connector in or out while the module is operating.
(2) Always follow the correct power on/off sequence when LCD module is connecting and operating.
This can prevent the CMOS LSI chips from damage during latch-up.
(3) The startup voltage of Backlight is approximately 1000 Volts. It may cause electrical shock while
assembling with converter . Do not disassemble the module or insert anything into the Backlight unit.
Version 2.0 21 December 2011 25 / 26
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
Page 26
Appendix. OUTLINE DRAWING
PRODUCT SPECIFICATION
Version 2.0 21 December 2011 26 / 26
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
Loading...