chimei N173O6 - L02 Datasheet
Issued Date: Feb. 20, 2009
Model No.: N173O6 - L02
Approval
TFT LCD Approval Specification
MODEL NO.: N173O6 - L02
Customer : HP
Approved by :
Note :
22:07:04 CST
記錄 工作 審核 角色 投票
2009-02-25
PMMD III
Director
annie_hsu(徐凡琇
Director Accept
/56522 / 54873)
1 / 29
Version 3.0
Issued Date: Feb. 20, 2009
Model No.: N173O6 - L02
Approval
- CONTENTS –
REVISION HISTORY
1. GENERAL DESCRIPTION
1.1 OVERVIEW
1.2 FEATURES
1.3 APPLICATION
1.4 GENERAL SPECIFICATIONS
1.5 MECHANICAL SPECIFICATIONS
2. ABSOLUTE MAXIMUM RATINGS
2.1 ABSOLUTE RATINGS OF ENVIRONMENT
2.2 ELECTRICAL ABSOLUTE RATINGS
2.2.1 TFT LCD MODULE
2.2.2 BACKLIGHT UNIT
3. ELECTRICAL CHARACTERISTICS
3.1 TFT LCD MODULE
3.2 BACKLIGHT UNIT
4. BLOCK DIAGRAM
4.1 TFT LCD MODULE
5. INPUT TERMINAL PIN ASSIGNMENT
5.1 TFT LCD MODULE
5.2 TIMING DIAGRAM OF LVDS INPUT SIGNAL
5.3 COLOR DAT A INPUT ASSIGNMENT
5.4 EDID CODE DATA STRUCTURE
6. Inverter Specification ------------------------------------------------------- 17
6.1 ABSOLUTE MAXIMUM RATINGS
6.2 RECOMMENDED OPERATING RATINGS
6.3 LED BACKLIGHT CONTROLL POWER SEQUENCE
7. INTERFACE TIMING
7.1 INPUT SIGNAL TIMING SPECIFICATIONS
7.2 POWER ON/OFF SEQUENCE
8. OPTICAL CHARACTERISTICS
8.1 TEST CONDITIONS
8.2 OPTICAL SPECIFICATIONS
9. PRECAUTIONS
9.1 ASSEMBL Y AND HANDLING PRECAUTIONS
9.2 SAFETY PRECAUTIONS
10. PACKING
10.1CARTON
10.2 PALLET
11. DEFINITION OF LABELS
11.1 CMO MODULE LABEL
11.2
CMO CARTON LABEL
------------------------------------------------------- 3
------------------------------------------------------- 4
------------------------------------------------------- 5
------------------------------------------------------- 7
------------------------------------------------------- 10
------------------------------------------------------- 11
------------------------------------------------------- 18
------------------------------------------------------- 20
------------------------------------------------------- 24
------------------------------------------------------- 25
------------------------------------------------------- 27
2 / 29
Version 3.0
Issued Date: Feb. 20, 2009
Model No.: N173O6 - L02
Approval
Version Date
Ver. 3.0
Feb.20, ‘09 All All Approval Specification was first issued.
Page
(New)
REVISION HISTORY
Section Description
3 / 29
Version 3.0
Issued Date: Feb. 20, 2009
Model No.: N173O6 - L02
1. GENERAL DESCRIPTION
1.1 OVERVIEW
N173O6 - L02 is a 17.3” TFT Liquid Crystal Display module with LED Backlight unit and 40 pins LVDS
interface. This module supports 1600 x 900 HD+ mode and can display 262,144 colors. The optimum
viewing angle is at 6 o’clock direction. The inverter module for Backlight is built in.
1.2
FEATURES
- HD+ (1600 x 900 pixels) resolution
- DE only mode
- 3.3V LVDS (Low Voltage Differential Signaling) interface with 2 pixel/clock
- LED
1.3 APPLICA TION
Approval
- TFT LCD Notebook
1.4 GENERAL SPECIFICATI0NS
Item Specification Unit Note
Active Area 382.08 (H) x 214.92 (V) (17.3” diagonal) mm
Bezel Opening Area 386.88 (H) x 218.32 (V) mm
Driver Element a-si TFT active matrix - Pixel Number 1600 x R.G.B. x 900 pixel Pixel Pitch 0.2388 (H) x 0.2388(V) mm Pixel Arrange ment RGB vertical stripe - Display Colors 262,144 color Transmissive Mode Normally white - Surface Treat ment Hard coating (3H), Glare Type - -
1.5 MECHANICAL SPECIFICATIONS
Item Min. Typ. Max. Unit Note
Horizontal (H) 397.6 398.1 398.6 mm
Module Size
Note (1) Please refer to the attached drawings for more information of front and back outline dimensions.
Vertical (V) 232.3 232.8 233.3 mm
Depth (D) 5.5 5.8 mm
Weight 525 540 g
(1)
(1)
4 / 29
Version 3.0
Issued Date: Feb. 20, 2009
A
Model No.: N173O6 - L02
Approval
2. ABSOLUTE MAXIMUM RATINGS
2.1 ABSOLUTE RATINGS OF ENVIRONMENT
Item Symbol
Storage Temperature TST -20 +60 ºC (1)
Operating Ambient T emperature TOP 0 +50 ºC (1), (2)
Shock (Non-Operating) S
Vibration (Non-Operating) V
Note (1) (a) 90 %RH Max. (Ta ≦ 40 ºC).
(b) Wet-bulb temperature should be 39 ºC Max. (Ta > 40 ºC).
(c) No condensation.
Note (2) The temperature of panel display surface area should be 0 ºC Min. and 60 ºC Max.
- 220/2 G/ms (3), (5)
NOP
- 1.5 G (4), (5)
NOP
Min. Max.
Relative Humidity (%RH)
100
90
Value
Unit Note
80
60
Operating Range
40
20
10
Storage Range
80 60 -20 40 0 20 -40
Temperature (ºC)
Note (3) 1 time for ± X, ± Y, ± Z. for Condition (220G / 2ms) is half Sine Wave,.
Note (4) 10 ~ 500 Hz, 30 min/cycle,1cycles for each X, Y, Z axis.
Note (5) At testing Vibration and Shock, the fixture in holding the module has to be hard and rigid
enough so that the module would not be twisted or bent by the fixture.
The fixing condition is shown as below:
t Room Temperature
Side Mount Fixing Screw
Gap=2mm
Bracket
LCD Module
Side Mount Fixing Screw
Stage
5 / 29
Version 3.0
2.2 ELECTRICAL ABSOLUTE RATINGS
2.2.1 TFT LCD MODULE
Item Symbol
Power Supply V oltage VCC -0.3 +4.0 V
Logic Input Voltage VIN -0.3 VCC+0.3 V
Min. Max.
Value
2.2.2 BACKLIGHT UNIT
Item Symbol
LED Light Bar Power Supply
Voltage
LED Light Bar Power Supply
Current
Min. Max.
-40 28 V
V
L
I
0 200 mA
L
Value
Issued Date: Feb. 20, 2009
Model No.: N173O6 - L02
Approval
Unit Note
(1)
Unit Note
(1), (2)
Note (1) Permanent damage to the device may occur if maximum values are exceeded. Function operation
should be restricted to the conditions described under Normal Operating Co nditions.
Note (2) Specified values are for L E D (Refer to 3.2 for further information).
6 / 29
Version 3.0
Issued Date: Feb. 20, 2009
Model No.: N173O6 - L02
Approval
3. ELECTRICAL CHARACTERISTICS
3.1 TFT LCD MODULE
Parameter Symbol
Min. Typ. Max.
Power Supply V oltage Vcc 3.0 3.3 3.6 V Permissive Ripple Voltage VRP 50 mV Rush Current I
1.5 A (2)
RUSH
Initial Stage Current IIS 1.0 A (2)
Power Supply Current
White 240 260 300 mA (3)a
Black
LVDS Differential Input High Threshold V
LVDS Differential Input Low Threshold V
TH(LVDS)
TL(LVDS)
330 350 390 mA (3)b
+100 mV
-100 mV
LVDS Common Mode Voltage VCM 1.125 1.375 V (5)
LVDS Differential Input Voltage |VID| 100 600 mV (5)
Terminating Resistor RT 100 Ohm
Power per EBL WG P
- 2.02 - W (4)
EBL
Note (1) The ambient temperature is Ta = 25 ± 2 ºC.
Value
Unit Note
V
CM
V
CM
(5),
=1.2V
(5)
=1.2V
Note (2) I
I
: the maximum current when VCC is rising
RUSH
: the maximum current of the first 100ms after power-on
IS
Measurement Conditions: Shown as the following figure. Test pattern: black.
(High to Low)
(Control Signal)
SW
+12V
C1
1uF
+3.3V
VR1
R1
47K
R2
1K
47K
Q1 2SK1475
FUSE
Q2
2SK1470
C2
0.01uF
Vcc rising time is 470us
0.9Vcc
0V
470us
0.1Vcc
+3.3V
100ms
I
RUSH
C3
1uF
Vcc
(LCD Module Input)
VCC
I
IS
ICC
7 / 29
Version 3.0
Issued Date: Feb. 20, 2009
|
|
Model No.: N173O6 - L02
Note (3) The specified power supply current is under the conditions at Vcc = 3.3 V, Ta = 25 ± 2 ºC, fv = 60
Hz, whereas a power dissipation check pattern below is displayed.
Approval
Note (4) The specified power are the sum of LCD panel electronics input power and the inverter input
Note (5) The parameters of LVDS signals are defined as the following figures.
a. White Pattern
Active Area
power. Test conditions are as follows.
(a) Vcc = 3.3 V, Ta = 25 ± 2 ºC, f
(b) The pattern used is a black and white 32 x 36 checkerboard, slide #100 from the VESA file
“Flat Panel Display Monitor Setup Patterns”, FPDMSU.ppt.
(c) Luminance: 60 nits.
= 60 Hz,
v
b. Black Pattern
Active Area
CM
Single Ended
Differential
V
0V
V
0V
V
VID|
VID|
8 / 29
Version 3.0
Issued Date: Feb. 20, 2009
Model No.: N173O6 - L02
Approval
3.2 BACKLIGHT UNIT Ta = 25 ± 2 ºC
Parameter Symbol
LED Light Bar Power
Supply Volt age
LED Light Bar Power
Supply Current
V
22.4 25.6 28 V
L
I
-- 140 200 mA
L
Min. Typ. Max.
Power Consumption PL -- 3.58 -- W
LED Life Time LBL 15000 - - Hrs (4)
Note (1) LED light bar configuration is shown as below.
Value
Unit Note
(1),(2) (Duty 100%)
(3),I
=140mA
L
(Duty 100%)
Note (2) For better LED light bar driving quality, it is recommended to utilize the adaptive boost converter with current
balancing function to drive LED light-bar.
Note (3) P
Note (4) The lifetime of LED is defined as the time when it continues to operate under the cond itions at Ta = 25 ±2
= IL ×VL
L
= 20 mA(Per EA) until the brightness becomes ≦ 50% of its original value.
and I
L
o
C
9 / 29
Version 3.0
Loading...