Child Craft 15061, 16101, 16151, 16191, 16281 User Manual

Download

Page 1

CCH00701:09/00 JCHE p65

DOUBLE DROPSIDE CRIB

child craftchild craft

child craft

CHILD CRAFT INDUSTRIES, INC.

P.O. Box 444, Salem, IN USA 47167-0444

PH: 812-883-3111 - FAX: 812-883-1819 - http://www.childcraftind.com

ASSEMBLY DIRECTIONS AND PARTS LIST

ΦREAD ALL INSTRUCTIONS WITH CARE BEFORE STARTING THE ASSEMBLY PROCEDURE. ΦΦ

ΦΦ

ΦYOU WILL NEED A #2 PHILLIPS SCREWDRIVER, A SLOTTED SCREWDRIVER AND A HAMMER.

PARTS ENCLOSED IN HARDWARE BAG (NOTED WHEN SHOWN ACTUAL SIZE)

(18) Slotted/Phillips

Wood Screws

(12) Slotted/Phillips

Machine Screws

(actual size)

(4) Spring Hangers

(4) Gate Shoes

(2)

Moulded

plastic

backers

(2)

4-Position

Spring

Hanger

Brackets

(actual size)

(4) Compression

Springs

(4) Bumper

Springs

(4) Casters

(style may vary)

(2) Angle

Brackets

PARTS INCLUDED IN CARTON

(1) Footboard

(1) Headboard

P &

(2) Crib sides

(Dropsides)

(1) Spring

(2) Stabilizer Bars

(4) Crib Rods

PREPARATION

Carefully remove and lay out all hardware and parts. Remove wires securing the (2) Stabilizer Bars

J and the (4) Crib Rods

K to Crib Spring

R. Check

quantities and match to the three Parts Lists above. If any part is missing or broken contact your dealer or Child Craft (P.O. Box 444, Salem, IN 471670444 USA (ph# 812/883-3111), [email protected] for a replacement part or instructional literature. Before making this contact, identify your crib. A model identification number is stamped on the underneath side of the bottom rail of either a crib end

O or a crib side

Q. Record the model

Identification Number now: # ______________________. Include this number with a request for a part or instructional literature. DO NOT SUBSTITUTE PARTS!

Note the two piece assembly of 4-Position Spring Hanger Brackets

D. Before

attachment to crib

(ends)

N &O, check to be sure the moulded plastic backer

aligns with the 4-Position Spring Hanger Bracket

D as shown. These items are

shipped assembled, in the unlikely event they should become detached during shipment, simply take the plastic backer, align with the holes in the metal bracket and snap together to create an assembly as shown in the Hardware Parts Diagram. IMPORTANT! All four plastic tabs on each moulded plastic backer should project toward the metal hooks on 4-Position Spring Hanger Brackets

D. If you should

find a tab on an uninstalled 4-Position Spring Hanger Bracket not so projected, simply use a screwdriver to push tab forward until it contacts the metal hook. If a plastic tab is not projected on a factory installed 4-Position Spring Hanger Bracket simply place a small slotted screwdriver underneath the plastic tab and pull forward until it contacts the metal hook. Attach a 4-Position Spring Hanger Bracket

(2 piece assembly)

, to both Headboard

N & Footboard

O with Slotted/Phillips

Wood Screws

E, to be positioned exactly as the ones already factory installed.

Attach Angle Brackets

I with Slotted/Phillips Wood Screws

E to Headboard

and Footboard

O, to be positioned exactly as the ones already factory installed.DO

NOT REMOVE 4-POSITION SPRING HANGER BRACKETS OR ANY OTHER HARDWARE ITEM ATTACHED WITH SLOTTED/PHILLIPS WOOD SCREWS

STEP 1 - DIAGRAM 1: ATTACH OF 4-POSITION SPRING HANGER BRACKETS AND ANGLE BRACKETS.

Factory installed

Holes to receive Slotted/ Phillips Wood Screws

15061,16101,16151,16191,16281

Page 2

STEP 2 - DIAGRAM 2: INSTALL STABILIZER BARS.

Attach each Stabilizer Bar DIAGRAM 6. You will use a total of (8) Slotted/Phillips Machine Screws Slotted/Phillips Machine Screw

Bar

J placement, located in ends

- do not tighten at this time. Place the keyhole (top hole in each end of Stabilizer Bar

J, over top extended Screws

to Diagram. Ends this procedure for mounting the remaining Stabilizer Bar in the exact same manner. Place four Slotted/Phillips Machine Screws receiving holes in each end of both Stabilizer Bars

ends

N &

O, tighten all eight Slotted/Phillips Machine Screws

N and

J to crib ends

A into top receiving bushing, designated for Stabilizer

O &

(which you have just installed and left extended),

O will now be mounted together on one side of crib, repeat

N and

O. Refer to Diagram 2 and MAIN

N as shown, leave each top screw extended

J to the other side of the crib

J, into receiving bushings located in

A securely at this time.

A. Place a

refer

A into the lower

STEP 3 - DIAGRAM 3: ATTACH GATE SHOES TO DROPSIDES.

C to lower rail

C over predrilled lead holes on lower rail

and affix with (8) Slotted/Phillips Wood Screws

C. Tighten Screws

(inside)

of each Crib Side

E securely. Note: When

Position two Gate Shoes shown. Note: Gate Shoe Patent No. will be visible when Gate Shoes mounted. Align Gate Shoes of Crib Side

E, two in each Gate Shoe

disassembling crib in the future, DO NOT REMOVE THE GATE SHOES ANY OTHER HARDWARE ITEM ATTACHED WITH SLOTTED/PHILLIPS WOOD SCREWS

P/QP/Q

P/Q

P/QP/Q

(dropsides)

P/QP/Q

P/Q as

P/QP/Q

C are

(inside)

C OR

Extended

Factory installed

CCH00701:09/00

Keyhole

P orQ

STEP 4 - DIAGRAM 4: INSTALL SPRING HANGERS & CRIB SPRING

Locate Crib Spring Spring Hangers side of Crib Spring

6. Also the printing on the plastic pouch placed upward. Insert Spring Hangers frame of Crib Spring required to fully engage Spring Hangers

R by placing each of the 4 Spring Hanger

of the four 4-Position Spring Hanger Brackets backers), mounted on ends The lip of the moulded plastic backer will allow the Spring Hanger to be placed with no difficulty. However, when you decide on another placement of Crib Spring screwdriver, on the lip of the moulded plastic backer and hold down in order to raise Spring Hanger procedure whenever you opt to change Crib Spring four positions.

(with plastic pouch factory attached)

B, refer to Main Diagram 6, and 4. Note: Be sure smooth

R wire is placed upward as illustrated in Main Diagram

R as shown, (a light blow with a hammer may be

O and

R you will need to place your thumbnail, or a small

B from its present position. Follow this same

(attached to crib spring)

B into each bracket attached to

B). Carefully install Crib Spring

B into a selected position in each

D, (with moulded plastic

N. See Main Diagram 6, and 4. Note:

, and the four

R to another of the

STEP 5: INSTALL CRIB DROPSIDES

Locate Crib Rods Springs a Crib Rod

to Main Diagram 6 for proper placement.)

G and the four remaining Slotted/Phillips Machine Screws

1.1.

1. The top rail of Crib Side

1.1.

K, Crib Sides

K downward through the holes in the following sequence:

(Note: gate shoes will be placed to inside),

2.2.

2. The L- bracket on 4-Position Spring Hanger Bracket

2.2.

3.3.

3. Compression Spring

3.3.

4.4.

4. Bottom Rail of Crib Side

4.4.

5.5.

5. A Bumper Spring

5.5.

6.6.

6. Hole in Angle Bracket

6.6.

P/QP/Q

P/Q, Compression Springs

P/QP/Q

P or

(with plastic teething rail),

P or

F, Bumper

will be

A. Insert

(Refer

Top surface

To remove Spring Hanger down on lip with thumbnail or screwdriver and pull Spring Hanger

Place a Slotted/Phillips Machine Screw and into receiving bushing located in top corner post of Footboard Headboard

USE A POWER SCREWDRIVER OF ANY TYPE TO TIGHTEN SCREW

Start Screw A (two or three turns) with your fingers into its threaded bushing to insure Screw A has a square fit. Once you are sure Screw A fits squarely into its threaded bushing, tighten securely with a hand held screwdriver. Attach the other Crib Rod Side Machine Screws tighten if needed. suggest you rub the crib rod with waxed paper or paraffin. You may want

to repeat this procedure periodically. Attach the remaining Crib Side or

B press

B upward.

. Refer

to Main Diagram 6 for proper placement. DO NOT

P or

Q,, using the same procedure. Be sure Slotted/Phillips

A are tightened securely, check periodically and

Tip:Tip:

Tip: To help Crib Rods

Tip:Tip:

Q, by repeating Step 5.

A into hole in top of Crib Rod

K to the other end of Crib

K function more quietly we

CLOSE UPCLOSE UP

CLOSE UP

CLOSE UPCLOSE UP VIEW VIEW

VIEW

VIEW VIEW

Page 3

CCH00701:09/00

MAIN DIAGRAM 6

TIGHTEN SCREW

A MANUALLY, DO NOT USE ANY TYPE OF POWER SCREWDRIVER.

N A

P / Q

Top rail

Locate the 4 Casters lower corner post of Headboard

O. Refer to Main Diagram 6.

design may possibly vary according to your particular crib model.)

CAUTION:

ally thick carpet, take care when crib is rolled as Casters carpet pile and possibly cause breakage or damage to lower corner posts of crib.

If crib is placed on exception-

H, insert each into a

could catch on thick

N/Footboard

(Caster

Plastic pouch

Hook end

CRIB SPRING

Be sure the smooth side of wire is placed up as illustrated. Also,style of Crib Spring your model of crib.

R may differ with

down

Foot latch

P / Q

Bottom rail

CLOSE UP VIEW

F G

I H

Permanent Storage of Assembly Instructions: After completing the assembly process you are advised to read and be aware of all WARNINGS, CAUTIONS, CLEANING, STORAGE, USE, and MAINTENANCE notices contained in this set of assembly directions and printed on the plastic pouch located on the underneath side of crib spring. You will then place this complete set of assembly directions into the plastic pouch for future referral. We caution you not to place excess hardware in the plastic pouch as it could present danger to a small child if retrieved.

Place a purchased mattress on Crib Spring

R and crib is ready for use.

TO RAISE & LOWER CRIB DROPSIDE: To lower lift the dropside slightly, push the foot latch toward the inside of crib which will release the dropside to the lowest or "DOWN" position. To raise the dropside, lift up on the dropside, rail will then lock into the "UP" position.

N/O Corner Post

Page 4

ARNINGARNING

ARNING

▲

ΦΦ

ΦFAILURE TO FOLLOW THESE WARNINGS AND ASSEM-

ΦΦ

ARNINGARNING

CCH00701:09/00

BLY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.

ΦΦ

ΦREAD ALL INSTRUCTIONS BEFORE ASSEMBLING CRIB.

ΦΦ

KEEP INSTRUCTIONS FOR FUTURE USE. A plastic pouch is attached to crib spring for permanent storage of the instructional literature.

ΦΦ

ΦBEFORE EACH USAGE OR ASSEMBLY, INSPECT CRIB

ΦΦ

FOR DAMAGED HARDWARE, LOOSE JOINTS, MISSING PARTS OR SHARP EDGES. DO NOT USE CRIB IF ANY PARTS ARE MISSING OR BROKEN. ASK YOUR DEALER OR CHILD CRAFT, P.O. BOX 444, SALEM, IN 47167-0444 USA (812/883-3111) [email protected] FOR REPLACEMENT PARTS AND INSTRUCTIONAL LITERATURE IF NEEDED. INCLUDE MODEL IDENTIFICATION NUMBERS WITH YOUR REQUEST WHICH YOU RECORDED ON PAGE ONE. DO NOT SUBSTITUTE PARTS.

ΦΦ

ΦAFTER RAISING SIDE, MAKE SURE LATCHES ARE SE-

ΦΦ

CURE.

ΦΦ

ΦWHEN CHILD IS ABLE TO CLIMB OUT OR REACHES THE

ΦΦ

HEIGHT OF 35 INCHES (90 CENTIMETERS) THE CRIB SHALL NO LONGER BE USED.

ΦΦ

ΦDO NOT PLACE CRIB NEAR WINDOW WHERE CORDS

ΦΦ

FROM BLINDS OR DRAPES MAY STRANGLE A CHILD.

ΦΦ

ΦIF REFINISHING, USE A NON-TOXIC FINISH SPECIFIED

ΦΦ

FOR CHILDREN'S PRODUCTS.

ΦΦ

ΦDO NOT LEAVE CHILD IN CRIB WITH SIDE LOWERED. BE

ΦΦ

SURE SIDE IS IN RAISED AND LOCKED POSITION WHENEVER CHILD IS IN CRIB.

ΦΦ

ΦWHEN CHILD IS ABLE TO PULL TO STANDING POSITION,

ΦΦ

SET MATTRESS TO LOWEST POSITION AND REMOVE BUMPER PADS, LARGE TOYS AND OTHER OBJECTS THAT COULD SERVE AS STEPS FOR CLIMBING OUT.

ΦΦ

ΦNEVER USE PLASTIC SHIPPING BAGS OR OTHER PLAS-

ΦΦ

TIC FILM AS MATTRESS COVERS BECAUSE THEY CAN CAUSE SUFFOCATION.

ΦΦ

ΦDO NOT USE A WATER MATTRESS WITH THIS CRIB.

ΦΦ ΦΦ

ΦREPLACE TEETHING RAIL(S) IF DAMAGED OR LOOSE.

ΦΦ ΦΦ

ΦSTRINGS CAN CAUSE STRANGULATION! DO NOT PLACE

ΦΦ

ITEMS WITH A STRING AROUND A CHILD'S NECK, SUCH AS HOOD STRINGS OR PACIFIER CORDS. DO NOT SUSPEND STRINGS OVER A CRIB OR ATTACH STRINGS TO TOYS.

ΦΦ

ΦREMOVE ALL CRIB TOYS WHICH ARE STRUNG ACROSS

ΦΦ

CRIB AREA WHEN YOUR CHILD IS BEGINNING TO PUSH UP ON HANDS AND KNEES OR IS 5 MONTHS OF AGE, WHICHEVER OCCURS EARLIEST. THESE TOYS CAN CAUSE STRANGULATION!

CAUTIONCAUTION

CAUTION

CAUTIONCAUTION

ΦΦ

ΦANY MATTRESS USED IN THIS

ΦΦ

CRIB MUST BE AT LEAST 27-1/4 INCHES (69 CENTIMETERS), BY 515/8 INCHES (131 CENTIMETERS), WITH A THICKNESS NOT EXCEEDING 6 INCHES (15 CENTIMETERS). the dimensions of the mattress shall be taken from seam to seam or edge to edge where appropriate.

ΦΦ

ΦUPON COMPLETION OF ASSEM-

ΦΦ

BLY BE SURE ALL SCREWS, BOLTS AND FASTENING DEVICES HAVE BEEN TIGHTENED SECURELY. A FREQUENT CHECK SHOULD BE MADE OF ALL SCREWS, BOLTS AND FASTENING DEVICES AND TIGHTEN IF NEEDED.

MAINTENANCE OF YOUR CHILD CRAFT CRIB:

completion of assembly be sure all screws, bolts and fastening devices have been tightened securely. A frequent periodic check should be made of all screws, bolts and fastening devices and tighten if needed. Before each usage or assembly, inspect crib for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use crib if parts are missing or broken. Ask your Dealer or Child Craft (812/883-3111), [email protected] for replacement parts and instructional literature if needed. Include Model Identification Number with your request which you recorded on page 1. DO NOT substitute parts. DO NOT make any alteration to this crib.

CLEANING INSTRUCTIONS FOR YOUR CHILD CRAFT CRIB:

Mix together a mild solution of gentle dishwashing liquid and water, apply to crib surface using a soft clean cloth lightly dampened in the solution. Rinse with clear water again using a soft clean cloth then dry all surfaces thoroughly with a soft dry cloth. NO ABRASIVE CLEAN- ERS, SCOURING PADS, STEEL WOOL, OR COARSE RAGS SHOULD BE USED TO CLEAN THIS FINE FURNITURE.

STORAGE AND USE OF YOUR CHILD CRAFT CRIB:

printed plastic pouch is attached to the crib spring for the permanent storage of the assembly directions. After completing the assembly process you are advised to read and be aware of all WARNINGS, CAUTIONS, CLEANING, STORAGE, USE AND MAINTENANCE notices contained in this set of assembly directions and printed on the plastic pouch located on the underneath side of crib spring. You will then place the complete set of assembly directions into the plastic pouch for future referral. We caution you not to place excess hardware in the plastic pouch as it could present danger to a child if retrieved and it could also puncture crib mattress. When storing crib use CAUTION as extreme temperature or humidity changes could be harmful. Use CAUTION when a vaporizer is in use, always aim vaporstream away from crib as well as away from any other wood furniture item.

Upon

CCH00701:09/00 JCHE p65

made in usa

ΦΦ

ΦWHEN DISASSEMBLING THIS CRIB, DO NOT REMOVE

ΦΦ

ANY ITEM ATTACHED WITH WOOD SCREWS.

ΦΦ

ΦALWAYS ENSURE A SAFE ENVIRONMENT FOR THE

ΦΦ

CHILD BY CHECKING REGULARLY, BEFORE PLACING THE CHILD IN THE CRIB, THAT EVERY COMPONENT IS PROPERLY AND SECURELY IN PLACE.

CHILD CRAFT INDUSTRIES, INC.

P.O. Box 444, Salem, IN USA 47167-0444

PH: 812-883-3111 - FAX: 812-883-1819

http://www.childcraftind.com