Childcare Ezi Feeder 043052 User Manual
Ezi Feed
2-in-1 Booster
Model # 043052
IMPORTANT: RETAIN FOR FUTURE REFERENCE, READ CAREFULLY
SAFETY PRECAUTIONS
Read all instructions before assembly and use of the seat. Keep instructions for future use.
WARNING
• NEVER leave the child unattended.
• ALWAYS use the restraint system and ensure it is correctly tted.
• ALWAYS use the chair attachment system and ensure it is correctly tted before use.
• ALWAYS check the security and the stability of the product on the adult chair before use.
• DO NOT use this product on stools or benches.
• This product is intended for children able to sit unaided (minimum 6 months) and up to 36 months or
a maximum weight of 15 kg.
• Suitable for adult chair size: seat width not less than 375mm, seat depth not less than 332mm, seat
backrest height not less than 310mm, seat backrest width not less than 385mm.
• ENSURE that the adult chair with the chair mounted seat is placed in a position where the child is not
able to use its feet to push against the table or any other structure as this can cause the tip over of the
adult chair supporting the chair mounted seat.
• DO NOT use the chair mounted seat if any part is broken, torn or missing.
• DO NOT use accessories or replacement parts other than those approved by the manufacturer.
• NEVER lift or carry child in booster seat.
• DO NOT use in motor vehicles.
Check what you have received...
You have received 1 box. Please check the contents of the box against the list below. If anything is missing, please contact Customer
Service. In Australia, contact CNP Brands on 1300 667 137, in New Zealand contact Wainhouse Distribution on 0800 567 5000.
Supplied loose in box:
Feeding Tray
x1
Due to variations in the style and design of our products, the photographs and illustrations shown in this instruction manual are generic, therefore product
fabrics, colour and design may vary from images shown. CNP Brands reserves the right to alter product specications without notice as a result of our
ongoing policy of product improvement.
Distributed in Australia by CNP Brands
20 Calarco Drive,
Derrimut, VIC, 3026
Customer Service 1300 667 137
W: www.cnpbrands.com.au
E: info@cnpbrands.com.au
F: www.facebook.com/CNPBrands
I: @cnp_baby
Distributed in New Zealand by Wainhouse Distribution
2-6 Argyle St, Morningside,
PO Box 41-014,
St Lukes, Auckland, New Zealand
Customer Service: 0800 567 5000
E: helpline@wainhousedist.co.nz
Seat (with seat insert pre-assembled)
x1
Ezi Feed
2-in-1 Booster
Model # 043052
IMPORTANT: RETAIN FOR FUTURE REFERENCE, READ CAREFULLY
ASSEMBLY OPERATING INSTRUCTIONS
To assemble feeding tray...
Align the feeding tray with the feeding
1a.
tray slots located on both sides of the
1
seat.
1b
Slide the feeding tray along the tray
slots on the seat, until the locking
buttons ‘click’ into place.
NOTE: Always check that the tray
is properly secure before use.
Feeding tray must always be
used when in booster seat mode.
Booster seat mode...
Place the Booster Seat on the seat of
1a.
1
NOTE: Only suitable for parent chair with: Seat width not less than
375mm. Seat depth not less than 332mm. Seat back height not less
than 310mm. Seat back width not less than 385mm.
the parent chair.
Ensure the back of the Booster Seat is
pressed up against the backrest of the
parent chair.
Secure the rst seat xing belt around
1b
the seat of the parent chair.
1c
Tighten the seat xing belt adjuster to
ensure the belt is secure.
1d
Secure the second seat xing belt
around the backrest of the parent chair.
1e
Tighten the seat xing belt adjuster to
ensure the belt is secure.
To remove feeding tray...
1
Floor seat mode...
1
Press and hold the locking buttons on
1a.
both sides of the tray.
1b
Whilst still holding the locking buttons,
slide the feeding tray away from the
seat.
Remove feeding tray from seat.
1a.
1b
Place seat directly onto the oor.
NOTE: NEVER use oor seat mode
on an elevated surface.
Removing seat pad...
1
Unfasten the safety harness.
1a.
Feed the 3 points of the safety harness
1b
backward through the holes of the
seat pad.
Lift seat pad up and out of the seat for
1c
cleaning.
NOTE: To re-install the seat pad,
complete these steps in reverse.
Safety harness...
1
To fasten safety harness, insert the left
1a.
and right hand side buckles into the
buckle housing.
1b
To release safety harness, press the
button on the buckle housing.
NOTE: Always adjust the waist
straps to t the child correctly.
HOW TO CARE FOR YOUR CHILDCARE SEAT
Cleaning
This product has been designed and developed with safety, comfort and functionality in mind. Please take the time to read this manual
carefully before using this product and keep it in a safe place for future reference. To ensure the long-lasting use of your Seat, wipe down with
a damp cloth and use a mild soap solution if necessary. Do not use abrasive cleaners. Always store product in a clean, dry place to air dry.
Maintenance
Always check parts regularly for tightness of screws, nuts and other fasteners – tighten or replace if required. To maintain the safety of your
toddler seat, seek prompt repairs for bent, torn, worn or broken parts. Use only those parts and accessories approved by CNP Brands.
Loading...